rinse chambers, 34" access doors on prewash
chamber
■ Variable speed conveyor 4-8.5 fpm
■ Start and stop switches at both ends
■ Doors open indicator
■ Load end ush system
■ Door interlocks
■ 3 H.P. TEFC prewash, power wash and power
rinse pump motors
■ Easy to remove wash arms
■ Easy to remove scrap trays and baskets
■ 301⁄2" wide conveyor
■ Insulated hinged doors
■ Front and rear panels
FLIGHT-TYPE DISHWASHER
MODEL
❑ FT900 – Flight-Type Dishwasher
OPTIONS AT EXTRA COST
❑ Energy Recovery – (will require a back
draft preventer)
❑ Electric Tank Heat
❑ Steam Tank Heat
❑ Booster Heater
❑ Electric
❑ Steam
❑ Blower Dryer
❑ Electric ❑ Steam
❑ 6" higher than standard chamber
❑ Prewash temperature control
❑ Multiple conveyor choices
❑ Circuit breakers
❑ Insulated counter balanced sliding doors option
❑ Optional conveyor speeds
❑ Other options available, consult factory
FT900 FLIGHT-TYPE DISHWASHER
DIRECTION OF OPERATION
❑ Right to Left
❑ Left to Right
VOLTAGE
❑ 208/60/3
❑ 240/60/3
❑ 480/60/3
❑ Other voltages available. Consult factory.
LA Research Report #M660004
ACCESSORIES
❑ Feet
❑ Extended
❑ Flanged
❑ Water hammer arrestor/PRV.
Specications, Details and Dimensions on Inside and Back.
F39628 – FT900 Flight-Type Dishwasher Page 1 of 12
FT900
FLIGHT-TYPE DISHWASHER
DESIGN: Fully automatic, ight-type dishwasher
machine consisting of a load section with power
recirculating prewash, an 8 foot power wash, power
rinse and nal rinse section. Included with each
machine will be exible plastic strip curtains to
control over spray.
CONSTRUCTION: Stainless steel tank and chambers
with No. 3 polish on appearance surfaces. Frame,
legs and feet to be constructed of stainless steel.
Inspection doors to be chamber width.
PUMPS: Recirculating stainless steel pumps with
stainless steel impellers. Pump housing has easy to
remove coverplate for access to impeller. All pumps
are self-draining. 150 gpm prewash; 292 gpm power
wash/power rinse.
MOTORS: Totally enclosed fan cooled design, with
inherent overload protection. Prewash, power wash
and power rinse motors to be 3 H.P. each, conveyor
1
⁄2 H.P. Available in electrical specications of
200-240/60/3 and 480/60/3.
CONTROLS: A stainless steel control center with
electronic digital controls mounted at eye level.
Power “On/Off” and “Start/Stop” switches integrated
into keypad. Digital display indicates door(s) open,
low temperature alert, tanks/nal rinse temperatures,
and other pertinent operating data. Additional “Start/
Stop” switches are located at each end of machine.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
FLIGHT-TYPE CONVEYOR: Stainless steel side
links, tie rods and conveyor tracks. Injection molded,
resilient Duraex ight links.
VENT: Single built-in vent duct with dampers
mounted in cleanable cross duct.
RECIRCULATING PREWASH SECTION: Prewash
compartment is tted with upper and lower wash
arms. Prewash ush down for prewash tank bed.
Large removable one piece perforated stainless
steel screen sloped downward to deep stainless
steel scrap basket.
TANK HEAT: Power wash and power rinse tank
water temperatures are thermostatically controlled.
Low water protection is provided. Specify either
electric or steam heat.
FINAL RINSE: Easily removed nal rinse arms.
CONVEYOR DRIVE UNIT: Powered by a 1⁄2 H.P.
motor. Trip mechanism provided on unload section.
Jam protection is provided by load sensing switch at
drive platform. Conveyor speed adjustment of 4 fpm
to 8.5 fpm is provided in the main control box.
DRAINS: Manual, hand operated, located in each
tank.
No other control system allows easier
monitoring.
The controls are placed in a convenient panel that
lets operators verify proper operation and temperatures at a glance.
Digital display
indicates the unit
is on, and conrms
that the doors are
closed. Automatic
door interlocks
prevent the pump and conveyor from operating if the
doors are open. Easy-to-read digital display indicates
accurate temperatures of the 150°F wash, 160°F
power rinse, 160°F dual rinse and 180°F nal rinse —
critical for proper HACCP system record-keeping.
Page 2 of 12 F39628 – FT900 Flight-Type Dishwasher
Stainless steel pump
is built for long life.
The stainless steel pump
housing and impeller
offer greater durability
and long life. The pump
motor is totally enclosed
and fan cooled (TEFC)
to protect it from water
spray during dishroom
clean-up. The pump
is also externally mounted to the frame for added
rigidity and easy access to the clean-out port.
FT900
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Scrap baskets
capture food
particles and are
easy to clean.
The sloped screens
that carry scraps to
the scrap baskets
are steeper, so less
soil gets into the
tanks. The basket opening is larger for easy cleaning
and basket handles have been designed for easy liftout access.
The FT900 Series saves
water and energy.
The unit is designed to cut
water and energy usage,
yet provide effective
cleaning and sanitizing that
meet NSF International
requirements.
This is achieved through a
carefully balanced ratio of
water ow to pressure.
At 292 gallons per minute (gpm), the machine offers excellent wetting and
ooding over ware. Insulated doors also reduce heat
loss. The unit’s 2.2 gpm/120 gallons per hour rinse
ow rate (the lowest in the industry on a standard
machine) saves both water and the energy to heat it.
The conveyor on the FT900 Series is wider so it can
handle more ware. Result: more volume and versatility, quicker work.
Its speed is servicer
adjustable for the
type of ware, soiled
condition, or workforce requirements.
It can be adjusted
from 4 to 8.5 feet
per minute.
FLIGHT-TYPE DISHWASHER
Optional Energy
Recovery system.
The optional Energy
Recovery system
captures escaping
heat and steam from
the exhaust air and
uses a heat exchanger to recycle it into energy.
This free energy is used to preheat the incoming
water supply before it enters the booster heater. The
cold ground temperature water passes through a
heat exchanger positioned directly in line with the
machine’s exhaust system to capture the energy
from the exhaust air to elevate the temperature of the
water to 128° before it enters the booster heater.
Flush arm keeps
load end clean.
The load end also has a
readily removable ush arm
to rinse food scraps into the
prewash area scrap basket.
Self-draining pumps help keep water clean.
Pumps are self-draining when the machine is shut
down, so there is no residual water left in the pumps.
Installation is quick and easy with modular
design, minimal wiring connections, and
single point vent.
Modular design means the FT900 installs quickly,
and reliably. Sections t through 42" doors. The
control panel is already in place, premounted to the
power wash/power rinse/nal rinse section.
Wiring connections
are minimal, and there
is only a single vent
connection, saving
time and expense.
The control box uses a
“single plane” circuitry
design for easy accessibility during installation and service. The FT900 is
ready to run quickly.
F39628 – FT900 Flight-Type Dishwasher Page 3 of 12
FT900
ELECTRIC L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 4 of 12 F39628 – FT900 Flight-Type Dishwasher
FT900
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
ELECTRIC L-R
140°
F39628 – FT900 Flight-Type Dishwasher Page 5 of 12
FT900
ELECTRIC R-L
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 6 of 12 F39628 – FT900 Flight-Type Dishwasher
FT900
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
ELECTRIC R-L
140°
F39628 – FT900 Flight-Type Dishwasher Page 7 of 12
FT900
STEAM L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 8 of 12 F39628 – FT900 Flight-Type Dishwasher
FT900
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STEAM L-R
F39628 – FT900 Flight-Type Dishwasher Page 9 of 12
FT900
STEAM R-L
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 10 of 12 F39628 – FT900 Flight-Type Dishwasher
FT900
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STEAM R-L
F39628 – FT900 Flight-Type Dishwasher Page 11 of 12
FT900
FLIGHT-TYPE DISHWASHER
FT (ight type) Models—many additional variations of
these model specications are available. Engineering
data furnished on request.
Flight-type dishwasher with BLOWER-DRYER OPTION
has the same specications as the Basic FT900 Series
EXCEPT for one additional Blower Motor (2 H.P. —
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
208-240/60/3 and 480/60/3) and is available on any model
Numbers in parentheses, after model number from left to
having either a 9 or 11 foot Unloading section.
right, represent length in feet of the following respectively;
Loading section, Washing and Power Rinsing sections,
Unloading section.
Entire FT900 Series is listed by UL and NSF and meets
requirements of ASSE Standard No. 1004.
FT900 Series (5, 7 Load / 8 Center / 5, 7, 9, 11 Unload)*
Machine Ratings (Mechanical)
Conveyor Speed — Feet per minute4 - 8.5
Dishes per Hour14,316
Floor Space - Feet — Machine length plus 101⁄2"
total for load and unload platform overhangs
Overall Dimensions (H x W) — inches (standard height)8011⁄16 (C) x 47 (B)
Final Rinse — Minutes of operation during one
hour of continuous operation60 at continuous loading condition
Rate of Final Rinse — Gallons per minute
at 20 PSI ow pressure2.0
Final Rinse Consumption — Gallons per hour
at 20 PSI ow pressure120
Exhaust Requirements — Cubic feet per minute
without Blower Dryer
Electric Heat Requirements —
Tank Heat - Kilowatt (Regulated)
Optional Electric Booster - Kilowatt
Steam Heat Requirements —
Steam Consumption
Tank Heat - Pounds per hour - maximum
(Regulated) - based on 15 to 52 PSI steam at
the machine and on the customer supplying
nal rinse water at minimum (A) (20 PSIG)
Optional Steam Booster - Pounds per hour - maximum
- based on 20 PSI steam at 20 PSI water owing 120°F incoming water raised to 190°F (70°F rise)
(180°F minimum)
Peak Rate of Drain Flow — Gallons per minute
Initial rate with full tanks38
Shipping Weight CratedVaries by individual model - consult your Hobart representative
Disconnect switches are recommended for each power circuit connected
to dishwasher. These disconnect switches are NOT furnished by Hobart
and should be installed by the electrical contractor at the time of installation.
30KW - 105°F incoming water raised to 190°F (85°F rise) (180°F minimum)
Approximately 30 lbs. per hour = 1 boiler H.P. (BHP)
175 lbs./150°F Wash minimum/160°F Rinse minimum
99 lbs.
(A) If only 10-12 PSIG Steam Pressure available at machine - specify Low Pressure Steam Option.
(B) With all rear panels and plumbing removed, machine width is 391⁄8".
(C) Highest item is control box - 8011⁄16". Can be adjusted lower 2" for door clearance.
NOTE: Refer to specic specication sheets for short machines (FT900S) machines with Blower-Dryers.
As continued product improvement is a policy of Hobart, specications are subject to change without notice.
Page 12 of 12 F39628 – FT900 Flight-Type Dishwasher
F39628 (REV. 05/13) LITHO IN U.S.A. (H-01)
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.