Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
CLPS66e
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STANDARD FEATURES
■ 202 racks per hour
■ Opti-RinSe™ system
■ Rapid Return Conveyor Drive Mechanism
■ Insulated hinged double doors with door
interlock switches
■ 19.5 inch chamber height opening
■ Top mounted micro-processer control module
■ Energy saver mode
■ Dirty water indicator
■ Low temperature alert
■ Conveyor dwell
■ Delime notication
■ Service diagnostics
■ NAFEM Data Protocol compliant
■ Computational Fluid Dynamic Designed Self-
Aligning Wash Manifolds
■ Stainless steel debossed anti-clogging wash
arms
■ Removable Integrated Pump Intake Screen
■ Stainless steel self-draining pumps and impellers
■ Single, sloping scrap screen and deep basket
■ Stainless panels enclose perimeter and bottom
■ Door actuated drain closure
■ Single point electrical connection (three phase
only), does not include the booster heater
■ Convertible hot water or low temp nal rinse
■ Vent fan and booster heater control
DISHWASHER
MODEL
❑ CLPS66e – Dishwasher
OPTIONS AT EXTRA COST
❑ Stainless steel pressure-less 15/30 KW booster
heater
❑ Higher than standard chamber
ACCESSORIES
❑ Stainless steel vent hoods
❑ Direct drive unloader
❑ Side loader
❑ Blower-dryer
❑ Drain water tempering kit
❑ Flanged feet kit (requires 3 kits)
Specications, Details and Dimensions on Inside and Back.
CLPS66e DISHWASHER
DIRECTION OF OPERATION
❑ Right to Left
❑ Left to Right
VOLTAGE
❑ 208/60/1 ❑ 240/60/1 ❑ 380/60/3
❑ 208/60/3 ❑ 240/60/3 ❑ 480/60/3
❑ 600/60/3
F40211 – CLPS66e Dishwasher Page 1 of 12
Shown with optional vent hoods
CLPS66e
DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
THE CLe WAREWASHER IS NOW STANDARD WITH MORE EFFICIENT FEATURES THAN EVER . . .
Inside and out the CLe warewashers by Hobart are packed with standard components and patented design
innovations that make them the biggest value in the dishwasher industry.
Wash Manifolds. Patent pending Computational
The insulated hinged inspection doors provide easy
access in the chamber. Exterior wash pipes and
reduced interior bafes reduce clean-up time.
The Rapid Return drive allows for a wide separation
between the wash and the rinse zone.
Fluid Dynamic designed wash manifolds are selfaligning and come with Hobart’s signature debossed
anti-clogging nozzles for superior result.
The Hobart exclusive microprocessor control module
offers a choice of many features, such as an exclusive
Energy Saver Mode, Low Temperature Alerts, and
Dirty Water Indicator. It also displays pertinent
machine status and has a Delime Notication. The
controls have built-in Service Diagnostics and are
NAFEM Data Protocol Compliant.
Soil Management System. Screen design sheds soil
more easily than at screens, reduces frequency of
cleaning — easy to empty large soil particles . . . Just
lift out the scrap basket.
Opti-RinSe™. Hobart’s exclusive Opti-RinSe™ signi-
cantly reduces operating cost by reducing rinse water
and the energy required to heat the water. The unique
spray pattern uses large droplets to more efciently
sanitize the ware.
OTHER STANDARD FEATURES . . .
• Thermal Layer Curtains help keep the heat inside
the machine.
• Ball Detent Clutch Conveyor Drive for maximum
protection against conveyor Jams
• Integrated Removable Pump Intake Screen to
offer the ultimate guard of keeping debris from
entering the pump.
• Hinged Door Seals and stainless steel labyrinth seal
for drip-free operation
• Low-Temp Convertibility In Field. All machines
shipped hot. Change software in eld at set up to
low temperature if desired – then, if requirements
change, convert from one mode to the other in the
eld. An exclusive feature – standard from Hobart.
• Door Actuated Drain Closure. Closing the door
automatically actuates drain closure, eliminates
extra manual steps, ensures that closure is in the
correct position.
Page 2 of 12 F40211 – CLPS66e Dishwasher
CLPS66e
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
AVAILABLE OPTIONS AND ACCESSORIES . . .
Flexibility is synonymous with Hobart CLe dishwash ers. If your operation demands a dishwasher with a
vent hood, an extended hood . . . a power scrapper,
just specify the combination of options that suit your
needs.
Built-in Pressureless Stainless Steel Booster Heater.
Interwired and interplumbed. Saves on installation and
saves oor space. Simplies operation with just one
switch to power dishmachine and booster.
Side Loader. Save up to 20 square feet in the dishroom
layout with an optional C-Line Side Loader. Racks are
indexed 90° into the dishwasher automatically – a
feature that cuts space and reduces labor dramatically.
Your dishroom team will appreciate this feature.
OTHER AVAILABLE ACCESSORIES . . .
Blower-dryer, steam booster heater, and a singlepoint electrical connection to include electric booster
heater.
Machine Ratings (Mechanical)
Racks per hour (193⁄4" x 193⁄4") 202
Conveyor Speed - feet per minute 5.6 max.
Dishes per Hour (Average 25 per rack) 5,025
Glasses per Hour (Average 45 per rack) 9,045
Floor Space – Table to Table (Inches) 66
Overall Dimensions – H x W x D (Inches) 681⁄2 x 663⁄4 x 301⁄4
Motor H.P. Power Scrapper 2
Conveyor Drive H.P.
Number of Wash Tanks 2
Tank Capacity – Gallons Power Scrapper 23
Pump Capacity –
Gallons per Minute - Weir Test 165
Heating Equipment –
(For keeping power wash hot)
Gas Burners (with Natural Gas) 78,000 BTU per hr.
Electric Heating Unit – Size Used 15 KW
Optional Booster Heater / Final Rinse 15 KW / 30 KW
Rinse – Minutes operated during hour of
maximum operation 60
Final Rinse Flow – Gals. per min.
At 15 PSI Flow Pressure 1.8
At 20 PSI Flow Pressure 2.1
Final Rinse Flow – Gals. per hr. – MAXIMUM
At 15 PSI Flow Pressure 108
At 20 PSI Flow Pressure 126
Rinse 20 PSI Flow Pressure
Gal./Rack
Steam Consumption –
Pounds per hr. - MAXIMUM
Approx. 30 lbs. per hr. = 1 boiler H.P. (BHP)
Dishwasher, based on 20 PSI steam and
on customer supplying final rinse water
at 180°F maximum 65
Steam Booster, if used on 20 PSI steam 20 PSI water flowing - 130°F entering
water raised to 180°F min. 60
Exhaust Requirements –
Cubic Feet per minute
Peak Rate of Drain Flow – Gallons per minute.
(Initial rate with full tank) 38
Shipping Weight Crated – Approximate lbs. 613
DISHWASHER
CLPS66e
Wash 2
1
⁄6
Wash 23
Hot Water Sanitizing -
Chemical Sanitizing
.62 - 180°F – .62 - 120°F
Entrance End 200
Discharge End 400
F40211 – CLPS66e Dishwasher Page 3 of 12
CLPS66e
DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 4 of 12 F40211 – CLPS66e Dishwasher
CLPS66e
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DISHWASHER
F40211 – CLPS66e Dishwasher Page 5 of 12
CLPS66e
ELECTRIC L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 6 of 12 F40211 – CLPS66e Dishwasher
CLPS66e
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
ELECTRIC R-L
F40211 – CLPS66e Dishwasher Page 7 of 12
CLPS66e
GAS L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 8 of 12 F40211 – CLPS66e Dishwasher
CLPS66e
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
GAS R-L
F40211 – CLPS66e Dishwasher Page 9 of 12
CLPS66e
STEAM L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 10 of 12 F40211 – CLPS66e Dishwasher
CLPS66e
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STEAM R-L
F40211 – CLPS66e Dishwasher Page 11 of 12
CLPS66e
DISHWASHER
SPECIFICATIONS: Meets requirements of A.S.S.E. Standard No.
1004.
DESIGN: Semi automatic, high or low temperature single-tank,
rack-type dishwasher with exible thermal layer curtains at
the ends of chamber and between wash and nal rinse zones.
Insulated hinged inspection doors located in front of machine
provide easy access to wash arms, rinse arms, strainer, strainer
basket, and pump intake screen. Length of machine inside tank
(at table connection) 66". Machine designed to clean and sanitize
with hot water 160°F wash and 180°F (minimum) nal rinse, or
low temperature 130°F wash and 120°F nal rinse and a chemical
sanitizer. Water hardness recommended to be 3 gr. for best results.
Automatic interlocks shut off pump and conveyor if door is opened
when machine is in operation.
CONSTRUCTION: Tanks, chambers, frame, legs, control box,
doors, and all panels are constructed of stainless steel.
PUMPS: The two recirculating stainless steel pumps and impellers with ceramic seat seals. Easily accessible pump assembly
permits quick inspection. The pumps are self-draining. All piping
distributing water to the upper and lower wash arms is stainless
steel tubing.
PUMP MOTORS: Built for Hobart 2 hp grease-packed ball
bearings, splash proof, ventilated with manual, resettable inherent
overload protection. Available in electrical specications of 208240/60/1, 208-240/60/3, 480/60/3 and 600/60/3. Also available, but
not submitted for UL listing are 200-240/50/3 and 380-415/50/3.
CONTROLS: A stainless steel control module with power and
“start/stop” buttons is mounted on top of the machine. Machine
control circuitry will be operated from a 120-volt control circuit
transformer. Electrical components are completely wired with
105°C, 600V thermoplastic insulated wire with stranded conductors
routed through UL listed electrical conduit or covered wire way.
CONVEYOR: Rapid Return drive, designed for more even throughput of racks and allows for a 16-inch separation between the wash
and the rinse zone. Racks conveyed automatically through wash
and rinse zones and onto clean dish table. Ball Detent Clutch drive
prevents damage to machine or racks, should movement of racks
be obstructed. Rack tracks, conveyor structure, and drive units
of stainless steel for 193⁄4" x 193⁄4" racks as standard. Conveyor
speed: 5.6 FPM.
DRIVE MOTOR: Built for Hobart, 1⁄6 horsepower gear motor,
ventilated with manual, resettable inherent overload protection.
Available in electrical specications of 208-240/60/1, 208-240/60/3,
480/60/3 and 600/60/3. Also available, but not submitted for UL
Listing are 200-240/50/3 and 380-415/50/3.
POWER SCRAPPER: CLPS66e power scrapper is equipped with
an upper and lower wash arm with specially shaped nozzles having
large openings and arranged to effectively scrap all types of tableware. Power scrapper arms and end caps are easily removable for
cleaning without use of tools. Removable perforated stainless steel
strainer pans support a deep perforated stainless steel basket.
Basket and strainer pans (3) can be removed without lower wash
arm removal.
POWER WASH: Wash tank is equipped with upper and lower
stainless steel CFD Wash Arms which effectively direct water jets
to all ware surfaces. Both upper and lower wash arms are selfaligning and have easily removable end caps for cleaning without
use of tools. A removable perforated stainless steel strainer pan
supports a deep perforated stainless steel basket.
FINAL RINSE: Final rinse ow rate: 2.1 gpm, .62 gpr, 126-gph.
Stainless steel upper and lower Auto Position Rinse Arms™ have
single rows of nozzles. Racks entering the rinse zone automati-
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
cally trigger rinse. Final rinse water line is equipped with a vacuum
breaker downstream of an electrically operated solenoid valve in
common piping system. Rinse agent and Low Temp Final Rinse –
Sanitizer agent (5.25% sodium hypochlorite – bleach) dispenser
injection ports provided in nal rinse piping above chamber. Cau-
tion: Certain materials, including silver, aluminum, and pewter are
attacked by sodium hypochlorite (bleach) in the chemical sanitizing
dishwasher mode of operation.
FILL: Fill water line is equipped with vacuum breaker on downstream side of electrically operated solenoid valve in common
piping system, for automatic maintenance of tank level.
DRAIN AND OVERFLOW: Large bell-type automatic overow
and drain valve inside power scrapper tank controlled from inside
of machine. Power scrapper overows to drain. Wash tank drain
controlled from inside of the machine overows to power scrapper
through large internally mounted stainless steel tubing. Drain seals
are large diameter high temperature o-rings. Drain automatically
seats by closing inspection doors. Common drain utilizes a removable large diameter stainless steel tube sealed by rubber o-rings
at each drain housing. Drain housing can be plumbed from load or
unload end of machine.
STANDARD EQUIPMENT: Digital display of power scrapper, wash
and nal rinse temperature. Positive low water protection for tank
heat. Thermal Layered Curtains throughout machine are keyed to
ensure proper placement. Drains are automatically closed when
inspection doors are closed. Stainless steel adjustable feet. Bolted
stainless steel enclosure panels around perimeter and underneath
machine. Automatic tank ll. Door interlocks. Auto-timer. Vent fan
and booster heater controls. Single point electrical connection.
Low temperature alerts. Service diagnostics. Dirty water indicator.
Delime notication. Conveyor dwell. Energy Saver Mode. NAFEM
Data Protocol compliant.
WASH TANK HEATING SELECTIONS (must choose one):
ELECTRIC: One electric Incoloy® sheathed immersion heater
(15 KW) removable from inside tank. Tank water temperature is
controlled by microprocessor controlled thermostat with positive
low-water protection and magnetic contactor. (Disconnect switches
not furnished.) A high limit device mounted on the surface of the
tank additionally protects heating element.
STEAM: One-inch stainless steel steam coil. Tank water temperature controlled by microprocessor controlled thermostat with
positive low-water protection. Steam supplied to machine through
high temperature steam solenoid valve and line strainer.
GAS: Regulated infrared immersion tube gas burner system.
Microprocessor controlled thermostat and a blower with a pressure
switch control tank water temperature. Positive low water protection is provided. A high limit device mounted on the surface of the
tube additionally protects immersion tube. A solid-state igniter
board controls the gas valve and provides ame ignition. A transformer steps the control circuit voltage down from 120 volts to
24 volts to power the igniter board and gas valve. For natural gas,
gas pressure to burner (customer connection) not to exceed
7" W.C. For LP gas, gas pressure to burner (customer connection) not to exceed 11" W.C. If gas pressure is higher than 7" W.C.
natural or 11" W.C. LP pressure regulating valve must be supplied
(by others) in the gas line to the dishwasher.
OPTIONAL EQUIPMENT AT EXTRA COST:
Stainless steel pressureless booster heater. Stainless steel vent
hoods with vent stack and locking-type damper. Higher than
standard chamber. Side loaders and unloaders. Floor mounted
steam booster. 193⁄4" x 193⁄4" peg, combination and miscellaneous
racks. Table limit switch. Drain water tempering kit.
As continued product improvement is a policy of Hobart, specications are subject to change without notice.
Page 12 of 12 F40211 – CLPS66e Dishwasher
F40211 (REV. 10/14) LITHO IN U.S.A. (H-01)
Loading...