Hobart D340 User Manual

D340 MIXERS

D340 W/BRAKE ML - 104484

D340 W/O BRAKE ML - 104483

D340 MIXER

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

FORM 19104 Rev. A (8-98)

MODEL D340 MIXER

– 2 –

2345678901234567890123456789012123456789

The D340 Mixer is a medium duty mixer which develops 11/2 horsepower and features a timer, thermal overload protection, and a #12 attachment hub as standard equipment. A variety of agitators are available for use on either the standard 40 quart bowl or the optional 30 quart bowl. A special 20 quart bowl and agitators are available options.

Bowl Guard is standard equipment on all D340 models.

23456789012345678901234567890121234567890123456789012345678901212345678901

Installation, Operation, and Care of

MODEL D340 MIXERS

SA VE THESE INSTRUCTIONS

GENERAL

Programmable Timer Controller is optional on D340 models. A variety of attachments and accessories are available for all mixers. These are described in a separate

Use and Applications Handbook

which is furnished with each mixer.

INSTALLATION

UNPACKING

Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.

Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate.

LOCATION

Place the mixer in its operating location. There should be adequate space around the mixer for the user to operate the controls and install and remove bowls. The area above the mixer should allow the top cover to be removed for routine maintenance and servicing.

Holes are provided in the base for permanent bolting to the floor, although this is not necessary in normal installations. Four plastic plugs are supplied with the mixer to plug these holes if they are not used.

ELECTRICAL CONNECTION

– 3 –

WARNING: ELECTRICAL AND GROUNDING CONNECTION MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.

WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.

ELECTRICAL DATA

Models Volts / Hz / Ph

D340 120 / 60 / 1 25.0 35 35 8 35 35 8 D340 208 / 60 / 1 14.0 20 20 12 20 20 12 D340 240 / 60 / 1 12.5 20 20 12 20 20 12 D340 208 / 60 / 3 5.0 15 6 14 15 10 14 D340 240 / 60 / 3 5.0 15 6 14 15 10 14 D340 480 / 60 / 3 2.5 15 3 14 15 6 14

Rated

Amps

Circuit Size

(Amps)

* Dual Element

Fuse Size *

(Amps)

Time-Delay Fuse

60°C Copper

Wire Size

Circuit Size

(Amps)

** Inverse Time

Circuit Breaker **

(Amps)

Circuit Breaker

60°C Copper

Wire Size

Circuit Size (Minimum) & Fuse / Circuit Breaker Size (Maximum) compiled in accordance with the National Electrical Code (ANSI/NFPA 70), 1993 Edition.

A hole for 3⁄4" trade size conduit is located at the top of the pedestal (Fig. 1). Make electrical connections per the wiring diagram located on the inside of the Top Cover.

Fig. 1

Check Rotation (Three-Phase Machines Only)

Three-phase machines must be connected so the planetary rotates in the direction of the arrow on the Drip Cup. To check rotation:

Set the gear shift lever on 1. Apply power to the mixer, set the Electro-Mechanical Timer on HOLD; or, if equipped with a

Programmable Timer Controller, set it on [ -- : -- ]. With the Bowl Support all the way up, momentarily run the machine by pushing the START and then STOP buttons.

If rotation is incorrect, DISCONNECT ELECTRICAL POWER SUPPLY and interchange any two of the incoming power supply leads.

– 4 –

+ 8 hidden pages