CARRYING HOLDER for MARCHING BELLS XYLOPHONE
MKH-9200(S)
OWNER’S MANUAL
Thank you for purchasing the Yamaha Carrying Holder for Marching Bells and Xylophones.
Please read this Owner’s Manual throughly before use.
Accessories
Hexagonal Wrench |
4mm |
|
ZN39960 R0
Printed in Japan
■ |
|
■ |
|
|
|
||
|
|
|
|
|
|
||
|
|||
|
|
||
|
|
||
|
|
|
|
|
|
||
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
||
|
|
||
|
|
||
|
|
|
|
|
A |
|
|
|
|||
|
|
|
|
|
|
||
|
|
||
|
|
||
|
|
||
|
|
||
|
|
||
|
|
|
|
A |
|
||
|
|
||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAUTION
Securely tighten all screws after adjusting the instrument’s position. Loose screws may cause the instrument to slip or produce noise during playing.
Therefore, always check and re-tighten all screws before using the instrument.
To tighten the arm section screws, use the hexagonal wrench provided.
Be very careful when removing the carrying holder and drum. Never drop or throw them.
As far as possible, avoid using the drum and carrying holder outside when it is raining. Wipe any wet parts immediately with a soft, dry cloth.
To clean the carrying holder, wipe with a soft, dry cloth. Never use solvents such as paint thinner or benzine.
When tilting up the marching bell/xylophone make sure that the tone bars do not hit against the holder.
Always take suitable breaks when playing the instrument for a long period of time.
When tilting up the marching |
A |
|
bells/xylophone always hold the |
||
|
||
instrument with your hand as it |
|
|
might flip back and injure bystanders. |
|
|
When tilting the instrument up or |
|
|
returning it to the playing position, |
|
|
keep your hands away from |
|
|
the areas marked A as |
|
|
shown in the illustration. |
|
|
Hands and/or fingers can |
|
|
get caught in this area |
|
|
resulting in injury. |
|
ASSEMBLY PROCEDURE
MXL-32A, 32AF
MKH-9200(S) MBL-32A, 832A
1 Carrying Holder Setup
First adjust the bracket position to a comfortable fit.
Attach the arms that are supplied with the
Multi Toms.
|
|
|
|
Arm |
|
|
||
Bracket |
||
|
Loosen |
Tighten
3 2 |
|
|
|
(MKH-9200: 3 MKH-9200S: 2 ) |
|
One of three or two bracket mounting positions |
3 2 |
can be selected. |
3 or 2 positions |
(MKH-9200: 3 positions, MKH-9200S: 2 positions) |
|
2Attach the Instrument
2.A
4.4 B
5.A
1.Lay the Marching Bells/Xylophone face down.
2.Use a hex wrench to loosen the four screws A on the carrier frame so that the brackets can slide.
3.Set the carrier frame on the instrument, as shown in the illustration below, and slide the brackets on the carrier frame so that they align with the carrier mounting plates on the bottom of the instrument.
4.Use the four fixing bolts B on the brackets to attach the carrier frame to the instrument. Tighten the four bolts little by little and secure.
5.Use the hex wrench to firmly tighten the carrier frame’s screws A .
*To remove the carrier frame, loosen the fixing wing bolts only.
*If you are having trouble reattaching the carrier frame after it has been removed, go through the same procedure as described above.
|
|
Carrier Frame |
Carrier mounting plate |
Brackets with wing bolts
Fixing wing bolt
B |
|
|
B |
Fixing wing bolt |
|
Pivot holder |
B |
|
|
|
|
A |
|
B |
|
|
|
A |
|
A |
|
|
|
|
|
A |