XE-A102 Quick Start Guide
English
The following describes how to get your cash register ready to operate. Follow these steps when you use the cash register for the first time.
1Initializing the Cash
Register
To ensure the cash register operates properly, initialize it using the following procedure:
1.With the power cable unplugged, insert one of the supplied mode keys into the mode switch and turn it to the REG position.
|
REG |
OFF |
X/Flash |
VOID |
Z/PGM |
|
2.Insert the plug of the power cable into the AC outlet.
IMPORTANT
This operation must be performed without batteries loaded.
The buzzer will sound three times.
3.Now the cash register has been initialized. The register display will show “0.00” with “ ” .
The following are supplied with your cash register.
1 paper roll
2 mode keys
2 drawer lock keys
1 instruction manual (English)
1 instruction manual (Spanish)
1 Quick Start Guide
1 ink roller (pre-installed)
1 take-up spool
1 mounting bracket
2 |
Installing Batteries |
3 Roll |
|
Installing a Paper |
Install batteries for back-up of sales data and programmed contents.
1.Push the printer cover forward and detach it.
2.Open the battery cover next to the paper roll cradle.
1.Place a paper roll in the paper roll cradle so that the paper unrolls from the bottom.
2.Insert the paper straight into the paper inlet, and press the fkey. The inserted end comes out at the printing area.
View from rear
3.Insert three new “AA” batteries. (Batteries are not supplied with the cash register.)
3.(For journal printing) Insert the top end of the paper into the slit in the take-up spool shaft and wind the paper two or three turns. Then place the take-up spool on the bearing.
View from rear
4.When the batteries are properly installed,
“” on the display will disappear. Close the battery cover.
IMPORTANT
Improper use of batteries may damage the cash register. Please take the following precautions.
•Be sure that the positive (+) and negative (-) poles of each battery are oriented properly.
•Never mix batteries of different types. •Never mix old batteries and new ones.
Please read the instruction manual for other battery handling precautions.
4. Attach the printer cover.
(For receipt printing, step 3 should be omitted.)
4 Basic Programming
Turn the mode switch to the Z/PGM postition.
REG
OFF X/Flash
Z/PGM
VOID
Setting the Time
Enter the time in 4 digits (“hhmm” format) using the 24 hour
#/ |
key once to program the next item |
|
system. Press the SBTL |
||
or twice to exit the programming mode. |
|
|
Example: |
#/ |
#/ |
|
SBTL |
SBTL |
Time (2:30 p.m.)
5 Now, you are ready!
Before Starting Entries
Turn the mode switch to the REG postition.
|
REG |
OFF |
X/Flash |
VOID |
Z/PGM |
|
Enter a clerk code (1-4) and press CLK# . (Once the clerk code entered, re-entry of the clerk code is not needed until the clerk is changed.)
1 CLK#
Setting the Date |
Clerk code |
Enter the date in 6 digits using the month-day-year
#/ |
key once to program the next item |
|
format. Press the SBTL |
||
or twice to exit the programmig mode. |
|
|
Example: |
#/ |
#/ |
|
SBTL |
SBTL |
Date (March 15, 2006)
Setting Tax Rates (%)
Specify a tax rate (%) for calculation of tax on each taxable subtotal using the following sequence:
9 |
SBTL Tax number (1-4)* @/TM R |
|
#/ |
@/TM Q
R:Tax rate (0.0000% to 99.9999%)x10000
(Enter the rate in 6 digits. Leading zeros may be omitted.)
Q: Minimum taxable amount (0.01 to 99.99)x100
(Smallest amount for which tax must be collected. ) *Up to 4 types of tax are programmable.
Example:
#/ |
@/TM |
@/TM |
SBTL |
Tax 1 |
Tax rate (7.0000%) |
Min. taxable |
|
|
amount ($0.11) |
NOTE
Your cash register is pre-programmed so that you can use it with minimum set-up. To change the settings, see the instruction manual.
Initial settings
Departments 1-4: Taxable 1
Departments 5-8: Non-taxable
Registration Example
(When the Customer Pays by Cash)
5
CLK#
1
Clerk code Price and dept.
7 #/
3 |
SBTL |
|
|
Price and dept. |
|
Amount tendered
Reading and Resetting
X Reports (reading)
Turn the mode switch to the X/Flash
position and press |
. |
Z Reports (reading and resetling)
In the Z/PGM mode, press |
.(In this |
case, grand total resetting is not performed.)
Flash Reports (displayed but not printed)
In the X/Flash mode:
Press dept. key for dept. sales reports
Press #/ for sales total reports
SBTL
Press CH for cash-in-drawer reports
For further information, please read the instruction manual.
Printed in China/Impreso en China |
O(TCADH2488RCZZ) 1 |