Parkside PKZ 180 A1 User Manual [en, cs, de]
IAN 93472
COMPRESSOR PKZ 180 A1
COMPRESSOR
Operation and Safety Notes
Translation of original operation manual
KOMPRESOR
Pokyny pro obsluhu a bezpečnostní pokyny
Překlad originálního provozního návodu
KOMPRESOR
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
KOMPRESSOR
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
93472_Kompressor_PKZ_180_A1_cover_SI-CZ.indd 2 15.11.13 14:03
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB Operation and Safety Notes Page 5
SI Navodila za upravljanje in varnostna opozorila Stran 15
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 25
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 35
93472_Kompressor_PKZ_180_A1_cover_SI-CZ.indd 3 15.11.13 14:03
1 2
3
4
A
C
5
6
7
8
9 10 16 15
11
12
13
14
B
4
9
3
D
5
6
9
93472_Kompressor_PKZ_180_A1_cover_SI-CZ.indd 4 15.11.13 14:03
7
9
93472_Kompressor_PKZ_180_A1_cover_SI-CZ.indd 6 15.11.13 14:03
Table of contents
Introduction
Intended use ........................................................................................................................................ Page 6
Improper use .......................................................................................................................................Page 6
Features ...............................................................................................................................................Page 7
Technical Data ....................................................................................................................................Page 7
General safety instructions for air tools ............................................................... Page 7
General safety information for electrical devices
Product-specific safety instructions .....................................................................................................Page 9
Before use ....................................................................................................................................... Page 10
Start-up
Switching the compress on / off ......................................................................................................... Page 10
Establishing connections ..................................................................................................................... Page 10
Using the tyre filling device ................................................................................................................Page 10
Using the blow-out gun ....................................................................................................................... Page 10
Using the adapter set .......................................................................................................................... Page 11
Cleaning / Care ............................................................................................................................ Page 11
Spare parts .................................................................................................................................... Page 11
Maintenance and Service .................................................................................................. Page 11
Information about warranty and service processing ............................... Page 11
Warranty terms ...................................................................................................................................Page 12
Scope of warranty ..............................................................................................................................Page 12
Processing of warranty claims ............................................................................................................ Page 12
Environmental instructions and disposal information .............................. Page 12
EC Declaration of Conformity ......................................................................................... Page 13
5 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 5 15.11.13 14:03
Introduction / General safety instructions for air tools
Introduction
Compressor PKZ 180 A1
Introduction
Congratulations! You have chosen a
high-quality device from our company.
Familiarise yourself with the product
before using it for the first time. In addition, please
carefully refer to the operating instructions and the
safety advice below. Initial operation of this device
must be performed by trained personnel.
KEEP OUT OF THE REACH OF CHILDREN!
Intended use
This device is suitable as a compressed air supply
for tyre filling devices, blow-out guns and with the
respective adapters for inflating balls, etc. Only use
the product as described and for the specified applications. Keep these instructions in a safe place.
When passing this product on to others, please also
include all the documents. Any use other than the
intended is prohibited and potentially dangerous.
Damages resulting from noncompliance or misuse
are not covered by the warranty and are not included
in the manufacturer‘s liability. This device was designed for household use and may not be used for
commercial or industrial purposes.
Improper use
The compressor is not suitable for continuous use or
unrestricted commercial use, and may only be used
in dry rooms. The compressed air produced is not
suitable as respiratory air. Use in explosive environments and aiming the compressed air gun at persons
is prohibited.
Remaining risks
Even with proper use of the device there always is
a certain remaining risk which cannot be eliminated.
The type and design of the device can infer the following potential risks:
- The user forgets to use ear protection.
- The user opens the valve without the device being
connected to an air hose.
- Compressed air is aimed at persons or animals.
- Dirt particles and dust raised enter the eyes or the
face.
- Electric shock when touching non-insulated electrical
components.
Failure to follow the instructions in your instructions
for use may result in other remaining risks due to
improper use.
Warning: The actual vibration emission during use
may deviate from that specified in the instructions
for use or by the manufacturer. This can be caused
by the following influencing factors which should
be considered before or during every use:
- Is the device being used properly?
- Is the type of material to be worked on correct?
- Is the device in proper working condition?
- Are the handles or optional vibration handles
installed and are these properly attached to the
device?
If you experience discomfort or discolouration of
the skin on your hands during use, stop working
immediately. Take adequate breaks. Failure to take
adequate breaks can result in hand-arm vibration
syndrome. You should assess the utilisation factor
according to the work or use of the device, and take
appropriate breaks. This will significantly reduce
the utilisation factor throughout working. Minimise
the risk you are exposed to by vibration. Maintain
this device as specified in the instructions for use. If
the device is used more frequently, please contact
your speciality retailer and, if necessary, purchase
anti-vibration accessories (handles).
Avoid using the device in temperatures of t=5 °C
or below. Create a routine which limits stress due to
vibration.
A certain amount of noise pollution from this device
cannot be prevented. Shift noisy work to approved
and designated times. If applicable, observe off-times
and limit the working period to the most necessary.
Ear protectors should be worn for your personal
protection and to protect persons nearby.
6 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 6 15.11.13 14:03
Features
Check that all the items are present and that the
product is in perfect condition immediately after
unpacking. Never use the product if it is defective.
1
Housing
2
Transport handle
3
Air hose with quick-disconnect coupler
4
On / Off Switch
5
Hose with valve adapter
6
Pressure gauge
7
Blow-out adapter
8
Tapered universal adapter A
9
Tyre filling device
10
Ball needle
11
Valve adapter
12
Deflating valve adapter
13
Screw-on valve adapter
14
Deflating adapter
15
Additional adapter
16
Tapered universal adapter B
Technical Data
Rated voltage: 220 - 240 V ~ 50 Hz
Power rating: 1.1 kW
Duty type: S3 15 % 10 min
Compressor speed: 3550 rpm
Operating pressure: max. 8 bar
Theo. Suction capacity: 180 l / min
Noise level L
Uncertainty K
Sound power level L
Uncertainty K
: 74.9 dB (A)
pa
: 1.93 dB (A)
pa
: 94.9 dB (A)
wa
: 1.93 dB (A)
wa
Guaranteed
Sound power level: 97 dB (A)
Protection type: IP20
Device weight: approx. 6.0 kg
Measured value
corresponds to: ISO 2151
Noise emission measured according to ISO 2151
Duty type S3-15 %-10 min: S3 = Intermittent duty
without the effect of starting. During a 10 min period the max. operating time is 15 % (1.5 min).
General safety
instructions for air tools
Note: When used in the following text, the terms
„compressed air unit“ or „device“ refer to the compressed air unit specified in these instructions for
use. Basic safety measures must be followed when
using compressed air units to eliminate the risk of
fire, electric shock and personal injury. Be sure to
read and follow the notices within these operating
instructions prior to using the device and store them
in a safe location. The manufacturer assumes no
liability for damages or personal injury resulting
from failure to follow these operating instructions.
This appliance may be used by children age
8 years and up, as well as by persons with reduced physical, sensory or mental capacities,
or lacking experience and / or knowledge, so
long as they are supervised or instructed in the
safe use of the appliance and understand the
associated risks. Children should not be allowed
to play with the device. Cleaning and user
maintenance should not be performed by
children without supervision.
RISK OF INJURY!
During maintenance, switch off the compressed
air supply.
Only use the device in areas of application for
which it was designed!
Do not overburden the device. Never use
hydrogen, oxygen, carbon dioxide or other
bottled gasses to power this tool as doing so
may result in an explosion and thus may cause
severe injuries.
Maintain and clean the device regularly as
instructed (see Chapter „Cleaning / care“).
EXPLOSION HAZARD!
Never use petrol or other flammable liquids to
clean the air tool! Sparks could ignite residual
vapours inside the compressed air unit resulting
in the compressed air unit exploding.
7 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 7 15.11.13 14:03
General safety instructions ... / General safety information for electrical devices
General safety instructions for air tools
Do not use the device in explosive environments
with flammable liquids, gasses or dust.
Never work on materials which are or could
potentially be highly flammable or explosive.
Check the device for damage before startup.
Always make sure that the device is in perfect
condition each time before use.
Always be attentive when working! Unexpected
movement of the device may cause hazards.
Avoid placing your body in an unnatural posi-
tion. Keep proper footing and balance at all
times. By doing this you will be in a better posi-
tion to control the compressed air unit in unfore-
seen circumstances.
Do not use any device if its switch is defective.
A device that can no longer be switched on
and off is dangerous and must be repaired.
Store the device out of the reach of children
when it is not in use.
Do not let anyone use the device if he or she is
not familiar with it or has not read the instructions
and advice. Compressed air units are dangerous
when they are used by inexperienced people.
Maintain the device carefully. Check that moving
device parts are working properly and move
freely. Check for any parts that are broken or
damaged enough to detrimentally affect the
functioning of the device. Have damaged parts
repaired before using the device. Many acci-
dents have their origins in poorly maintained
devices.
Switch the device off if you do not use it any-
more.
Always wear personal protective
equipment and safety glasses. Wearing personal protective equipment
such as dust mask, non-slip safety shoes, safety
helmet or ear protectors, depending on the type
of air tool and its application, reduces the risk
of injuries.
Check the connections and supply lines. All
maintenance devices, couplings and hoses must
be equipped to meet the pressure and air amounts
specified in the device specific values. Pressure
that is too low influences the functioning of the
device; pressure that is too high can cause
damage to property and personal injury.
Protect hoses from kinks, constrictions, solvents
and sharp edges.
Keep hoses away from heat, oil and rotating
parts.
Make sure that the hose clamps are always
tightly fastened. If the hose clamps are not
tightly fastened or are damaged, the air could
escape uncontrollably.
Replace damaged hoses immediately. A dam-
aged supply line may result in the air hose
whipping about and may result in injuries.
If the power cable of the appliance is damaged,
it has to be replaced by the manufacturer or its
service department or a similarly qualified person in order to avoid hazards.
Do not use the device when tired or under the
influence of drugs, alcohol or medications.
One moment of carelessness when using the
device may result in serious injuries.
Do not directly inhale the exhaust air.
Keep exhaust air away from the eyes. Exhaust
air from the air tool may contain water, oil,
metal particles or contaminants from inside the
compressor. This may damage your health.
BE CAREFUL WHEN SET-
TING DOWN THE device! Always put down
the device so it does not come into contact
with the trigger. This could potentially result in
accidental activation of the device, which again
could result in hazards.
Only use suitable accessories. These may be
purchased from the manufacturer. Using non-
OEM accessories may result in hazards.
Only use filtered and regulated compressed air.
Dust, caustic vapours and / or moisture may
damage the motor of the compressed air tool.
The hose must be designed for at least 150 %
of the maximum pressure generated by the
system.
The tool and supply line must be equipped with
a hose coupling to completely release pressure
when disconnecting the coupling hose.
Do not modify this device in any way without
the manufacturer‘s approval.
Only use the device with the specified pressure
(approx. 8 bar max.).
8 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 8 15.11.13 14:03
General safety instructions ... / General safety information for electrical devices
Disconnect the compressed air unit from the air
supply after each use and when not in use. Do
not use the compressed air unit if it leaks or is
in need of repair.
Keep your working area clean and well lit.
Untidy or poorly lit working areas can result in
accidents. Doing so will allow you better control of the device, particularly under unforeseen
circumstances.
Only have the device repaired by qualified
specialist personnel using OEM spare parts.
This will maintain the safety of the device.
Keep children and other persons away from
the device during use. Distractions can cause
you to lose control of the device.
Wear suitable clothing. Do not wear loose
clothing or jewellery. Keep your hair, clothing
and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped
in moving parts.
Put down trigger and device in the event of
unexpected compressor failure.
If possible, use a condensate trap or drain the
hoses and pipes of condensate (water) regularly before and during the use compressed air
units.
ATTENTION! An undersized compressed air
system may minimise the efficiency of your
device.
Never point the compressed air unit at yourself,
other persons or animals. Otherwise there is a
risk of injury.
Always observe all the safety notices attached
to the compressor.
Make sure that the compressor intake opening
is never blocked and the airflow is never hindered.
Switch off the device and pull the plug from the
socket to prevent it from being accidentally
switched on.
Do not allow yourself to become distracted
while working with the device.
Never operate the compressor in temperatures
below 5 degrees.
The outlet must always be within reach.
ATTENTION! The pressure gauge is not cali-
brated! Please check the air pressure with a
calibrated device after filling.
General safety information
for electrical devices
Always connect the device to a residual current
(FI) protective switch.
Protect yourself against electric shock. As you
are working, avoid touching grounded parts
(e.g. refrigerator, water supply pipes etc.).
DANGER OF ELECTRIC SHOCK! Avoid
contact with live lines. This device is not insu-
lated against electric shock.
Regularly check extensions and power supply
cables. Replace any faulty cables with new
ones immediately. If the supply cable of this
device is damaged, it must be replaced by the
manufacturer or its service department, or a
similarly qualified person in order to avoid haz-
ards.
Store the device in a dry environment when it is
not being used over a longer period.
Make sure that the connection cable does not
hang over a corner or be stretched; otherwise
there is a risk of injury.
Do not use the mains lead for any purpose for
which it was not intended, e.g. to carry the
product, to hang it up or to pull the mains plug
out of the mains socket.
Never use power tools in damp or wet environ-
ments, and never expose it to rain or high hu-
midity.
Never switch on the device in the vicinity of
inflammable liquids or gases. If the device is
used outdoors, only use extension cables that
are expressly designed for outdoor use.
Product-specific safety
instructions
CAUTION! HOT SURFACE! The compressor
heats up after extended operation. Therefore
9 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 9 15.11.13 14:03
General safety information for electrical devices / Before use / Start-up
always use the handle on the device to move
it. Never touch the device itself!
ATTENTION! The compressor housing may
become hot during use. Do not touch hot surfaces in order to prevent burns.
Never leave the device in operation unattended.
Built-up heat generated by the device can be a
source of danger. This compressor is equipped
with overheat protection. Of the motor reaches
a temperature of 130 °C, the overheat protection will automatically shut it off. This allows the
motor to cool off, thus preventing damage. Once
the motor has cooled down, it will automatically
restart. This pause is normal and is intended to
protect the motor. This process will repeat if the
motor again reaches a temperature of 130 °C.
Only use indoors.
WARNING! The compressor can start up
without warning!
Before use
Only use the compressor in dry, well ventilated
rooms. The room must be free from dust, acids,
fumes, explosive or flammable gasses.
Check that all of the device‘s parts are in per-
fect condition.
Make sure that the available mains voltage is
compatible with the voltage intended for oper-
ating the compressor.
Avoid long supply lines.
Place the compressor on its rubber feet before
use.
Note: The switch light indicates the mains connection and does not indicate pump operation.
Start-up
Switching the compress
on / off (cf. Fig. A)
Please set the on / off switch 4 to position I to
switch on.
Please set the on / off switch 4 to position 0
to switch on.
Establishing connections
(cf. Fig. B)
ATTENTION! Switch off the device for this
purpose. Please hold on to the coupling to
prevent injuries due to the hose rebounding.
Connect the nipple of your air tool to the com-
pressor‘s air hose
3
.
To disconnect this connection, pull back on the
quick-disconnect coupling of the air hose
Using the tyre filling
3
.
device (cf. Fig. C)
The compressed air tyre filling device 9 is used to
inflate car tyres and, used with the appropriate accessories, also to inflate and control bicycle tyres,
rubber dinghies, air mattresses, balls, etc.
ATTENTION! The pressure gauge
6
is not calibrated! Please check the air pressure with a calibrated device after filling.
Using the blow-out gun
(cf. Fig. D)
The tyre filling device 9 can also be used to clean
hollow spaces and dirty surfaces and tools when
used as a blow-out gun.
To do so, please first remove the hose with
valve adapter
Now attach the blow-out adapter 7 with the
tyre filling device
5
.
9
.
10 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 10 15.11.13 14:03
... / Cleaning / Care / Spare ... / Maintenance and ... /Information about ...
Using the adapter set
The adapter set allows the tyre filling device to be
used for the following additional applications:
a) Inflating balls using the ball needle
b) The valve adapter
inflated.
c) Inflating pools, air mattresses or dinghies using
the additional adapter
d) inflating items with screw valves (e.g. dinghies)
using the screw-on valve adapter
e) Deflating large-volume items. Use the deflating
valve adapter
f) The two tapered universal adapters (
can also be used to inflate air mattresses.
11
allows bicycle tyres to be
15
.
12
for this purpose.
10
.
13
.
8
/ 16)
Cleaning / Care
Note: We recommend cleaning the device imme-
diately after every use. Please first unplug from the
mains before cleaning.
Be sure the device is completely cooled off to
prevent burns.
Do not use cleaning agents or solvents for
cleaning.
Be sure water does not enter the device.
Depressurise the device before cleaning. To do
so, use the tyre filling device as a blow-out gun
and activate the trigger until no air escapes
anymore.
Note: Store the compressor in a dry and safe
environment. Bleed the device and any connected
air tools before storing.
Maintenance and Service
This device requires no maintenance.
Note: Never open the device. Any repairs must
be performed by our authorised service branch or
Customer Service.
Please note the following, if one of the errors below
occurs:
Disconnect the device from any power supply.
Allow the device to cool down and wait a
short period to neutralise residual energy.
Always verify the device is in safe working
condition.
Fault analysis
Fault Solution
1. Compressor
doesn't start
2. Insufficient
working pressure
3. Tools aren't
working
1. Check the mains supply.
Check all cables, the fuse
and outlet are working.
2. Do not use extension cables which are too long.
3. Do not use the device in
ambient temperatures
below + 5 °C.
4. Avoid the motor overheating. Allow the motor to cool
down.
Check seals and the check
valve and have replaced, if
necessary
Check hoses, quick-disconnect coupling and tools, and
have replaced if necessary
Spare parts
Information about warranty
and service processing
Please contact our Service Department directly if
you are in need of spare parts.
www.cmc-creative.de
E-mail:
Phone: +49 (0) 6894 9989752
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 11 15.11.13 14:03
service.gb@cmc-creative.de
Creative Marketing Consulting GmbH
warranty
Dear customer, the warranty for this device is 3 years
from the date of purchase. In the event of product
defects, you have legal rights against the retailer of
this product. Your statutory rights are not limited in
any way by our warranty detailed below.
11 GB
Environmental instructions and disposal information / EC Declaration of Conformity
Information about warranty ... / Environmental instructions and disposal information
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This document is required as your proof of purchase. Should
this device show any fault in materials or manufacture within three years from date of purchase, it will
be repaired or replaced - at our choice - by us free
of charge. This warranty is conditional on the defective device and the receipt of purchase (store
receipt) being presented within the three year warranty period, and that there is a brief written description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, we
will return the repaired device or replacement
thereof. A repair or exchange of the device does
not extend a new warranty period.
Scope of warranty
The appliance has been manufactured to strict
quality guidelines and meticulously examined
before delivery. The warranty applies to faults in
material or manufacture. This warranty does not
apply to product parts subject to normal wear and
tear and which can therefore be considered as wear
items, or to damage to fragile parts, e.g. switches,
storage batteries or glass parts. This warranty
becomes void if the device has been damaged or
improperly used or maintained. All instructions provided in the operating instructions must be followed
strictly to constitute proper use of the product. Purposes and practices which the operating instructions
warn of or advise against must be avoided without
fail. This product is intended for private, non-commercial use only. Any incorrect or improper use of
the device, use of force and changes not performed
by our authorized service branch will void the warranty.
Processing of warranty claims
proof of purchase when making enquiries. The product number can be found on the type plate, an
engraving, the cover page of your instructions (bottom left) or the decal at the back or bottom. In the
event of malfunctions or other defects please first
contact the service department below by phone or
e-mail. A product recorded as defective, along with
the proof of purchase (sales receipt) and a description of the defect and when it occurred, can then
be returned free of charge to you to the service
address provided.
Environmental instructions
and disposal information
Correct disposal of this product Within
the EU this symbol indicates this product
mustn‘t be disposed of with regular
household waste. Used equipment contains previous recyclable materials which should be recycled
to prevent endangering the environment or the health
of humans through unregulated waste management.
Therefore please always dispose of used equipment through suitable collection systems or send
the device to the place of purchase for disposal. It
will then send the device for material recycling.
Don‘t waste,
recycle!
Device, accessories and packaging should be recycled in an environmentally friendly manner. Do not
dispose of the air tool with your household waste,
or throw into fire or water. If possible, non-operational equipment should be recycled. Contact your
local retailer for information.
Notice:
Visit www.lidl-service.com to download
this and many other manuals, product
videos and software.
Please remember the following to ensure your matter
is processed quickly: Please keep your sales receipt
and the item number (e.g. IAN) ready as your
12 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 12 15.11.13 14:03
How to contact us:
Name: C. M. C. GmbH
Internet address: www.cmc-creative.de
E-mail:
service.gb@cmc-creative.de
Phone: +49 (0) 6894 9989752
(standard rates for German landlines)
Registered office: Germany
EC Electromagnetic Compatibility Directive
2004 / 108 / EC
RoHS Directive
2011 / 65 / EC
Pressure Equipment Directive
97 / 23 / EC
IAN 93472
Please note that the following address is not a
service address. Please initially contact the named
Service Centres.
Address:
C. M. C. GmbH
Katharina-Loth-Str. 15
66386 St. Ingbert
Germany
EC Declaration of Conformity
We,
C. M. C. GmbH
Responsible for documentation: Markus Zimmer
Katharina-Loth-Str. 15
66386 St. Ingbert
declare in our sole responsibility that the product
Compressor
Outdoor Directive
2000 / 14 / EC_2005 / 88 / EC
and its amendments. The conformity assessment is
based on the following harmonised standards:
EN 1012-1
EN 60204-1
EN 55014-1
EN 55014-2
EN 61000-3-2
EN 61000-3-3
St. Ingbert, 30. November 2013
Karl Peter Uhle
- Managing Director -
Serial number: 1672
Year of manufacture: 2014/13
IAN: 93472
Model: PKZ 180 A1
meets the basic safety requirements of European
Directives
EC Machinery Directive
2006 / 42 / EC
13 GB
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 13 15.11.13 14:03
14
93472_Kompressor_PKZ_180_A1_content_SI-CZ.indd 14 15.11.13 14:03
Loading...