PUBLICATION ISSUED BY:
Olivetti S.p.A.
Gruppo Telecom Italia
Via Jervis, 77 - 10015 Ivrea (ITALY) www.olivetti.com
Copyright © 2006, Olivetti
All rights reserved
The mark affixed to the product certifies that the product satisfies the basic quality requirements.
The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice.
ENERGY STAR is a U.S. registered mark.
The program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment.
Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product:
•incorrect electrical power supply;
•incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User’s Manual supplied with the product;
•replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel.
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher.
Caution label on the unit
The label () in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using the unit
Follow the cautions below when using this unit.
Warning:
•The fusing area is hot. Exercise care in this area when removing misfed paper.
•Do not look directly at the light source. Doing so may damage your eyes.
•Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15 seconds before turning it back on.
•Unit power must be turned off before installing any supplies.
Caution:
•Place the unit on a firm, level surface.
•Do not install the unit in a humid or dusty location.
•When the unit is not used for a long time, for example for consecutive holidays, turn the power switch off and remove the power cord from the outlet.
•When moving the unit, be sure to turn the power switch off and remove the power cord from the outlet.
•Do not cover the unit with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat radiation, damaging the unit.
•Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
•The socket-outlet shall be installed near the equipment and shall be easily accessible.
Important points when selecting an installation site
Do not install your unit in areas that are:
•damp, humid, or very dusty
•exposed to direct sunlight
•poorly ventilated
•subject to extreme temperature or humidity changes, e.g., near an air conditioner
or heater.
Be sure to allow the required space around the machine for servicing and proper ventilation.
A small amount of ozone is produced within the unit during operation. The emission level is insufficient to cause any health hazard.
Note:
The present recommended long term exposure limit for ozone is 0.1ppm (0.2mg/m3) calculated as an 8hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the unit in a ventilated area.
1
Cautions on handling
Be careful in handling the unit as follows to maintain the performance of this unit.
Do not drop the unit, subject it to shock or strike it against any object. Do not expose the drum cartridge to direct sunlight.
•Doing so will damage the surface (green portion) of the drum cartridge, causing smudges on copies.
Store spare supplies such as drum cartridges and TD cartridges in a dark place without removing from the package before use.
•If they are exposed to direct sunlight, smudges on copies may result.
Do not touch the surface (green portion) of the drum cartridge.
•Doing so will damage the surface of the cartridge, causing smudges on copies.
Cautions on laser
Wave length |
770 nm - 795 nm |
|
11.82 µs/7 mm |
Pulse times |
|
|
|
Output power |
+ |
0.17 mW - 0.01 mW |
Trademark acknowledgements
•Microsoft and Windows are trademarks of Microsoft Corporation in the U.S.A. and other countries.
•IBM and PC/AT are trademarks of International Business Machines Corporation.
•Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
•All other trademarks and copyrights are the property of their respective owners.
As an ENERGY STAR® Partner, OLIVETTI has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Safety precautions:
This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the unit does not produce hazardous laser radiation. For your safety, observe the precautions below.
•Do not remove the cabinet, operation panel or any other covers.
•The unit’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.
In some areas, the "POWER" switch positions are marked "I" and "O" on the copier instead of "ON" and "OFF".
The symbol "O" denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position.
If your copier is so marked, please read "I" for "ON" and "O" for "OFF".
Caution!
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
2
1 INTRODUCTION |
|
USING THE MANUALS................. |
4 |
PART NAMES................................ |
5 |
OPERATION PANEL ..................... |
6 |
2 SETTING UP THE UNIT |
|
SETUP PROCEDURE................... |
7 |
CHECKING PACKED |
|
COMPONENTS AND |
|
ACCESSORIES............................. |
8 |
PREPARING THE UNIT FOR |
|
INSTALLATION.............................. |
8 |
SCAN HEAD LOCKING SWITCH . 9 |
|
INSTALLING THE |
|
TD CARTRIDGE.......................... |
10 |
CONNECTING THE POWER |
|
CORD .......................................... |
12 |
POWER ON................................. |
12 |
3 LOADING PAPER |
|
PAPER ......................................... |
14 |
LOADING THE PAPER TRAY ..... |
15 |
BYPASS FEED |
|
(including special paper).............. |
17 |
5 MAKING COPIES |
|
COPY FLOW ............................... |
46 |
ORIGINAL PLACEMENT............. |
47 |
SET THE COPY QUANTITY ....... |
49 |
EXPOSURE ADJUSTMENT/ |
|
PHOTO COPYING....................... |
50 |
REDUCTION/ENLARGEMENT/ |
|
ZOOM .......................................... |
52 |
6 SPECIAL FUNCTIONS |
|
TWO SIDED COPYING ............... |
53 |
DESCRIPTION OF SPECIAL |
|
FUNCTIONS ................................ |
55 |
TONER SAVE MODE .................. |
55 |
USER PROGRAMS ..................... |
56 |
DISPLAYING TOTAL NUMBER |
|
OF COPIES ................................. |
57 |
7 MAINTENANCE |
|
TD CARTRIDGE |
|
REPLACEMENT .......................... |
58 |
DRUM CARTRIDGE |
|
REPLACEMENT .......................... |
59 |
CLEANING THE UNIT ................. |
60 |
4 INSTALLING THE SOFTWARE |
|
SOFTWARE FOR THE |
|
OLIVETTI PERSONAL MFP |
|
SERIES........................................ |
19 |
HARDWARE AND SOFTWARE |
|
REQUIREMENTS........................ |
19 |
BEFORE INSTALLATION ............ |
20 |
INSTALLING THE SOFTWARE... |
21 |
INDICATORS ON THE |
|
OPERATION PANEL ................... |
31 |
USING THE PRINTER MODE..... |
32 |
USING THE SCANNER MODE........ |
34 |
HOW TO USE THE |
|
ONLINE MANUAL ....................... |
43 |
USING OTHER INSTALLED |
|
DRIVERS..................................... |
44 |
CONNECTING THE INTERFACE |
|
CABLE ......................................... |
45 |
8 TROUBLESHOOTING THE UNIT
TROUBLESHOOTING................. |
62 |
STATUS INDICATORS................. |
63 |
MISFEED REMOVAL................... |
64 |
9 APPENDIX |
|
SPECIFICATIONS ....................... |
69 |
ABOUT SUPPLIES AND |
|
INTERFACE CABLES.................. |
71 |
MOVING AND STORING |
|
THE UNIT .................................... |
72 |
INDEX .......................................... |
73 |
SOFTWARE LICENSE ................ |
76 |
1
2
3
4
5
6
7
8
9
3
This chapter provides basic information for using the unit.
In addition to this printed manual an online manual is also provided. To get full use of all features and functions of this product, be sure to familiarize yourself with both manuals. This printed manual provides all installation and setup instructions as well as instructions in the use of all copier functions. The online manual contains the following information.
Online manual
Provides you with information on how to specify preferences and troubleshooting. Check the online manual when you use this unit after all the initial setup is completed.
How to use the online manual
Explains how to use the online manual.
Provides information on how to print a document.
Scan
Explains how to scan using the scanner driver and how to adjust the settings for the Button Manager.
Troubleshooting
Provides instructions on how to solve driver or software problems.
Conventions used in this manual and online manual
•This operation manual explains the operation of models with and without the SPF. In cases where the operation is the same, the SPF model is used.
•Illustrations of driver screens and other computer screens show the screens that appear in Windows XP Home Edition. Some of the names that appear in these illustrations may differ slightly from the screens that appear in other operating systems.
•This operation manual refers to the Single Pass Feeder as the "SPF".
•In this manual, the following icons are used to provide the user with information pertinent to the use of the unit.
Warns the user that injury may result if the contents of the warning are not properly followed.
Cautions the user that damage to the unit or one of its components may result if the contents of the caution are not properly followed.
Notes provide information relevant to the unit regarding specifications, functions, performance, operation and such, that may be useful to the user.
Indicates a letter displayed in the display.
4
1
1 |
Original table |
10 |
Power switch |
2 |
Operation panel |
11 |
Handle |
3 |
Front cover |
12 |
Power cord socket |
4 |
Paper tray |
13 |
Fusing unit release lever |
5 |
Side cover |
14 |
Transfer charger |
6 |
Side cover open button |
15 |
Charger cleaner |
7Bypass paper guides
8Paper output tray
9Paper output tray extension
5
1 Original to copy key and indicators
Two-sided copies from one-sided originals. Turn on Long Edge or Turn on Short Edge can be selected.
2
Exposure mode selector key and indicators
Use to sequentially select the exposure modes: AUTO, MANUAL or PHOTO. Selected mode is shown by a lit indicator. (p.50)
3Light and dark keys and exposure indicators
Use to adjust the MANUAL or PHOTO exposure level. Selected exposure level is shown by a lit indicator. (p.50) Use to start and terminate user program setting. (p.56)
4Alarm indicators
Drum replacement required indicator (p.59)
Misfeed indicator (p.64)
TD cartridge replacement required indicator (p.58)
5SPF indicator (p.48) (15 cpm model only)
6SPF misfeed indicator (p.67) (15 cpm model only)
7Copy ratio selector key and indicators
Use to sequentially select preset reduction/enlargement copy ratios. Selected copy ratio is shown by a lit indicator. (p.52)
8Copy ratio display (%) key (p.52)
9Display
Displays the specified copy quantity, zoom copy ratio, user program code, and error code.
10SCANNER key and indicator (p.31, p.39)
11ON LINE key and indicator
Lights up when the unit is used as a printer and scanner. For description of the ON LINE indicator, see "INDICATORS ON THE OPERATION PANEL" (p.31).
12Power save indicator
Lights up when the unit is in a power save mode. (p.55, p.56)
13Paper feed location indicators
Light up to show the selected paper feed station.
14Zoom keys and indicator
Use to select any reduction or enlargement copy ratio from 25% to 400% in 1% increments. (p.52)
15Copy quantity keys
•Use to select the desired copy quantity (1 to 99). (p.49)
•Use to make user program entries. (p.56)
16Clear key
•Press to clear the display, or press during a copy run to terminate copying. (p.49)
•Press and hold down during standby to display the total number of copies made to date. (p.57)
17Start key and indicator
•Copying is possible when the indicator is on.
•Press to start copying
•Use to set a user program. (p.56)
6
2 |
SETTING UP THE UNIT |
|
Follow the installation procedure below to use the unit properly.
If the unit does not function properly during setup or use, or if a function cannot be used, see "TROUBLESHOOTING THE UNIT" (p.62).
|
2 |
|
|
SETUP PROCEDURE |
When using the unit for the first time, setup the unit following the procedure shown below.
1Open the package, and make sure that all the accessories are supplied with the unit. (p.8)
2Remove the protective materials. (p.9)
3Install the TD cartridge. (p.10)
4Load the paper in the paper tray (p.15)
5Insert the attached power cord into the power cord socket at the rear of the unit.
6Plug the other end of the power cord into the nearest outlet. (p.12)
7 Install the software.*1 (p.19)
8 Connect the interface cable*1 (p.45) and turn on the unit. (p.12)
9Now, you can copy (p.46), print (p.32), or scan (p.34) your document.
*1 If you are only using the unit for copying, skip this step.
7
Open the carton and check if the following components and accessories are included.
If anything is not included or is damaged, contact your authorized Service representative.
Power cord
1 Be sure to hold the handles on both sides of the unit to unpack the unit and carry it to the installation location.
8
2 Remove all pieces of tape shown in the illustration below. Then open the original cover/SPF and remove protective materials. After that, take out the bag containing the power cord and TD cartridge.
2
12 cpm model |
15 cpm model |
|
12 cpm model |
15 cpm model |
The scan head locking switch is under the original table. If the switch is locked ( ), the unit will not operate. Unlock the switch ( ) as shown below.
9
1 Open the side cover.
2 Push gently on both sides of the front cover to open the cover.
3 Remove the TD cartridge from the bag. Hold the cartridge on both sides and shake it horizontally four or five times. Hold the tab of the protective cover and pull the tab to your side to remove the cover.
4 or 5 times
4 Gently insert the TD cartridge until it locks in place while pushing the lock release button.
10
5 Close the front cover and then |
|
the side cover by pressing the |
|
round projections near the |
|
side cover open button. |
|
When closing the covers, be |
|
sure to close the front cover |
|
securely and then close the |
2 |
side cover. If the covers are |
|
closed in the wrong order, the |
|
covers may be damaged. |
11
|
If you use the unit in a country other than the country where the unit was |
|
purchased, you will need to make sure that your local power supply is |
|
compatible with your model. If you plug the unit into an incompatible |
|
power supply, irreparable damage to the unit will result. |
1 |
Ensure that the power switch of |
|
the unit is in the OFF position. |
|
Insert the attached power cord |
|
into the power cord socket at the |
|
rear of the unit. |
2 |
Plug the other end of the power cord into the nearest outlet. |
|
Only insert the power cord into a properly grounded wall socket. |
|
Do not use extension cords or power strips. |
Power on
Ensure that the power switch of the unit is in the OFF position. Plug the other end of the power cord into the nearest outlet. Turn the power switch on the left side of the unit to the "ON" position. The start ( ) indicator will light up and other indicators which show the initial settings of the operation panel will also light up to indicate the ready condition. For the initial settings, see the "Initial settings of operation panel" described on the next page.
• The unit will enter a power save mode once the set time has elapsed without any unit operation . The settings of the power save modes can be modified. See "USER PROGRAMS" (p.56).
•The unit will return to the initial settings a preset amount of time after the end of copy, or scanner job. The preset amount of time (auto clear time) can be changed. See "USER PROGRAMS" (p.56).
12
About the scan head
The scan head lamp remains on constantly when the unit is in the ready condition (when the Start indicator is illuminated).
The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate unit trouble.
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when
the time set with the "Auto clear time" setting (p.55) elapses after a copy or scanner 2 job is finished, or when the clear () key is pressed twice.
The initial settings of the operation panel are shown below.
"0" is displayed in the display
When copying is begun in this state, the settings in the following table are used.
Copy quantity |
1 copy |
Exposure adjustment |
Auto |
Zoom |
100% |
If not used for a certain period of time, the unit will automatically enter auto power shut-off mode (p.55) in order to minimize power consumption. In cases where the machine will not be used for a long time, turn off the power switch and remove the power cord from the outlet.
13
3 |
LOADING PAPER |
|
Follow the steps below to load paper into the tray.
For best results, use only paper recommended by OLIVETTI.
Type of paper |
Type of media |
Size |
Weight |
|
feeding |
|
|
|
|
|
|
|
|
|
Paper tray |
Standard paper |
A4 |
56 to 80g/m2 |
|
|
|
|
B5 |
|
|
|
|
A5 |
|
|
|
|
Letter |
|
|
|
|
Legal |
|
|
|
|
Invoice |
|
|
|
|
|
|
Single bypass |
Standard paper and |
A4 |
52 to 128g/m2** |
|
|
thick paper |
B5 |
|
|
|
|
|
A5 |
|
|
|
|
B6 |
|
|
|
|
A6 |
|
|
|
|
Letter |
|
|
|
|
Legal |
|
|
|
|
Invoice |
|
|
|
|
|
|
|
Special |
Transparency |
A4 |
|
|
media |
film |
Letter |
|
|
|
|
|
|
|
|
Envelope* |
International DL |
|
|
|
|
International C5 |
|
|
|
|
Commercial 10 |
|
|
|
|
Monarch |
|
|
|
|
|
|
*Do not use non-standard envelopes, and envelopes that have metal clasps, plastic snappers, string closures, windows, linings, self-adhesive, patches or synthetic materials. Do not use envelopes that are filled with air or envelopes that have labels or stamps attached. These will cause physical damage to the unit.
**For paper weighing from 104 to 128g/m2, A4 is the maximum size that can be fed through the single bypass.
•Special papers such as transparency film, labels and envelope must be fed one sheet at a time through the single bypass.
14
1 Raise the handle of the paper tray and pull the paper tray out until it stops.
2 Remove the pressure plate lock. Rotate the pressure plate lock in the direction of the arrow to remove it while pressing down the pressure plate of the paper tray.
3
3 Store the pressure plate lock which has been removed in step 2. To store the pressure plate lock, rotate the lock to fix it on the relevant location.
Pressure plate lock
4 Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the lever of paper guide A and slide the guide to match with the width of the paper. Move paper guide B to the appropriate slot as marked on the tray.
15
5 Fan the paper and insert it into the tray. Make sure the edges go under the corner hooks.
Do not load paper above the maximum height line ( ). Exceeding the line will cause a paper misfeed.
6 Gently push the paper tray back into the unit.
• After loading paper, to cancel the blinking without restarting copying, press the clear () key. The in the display will go out and the start () indicator will light up.
•Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges.
•Make sure all the paper in the stack is the same size and type.
•When loading paper, ensure there is no space between the paper and the guide, and check if the guide is not set too narrow causing the paper to bend. Loading paper in these ways will result in document skew or a paper jam.
•When not using the unit for an extended period, remove all paper from the paper tray and store it in a dry place. If paper is left in the unit for an extended period, the paper will absorb moisture from the air, resulting in paper jams.
•When adding new paper to the paper tray, remove the old paper already contained in the tray. Placing new paper on top of the paper already contained in the tray may result in feeding two sheets at one time.
16
The single bypass can be used to feed standard paper, transparency film, labels, envelopes, and other special purpose paper. Paper measuring from A6 to A4/Legal and in the weight range of 52 to 128g/m2 can be used in this tray. (For paper weighing from 104 to 128g/m2, A4 is the maximum size.)
• The single bypass can hold one sheet of paper.
• The original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.
The single bypass
• If you insert a sheet of paper into the single bypass when multiple |
3 |
copies have been set with the copy quantity setting (p.49), the copy |
quantity setting will change to "0" and only one copy will be made.
•When copying onto transparency film, remove each copy promptly. Do not let copies stack up.
1Select copy and print settings before you begin the copy job.
For information on the copy settings, see "MAKING COPIES" (p.46). For information on the print settings, see the online manual or the Help file for the printer driver, and then begin printing from the single bypass.
2Set the paper guides to the paper width. Insert a single sheet of copy or print paper (print face down) into the feed slot of the single bypass.
Using copy mode
When you insert the paper, the machine will automatically draw in the paper and begin copying.
Using printer mode
After appears in the display, wait until the Paper feed location indicator for the single bypass illuminates and insert the paper. The machine will automatically draw in the paper and begin printing.
Print face
17
Note for loading envelopes
•Envelopes must be fed narrow side into the feed slot one sheet at a time.
•Do not use non-standard envelopes, and envelopes that have metal clasps, plastic snappers, string closures, windows, linings, self-adhesive, patches or synthetic materials. Do not use envelopes that are filled with air or envelopes that have labels or stamps attached.
•Envelopes of which the surface is not flat because of embossing may cause the prints to become smudged.
•Under high humidity and temperature conditions the glue flaps on some envelopes may become sticky and be sealed closed when printed.
•Use only envelopes which are flat and crisply folded. Curled or poorly formed envelopes may be poorly printed or may cause misfeeds.
•Be sure to select either Com10, DL, C5 or Monarch on the paper size setting of the printer driver. (For detailed information on printer driver, refer to the online manual.)
•It is recommended that you perform a test print before performing the actual print job.
18
4 |
INSTALLING THE SOFTWARE |
|
This chapter provides you with information on how to install required software to use this unit with your computer. Information on how to use the online manual is also provided. The following term is used in this chapter.
CD-ROM
Means the supplied CD-ROM with the OLIVETTI Personal MFP Series software.
The supplied CD-ROM includes software for this unit.
MFP driver
Scanner driver
Permits you to operate scanning function of this unit with TWAIN-compliant and WIA-compliant application.
Printer driver
Enables you to use the printer function of this unit with your computer.
Print Status Window
The print state and information on current printing are displayed on the status monitor window.
Desktop Document Manager
An integrated software environment that makes it easy to manage document and image files and launch applications.
Button Manager
Button Manager enabling the SCANNER ( ) key located on the unit.
The scanning feature is only available with Windows 98/Me/2000/XP using a USB connection. For users running Windows 95/NT 4.0 or using a parallel connection, only printing is available.
Check the following hardware and software requirements in order to install the software.
Computer type |
IBM PC/AT or compatible computer equipped with a |
|
USB1.1*1 or bi-directional parallel interface (IEEE 1284) |
Operating system*2 |
Windows 95, Windows 98, Windows Me, Windows NT |
|
Workstation 4.0 (ServicePack 5 or later)*3, Windows 2000 |
|
Professional*3, Windows XP Professional*3, Windows XP |
|
Home Edition*3 |
Display |
800 x 600dots (SVGA) display with 256 colors (or better) |
Hard disk free space |
150MB or more |
Other requirement |
An environment on which any of the operating systems listed |
for hardware |
above can fully operate |
|
|
*1 Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled model with USB interface equipped as standard.
*2 Printing is unavailable in MS-DOS mode.
*3 The administrator's authorization is required to install this software using this installer.
4
19
The following table shows the drivers and software that can be installed for each version of Windows and interface connection method.
|
MFP Driver |
|
Desktop |
|
|
Printer driver/ |
|
Button |
|
|
|
Document |
||
|
Print Status |
Scanner driver |
Manager |
|
|
Manager |
|||
|
Window |
|
|
|
|
|
|
|
|
Users of Windows |
|
|
|
|
98/Me/2000/XP who |
|
Available |
Available |
Available |
will use the USB |
|
|||
|
|
|
|
|
interface connection |
|
|
|
|
|
|
|
|
|
Users of Windows |
Available*1 |
|
|
|
98/Me/2000/XP who |
|
|
|
|
|
|
|
|
|
will use the parallel |
|
Not Available |
Not |
Available*2 |
interface connection |
|
Available |
||
|
|
|
||
|
|
|
|
|
Windows 95/NT 4.0 |
|
|
|
|
users |
|
|
|
|
|
|
|
|
|
*1 When the unit is connected through the parallel port, the Print Status Window can only be used when the parallel port is set to ECP mode. To set the parallel port mode, refer to your computer manual or ask the manufacturer of your computer.
*2 Desktop Document Manager can be installed when using a parallel interface connection, however, the unit’s scanner function cannot be used.
Is there another GDI printer driver or a Windows Printing System printer driver already installed? If installed, change the printer port setting. For the change of the printer port setting, see "USING OTHER INSTALLED DRIVERS" (p.44).
Flow of installation
Refer to the following table and then begin installation
Operating |
Interface |
Reference pages for how to install |
|
system |
|||
|
|
||
|
|
|
|
Windows XP |
USB/ |
Installing onto Windows XP (USB/parallel interface) |
|
Parallel |
(p.21) |
||
|
|||
|
|
|
|
|
USB |
Installing onto Windows 98/Me/2000 (USB interface) (p.25) |
|
Windows 98 |
|
|
|
Parallel |
Installing onto Windows 95/98/Me/NT4.0/2000 |
||
|
(Parallel interface) (p.28) |
||
|
|
||
|
|
|
|
|
USB |
Installing onto Windows 98/Me/2000 (USB interface) (p.25) |
|
Windows Me |
|
|
|
Parallel |
Installing onto Windows 95/98/Me/NT4.0/2000 |
||
|
(Parallel interface) (p.28) |
||
|
|
||
|
|
|
|
|
USB |
Installing onto Windows 98/Me/2000 (USB interface) (p.25) |
|
Windows 2000 |
|
|
|
Parallel |
Installing onto Windows 95/98/Me/NT4.0/2000 |
||
|
(Parallel interface) (p.28) |
||
|
|
||
|
|
|
|
Windows 95/ |
Parallel |
Installing onto Windows 95/98/Me/NT4.0/2000 |
|
NT 4.0 |
(Parallel interface) (p.28) |
||
|
|||
|
|
|
20
The following term is used in this section.
MFP
Means the unit as a printer and scanner.
• For this description, it is assumed that the mouse is configured for right hand operation.
• To print or scan, the MFP must be in the online state.
•The scanner feature only works when using a USB interface cable.
•If any error message appears, solve the problem following the instructions on the screen. After your problem is solved, the installing procedure will be continued. Depending on your problem, you may have to exit the installer. In this case, click the "Cancel" button to exit the installer. After solving your problem, reinstall the software from the beginning.
Installing onto Windows XP (USB/parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not |
4 |
|
|
connected to the MFP. |
|
1
2
Insert the supplied CD-ROM into your CD-ROM drive.
Click the "start" button, click "My Computer" ( ), and then double-click the CD-ROM ( ) icon.
When any of "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button.
3 Double-click the "Setup" ( ) icon.
If the language selection screen appears after you double click the "Setup" icon, select the language you wish to use and click the "Next" button. (Normally, the correct language is selected automatically.)
4 Select the software packages to be installed, and then click the "Next" button.
The software packages with checkmark ( ) on the list on the screen will be installed.
Click the "Display README" button to show the information on the selected package.
Desktop Document Manager
21
•If you are using the parallel interface connection, do not select the Button Manager checkbox because this feature is not supported with the parallel interface.
•If the following screen appears, click the "OK" button. Review the contents in "BEFORE INSTALLATION" (p.20), and then select only appropriate the software packages to be installed.
5 Review the software packages to be installed on the screen, and then click the "Start" button.
The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select appropriate packages again.
Desktop Document Manager
6 Copying files for MFP driver installation (This step will start if it was selected in step 4).
1After confirming the message in the "Welcome" window, click the "Next" button.
2A dialog box appears asking you to verify that the USB or parallel interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button.
3Click the "Next" button in the dialog box to install the MFP driver or Cancel to quit the installation.
The setup program will start to copy the files.
If the following screen appears while the files are being copied (the message may appear more than once), click "Continue Anyway".
4When the "The MFP driver installation is complete." dialog box appears, click the "OK" button.
The Button Manager installer will start.
22
7 Begin installation of the Button Manager (This step will start if it was selected in step 4).
1After confirming the message in the "Welcome" window, click the "Next" button.
2Read the message in the "Please read the following information." window, and then click the "Next" button.
3When a message appears that lets you specify the location for the software to be installed, click the "Next" button.
4If the program displays "Do you want the Button Manager added to Windows Startup?", check "Yes" and click the "OK" button.
The setup program will start to copy the files.
5Click the "Finish" button when the message informs you that setup is successful.
The Desktop Document Manager installer will start.
8 Begin installation of the Desktop Document Manager (This step will start if it was selected in step 4).
1 |
After confirming the message in the "Welcome to Desktop |
4 |
2 |
Document Manager installation" window, click the "Next" button. |
|
Read the message in the "Information" window, and then click the |
||
|
"Next" button. |
3When the "Choose Destination Location" window appears, click the "Next" button.
4When the "Select Program Folder" window appears, click the "Next" button.
5Click the "Finish" button when the message informs you that Setup is complete.
9 Click the "Close" button when the message informs you that "Setup has finished". When the "Now connect the MFP interface cable to the PC" dialog box appears, click the "OK" button.
After the installation, a message to restart your computer may be displayed. In this case, click the "Yes" button to restart your computer.
Desktop Document Manager
23