Kenwood DNX 7260 BT Installation Guide

0 (0)

GPS NAVIGATION SYSTEM

SYSTÈME DE NAVIGATION GPS

GPS-NAVIGATIONSSYSTEM

GPS-NAVIGATIESYSTEEM

SISTEMA DI NAVIGAZIONE GPS

SISTEMA DE NAVEGACIÓN GPS

SISTEMA DE NAVEGAÇÃO GPS

DNX SERIES

DNX7260BT

INSTALLATION MANUAL MANUEL D'INSTALLATION INSTALLATION-HANDBUCH INSTALLATIEHANDLEIDING MANUALE DI INSTALLAZIONE MANUAL DE INSTALACIÓN MANUAL DE INSTALAÇÃO

Accessories

..........1

..........2

..........1

Installation Procedure

1.To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery.

2.Make the proper input and output wire connections for each unit.

3.Connect the wire on the wiring harness.

4.Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle.

5.Take Connector A on the wiring harness and connect it to the external power connector on your vehicle.

6.Connect the wiring harness connector to the unit.

7.Install the unit in your car.

8.Reconnect the - terminal of the battery.

9.Press the reset button.

10.Perform the Initial Setup. (Refer to the Instruction Manual.)

2WARNING

•If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

•Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.

Acquiring GPS Signals

The first time you turn on this unit, you must wait while the system acquires satellite signals for the first time. This process could take up to several minutes. Make sure your

vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter.

About the Front Panel

When removing the product from the box or installing it, the front panel may be

positioned at the angle shown in (Fig. 1). This

2 DNX SERIES

is due to the characteristics of a mechanism the product is equipped with.

If the program that is activated when the product is first powered on works properly, the front panel will automatically move into the position (initial setting angle) shown in (Fig. 2).

(Fig. 1)

(Fig. 2)

After the Installation

After the installation, perform the Initial Setup by referring to the instruction manual.

•Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.

•Make sure to ground the unit to a negative 12V DC power supply.

•Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

•Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.

•If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.

•If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

•If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.

•If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.

•Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

•Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.

•When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal.

•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

•Mount the unit so that the mounting angle is 30° or less.

•This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.

•Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result.

•Reception may drop if there are metal objects near the Bluetooth antenna.

Bluetooth antenna unit

¤CAUTION

Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.

English 3

Connection

Connector A

				Ground wire (Black)
8	6	4	2	Battery wire (Yellow)

7	5	3	1	Ignition wire (Red)	FM/AM antenna
8	6	4	2	Antenna Cord
					input (JASO)
7	5	3	1

Connector B

(Orange/White)	Dimmer control wire (Orange/White)
	ILLUMI

⁄Connect to the vehicle's parking brake detection switch harness.

Parking sensor wire (Light Green)

PRK SW	For the sake of safety, be sure to connect the parking sensor.

Connect to vehicle's reverse lamp harness when using the optional rear view camera.

To steering remote

⁄To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on.

Connect to the terminal that is grounded when either the telephone rings or during conversation.

⁄To connect the Kenwood navigation system, consult your navigation manual.

Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle.

⁄ If no connections are made, do not let the cable come out from the tab.

4 DNX SERIES

+ 8 hidden pages