00CP-S420/CP-X430 03.9.2 0:08 PM 2
www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 Sales@touchboards.com
Liquid Crystal Projector
CP-S420/CP-X430
CP-S420WA/CP-X430WA/CP-X430W
USER'S MANUAL
Please read this user's manual thoroughly to ensure correct usage through understanding.
BEDIENUNGSANLEITUNG
Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung aufmerksam.
MANUEL D'UTILISATION
Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil.
MANUALE D'ISTRUZIONI
Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.
MANUAL DE USUARIO
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto.
GEBRUIKSAANWIJIZING
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de uitgebreide mogelijkheden.
BRUKERHÅNDBOK
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
INSTRUÇÕES DO PROPRIETÁRIO
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do usuário.
TECHNICAL
REGULATORY NOTICES
TECHNICAL PORTGÊS NORSK NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH
www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273
Sales@touchboards.com
01CP-S420/CP-X430 03.9.2 0:08 PM 1
Liquid Crystal Projector
USER'S MANUAL
Thank you for purchasing this liquid crystal projector.
WARNING • Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
•The manufacturer assumes no responsibility for any errors that may appear in this manual
•The reproduction, transmission or use of this document or contents is not permitted without express written authority.
TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned.
CONTENTS
|
Page |
|
Page |
|
FEATURES ....................................... |
2 |
TROUBLESHOOTING .................... |
20 |
|
BEFORE USE ................................... |
2 |
OSD Message ...................................... |
20 |
|
Contents of Package .............................. |
2 |
Indicators Message .............................. |
21 |
|
Part Names............................................. |
3 |
Symptom .............................................. |
22 |
|
Loading the Batteries.............................. |
5 |
SPECIFICATIONS........................... |
23 |
|
INSTALLATION ................................ |
6 |
WARRANTY AND AFTER-SERVICE...... |
24 |
|
Installation of the Projector and Screen........ |
6 |
....................................................................................... |
||
Angle Adjustment |
6 |
|||
TABLES |
|
|||
Cabling |
7 |
|
||
Table 1. Installation Reference |
6 |
|||
Power Connection |
8 |
|||
Table 2. Cabling |
7 |
|||
Example of System Setup |
8 |
|||
Table 3. Basic Operation |
10 |
|||
Plug & Play |
8 |
|||
Table 4. Setup Menu |
12 |
|||
OPERATIONS |
9 |
|||
Table 5. Input Menu |
13 |
|||
Power ON |
9 |
|||
Table 6. Image Menu |
14 |
|||
Power OFF |
9 |
|||
Table 7. Options Menu |
15 |
|||
Basic Operation |
10 |
|||
Table 8. No Signal Menu |
16 |
|||
Setup Menu |
12 |
|||
Table 9. OSD Message |
20 |
|||
Input Menu |
13 |
|||
Table 10. Indicators Message |
21 |
|||
Image Menu |
14 |
|||
Table 11. Symptom |
22 |
|||
Options Menu |
15 |
|||
Table 12. Specifications |
23 |
|||
No Signal Menu |
16 |
|||
|
|
|||
MAINTENANCE .............................. |
17 |
....................................................................................... |
|
|
Lamp..................................................... |
17 |
For "TECHNICAL" and "REGULATORY |
||
Air Filter ................................................ |
19 |
NOTICE", see the end of this manual. |
|
|
Other Maintenance ............................... |
19 |
|
|
ENGLISH
ENGLISH-1
01CP-S420/CP-X430 03.9.2 0:08 PM 2
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.
Outstanding Brightness
The UHB lamp and high-efficiency optical system assure a high level of brightness.
Partial Magnification Function
Interesting parts of images can be magnified for closer viewing.
Distortion Correction Function
Distortion-free images are quickly available.
Extra-low Noise Function
Acoustic noise level from the unit can be reduced.
BEFORE USE
Contents of Package
Make sure all of the following items are included in the package. If anything is missing, please contact your dealer.
WARNING • Keep the original packing material for future reshipment. To avoid penetration of foreign objects, do not put the projector into a case or
bag together with anything except the accessories of the projector, signal cables and connectors.
Power Cord |
Power Cord |
Power Cord |
(US Type) |
(UK Type) |
(Europe Type) |
Projector
(with Lens Cap)
CP-S420/CP-X430 |
USER'S MANUAL |
BEDIENUNGSANLEITUNG |
MANUEL D'UTILISATION |
MANUALE D'ISTRUZIONI |
MANUAL DE USUARIO |
GEBRUIKSAANWIJIZING |
BRUKERHÅNDBOK |
INSTRUÇÕES DO PROPRIETÁRIO |
TECHNICAL |
REGULATORY NOTICES |
RGB Cable |
Component |
Mouse cable |
|
Video Cable |
(PS/2) |
User’s Manual
(this manual)
Safety Instructions
STANDBY/ON BLANK
LASER
VIDEO |
RGB |
Batteries
for Remote Control Transmitter
AUTO |
|
MENU |
KEYSTONE |
MENU SELECT |
|
POSITION |
RESET |
FREEZE PinP
MAGNIFY MUTE OFF
VOLUME
Soft case |
Remote Control |
Transmitter |
ENGLISH-2
01CP-S420/CP-X430 03.9.2 0:08 PM 3
BEFORE USE (continued)
Part Names
Speaker
|
Zoom Knob |
Carrying Handle |
Focus Ring |
|
Remote Control Sensor
|
Lens |
|
AC Inlet |
Foot Adjuster |
|
|
||
(to the Power Cord) |
|
|
Power Switch |
Lens Cap |
|
Foot Adjuster |
|
|
Ventilation Openings |
FRONT/LEFT VIEW OF |
|
(Intake) |
||
THE PROJECTOR |
||
|
||
Control Panel (Refer to P.9 "OPERATIONS") |
||
STANDBY/ON Button |
INPUT Button |
|
KEYSTONE Button |
LAMP Indicator |
|
|
TEMP Indicator |
|
|
POWER Indicator |
|
Foot Adjuster Button |
RESET Button |
|
|
MENU Button |
Filter Cover
(Air Filter and Intake )
for the Cooling Fan Ventilation Openings
(exhaust)
REAR/RIGHT VIEW OF |
Terminal Panel |
THE PROJECTOR |
(Refer below) |
S-VIDEO Terminal |
Remote Control Sensor |
|
COMPONENT VIDEO
Y Terminal
CB/PB Terminal
CR/PR Terminal
VIDEO IN Terminal
AUDIO IN R Terminal
AUDIO IN L Terminal
AUDIO IN 1 Terminal
AUDIO IN 2 Terminal
AUDIO OUT Terminal
COMPONENT VIDEO |
|
DVI |
|
CR/PR CB/PB |
Y |
|
|
|
1 |
RGB IN |
2 |
|
|
|
|
S-VIDEO IN |
AUDIO |
R |
L |
VIDEO IN |
|
IN |
|
|
|
|
AUDIO 1 |
2 |
AUDIO OUT |
USB |
|
IN |
|
|
|
|
RGB OUT |
CONTROL |
TERMINAL PANEL
DVI Terminal (CP-X430 only)
RGB IN 1 Terminal
RGB IN 2 Terminal
CONTROL Terminal
RGB OUT Terminal
USB Terminal
ENGLISH
ENGLISH-3
01CP-S420/CP-X430 03.9.2 0:08 PM 4
BEFORE USE (continued)
Part Names (continued)
STANDBY/ON Button
VIDEO Button
Disk Pad
Used to operate the mouse shift function and left click function.
AUTO Button
|
BLANK |
STANDBY/ON |
LASER |
|
|
|
RGB |
VIDEO |
BLANK Button
LASER Button
RGB Button
MOUSE / RIGHT Button
Used to click the right mouse button.
KEYSTONE Button
MENU Button
MENU SELECT Button
Used to click the left mouse button.
,,, Button
Used to operate the mouse shift function.
POSITION Button
AUTO |
KEYSTONE |
|
|
||
MENU |
|
|
MENU |
SELECT |
|
RESET |
||
|
||
POSITION |
PinP |
|
|
FREEZE |
MUTE
MAGNIFY |
OFF |
VOLUME
RESET Button
Used to click the right mouse button.
PinP Button
FREEZE Button
MUTE Button
VOLUME Button
MAGNIFY Button |
REMOTE CONTROL |
|
TRANSMITTER |
||
|
||
|
(Refer to P.9 "OPERATIONS") |
These functions work when the mouse control function is activated. Remember, the POSITION, BLANK ON and MENU ON functions disable the mouse control function.
WARNING • The laser pointer of the remote control transmitter is used in
place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems.
CAUTION • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
AVOID EXPOSURE-
LASER RADIATIONS IS
EMITTED FROM THIS
APERTURE
C A U T I O N
LASER RADIATION-
DO NOT STARE INTO BEAM
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
CLASS2 LASER PRODUCT
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS2 LASER PRODUCT
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
IEC60825-1 : 1993+A1:1997
Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to Laser Notice No.50, dated 2001.7.26
SMK CORPORATION
6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511 MANUFACTURED Novemver 2001
PLACE OF MANUFACTURER: A
NOTE • Keep the remote control transmitter away from children and pets.
•Do not give the remote control transmitter any physical impact. Take care not to drop.
•Do not place the heavy objects on the remote control transmitter.
•Do not wet the remote control transmitter or place it on any wet object.
•Do not place the remote control transmitter close to the cooling fan of the projector.
•Do not disassemble the remote control transmitter.
ENGLISH-4
01CP-S420/CP-X430 03.9.2 0:08 PM 5
BEFORE USE (continued)
Loading the Batteries
Install the AA batteries into the remote control
transmitter. |
|
|
|
1. |
Remove the battery cover. |
|
|
|
Push the knob while lifting up the battery cover. |
|
|
2. |
Load the batteries. |
|
|
|
Make sure the plus and minus poles are correctly |
1 |
2 |
|
oriented. |
||
|
|
|
|
3. |
Close the battery cover. |
|
|
CAUTION • Use only the specified batteries with this remote control transmitter. Also, do not mix new and old batteries. This could cause battery
cracking or leakage, which could result in fire or personal injury.
•When loading the batteries, make sure the plus and minus terminals are correctly oriented as indicated in the remote control transmitter. Incorrect orientation could cause battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment.
•When you dispose the battery, you should obey the law in the relative area or country.
•Keep the battery away from children and pets.
•When not to be used for an extended period, remove the batteries from the remote control transmitter.
NOTE Replace the batteries when remote control transmitter operation becomes difficult.
ENGLISH
ENGLISH-5
01CP-S420/CP-X430 03.9.2 0:08 PM 6
INSTALLATION
Installation of the Projector and Screen
Refer to the drawing and table below for determining the screen size and projection distance.
The projection distances shown in the table below are for full size (CP-S420:800 x 600 pixels , CP-X430:1024 x 768 pixels). a: Distance from the projector to the screen. (±10%)
Table 1. Installation Reference |
|
|
|
|
|||
Screen size |
|
a [inches (m)] |
|
|
|
||
[inches (m)] |
Min. |
Max. |
|
Top View |
|||
40 |
(1.0) |
62 |
(1.6) |
82 |
(2.1) |
|
|
60 |
(1.5) |
94 |
(2.4) |
123 |
(3.1) |
|
|
80 |
(2.0) |
127 |
(3.2) |
164 |
(4.2) |
|
|
100 |
(2.5) |
160 |
(4.1) |
205 |
(5.2) |
|
|
120 |
(3.0) |
192 |
(4.9) |
246 |
(6.3) |
|
|
150 |
(3.8) |
241 |
(6.1) |
308 |
(7.8) |
|
|
200 |
(5.0) |
323 |
(8.2) |
411 (10.4) |
a |
Side View |
|
|
|
|
|
|
|
CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.
• When you fix this unit with a metal tool and the like, you must connect it with ground wire; otherwise, fire or electric shock can result.
Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the building using an optional three-core power-supply cord.
•Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and cause damage. Be especially careful not to install it with ventilation holes blocked.
•Do not install LCD projector in smoke effected environment. Smoke residue may buildup on critical parts (i.e.LCD panel, Lens Assy etc.).
Angle Adjustment
Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 9˚ approximately.
Foot Adjusters |
Press the foot |
|
adjuster button |
||
|
1.Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle.
2.Release the button to lock at the desired angle.
3.Use the foot adjusters for fine adjustment. Do not force the adjuster screws. This could damage the adjusters or cause the lock to fail.
CAUTION • Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or fingers could get caught and cause personal
injury.
ENGLISH-6
01CP-S420/CP-X430 03.9.2 0:08 PM 7
INSTALLATION (continued)
Cabling
Refer to the table below for connecting each terminal of the projector to a device.
Table 2. Cabling
Function |
Terminal |
Cable |
|
|
|
|
|
RGB input |
RGB IN 1 |
|
|
|
RGB cable with D-sub 15-pin shrink jack |
||
RGB IN 2 |
|||
|
|||
|
and inch thread screws |
||
|
|
||
RGB output |
RGB OUT |
|
|
|
|
|
|
DVI input (CP-X430 only) |
DVI |
DVI cable with inch thread screws |
|
|
|
|
|
|
AUDIO IN 1 |
|
|
Audio input |
(interlocked with RGB IN 1 or DVI) |
Audio cable with stereo mini jack |
|
|
|||
(from the computer) |
AUDIO IN 2 |
||
|
|||
|
|
||
|
(interlocked with RGB IN 2) |
|
|
|
|
|
|
PS/2 mouse control |
|
PS/2 mouse cable |
|
|
|
|
|
ADB mouse control |
CONTROL |
ADB mouse cable |
|
|
|
||
Serial mouse control |
Serial mouse cable |
||
|
|||
|
|
|
|
RS-232C communication |
|
RS-232C cable |
|
|
|
|
|
USB mouse control |
USB |
USB cable |
|
|
|
|
|
S-video input |
S-VIDEO IN |
S-video cable with mini DIN 4-pin jack |
|
|
|
|
|
Video input |
VIDEO IN |
Video/Audio cable |
|
|
|
|
|
|
COMPONENT VIDEO Y |
|
|
|
|
|
|
Component video input |
COMPONENT VIDEO CB/PB |
Component Video cable |
|
|
|
|
|
|
COMPONENT VIDEO CR/PR |
|
|
|
|
|
|
Audio input |
AUDIO IN L |
Video/Audio cable |
|
|
|||
(from video equipment) |
AUDIO IN R |
or Audio cable with RCA jack |
|
|
|
|
|
Audio output |
AUDIO OUT |
Audio cable with stereo mini jack |
|
|
|
|
ENGLISH
CAUTION • Incorrect connecting could result in fire or electrical shock. Please read this manual and the separate “SAFETY INSTRUCTIONS”.
•Before connecting, turn off to all devices to be connected, except for the USB cable.
•The cables may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified.
NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the projector is compatible with the device.
•Secure the screws on the connectors and tighten.
•For some RGB input modes, the optional Mac adapter is necessary.
•To select the DVI input, the comuter may need some settings. See the manuals of the computer for details.
•Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.
•Refer to the “TECHNICAL” section for the pin assignment of connectors and RS-232C communication data.
•When the DVI terminal is used, the RGB OUT terminal may not function.
ENGLISH-7
01CP-S420/CP-X430 03.9.2 0:08 PM 8
INSTALLATION (continued)
Power Connection
Use the correct power cord depending on the power outlet to be used.
Connect the AC inlet of the projector to the power outlet firmly by the power cord.
CAUTION • Be carful in handling the power cord according to instructions of the
accompanying manual "SAFETY INSTRUCTIONS" and this manual.
• Connect the power cord firmly. Avoid using a loose, unsound outlet or failed contact.
Power
outlet
Power Cord |
AC Inlet |
Example of System Setup
Display
Monitor
COMPONENT VIDEO |
|
|
||
CR/PR |
CB/PB |
Y |
|
DVI |
DVD Player |
|
|
|
|
|
1 |
RGB IN |
2 |
|
|
|
|
S-VIDEO IN |
|
AUDIO R |
L VIDEO IN |
|
IN |
|
|
AUDIO 1 |
2 AUDIO OUT USB |
|
IN |
|
|
S-Video Tape |
RGB OUT |
CONTROL |
|
|
|
Recorder |
|
|
*DVI:CP-X430 only
Computer
(notebook type)
Speaker with |
Computer |
amplifier |
(desktop type) |
NOTE • When connecting with a notebook computer, set the proper RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information.
Plug & Play
This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible.
Please use this function by connecting the RGB cable with RGB IN 1 terminal (DDC 1/2B compatible), or by connecting a DVI cable with DVI terminal (CP-X430 only/DDC 2B compatible). Plug & play may not operate by other connections.
NOTE • Plug & play is a system configured with peripheral equipment including a computer, display and an operating system.
•This projector is recognized as a plug & play monitor. Use the standard display drivers.
•Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug & play does not operate correctly.
ENGLISH-8
01CP-S420/CP-X430 03.9.2 0:08 PM 9
OPERATIONS
|
STANDBY/ |
STANDBY/ON |
BLANK |
|
STANDBY/ON Button |
ON Button |
LASER |
|
|
VIDEO |
RGB |
|||
POWER Indicator |
|
|||
|
|
|
||
|
Zoom Knob |
|
|
|
|
Focus Ring |
AUTO |
|
|
|
|
|
||
|
|
MENU |
KEYSTONE |
|
|
|
MENU SELECT |
||
|
|
POSITION |
RESET |
|
Power Switch |
|
FREEZE |
PinP |
|
|
|
|
||
|
|
MAGNIFY |
MUTE |
|
|
|
OFF |
|
Lens Cap
Power ON
1.Check that the power cord is connected correctly.
2.Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to
orange.
3.Press the STANDBY/ON button on the control panel or the remote control transmitter. Warm-up begins and the POWER indicator blinks in green.
4.The POWER indicator ceases blinking and turns to green when power is on. Remove the lens cap.
5.Adjust picture size using the zoom knob.
6.Adjust focus using the focus ring .
Power OFF
1.Press the STANDBY/ON button on the control panel or the remote controller. Then,the message "Power off?" will appear on the screen, and the message will disappear by any operation
or no operation for 5 seconds. During this message indication, press the STANDBY/ON button again. The projector lamp is extinguished and lamp cooling begins. The POWER indicator
blinks orange during lamp cooling. Pressing the STANDBY/ON button has no effect while the POWER indicator is blinking.
2.The system assumes the Standby mode when cooling is complete, and the POWER indicator ceases blinking and changes to orange. Check that the indicator is orange and set the power switch to [O].
3.The POWER indicator is extinguished when power is off. Do not forget to attach the lens cap.
WARNING • Please read this manual, and the separate “SAFETY INSTRUCTIONS” thoroughly before using the equipment. Always ensure that
the equipment is used safely.
NOTE • Except in emergencies, follow the above-mentioned procedure for turning power off. If the projector is used improperly, it may very difficult to turn off the projector caused by heating inside the unit. And the reduction of life time of lamp and LCD panels will be caused by incorrect procedure.
•To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF. Providing a RS-232C cable is connected, turn on the computer before the projector.
•When a projector continues projecting the same image, the image may remain as an afterimage. Please do not project the image same for a long time.
ENGLISH
ENGLISH-9
01CP-S420/CP-X430 03.9.2 0:08 PM 10
OPERATIONS (continued)
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
Item |
Description |
Select Input Signal (*) : Press the INPUT button.
RGB IN 1→RGB IN 2→DVI→ VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ RGB IN 1)
Select RGB Input : Press the RGB button.
VIDEO IN / S-VIDEO IN / COMPONENT VIDEO → RGB IN 1 / RGB IN 2 / DVI
INPUT
RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)
SELECT
Select Video Input : Press the VIDEO button.
RGB IN 1 / RGB IN 2 / DVI → VIDEO IN / S-VIDEO IN / COMPONENT VIDEO
VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ VIDEO IN)
•The selected signal name is displayed for approximately 3 seconds when the input signal is changed.
•Only for CP-X430, DVI exists.
|
Set/Clear Position Adjustment Mode : Press the POSITION button. |
||||||
|
The [ |
] icon is displayed in the POSITION mode. |
|
|
|
|
|
|
Image Position Adjustment: Press the , |
, |
|
and buttons in the |
|||
POSITION |
POSITION mode. |
|
|
|
|
||
• Valid only in the MAGNIFY mode with a video signal is input. |
|||||||
|
|||||||
|
• After approximately 10 seconds of inactivity the [ |
] icon is extinguished and the |
|||||
|
POSITION mode is cleared automatically. |
|
|
|
|
||
|
• , |
, and buttons may operate as the mouse control button. Refer to page 4. |
|||||
|
|
||||||
|
Initialize Each Item : Select an item and press the RESET button. |
||||||
RESET (*) |
Initialize Position Adjustment : Press the RESET button and the |
||||||
POSITION mode. This function is valid only when RGB signal is input. |
|||||||
|
• Valid except for the VOLUME, LANGUAGE and H PHASE. |
||||||
|
• The RESET button may operate as the mouse control button. Refer to page 4. |
||||||
|
|
|
|||||
|
Set MAGNIFY Mode : Press the MAGNIFY |
button. |
|||||
|
Move Magnified Area : Run the POSITION in the MAGNIFY mode. |
||||||
MAGNIFY |
Adjust Magnification : Press the MAGNIFY |
/ |
|
|
button in MAGNIFY |
||
|
|
||||||
mode. |
|
|
|
|
|
||
|
Clear MAGNIFY Mode : Press the MAGNIFY OFF |
button. |
|||||
|
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT |
||||||
|
SELECT or VIDEO, or by changing the input signal. |
|
|
|
|
||
|
|
||||||
|
Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is |
||||||
|
displayed, and the image is frozen, in the FREEZE mode. |
||||||
FREEZE |
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE, |
||||||
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the |
|||||||
|
|||||||
|
input signal. |
|
|
|
|
||
|
• Do not forget to clear frozen static images. |
|
|
|
|
NOTE • Strong light and obstacles will interfere with operation of the remote control transmitter.
ENGLISH-10
01CP-S420/CP-X430 03.9.2 0:08 PM 11
OPERATIONS (continued)
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
Item |
Description |
VOLUME Volume Adjustment : Press the VOLUME / button.
MUTE
Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the MUTE mode.
Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and horizontal size(H.SIZE) are automatically adjusted. Use with the window at maximum size in the application display.
AUTO Automatic Adjustment at Video Input : Press the AUTO button. A signal type appropriate for the input signal is selected automatically. Valid only when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with some input signals.
BLANK |
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in |
|||||||||||||
ON/OFF |
the Blank mode. The screen color is as set in BLANK on the Image menu. |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MENU |
Menu Display Start/Stop: Press the MENU button. |
|
|
|
||||||||||
• The menu display is terminated automatically after approximately 10 seconds of |
||||||||||||||
ON/OFF (*) |
||||||||||||||
|
inactivity. |
|
|
|
|
|
|
|
|
|
|
|||
|
Select Menu Type: Press the MENU SELECT button. Allows the user to |
|||||||||||||
|
select the normal menu or the single menu. Only the selected item is |
|||||||||||||
|
displayed on the single menu, and other items are displayed with the |
|||||||||||||
|
and buttons as with the normal menu. |
|
|
|
|
|||||||||
|
• Valid only when the Setup menu is used. Push the MENU SELECT button after |
|||||||||||||
MENU |
selecting items such as "BRIGHTNESS". |
|
|
|
|
|||||||||
• The MENU SELECT button may operate as the mouse control button. Refer to |
||||||||||||||
SELECT |
||||||||||||||
page 4. |
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
||||
|
Normal menu |
Single menu |
||||||||||||
|
|
|
|
|
|
|
(MENU SELECT) |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
SETUP INPUT IMAGE OPT. |
|
|
|
|
|
|
|
|
|||
|
|
|
BRIGHT |
0 |
|
|
|
|
|
|
|
|
||
|
|
|
CONTRAST |
|
-2 |
|
|
|
|
|
|
|
|
|
|
|
|
V POSIT |
100 |
|
|
|
|
|
|
|
|
||
|
|
|
H POSIT |
100 |
|
|
|
|
|
|
|
|
||
|
|
|
H PHASE |
|
+1 |
|
|
|
|
|
|
|
|
|
|
|
|
H SIZE |
800 |
|
|
|
|
|
|
|
|
||
|
|
|
COLOR BAL R |
|
0 |
|
|
|
|
|
|
|
|
|
|
|
|
COLOR BAL B |
|
0 |
|
|
|
|
|
|
|
|
|
|
|
|
ASPECT |
|
|
|
|
|
|
CONTRAST |
|
-2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P.IN P.
Select Mode of P.IN P. Display : Press the PinP button.
MODE
Small → Large → P.IN P. off ( → Small)
• P.IN P. function superimposes a video image over RGB or DVI signals.
Set / Clear KEYSTONE Mode (*) : Press the KEYSTONE button. Select KEYSTONE Mode : Press the / button in the KEYSTONE
mode. Vertical ↔ Horizontal KEYSTONE Adjust KEYSTONE : Press the / button.
•The image may not be appeared properly when this function is activated on same input signals.
•The adjustable range of distortion correction will be different among input signals.
ENGLISH
ENGLISH-11