Loading...
Dell™ PowerVault™
MD3200i and MD3220i
Storage Arrays
Owner’s Manual
Regulatory Model: E03J Series and E04J Series Regulatory Type: E03J001 and E04J001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice. © 2010 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, OpenManage, PowerEdge, and PowerVault are trademarks of Dell Inc. Microsoft, Windows, Internet Explorer, MS-DOS, and Windows Server are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries; Red Hat and Red Hat Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States and other countries; SUSE is a registered trademark of Novell, Inc. in the United States and other countries; VMware is a registered trademark of VMware, Inc. in the United States and/or other jurisdictions.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Regulatory Model: E03J Series and E04J Series
Regulatory Type: E03J001 and E04J001
May 2010 |
Rev. A00 |
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 19
About This Document . . . . . . . . . . . . . . . . . . |
19 |
Inside the box of the Dell PowerVault MD3200i |
|
Series Storage Array. . . . . . . . . . . . . . . . . . . |
19 |
Dell PowerVault MD3200i |
20 |
Series Storage Array . . . . . . . . . . . . . . . . |
|
Dell PowerVault Modular |
|
Disk Storage Manager |
20 |
. . . . . . . . . . . . . . . . . . . . . . . . . . . |
|
Dell PowerVault Modular Disk Configuration Utility |
20 |
Other Information You May Need . . . . . . . . . . . . |
20 |
2 Planning: About Your Storage Array . . . . 23
Overview . . . . . . . . . . . . . . . . . . . . . . . . . |
23 |
Hardware Features . . . . . . . . . . . . . . . . . . . |
24 |
Front-Panel Features and Indicators . . . . . . . |
24 |
Back Panel Features and Indicators . . . . . . . . |
27 |
Hard-Drive Indicator Patterns . . . . . . . . . . . . . . |
28 |
Power Supply and Cooling Fan Features . . . . . . . . |
29 |
Power Indicator Codes . . . . . . . . . . . . . . . . . |
30 |
Contents 3
3 Planning: RAID Controller Modules . . . . 31
RAID Controller Modules . . . . . . . . . . . . . . . . |
31 |
RAID Controller Module Connectors and Features . . . |
32 |
RAID Controller Module—Additional Features . . . . . |
34 |
Battery Backup Unit . . . . . . . . . . . . . . . . |
34 |
Storage Array Thermal Shutdown . . . . . . . . . |
34 |
System Password Reset . . . . . . . . . . . . . . |
35 |
Cache Functions and Features. . . . . . . . . . . . . . |
35 |
Cache Mirroring. . . . . . . . . . . . . . . . . . . |
35 |
Write-Back Cache . . . . . . . . . . . . . . . . . |
35 |
Write-Through Cache . . . . . . . . . . . . . . . . |
36 |
4Planning: MD3200i Series Storage
Array Terms and Concepts . . . . . . . . . . . 37
Physical Disks, Virtual Disks, and Disk Groups . . . . . |
37 |
Physical Disks . . . . . . . . . . . . . . . . . . . . |
37 |
Physical Disk States . . . . . . . . . . . . . . . . |
38 |
Self-Monitoring Analysis |
|
and Reporting Technology . . . . . . . . . . . . . |
39 |
Virtual Disks and Disk Groups . . . . . . . . . . . |
39 |
Virtual Disk States . . . . . . . . . . . . . . . . . |
40 |
RAID Levels. . . . . . . . . . . . . . . . . . . . . . . . |
40 |
RAID Level Usage . . . . . . . . . . . . . . . . . . |
41 |
Segment Size . . . . . . . . . . . . . . . . . . . . . . . |
42 |
Virtual Disk Operations . . . . . . . . . . . . . . . . . |
43 |
Virtual Disk Initialization . . . . . . . . . . . . . . |
43 |
Background Initialization . . . . . . . . . . . . . . |
43 |
Foreground Initialization . . . . . . . . . . . . . . |
43 |
4 Contents
Consistency Check . . . . . . . . . . . . . . . . . |
43 |
Media Verification . . . . . . . . . . . . . . . . . |
44 |
Cycle Time . . . . . . . . . . . . . . . . . . . . . |
44 |
Virtual Disk Operations Limit . . . . . . . . . . . . |
44 |
Disk Group Operations. . . . . . . . . . . . . . . . . . |
45 |
RAID Level Migration . . . . . . . . . . . . . . . . |
45 |
Segment Size Migration . . . . . . . . . . . . . . |
45 |
Virtual Disk Capacity Expansion . . . . . . . . . . |
46 |
Disk Group Expansion . . . . . . . . . . . . . . . |
46 |
Disk Group Defragmentation . . . . . . . . . . . . |
46 |
Disk Group Operations Limit . . . . . . . . . . . . |
46 |
RAID Background Operations Priority . . . . . . . . . |
47 |
Virtual Disk Migration and Disk Roaming. . . . . . . . |
48 |
Disk Migration . . . . . . . . . . . . . . . . . . . |
48 |
Disk Roaming . . . . . . . . . . . . . . . . . . . . |
50 |
Advanced Features . . . . . . . . . . . . . . . . . . . |
50 |
Host Server-to-Virtual Disk Mapping. . . . . . . . |
50 |
Host Types . . . . . . . . . . . . . . . . . . . . . |
51 |
Snapshot Virtual Disks . . . . . . . . . . . . . . . |
51 |
Snapshot Repository Virtual Disk. . . . . . . . . . |
52 |
Virtual Disk Copy . . . . . . . . . . . . . . . . . . |
52 |
Virtual Disk Recovery . . . . . . . . . . . . . . . . |
53 |
Using Snapshot and Disk Copy Together. . . . . . |
53 |
Multi-Path Software . . . . . . . . . . . . . . . . . . . |
54 |
Preferred and Alternate Controllers and Paths . . |
54 |
Virtual Disk Ownership . . . . . . . . . . . . . . . |
55 |
Load Balancing . . . . . . . . . . . . . . . . . . . . . |
55 |
Monitoring MD3200i Series System Performance . . . |
56 |
Contents 5
5 Configuration: Overview . . . . . . . . . . . . |
59 |
User Interface . . . . . . . . . . . . . . . . . . . . . . |
59 |
Enterprise Management Window . . . . . . . . . |
60 |
Array Management Window . . . . . . . . . . . . |
61 |
6Configuration: About Your
Storage Array . . . . . . . . . . . . . . . . . . . . . 63
Out-of-Band and In-Band Management . . . . . . . . . |
63 |
Storage Arrays . . . . . . . . . . . . . . . . . . . . . . |
64 |
Adding Storage Arrays . . . . . . . . . . . . . . . |
64 |
Setting Up Your Storage Array . . . . . . . . . . . |
66 |
Locating Storage Arrays . . . . . . . . . . . . . . |
67 |
Naming or Renaming Storage Arrays. . . . . . . . |
68 |
Setting a Password . . . . . . . . . . . . . . . . . |
69 |
Viewing Storage Array Connections . . . . . . . . |
70 |
Adding/Editing a Comment to an |
|
Existing Storage Array . . . . . . . . . . . . . . . |
71 |
Removing Storage Arrays. . . . . . . . . . . . . . |
71 |
Enabling Premium Features. . . . . . . . . . . . . |
72 |
Failover Alert Display . . . . . . . . . . . . . . . . |
72 |
Changing the Cache Settings |
|
on the Storage Array . . . . . . . . . . . . . . . . |
72 |
Changing Expansion Enclosure |
|
ID Numbers . . . . . . . . . . . . . . . . . . . . . |
73 |
Changing the Enclosure Order |
|
in the Physical Pane . . . . . . . . . . . . . . . . |
73 |
Configuring Alert Notifications . . . . . . . . . . . . . |
74 |
Configuring E-mail Alerts . . . . . . . . . . . . . . |
74 |
Configuring SNMP Alerts . . . . . . . . . . . . . . |
77 |
Battery Settings . . . . . . . . . . . . . . . . . . . . . |
78 |
6 Contents
|
Setting the Storage Array RAID |
|
|
Controller Module Clocks. . . . . . . . . . . . . . |
79 |
7 |
Configuration: Using iSCSI . . . . . . . . . . . |
81 |
|
Changing the iSCSI Target Authentication . . . . . . . |
81 |
|
Entering Mutual Authentication Permissions. . . . . . |
82 |
|
Creating CHAP Secrets . . . . . . . . . . . . . . . . . |
82 |
|
Initiator CHAP Secret. . . . . . . . . . . . . . . . |
83 |
|
Target CHAP Secret . . . . . . . . . . . . . . . . |
83 |
|
Valid Characters for CHAP Secrets . . . . . . . . |
83 |
|
Changing the iSCSI Target Identification . . . . . . . . |
84 |
|
Changing the iSCSI Target Discovery Settings . . . . . |
84 |
|
Configuring the iSCSI Host Ports . . . . . . . . . . . . |
85 |
|
Advanced iSCSI Host Ports Settings . . . . . . . . . . |
87 |
|
Viewing or Ending an iSCSI Session . . . . . . . . . . |
88 |
|
Viewing iSCSI Statistics and |
89 |
|
Setting Baseline Statistics . . . . . . . . . . . . . . . |
|
|
Edit, Remove, or Rename Host Topology . . . . . . . . |
90 |
8 |
Configuration: Event Monitor . . . . . . . . . |
91 |
|
Enabling or Disabling the Event Monitor . . . . . . . . |
91 |
|
Windows . . . . . . . . . . . . . . . . . . . . . . |
92 |
|
Linux . . . . . . . . . . . . . . . . . . . . . . . . |
92 |
Contents 7
9 Configuration: About Your Host . . . . . . . |
93 |
Configuring Host Access. . . . . . . . . . . . . . . . . |
93 |
Using the Mappings Tab . . . . . . . . . . . . . . . . . |
94 |
Defining a Host . . . . . . . . . . . . . . . . . . . |
94 |
Removing Host Access. . . . . . . . . . . . . . . . . . |
96 |
Managing Host Groups. . . . . . . . . . . . . . . . . . |
96 |
Creating a Host Group . . . . . . . . . . . . . . . |
96 |
Moving a Host to a Different Host Group . . . . . . |
97 |
Removing a Host Group . . . . . . . . . . . . . . . |
98 |
Host Topology . . . . . . . . . . . . . . . . . . . . |
98 |
Starting or Stopping the Host Context Agent . . . . |
99 |
I/O Data Path Protection . . . . . . . . . . . . . . . . |
100 |
Managing Host Port Identifiers . . . . . . . . . . . . |
101 |
10Configuration: Disk Groups
and Virtual Disks . . . . . . . . . . . . . . . . . . 103
Creating Disk Groups and Virtual Disks . . . . . . . . |
103 |
Creating Disk Groups . . . . . . . . . . . . . . . |
104 |
Locating a Disk Group . . . . . . . . . . . . . . |
106 |
Creating Virtual Disks . . . . . . . . . . . . . . . |
106 |
Changing the Virtual Disk |
|
Modification Priority . . . . . . . . . . . . . . . |
108 |
Changing the Virtual Disk Cache Settings . . . . |
109 |
Changing the Segment Size of a Virtual Disk . . . |
111 |
Changing the I/O Type. . . . . . . . . . . . . . . |
112 |
Choosing an Appropriate Physical Disk Type . . . . . |
113 |
Physical Disk Security with Self Encrypting Disk . . |
113 |
8 Contents
Creating a Security Key. . . . . . . . . . . . . . . |
116 |
Changing a Security Key . . . . . . . . . . . . . . |
117 |
Saving a Security Key . . . . . . . . . . . . . . . |
119 |
Unlocking Secure Physical Disks. . . . . . . . . . |
120 |
Erasing Secure Physical Disks . . . . . . . . . . . |
120 |
Configuring Hot Spare Physical Disks . . . . . . . . . |
121 |
Hot Spares and Rebuild. . . . . . . . . . . . . . . |
123 |
Global Hot Spares . . . . . . . . . . . . . . . . . |
123 |
Hot Spare Operation . . . . . . . . . . . . . . . . |
123 |
Hot Spare Drive Protection . . . . . . . . . . . . . |
123 |
Enclosure Loss Protection . . . . . . . . . . . . . . . . |
124 |
Host-to-Virtual Disk Mapping . . . . . . . . . . . . . . |
126 |
Creating Host-to-Virtual Disk Mappings . . . . . . |
126 |
Modifying and Removing |
|
Host-to-Virtual Disk Mapping. . . . . . . . . . . . |
128 |
Changing Controller Ownership |
|
of the Virtual Disk . . . . . . . . . . . . . . . . . . |
129 |
Removing Host-to-Virtual Disk Mapping . . . . . . |
129 |
Changing the RAID Controller |
|
Module Ownership of a Disk Group . . . . . . . . |
130 |
Changing the RAID Level of a Disk Group . . . . . |
131 |
Restricted Mappings. . . . . . . . . . . . . . . . . . . |
132 |
Changing the RAID Controller Module
Ownership of a Virtual Disk or a Disk Group . . . . 133
Changing the RAID Level of a Disk Group. . . . . . . . |
135 |
Storage Partitioning . . . . . . . . . . . . . . . . . . . |
136 |
Disk Group and Virtual Disk Expansion . . . . . . . . . |
137 |
Disk Group Expansion . . . . . . . . . . . . . . . |
137 |
Virtual Disk Expansion . . . . . . . . . . . . . . . |
138 |
Using Free Capacity . . . . . . . . . . . . . . . . |
138 |
Contents 9
Using Unconfigured Capacity. . . . . . . . . . . |
138 |
Disk Group Migration . . . . . . . . . . . . . . . . . |
139 |
Export Disk Group . . . . . . . . . . . . . . . . . |
139 |
Exporting a Disk Group . . . . . . . . . . . . . . |
140 |
Import Disk Group . . . . . . . . . . . . . . . . . . . |
140 |
Importing a Disk Group . . . . . . . . . . . . . . |
140 |
Storage Array Media Scan. . . . . . . . . . . . . . . |
141 |
Changing Media Scan Settings. . . . . . . . . . |
142 |
Suspending the Media Scan . . . . . . . . . . . |
143 |
11Configuration: Premium Feature— Snapshot Virtual Disks . . . . . . . . . . . . . 145
Creating a Snapshot Virtual Disk |
|
Using the Simple Path . . . . . . . . . . . . . . . . . |
146 |
About the Simple Path . . . . . . . . . . . . . . |
146 |
Preparing Host Servers to Create the |
|
Snapshot Using the Simple Path . . . . . . . . . |
147 |
Creating a Snapshot Virtual Disk |
|
Using the Advanced Path . . . . . . . . . . . . . . . |
149 |
About the Advanced Path. . . . . . . . . . . . . |
149 |
Preparing Host Servers to Create |
|
the Snapshot Using the Advanced Path . . . . . |
151 |
Creating the Snapshot |
|
Using the Advanced Path . . . . . . . . . . . . . |
153 |
Specifying Snapshot Virtual Disk Names . . . . . . . |
154 |
Snapshot Repository Capacity . . . . . . . . . . . . . |
156 |
Re-creating Snapshot Virtual Disks . . . . . . . . . . |
159 |
10 Contents
Disabling a Snapshot Virtual Disk. . . . . . . . . . . . 159
Preparing Host Servers to Re-create
a Snapshot Virtual Disk . . . . . . . . . . . . . . . 160
Re-creating a Snapshot Virtual Disk . . . . . . . . . . 161
12Configuration: Premium Feature—
Virtual Disk Copy . . . . . . . . . . . . . . . . . . 163
Creating a Virtual Disk Copy for |
|
|
|
an MSCS Shared Disk . . . . . . . . . . . . . . . . . . |
164 |
|
|
Virtual Disk Read/Write Permissions . . . . . . . . . . |
165 |
|
|
Virtual Disk Copy Restrictions. . . . . . . . . . . . . . |
165 |
|
|
Creating a Virtual Disk Copy. . . . . . . . . . . . . . . |
166 |
|
|
Before you Begin . . . . . . . . . . . . . . . . . . |
167 |
|
|
Virtual Disk Copy and |
|
|
|
Modification Operations . . . . . . . . . . . . . . |
167 |
|
|
Create Copy Wizard . . . . . . . . . . . . . . . . |
167 |
|
|
Failed Virtual Disk Copy. . . . . . . . . . . . . . . |
168 |
|
|
Preferred RAID Controller Module Ownership . . . . . |
168 |
|
|
Failed RAID Controller Module . . . . . . . . . . . . . |
168 |
|
|
Copy Manager . . . . . . . . . . . . . . . . . . . . . . |
169 |
|
|
Copying the Virtual Disk . . . . . . . . . . . . . . . . . |
169 |
|
|
Storage Array Performance |
170 |
|
|
During Virtual Disk Copy . . . . . . . . . . . . . . . . |
|
|
|
Setting Copy Priority . . . . . . . . . . . . . . . . . . . |
170 |
|
|
Stopping a Virtual Disk Copy . . . . . . . . . . . . . . |
171 |
|
|
Recopying a Virtual Disk . . . . . . . . . . . . . . . . |
172 |
|
|
Contents |
|
|
11 |
|
Preparing Host Servers to |
|
Recopy a Virtual Disk . . . . . . . . . . . . . . . |
172 |
Recopying the Virtual Disk . . . . . . . . . . . . |
173 |
Removing Copy Pairs. . . . . . . . . . . . . . . . . . |
174 |
13Configuration: Premium Feature—Upgrading to High-Performance-Tier . . . . . . . . . . . 175
14Configuration: Device Mapper
Multipath for Linux . . . . . . . . . . . . . . . . 177
Overview . . . . . . . . . . . . . . . . . . . . . . . . |
177 |
Using DM Multipathing Devices. . . . . . . . . . . . |
178 |
Prerequisite Steps . . . . . . . . . . . . . . . . |
178 |
Device Mapper Configuration Steps . . . . . . . |
179 |
Linux Host Server Reboot Best Practices . . . . |
183 |
Important Information About Special Partitions . |
183 |
Limitations and Known Issues . . . . . . . . . . . . . |
184 |
Troubleshooting . . . . . . . . . . . . . . . . . . . . |
185 |
15 Management: Firmware Downloads . . . |
187 |
Downloading RAID Controller |
|
and NVSRAM Packages . . . . . . . . . . . . . . . . |
187 |
Downloading Both RAID Controller |
|
and NVSRAM Firmware . . . . . . . . . . . . . . . . |
188 |
Downloading Only NVSRAM Firmware . . . . . . . . |
190 |
Downloading Physical Disk Firmware . . . . . . . . |
192 |
12 Contents
Downloading MD1200 Series Expansion
Module EMM Firmware . . . . . . . . . . . . . . . . . 194
Self-Monitoring Analysis and
Reporting Technology (SMART) . . . . . . . . . . . . . 196
Media Errors and Unreadable Sectors . . . . . . . . . 196
16Management: Installing
Array Components . . . . . . . . . . . . . . . . 197
Recommended Tools. . . . . . . . . . . . . . . . . . . |
197 |
Front Bezel (Optional) . . . . . . . . . . . . . . . . . . |
198 |
Removing the Front Bezel . . . . . . . . . . . . . |
198 |
Installing the Front Bezel . . . . . . . . . . . . . . |
198 |
Hard Drives. . . . . . . . . . . . . . . . . . . . . . . . |
199 |
Removing a Drive Blank . . . . . . . . . . . . . . |
199 |
Installing a Drive Blank . . . . . . . . . . . . . . . |
200 |
Removing a Hard Drive . . . . . . . . . . . . . . . |
200 |
Installing a Hard Drive . . . . . . . . . . . . . . . |
202 |
Removing a Hard Drive |
|
From a Hard-Drive Carrier . . . . . . . . . . . . . |
202 |
Installing a Hard Drive Into a Drive Carrier. . . . . |
205 |
RAID Controller Module . . . . . . . . . . . . . . . . . |
205 |
Removing a RAID Controller Module Blank . . . . |
205 |
Installing a RAID Controller Module Blank . . . . . |
206 |
Removing a RAID Controller Module . . . . . . . . |
207 |
Installing a RAID Controller Module . . . . . . . . |
208 |
Opening the RAID Controller Module . . . . . . . |
208 |
Closing the RAID Controller Module . . . . . . . . |
209 |
RAID Controller Module Backup Battery Unit . . . . . |
210 |
Contents 13
|
Removing the RAID Controller |
|
|
Module Backup Battery Unit . . . . . . . . . . . |
210 |
|
Installing the RAID Controller |
|
|
Module Backup Battery Unit . . . . . . . . . . . |
211 |
|
Power Supply/Cooling Fan Module . . . . . . . . . . |
211 |
|
Removing a Power Supply/Cooling |
211 |
|
Fan Module . . . . . . . . . . . . . . . . . . . . |
|
|
Installing a Power Supply/Cooling |
|
|
Fan Module . . . . . . . . . . . . . . . . . . . . |
214 |
|
Control Panel . . . . . . . . . . . . . . . . . . . . . . |
215 |
|
Removing the Control Panel . . . . . . . . . . . |
215 |
|
Installing the Control Panel . . . . . . . . . . . . |
216 |
|
Backplane . . . . . . . . . . . . . . . . . . . . . . . |
217 |
|
Removing the Backplane . . . . . . . . . . . . . |
217 |
|
Installing the Backplane . . . . . . . . . . . . . |
220 |
17 |
Management: Firmware Inventory . . . . |
221 |
|
Viewing the Firmware Inventory . . . . . . . . . . . |
221 |
18 |
Management: System Interfaces . . . . . . |
223 |
|
Microsoft Services. . . . . . . . . . . . . . . . . . . |
223 |
|
Virtual Disk Service . . . . . . . . . . . . . . . . |
223 |
|
Volume Shadow-Copy Service . . . . . . . . . . |
223 |
19Troubleshooting: Your Storage
Array Software . . . . . . . . . . . . . . . . . . . 225
Start-Up Routine . . . . . . . . . . . . . . . . . . . . |
225 |
14 Contents
Device Health Conditions . . . . . . . . . . . . . . . . |
225 |
Storage Array Support Data . . . . . . . . . . . . . . . |
229 |
Automatically Collect the Support Bundle Data . . . . |
229 |
Collecting the Physical Disk Data . . . . . . . . . . . . |
230 |
Event Log . . . . . . . . . . . . . . . . . . . . . . . . . |
231 |
Recovery Guru . . . . . . . . . . . . . . . . . . . . . . |
232 |
Storage Array Profile . . . . . . . . . . . . . . . . . . |
232 |
Viewing the Logical Associations. . . . . . . . . . . . |
234 |
Viewing the Physical Associations . . . . . . . . . . . |
234 |
Finding Nodes . . . . . . . . . . . . . . . . . . . . . . |
235 |
Using Go To . . . . . . . . . . . . . . . . . . . . . . . |
236 |
Recovering From an Unresponsive |
|
Storage Array Condition . . . . . . . . . . . . . . . . . |
237 |
Locating a Physical Disk. . . . . . . . . . . . . . . . . |
240 |
Locating an Expansion Enclosure . . . . . . . . . . . . |
241 |
Capturing the State Information . . . . . . . . . . . . . |
242 |
SMrepassist Utility . . . . . . . . . . . . . . . . . . . |
243 |
Unidentified Devices . . . . . . . . . . . . . . . . . . |
244 |
Recovering From an Unidentified Storage Array . . . . 244 |
|
Starting or Restarting the Host |
|
Context Agent Software . . . . . . . . . . . . . . . . . |
246 |
Contents 15
20 Troubleshooting: Your Array . . . . . . . . . |
249 |
Safety First—For you and Your Array . . . . . . . . . |
249 |
Troubleshooting Storage Array Startup Failure . . . . |
249 |
Troubleshooting Loss of Communication . . . . . . . |
249 |
Troubleshooting External Connections . . . . . . . . |
249 |
Troubleshooting Power Supply/Cooling |
|
Fan Module . . . . . . . . . . . . . . . . . . . . . . . |
250 |
Troubleshooting Array Cooling Problems . . . . . . . |
251 |
Troubleshooting Expansion |
251 |
Enclosure Management Modules . . . . . . . . . . . |
|
Troubleshooting RAID Controller Modules . . . . . . |
253 |
Troubleshooting Hard Drives . . . . . . . . . . . . . |
254 |
Troubleshooting Array and |
|
Expansion Enclosure Connections . . . . . . . . . . |
255 |
Troubleshooting a Wet Storage Array . . . . . . . . . |
255 |
Troubleshooting a Damaged Array . . . . . . . . . . |
256 |
Troubleshooting RAID Controller Modules . . . . . . |
257 |
Conditions . . . . . . . . . . . . . . . . . . . . . |
257 |
Invalid Storage Array . . . . . . . . . . . . . . . |
257 |
ECC Errors. . . . . . . . . . . . . . . . . . . . . |
257 |
PCI Errors . . . . . . . . . . . . . . . . . . . . . |
258 |
Critical Conditions. . . . . . . . . . . . . . . . . |
258 |
Noncritical Conditions . . . . . . . . . . . . . . |
258 |
16 Contents
21 Getting Help . . . . . . . . . . . . . . . . . . . . . . 259
Contacting Dell . . . . . . . . . . . . . . . . . . . . . 259
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Contents 17
18 Contents
1
Introduction
See the Safety, Environmental, and Regulatory Information document for important safety information before following any procedures listed in this document.
About This Document
This guide familiarizes you with the functions of the MD3200i Series storage array. The guide is organized according to the tasks that you must complete after receiving your Dell™ PowerVault™ MD3200i Series storage array.
Planning—Information about the storage array and its features.
Configuration—Tasks that must be completed to ensure that your storage array performs optimally.
Management—Tasks the may be performed to ensure the storage array components are up to date and performing properly, including removal and installation of storage array components.
Troubleshooting—Tasks that you must complete to resolve problems that may occur with the storage array.
Additional information on these and other topics can be found in the Dell PowerVault MD3200i and MD3220i Storage Array Deployment Guide, available at support.dell.com/manuals.
Inside the box of the Dell PowerVault MD3200i Series Storage Array
Unless specified MD3200i Series represents Dell PowerVault MD3200i and Dell PowerVault MD3220i.
Your MD3200i Series product package includes:
•Dell PowerVault MD3200i Series storage array
•Power cables
•Bezel (optional)
Introduction 19
•Mounting rails (2) (optional)
•Dell PowerVault MD3200i Series resource media
•The Rack Installation Instructions included with your rack solution describes how to install your enclosure into a rack.
•Getting Started With Your System provides an overview of enclosure features, setting up your enclosure, and technical specifications.
Dell PowerVault MD3200i Series Storage Array
The Dell PowerVault MD3200i Series is a 2U rack-mounted external redundant array of independent disks (RAID) storage array capable of accommodating up to 12 3.5-inch or 24 2.5-inch 6.0-Gbps Serial-Attached SCSI (SAS) disks. The MD3200i Series storage arrays can be daisy-chained with MD1200 Series expansion enclosures, providing access to a maximum of 96 disks in the entire storage system. Connectivity between the storage array and the host server is provided by a standard Ethernet connection.
Dell PowerVault Modular Disk Storage Manager
Dell PowerVault Modular Disk Storage Manager (MDSM) is a graphical user interface (GUI) application, used to configure and manage one or more MD3200i Series Storage Arrays. The MDSM software is located on the MD3200i Series resource media.
Dell PowerVault Modular Disk Configuration Utility
Dell PowerVault Modular Disk Configuration Utility (MDCU) is an iSCSI configuration wizard that can be used in conjunction with MDSM to simplify the configuration of iSCSI connections. The MDCU software is located on the MD3200i Series resource media.
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document.
•Getting Started Guide provides an overview of setting up and cabling your storage array.
20 Introduction
•Deployment Guide provides installation and configuration instructions for both software and hardware.
•Storage Manager CLI Guide provides information about using the command line interface (CLI).
•Resource media contains all system management tools.
•Systems Support Matrix provides information on supported software and hardware for MD systems. The document is available at support.dell.com/manuals.
•Dell PowerEdge® Cluster Documentation is available at dell.com/ha.
•Release notes or readme files are included to provide last-minute updates to the enclosure or documentation or advanced technical reference material intended for experienced users or technicians.
•This document as well as Dell PowerVault MD 1200 series installation guide is available at support.dell.com/manuals for users who incorporate MD1200 expansion enclosures.
NOTE: Always check for updates on support.dell.com/manuals and read the updates first because they often supersede information in other documents.
Introduction 21
22 Introduction
2
Planning: About Your Storage Array
Overview
The MD3200i Series storage array is designed for high availability, offering redundant access to data storage. It features support for both single and dual RAID controller configuration.
The Dell™ PowerVault™ MD3200i storage array provides 1.0-Gbps 1000 BaseT connectivity to the host server and enables access to 32 physical hosts.
The MD3200i Series storage array includes:
•RAID controller module(s)
•PSU/Fan modules
•Disk drives (also called physical disk drives in this document)
•An optional front panel bezel
•A system enclosure, into which, the other components are plugged
Planning: About Your Storage Array |
|
23 |
|
Hardware Features
Front-Panel Features and Indicators
Figure 2-1. Front-Panel Features and Indicators—Dell™ PowerVault™ MD3200i
1 
2 
3 
4
5
6
Figure 2-2. Front-Panel Features and Indicators—Dell PowerVault MD3220i
1 
2 
3 
4 
5
6 
24 |
|
Planning: About Your Storage Array |
|
Figure 2-3. Front-Bezel Features and Indicators
1 
2 
3 
Item |
Indicator, Button, or |
Icon |
Description |
|
|
Connector |
|
|
|
|
|
|
|
|
1 |
Enclosure status LED |
|
|
The enclosure status LED lights when the |
|
|
|
|
enclosure power is on. |
|
|
|
|
Lights blue during normal operation. |
|
|
|
|
Blinks blue when a host server is identifying the |
|
|
|
|
enclosure or when the system identification |
|
|
|
|
button is pressed. |
|
|
|
|
Lights amber as enclosure boots or is reset. |
|
|
|
|
Blinks amber when the enclosure is either in a |
|
|
|
|
fault state or the hosts are not using the |
|
|
|
|
preferred path to a virtual disk. |
2 |
Power LED |
|
|
The power LED lights green when at least one |
|
|
|||
|
|
|||
|
|
|
|
power supply is supplying power to |
|
|
|
|
the enclosure. |
Planning: About Your Storage Array |
|
25 |
|
Item |
Indicator, Button, or Icon |
Description |
|||
|
Connector |
|
|||
|
|
|
|
|
|
3 |
Split mode LED |
|
|
This LED should be unlit as the split mode |
|
|
|||||
|
|
|
|
|
function is not supported by the MD3200i Series |
|
|
|
|
|
Storage Arrays. |
4 |
System identification |
The system identification button on the front |
|||
|
button |
control panel can be used to locate a particular |
|||
|
|
|
|
|
enclosure within a rack. When the button is |
|
|
|
|
|
pushed, the system status indicators on the |
|
|
|
|
|
control panel and the RAID controller module(s) |
|
|
|
|
|
blink blue until the button is pushed again. |
5 |
Hard drives |
PowerVault MD3200i—Up to 12 3.5-inch SAS |
|||
|
|
|
|
|
hot-swappable hard drives. |
|
|
|
|
|
PowerVault MD3220i—Up to 24 2.5-inch SAS |
|
|
|
|
|
hot-swappable hard drives. |
6 |
Enclosure mode |
The function of this switch is not applicable to |
|||
|
switch |
|
your storage array. However, if MD1200 Series |
||
|
|
|
|
|
expansion enclosures are daisy chained to the |
storage array, the enclosure mode switches of the MD1200 Series expansion enclosures must be set to the Unified-Mode position.
NOTE: This switch must be set prior to turning on the MD1200 series expansion enclosure. Changing the switch setting after the expansion enclosure is turned on has no effect on enclosure configuration until the expansion enclosure goes through a complete power cycle.
26 |
|
Planning: About Your Storage Array |
|
Back Panel Features and Indicators
Figure 2-4. Back-Panel Features and Indicators—Dell PowerVault MD3200i Series
1 |
2 |
3 |
|
|
|
4 |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
600W Power supply/cooling fan |
2 |
RAID Controller Module 0 |
|
module |
|
|
3 |
RAID Controller Module 1 |
4 |
600W Power supply/cooling fan |
|
|
|
module |
Planning: About Your Storage Array |
|
27 |
|
Hard-Drive Indicator Patterns
Figure 2-5. Hard Drive Indicators
1 2
|
|
|
|
|
|
1 |
hard-drive activity indicator (green) |
2 |
hard-drive status indicator (green |
||
|
|
|
|
|
and amber) |
28 |
|
Planning: About Your Storage Array |
|
Drive-Status Indicator Pattern |
Condition |
Off
Steady green
Green flashing (On 250 ms, Off 250 ms) Green flashing (On 400 ms, Off 100 ms) Amber flashing (On 150 ms, Off 150 ms)
Flashing green, amber, and off (Green On 500 ms, Amber On 500 ms, Off 1000 ms)
Flashing green, amber, and off (Green 3 seconds, amber 3 seconds, and off 3 seconds)
The physical disk is:
•not yet discovered by the host server
•has been spun down for removal
•not supported for the RAID controller module or is not in the physical disk slot
NOTE: The drive status indicator remains off until all hard drives are initialized after system power is turned on. Drives are not ready for insertion or removal during this time.
Physical disk is online
Physical disk is being identified Physical disk rebuilding Physical disk failed
Physical disk failure predicted (SMART)
Physical disk rebuild aborted
Power Supply and Cooling Fan Features
The MD3200i Series storage array includes two integrated, hot-swappable power supply/cooling fan modules. Both modules must be installed to ensure proper cooling. Each module contains two separate cooling fans. The system requires at least one of the cooling fans to function to avoid overheating.
A power supply/cooling fan module can be replaced without powering down the system. For information on removing and replacing the modules, see "Power Supply/Cooling Fan Module" on page 211.
CAUTION: A power supply/cooling fan module can be removed from a poweredon system for a maximum period of 5 minutes. Beyond that time, the system may automatically shut down to prevent damage.
Planning: About Your Storage Array |
|
29 |
|
Power Indicator Codes
Figure 2-6. Power Indicator Codes
1
2
3
4
5 |
|
Item |
|
LED Type |
Icon Description |
|
|
|
|
|
|
|
1 |
|
DC power |
|
The LED lights green when the DC output |
|
|
|
||||
|
|
|
|
|
voltage is within the limit. |
|
|
|
|
|
If this LED is off, it indicates that the DC output |
|
|
|
|
|
voltage are not within the limit. |
2 |
|
Power supply/cooling |
|
The LED lights amber when the DC output |
|
|
|
|
fan fault |
|
voltage is not within the limit or a fault with the |
|
|
|
|
|
fan is detected. |
|
|
|
|
|
If this LED is off, it indicates that no fault |
|
|
|
|
|
condition is present. |
3 |
|
AC power |
|
The LED lights green when the AC input voltage |
|
|
|
|
|
|
is within the limit. |
|
|
|
|
|
If this LED is off, it indicates either there is no |
|
|
|
|
|
power or the AC input voltage is not within the |
|
|
|
|
|
limit. |
4 |
|
Power connector |
|
Connect the external power supply to this |
|
|
|
|
|
|
connector. |
5 |
|
Power switches (2) |
|
The power switch controls the power supply |
|
|
|
|
|
|
output to the enclosure. |
|
|
|
|
|
|
30 |
|
Planning: About Your Storage Array |
|||
|
|||||
Loading...