NL6FT
Tropical Compressor
R134a
220-240V 50/60Hz
General
Code number |
|
|
|
|
|
105G6628 |
|
|
|||
Approvals |
|
|
|
|
EN 60335-2-34, CCC |
|
|||||
Compressors on pallet |
|
|
|
|
|
80 |
|
|
|
||
Application |
|
|
|
|
|
|
|
|
|
|
|
Application |
|
|
|
|
|
LBP |
|
|
|||
Frequency |
|
Hz |
|
50 |
|
|
|
|
60 |
|
|
Evaporating temperature |
|
°C |
-35 to -10 |
|
-35 to -10 |
||||||
Voltage range |
|
V |
187 - 254 |
|
198 - 254 |
||||||
Max. condensing temperature continuous (short) |
°C |
|
60 (70) |
|
60 (70) |
||||||
Max. winding temperature continuous (short) |
°C |
125 (135) |
|
125 (135) |
|||||||
Cooling requirements |
|
|
|
|
|
|
|
|
|
|
|
Frequency |
|
Hz |
|
50 |
|
|
|
|
60 |
|
|
Application |
|
|
LBP |
|
MBP |
HBP |
|
LBP |
|
MBP |
HBP |
32°C |
|
|
S |
|
– |
– |
|
– |
|
– |
– |
38°C |
|
|
S |
|
– |
– |
|
– |
|
– |
– |
43°C |
|
|
S |
|
– |
– |
|
– |
|
– |
– |
Remarks on application: In capillary tube systems where non-equalized pressures may |
|||||||||||
occur at compressor start, or in areas with short power supply drop-outs, a starting |
|
||||||||||
capacitor can be used for ensuring a successful start (CSIR). |
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
Motor |
|
|
|
|
|
|
|
|
|
|
|
Motor type |
|
|
|
|
|
RSIR/CSIR |
|
|
|||
LRA (rated after 4 sec. UL984), HST | LST |
A |
|
7.4 |
|
|
|
|
5.9 |
|
||
Cut in Current, HST | LST |
|
A |
|
7.4 |
|
|
|
|
10.3 |
|
|
Resistance, main | start winding (25°C) |
Ω |
|
12.6 |
|
|
|
|
12.4 |
|
||
Design |
|
|
|
|
|
|
|
|
|
|
|
Displacement |
|
cm3 |
|
|
|
6.13 |
|
|
|
||
Oil quantity (type) |
|
cm3 |
|
|
|
320 |
|
|
|
||
Maximum refrigerant charge |
|
g |
|
|
|
400 |
|
|
|
||
Free gas volume in compressor |
|
cm3 |
|
|
|
2360 |
|
|
|
||
Weight without electrical equipment |
kg |
|
|
|
10.0 |
|
|
|
|||
Dimensions |
|
|
|
|
|
|
|
|
|
|
|
Height |
|
mm |
A |
|
|
197 |
|
|
|
||
|
|
|
B |
|
|
191 |
|
|
|
||
|
|
|
B1 |
|
|
|
– |
|
|
||
|
|
|
B2 |
|
|
|
– |
|
|
||
Suction connector |
location/I.D. mm | angle |
C |
|
|
6.2 | 15° |
|
|
|
|||
|
material | comment |
|
Cu-plated steel | Al cap |
||||||||
Process connector |
location/I.D. mm | angle |
D |
|
|
6.2 | 25° |
|
|
|
|||
|
material | comment |
|
Cu-plated steel | Al cap |
||||||||
Discharge connector |
location/I.D. mm | angle |
E |
|
|
5.0 | 35° |
|
|
|
|||
|
|
|
|
||||||||
|
material | comment |
|
Cu-plated steel | Al cap |
||||||||
|
|
|
|
|
|
|
|
|
|||
Oil cooler connector |
location/I.D. mm | angle |
F |
|
|
|
– |
|
|
|||
|
material | comment |
|
|
|
|
– |
|
|
|||
|
|
|
|||||||||
Connector tolerance |
I.D. mm |
±0.09, on 5.0 +0.12/+0.20 |
|||||||||
Remarks: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
S = Static cooling normally sufficient
O= Oil cooling
F1 |
= Fan cooling 1.5 m/s |
|
(compressor compartment temperature |
|
equal to ambient temperature) |
F2 |
= Fan cooling 3.0 m/s necessary |
SG |
= Suction gas cooling normally sufficent |
–= not applicable in this area
June 2012 |
Manufactured by Secop for Danfoss - DEHC.ED.401.M1.02 / 520N1332 |
1/2 |
Loading...