Bosch ISC-FPB1-W60QS, ISC-FPB1-W60QF, ISC-FPB1-W200QS, ISC-FPB1-W200QF, ISC-FPB1-W120QS Specsheet

Intrusion Alarm Systems | Photobeam 5000

Photobeam 5000

www.boschsecurity.com

u Quad beam detection

u Environmental discrimination circuit

u Beam power control to reduce cross-talk

The Photobeam 5000 Series consists of the single channel quad beam ISC-FPB1-W60QS, ISC-FPB1- W120QS, ISC-FPB1-W200QS, and the four channel quad beam ISC-FPB1-W60QF, ISC-FPB1-W120QF, and ISC-FPB1-W200QF detectors with separate transmitters and receivers.

The detector series uses four pulsed infrared beams that are designed to activate an alarm when all four beams are simultaneously blocked. False alarm immunity is increased by the utilization of four beams compared to single or dual beam models.

The detector series also features interlocked upper and lower beams, signal voltage LED, and optional environmental discrimination circuitry.

System overview

Consisting of a separate transmitter and receiver, it is designed to activate an alarm when an intruder passes within the direct line of sight between the transmitter and receiver.

Functions

Mounting features

Mounting and installing the detector is now easier than ever. Install the detector through easy-to-use mounting hole locations which provide an enlarged entry point of access to accept small to large, single or multiple cable set wires. Fastening screw locations eliminate the need for unnecessary crawling or bending during installation.

Multiple Channel Operation (4-channel models only)

Configure the detectors for up to four different channels. This allows multiple units to be used near one another without the possibility of receiver crosstalk. This is particularly useful when stacking multiple beam sets.

High Density mode (4-channel models only)

The High Density mode allows you to add an additional zones of protection to detect larger objects that only partly interrupt the beams of individual devices. This feature allows an alarm condition to be generated when beam pairs are interrupted on adjacent devices but not all four beams are interrupted on one device.

2 | Photobeam 5000

Selectable AND/OR mode (4-channel models only)

This feature allows an added level of detection by generating an alarm when four beams from two units are blocked simultaneously. Environmental conditions require higher false alarm tolerance against smaller objects passing through the detector's line of sight. To do this, set the AND/OR gate option to AND gate mode that only causes an alarm condition when all four infrared beams are interrupted simultaneously.

High Security applications might require the detection of smaller objects passing through the detector's line of sight. To do this, set the AND/OR gate option to OR gate mode that causes an alarm condition when either the upper two beams or the lower two beams are interrupted.

Dust/insect cover features

The included foam sealing ensures that the detectors are properly secured from insects and other environmental elements such as humidity and temperature fluctuations.

The improved cover design includes water flow channels to prevent water and dirt from accumulating in front of optic components, and eliminates the need for additional weatherproofing solutions.

Environmental Discrimination Circuit

Monitors gradual loss of signal due to dust, fog, rain, and snow. Normally closed output opens when signal loss reaches 90%. May be field configured to bypass alarm relay when activated.

Beam Power Control

The transmitter power output is field adjustable allowing the user to eliminate reflections and crosstalk from other units.

This feature improves catch performance and false alarm immunity, and allows for reliable installation in most applications.

Test features

High visibility reception level LED improves ease of installation. Flash rate increases as installation alignment improves.

Voltage output terminals also allow for improved alignment accuracy.

Optical module alignment switch to allow for independent adjustment of upper and lower beam pairs.

Dual Modulated beam

The Dual Modulated Beam eliminates interference from external noise sources such as sunlight, car headlights, electrical interference, etc.

Certifications and approvals

Region		Certification
Europe		CE		EMC, RoHS [ISC-FPB1-W60QF, ISC-
				FPB1-W120QF, ISC-FPB1-W200QF
				with or wihout BH12T heater]
		CE		EMC, RoHS [ISC-FPB1-W60QS, ISC-
				FPB1-W120QS, ISC-FPB1-W200QS
				with or without BH12T heater]
Technical specifications
Photobeam
		ISC-FPB1-				ISC-FPB1-	ISC-FPB1-
		W60QS				W120QS	W200QS
Maximum		120 m				240 m	400 m
indoor range		(393 ft)				(787 ft)	(1312 ft)
Maximum		60 m				120 m	200 m
outdoor range		(196 ft)				(393 ft)	(656 ft)
* Single channel quad beam series
		ISC-FPB1-				ISC-FPB1-	ISC-FPB1-
		W60QF				W120QF	W200QF
Maximum		120 m				240 m	400 m
indoor range		(393 ft)				(787 ft)	(1312 ft)
Maximum		60 m				120 m	200 m
outdoor range		(196 ft)				(393 ft)	(656 ft)
* Four channel quad beam series
Environmental considerations
Operating temperature				-25°C to +60°C (-13°F to +140°F) (96%
				or less)
Storage temperature/				-30°C to +70°C (-22°F to +158°F)
humidity				Relative Humidity 96%
IP rating (indoor)				IP66
Mounting considerations
Location				Pole mount or surface mount
Horizontal adjustability				±90°
Vertical adjustability				±10°
Distance between upper				245 mm (9.64 in)
and lower lens

Dimensions

Dimensions	103 mm x 398 mm x 99 mm
	(4.05 in. x 15.66 in. x 3.89 in.)