Blaupunkt BPV 660 User Manual

Size:
1.58 Mb
Download

Issue date 12-01288F0470

BPV 660

High-PowerFM/AM/CD Receiver with Detachable Face

Autoradio FM/AM à Lecteur CD de Forte Puissance et à Face Amovible Receptor FM/AM/Reproductor de CD de Alta Potencia y con Panel Extraíble

Rádio FM/AM/CD de Alta Potência com Face Removível

TRE

Robert Bosch Corporation Sales Group — Blaupunkt Division

2800 South 25th Avenue, Broadview, Illinois 60155 http://www.blaupunktUSA.com/

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

BPV660_Cover

1

1/22/02, 10:47 AM

FCC WARNING

Precautions

Handling the Front Panel

This equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Avoid installing the unit where it would be subject to high temperatures, such as in direct sunlight or a hot air stream from the heater, or where it would be subject to dust, dirt, or excessive vibration.

Do not turn on the unit if the temperature inside the car is very high. Always cool down the unit before usage. Parking your car in direct sunlight will result in a temperature rise.

If the unit does not turn on, check the connections first. Then check whether the fuse at the back of the unit is blown.

Carefully read this manual before using the unit. If you encounter any problems that are not covered in this manual, please consult the dealer where you purchased the unit or the dealer nearest to you.

This unit has been designed specifically for playback of compact discs bearing the following mark. Other discs cannot be played.

Features

Detachable front panel

Built-inpower amplifier (max. output : 57.5W × 4ch)

FM/AM PLL Synthesizer tuner

30 Station preset memory

Travel Store / Scan tuning

Auxiliary input

Requires use of Blaupunkt Part 7 607 897 093 and F00E500029.

Optional IR Remote Controls

CD changer control

Requires use of Blaupunkt Part F00E500029.

(IDC-A09,CDC-A08,CDC-A071,CDC-A05*)

*CDC-A05requires use of accessory cable # 7 607 889 093, available separately.

Handling Compact Discs

Be careful when removing a compact disk after the playback is completed because the disk may be extremely hot.

Do not use non-conventionaldiscs such asheart-shaped,octangonal discs, etc. The player could be damaged.

Do not expose compact discs to direct sunlight or any heat source.

Check all compact discs before playing, and discard cracked, scratched or warped discs.

Wipe dirty or damp discs outward from the centre with a soft cloth.

Do not use any solvents such as commercially available cleaners, antistatic spray, or thinner to clean the compact discs.

Attaching the Front Panel

 

Place the right hand side of the front panel so that the parts

ENGLISH

A of the front panel are engaged with the parts B of the unit

 

as shown below. Then push the left hand side of the front

 

panel until it is securely locked.

 

Detaching the Front Panel

 

Remove the CD from the unit, if any, and turn off the power of

 

the unit.

 

Press the REL to unlock the front panel from the unit. Grasp

 

the front panel as shown below and remove it from the unit.

 

Security

To avoid theft or loss of the front panel, you can inactivate the release button REL by installing the screw provided.

1. Unscrew the bolt marked* at the left front side of the unit. (See diagram above)

2. Attach the front panel.

3. Select a locking screw from the mounting hardware (See page 8) and screw it into the same hole to fasten the front panel.

Notes

Do not press hard on the front panel when affixing it to the unit. No more than light to moderate pressure should be needed.

Make sure there is no dust or dirt on the electrical terminals on the back of the front panel as this could cause intermitent operation or other malfunctions.

E-1

BPV660(EN)_body

1

1/22/02, 10:48 AM

 

Identification of Controls

 

 

 

 

 

 

 

 

 

ENGLISH

Front Panel

 

 

 

 

 

 

LCD Display

 

 

 

 

1

2

3

4

5

6

7

8

9

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

 

 

 

 

 

 

FMlll AMll CDC MANX-BASSlo LOUD TRE

 

 

 

 

 

 

 

 

16

15

14

13

1MUTE/SENS button

Mutes the sound. Switches the seek sensitivity between local and distance.

2AUDIO button

Audio control selector; Bass, Treble, Loudness, X-BASS,Balance, Fader & Level Meter.

3REL button

Releases the detachable front panel.

4Eject button

Ejects the CD. Reset the unit.

5Infrared Sensor (behind acrylic facia)

Permits wireless remote control of AM/FM/CD and CD changer with RC-823credit card style remote.

6LCD Display window

7CD insertion slot

Insert the CD here.

8PWR button

Turns the power of the unit on or off.

9DISPLAY button

Display selector. Display priority setting.Clock adjustment.

10SC/PS button

Scan tuning. Preset scan tuning. Scan play in CD/CDC mode.

11TUN/TRK dial

Used to tune in to the desired station.

E-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17 16

15 14

13

12

11 10

9

8

7

 

12

11

 

 

 

 

 

 

 

 

 

 

 

 

12

PRESET MEMORY button

1

SCAN indicator

 

 

 

 

 

 

 

 

During radio reception :

2

STEREO signal indicator

 

 

 

 

 

 

 

1 - 6

;

For Preset memory

3

DISC/TRACK Number indicator

 

 

 

 

 

 

During CD mode :

4

Main display section

 

 

 

 

 

 

 

 

4/MIX

;

For Mix play (Mix & Mix all during CDC)

5

MIX Mode indicator

 

 

 

 

 

 

 

 

5/RPT

;

For Repeat play

6

RPT Mode indicator

 

 

 

 

 

 

 

 

6/

;

For Pause

7

X-BASSlevelindicator

 

 

 

 

 

 

 

13

CD button

 

 

 

8

R-chLevel Meter

 

 

 

 

 

 

 

 

Selects the operating source (CD, CD changer or AUX).

9

Treble indicator

 

 

 

 

 

 

 

14

BAND button

 

10

LOUD indicator

 

 

 

 

 

 

 

 

Selects the AM/FM band & Travel store.

11 lo(Local)indicator

 

 

 

 

 

 

 

15

DISC SELECT button

12

X-BASS/BASindicator

 

 

 

 

 

 

 

 

Select the desired CD in CDC (CD changer) mode.

13

MAN(Manual tuning) indicator

 

 

 

 

 

16

VOL dial

 

 

 

14

CD Changer indicator

 

 

 

 

 

 

 

 

Adjusts the volume level and audio control.

15

AM/FM indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

16

L-chLevel Meter

 

 

 

 

 

 

 

 

 

 

 

 

 

17

DISC IN indicator

 

 

 

 

 

 

 

Remote Control (Optional)

You can operate your receivers basic AM, FM, CD & CDC features via an optional IR Remote Control. Optional Credit Card type and Steering Wheel mounted remotes are available.

BPV660(EN)_body

2

1/22/02, 10:48 AM

General Operations

Turning the power On/Off

Press the PWR to turn the unit On or Off.

Volume Level Control and Memory

Rotate the VOL dial to adjust the volume.

It is also possible to set turn-onvolume level by following the procedure explained below.

1. Rotate the VOL dial until it is set at the required volume.

Volume up

Volume down

2. Press thePWR for two or more seconds. The power will be switched off and the current volume level recorded.

Muting the sound

Press MUTE / SENS.

The R-ch/L-chLevel Meter flashes.

To restore the previous volume level, press MUTE / SENS again.

Setting the Clock

 

The clock uses a 12-hourdisplay system.

ENGLISH

1.

Turn the ignition key to the ON position.

2.

Press the PWR to turn on the unit.

3.

 

Press and hold the DISPLAY for more than two seconds to

 

 

enter the Clock setting mode.

 

4. Use the following buttons and dial to set the clock. (The blinking section can be adjusted.)

AUDIO

: To activated Hour blink

MUTE / SENS

: To activated Minute blink

 

: Adjust the Hour and minute

5. Press theDISPLAY

momentarily to complete the Clock set-

ting mode.

 

Ignition-offClock Recall

The display will illuminate showing the time and then automatically shut off after 5 seconds.

Press the

DISPLAY

while the ignition switch is in the “ OFF ”

 

position.

 

 

Display Priority Selector

Each time the DISPLAY is pressed, the display window will change as shown below ;

Radio mode

Frequency and Clock.

CD / CDC(CD changer) mode

Elapsed time and Clock.

E-3

BPV660(EN)_body

3

1/22/02, 10:48 AM

 

Adjusting the Sound Characteristics

ENGLISH

1. Press theAUDIO

to select the desired adjustment mode

as follows;

 

 

 

 

BASS 0

 

 

TREBLE 0

 

 

LOUD OFF (LOUDNESS)

 

X-BASS0

 

 

L0 R0 (BALANCE)

R0 F0 (FADER)

LE Lo (LEVEL METER)

2. Rotate the VOL dial to adjust the selected item.

Use the following tables as a guide for adjusting the settings in each mode.

Adjust within 5 seconds after selecting the item. After 5 seconds, the unit returns to previous indication.

Adjustment Range

BASS

BASS –5

 

BASS 5

 

 

 

TREBLE

TREBLE –5

TREBLE 5

 

 

 

LOUDNESS

LOUD OFF

LOUD ON

 

 

 

X-BASS

X-BASS0

X-BASS4

 

 

 

BALANCE

L9 R0(Full left)

L0 R9(Full right)

 

 

 

FADER

R9 F0(Full rear)

R0 F9(Full front)

 

 

 

 

LEVEL METER

OFF

Lo (Normal)

Hi (High)

 

 

 

 

 

Tip

Settings for BASS, TREBLE, LOUDNESS and XBASS can be made to each of the following modes independently:

FM, AM, CD, CD Changer and AUX.

E-4

Enhancing the bass sound

For extended bass centered @ 72Hz, Blaupunkt’s X-BASSfunction can be set for either each band and CD mode.

You can select :

X-BASS1 : Enhanced BASS level (low).

X-BASS2 : Enhanced BASS level (Middle).

X-BASS3 : Enhanced BASS level (High).

X-BASS4 : Enhanced BASS level (Very high).

X-BASS0 : No BASS enhanced.

Press the AUDIO to display the “X-BASS” on the display window. Each time you rotate the VOL dial, the current mode appears on the display window and the mode change as fol-

lows:

X-BASS0 (No display)

X-BASS1

X-BASS2

X-BASS3

X-BASS4

Note

Reduce XBASS level if your combination of speakers and addon amplifiers sound distorted at the preferred sound level.

Level Meter Sensitivity selection

The sensitivity of the level meter display can be switched.

You can select :

• OFF (No indication)

• Low

: Normal (Low) sensitivity.

• High

: High sensitivity.

1. Press theAUDIO to display the “ LE Lo ” on the display window.

2. Rotate the VOL dial to select the desired meter sensitiv-

ity.

: OFF

: Lo

: Hi

Switching the Source (Selecting auxiliary input)

You can connect auxiliary equipment (Portable cassette player, etc) to this radio via optional AUX-INcable. (See page 9)

Each time the

CD

is pressed, the operation source will

 

change over as shown below;

RADIO CD

CD changer or AUX

 

 

 

 

Press the BAND to return to tuner mode.

Note

If the

CD

button is pressed when no CD has been loaded

 

into the unit, The CD mode will skip to the CD changer mode or AUX mode.

Also, if the CD changer is not connected, the system will move across to the AUX mode regardless of whether auxiliary equipment is connected or not (“ AU ” will be displayed.)

It is not possible to switch to the AUX mode when the CD changer is connected.

BPV660(EN)_body

4

1/22/02, 10:48 AM

MUTE / SENS

Radio Reception

Seek Tuning

1. Press theBAND to select the desired AM or FM band. FMI FMII FMIII AMI AMII

(FM III & AMII are Travel Store bands.)

2. Rotate the TUN/TRK dial to tune in stations. Tuning automatically stops at a broadcasting frequency.

When tuned in to FM stereo broadcasting stations, the “” stereo signal indicator will appear on the display window.

: Lower Frequency.

: Higher Frequency.

Manual Tuning

1. Press theBAND to select the desired AM or FM band.

2. Rotate and hold the TUN/TRK dial for more than 0.5 second to activate the manual tuning mode.

“ MAN ” indicator will appear on the display window. Rotate again to tune in to stations.

After 4 seconds of completing Manual Tuning, the tuning control will revert to the Seek Tuning mode.

Scan Tuning

1.

Press the

BAND

to select the desired AM or FM band.

2.

Hold the

SC/PS

pressed for less than 2 seconds.

 

The unit will scan the selected band for stations and the

 

unit will stop at each station for 8 seconds, before con-

 

tinuing to the next station.

 

Press the

SC/PS

again to stop Scan Tuning and remain

 

this on the selected frequency.

Preset Scan Tuning

1.

Press the

BAND

to select the desired AM or FM band.

2.

Hold the

SC/PS

pressed for more than 2 seconds.

The unit will scan preset memory for the 12 stations from the AM I/AMII band or the 18 stations from the FMI/FMII/FMIII bands. The unit will stop at each preset station for 8 seconds, before continuing to the next preset station.

Press the SC/PS again to stop Preset Scan Tuning and remain this on the selected frequency.

Memorizing Stations Automatically

(Travel Store)

1.

Press the

BAND

to select the desired AM or FM band.

2.

Hold the

BAND

pressed for longer than 2 seconds.

Up to 6 stations with strong signals will be automatically stored in preset memory for the selected band.

If the radio is in FM I or FMII, it switches to FMIII. If the radio is in AMI, it switches to AMII.

Note

This function is available for FM III and AMII.

Memorizing Only the Desired Stations

 

 

You can store up to 6 stations on each band (18 for FM I, FM

ENGLISH

II and FMIII, 12 for AMI and AMII) in the order of your

 

choice.

 

 

 

1.

Press the BAND to select the desired band.

 

 

2.

Rotate the TUN/TRK dial to tune in stations.

 

 

3.

Press and hold the desired preset memory button 1

-

 

 

6

for about 2 seconds until the frequency indicator

 

 

 

 

 

flashes twice.

 

 

 

The number of the pressed preset memory button ap-

 

 

pears on the display window.

 

 

Note

If when you store another station on the same preset number button, the previously stored station is replaced with new one.

Receiving the Memorized Stations

1.

Press the

BAND

to select the desired AM or FM band.

2.

Press the

1 -

6 momentarily.

Local/Distant (LO/DX) Selection

This feature is used to select the signal strength at which the radio will stop during Seek Tuning.

Press the for more than 2 seconds to select the Local setting and only strong (local) stations will be received. The “ lo ” indicator appears on the display window.

Pressing for more than 2 seconds again will select the Distant setting and the radio will stop at a wider range of signals, including weaker more distant stations. The “ lo ” indicator will go out on the display window. DX is the suggested default setting.

E-5

BPV660(EN)_body

5

1/22/02, 10:49 AM

CD Operations

ENGLISH

Playing the CD player

Loading Discs

 

 

Insert the disc into the CD insertion slot with the labeled side

 

facing up.

 

Playback begins automatically.

 

Labeled side up

Stopping Playback

Press the BAND to select the radio reception (FMI, FMII, FMIII or AMI, AMII).

Ejecting Discs

Press the to eject the disc.

Notes

The unit will turn on automatically when a CD is inserted if the ignition switch is ‘‘ON’’.

When the disc is ejected from the CD slot, remove it within 10 seconds; otherwise, the disc will be reloaded automatically.

Scan Play

Press the SC/PS during CD mode.

The ‘‘ ’’ indicator appears in the display window. This will play the first 10 seconds of all the tracks on the disc. Press theSC/PS again to cancel this feature.

Repeat Play

Press the 5/RPT during CD mode.

The ‘‘ ’’ indicator appears in the display window and the current track is played repeatedly.

Press the 5/RPT again to cancel this feature.

Mix Play

NEVER Insert a 3-inchCD!

This unit is designed for playback of standard 5-inchCD’s only. Do not attempt to use3-inchCD singles in this unit, either with or without an adaptor, as damage to the player and/or disc may occur.

Tips

• When a CD is loaded, the on the display remains lit.

Listening to a disc that is already loaded

Press the

CD

to select the CD mode.

 

Playback begins automatically.

Pausing Playback

Press the

6/ .

 

To resume playback, press the 6/ again.

Track Search

Rotate the TUN/TRK dial during CD mode. Track numbers appear in the display window.

:Playback starts from the beginning of the

current track. Rotate again to play the previous track.

: Playback starts from the beginning of the next track.

Cue / Review

Rotate and hold the TUN/TRK dial. Release when you have found the desired point.

: To search backward.

Press the 4/MIX during CD mode.

The ‘‘ ’’ indicator appears in the display window.

All the tracks on the current disc are played in random order. Press the 4/MIX again to cancel this feature.

: To search forward.

E-6

BPV660(EN)_body

6

1/22/02, 10:49 AM

CD Changer Controls

Playing the CD Changer

This product can control a CD changer. Please check with your nearest car stereo specialist for recommendations of the models that will work with this radio (See page 1).

Press the

CD

to switch the CD changer mode. DISC and

 

TRACK are displayed. The disc no., track number no., and time are indicated in the display window and playback begins automatically. Press again to change back to built-inCD operation.

Disc Select

Press the Disc select buttons to select the desired disc for play.

2

:

To advance to a higher number disc.

1

:

To return to a lower number disc.

Track Search

Rotate the TUN/TRK dial.

Track numbers appear in the display window.

: Playback starts from the beginning of the current track. Rotate again to play the previous track.

:Playback starts from the beginning of the next track.

Cue / Review

Rotate and hold the TUN/TRK dial. Release when you have found the desired point.

: To search backward.

: To search forward.

Track / Disc Scan Play

Track Scan

 

Press the

SC/PS .

 

The ‘‘

’’ indicator appears in the display window. This

will play the first 10 seconds of all the tracks on the disc.

Press the

SC/PS

again to cancel this feature.

Disc Scan

 

 

Press the

SC/PS

for more than 2 seconds.

The ‘‘

’’ indicator appears in the display window. This

will play the first 10 seconds of the first track on each disc.

Press the

SC/PS

again to cancel this feature.

Track / Disc Repeat Play

Track Repeat

 

Press the

5/RPT .

 

The ‘‘

’’ indicator appears in the display window and the

current track is played repeatedly.

Press the

5/RPT

again to cancel this feature.

Disc Repeat

 

Press the

5/RPT

for more than 2 seconds.

The ‘‘

’’ indicator appears in the display window and the

current disc will be continually repeated.

Press the

5/RPT

again to cancel this feature.

Track / Disc Mix Play

Track Mix

 

 

Press the

4/MIX .

 

The ‘‘

 

 

’’ indicator appears in the display window.

 

 

All the tracks on the current disc are played in random order.

Press the

4/MIX

again to cancel this feature.

Disc Mix

 

 

Press the

4/MIX

for more than 2 seconds.

 

’’ indicator appears in the display window.

The ‘‘

 

 

 

Both discs and tracks will be played in random order. Press the 4/MIX again to cancel this feature.

ENGLISH

E-7

BPV660(EN)_body

7

1/22/02, 10:49 AM

Installations

Supplied Mounting Hardware

 

ENGLISH

 

 

 

 

Sleeve

Bushing,

Locking

Mounting Strap

Release

Screw

screw

and Screw

Keys

 

Precautions

Be sure to detach the front panel before you start installing the unit.

Choose the mounting location carefully so that the unit will not interfere with the normal driving operations of the driver.

Use only the supplied mounting hardware for a safe and secure installation.

When mounting the unit in a car, keep the unit as level as possible. If the unit must be mounted at an angle, due to the design of the vehicle, make sure that the unit does not tilt upward by more than 30°.

E-8

Mounting Example

Installation in the dashboard.

1. Install the sleeve in the dashboard.

2. Select and bend the appropriate tabs to hold the sleeve firmly in place.

Mounting Strap Use

3. Attaching the Mounting Strap to the underside of the dash board, using screw.

Attach the back of the unit to the Mounting Strap using the support stem bolt and hardware.

Fire wall

Bushing Use

3. As shown in the figure below, securely fasten the screw, which has been inserted into the bushing to the rear of the set.

Fire wall

The distance to the fire wall varies due to the type of the car. Be sure to secure the unit by properly inserting the bushing.

Caution

Insufficient fastening of the screw may cause some CD’s to skip.

* Warning

Failure to properly install the Mounting Strap or rear support Bushing is a major cause of CD skipping. Without these securing devices, the chassis of the CD receiver is able to move up & down whenever the road has imperfections and CD skipping results.

Note

Some Japanese/Asian vehicles such as TOYOTA & NISSAN do not require use of the sleeve and trim ring assembly.

To secure the replacement radio use the O.E.M. brackets and mounting screws. These brackets will align with the threaded screw holes found on each side of the new radio.

BPV660(EN)_body

8

1/22/02, 10:49 AM

Connections

Warning

To prevent short circuit, remove the key from the ignition and disconnect the battery’s (–)terminal.

This unit is designed for negative ground 12 V DC operation only. You can not use it for 24 V or other types of car batteries.

Connection procedure

Caution

DO NOT connect any speaker wires to the metal body or chassis of the vehicle.

DO NOT connect the speaker common (–)wires to each other.

Connect each speaker wire directly to each speaker terminal.

All speaker common (–)wires must remain floating.

ie. No common connections or connection to vehicle grd.

Connect each pair of speaker leads only to a single speaker (or speaker system) that has an impedance of least 4 ohms, as well as 57.5-wattpower-handlingcapability.

Do not connect speaker leads to any inputs on external amplifiers. This will cause damage to the internal amplifier of this unit.

1Make sure the car’s ignition key has been removed.

2Disconnect the negative (–)terminal of the car’s battery.

3Connect the wiring harness wires in the following order : Ground wire (Black), +12V Constant Power Supply (Yellow), +12V Accessory/Switched (Red) and Power Antenna/Amplifier Turn On (Blue), and tape each so they do not come in contact with each other.

4Connect the speaker wires of the wiring harness.

5Connect the car’s antenna terminal to the antenna socket of the unit.

6Connect the detachable wire harness to the unit.

7Reconnect the negative (–)terminal of the car’s battery.

8Start the car’s engine.

9Make sure the unit operates properly.

Connection procedure

ENGLISH

For connection to optional CD changer. Requires cable adapter # F00E500029.

 

To use AUX input instead of CD changer, please order part number 7 607 897 093

 

in addition to F00E500029.

 

Preamp Out/Line Out Connections

• Since this unit has Line Level Outputs, you can use an amplifier to upgrade your vehicle stereo system.

RCA Line-outJacks

White (Left)

Red (Right)

External Amplifier

Rear Speaker

RCA Line-outJacks (For Rear Speakers)

Connect a patch cable (not supplied) from the White (left rear channel) and Red (right rear channel) RCA line output jacks of the unit to the line input terminals of the external amplifier.

E-9

BPV660(EN)_body

9

1/22/02, 10:49 AM