RCA RC46 User Manual

0 (0)

v1.0 (EN/F)

user manual guide de l’utilisateur

RC46

	AUX
AM
FM PM	MHz
AM	kHz

EN/F

It is important to read this user manual prior to using your new product for the ﬁrst time.

Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau produit pour la première fois.

FCC information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Service information

This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty included in this user manual.

For your records

In the event that service should be required, you may need the model number and the serial number. In the space below, record the date and place of purchase and the serial number: Model No.:

Date of Purchase:

Place of Purchase: Serial No.:

Technical information

Product: Clock Radio Brand: RCA

Model: RC46

Electrical consumption

Power Supply: 120V ~ 60Hz Power Consumption: 6 Watts

SEE MARKING ON BOTTOM OF PRODUCT

WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Before you begin

Plugging in for power

AC OUTLET POWER SUPPLY: 120V~60Hz

Refer to the “Clock” section and follow the instructions to get the clock time shown correctly with the Auto Clock set feature.

Battery back-up operation

•This clock radio is equipped with a memory holding system that can be powered with 2 “AA” batteries (included). The power failure protection circuit will not operate unless battery is installed.

•When normal household power is interrupted, or AC line cord is unplugged, the batteries will power the clock radio to keep track of time and alarm settings programmed into memory.

•When the battery backup functions, the digital display will not light, however, the function of alarm

still occurs during the power interruption if remaining battery power is adequate.

•Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm.

To install batteries:

1.Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet.

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Manufacturer/Responsible Party

Audiovox Electronics Corp.,

150 Marcus Blvd., Hauppauge,

NY 11788

PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE

IMPORTANT SAFETY INSTRUCTIONS

Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use.

•Read these instructions.

•Keep these instructions.

•Heed all warnings.

•Follow all instructions.

•Do not use this apparatus near water.

•Clean only with dry cloth.

•Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

•Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

•Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

•Only use attachments/accessories speciﬁed by the manufacturer.

• Use only with the cart,
stand, tripod, bracket,	]
or table speciﬁed by
the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

•Unplug this apparatus during lightning storms or when unused for long periods of time.

•Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

ADDITIONAL SAFETY INFORMATION

•Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely.

•Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases, shall be placed on the apparatus.

•Always leave sufﬁcient space around

the product for ventilation. Do not place product in or on a bed, rug, in a bookcase or cabinet that may prevent air ﬂow through vent openings.

•Do not place lighted candles, cigarettes, cigars, etc. on the product.

•Connect power cord only to AC power source as marked on the product.

•Care should be taken so that objects do not fall into the product.

•Do not attempt to disassemble the cabinet. This product does not contain customer serviceable components.

•IF YOUR PRODUCT OPERATES ON BATTERIES, adhere to the following precautions:

A.Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, or if all batteries are not replaced at the same time.

B.Any battery may leak electrolyte or explode if disposed of in ﬁre

or an attempt is made to charge a battery not intended to be recharged.

C.Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury. When discarding batteries, be sure to dispose of them in

the proper manner, according to your state/provincial and local regulations.

D. Do not expose batteries to excessive heat (for example, by leaving them in sunlight or close to ﬁre).

•The marking information is located at the bottom of apparatus.

•Caution marking is located at bottom of apparatus.

Important Battery Precautions

•Any battery may present a risk of ﬁre, explosion, or chemical burn if abused. Do not try to charge a battery that is not intended to be recharged, do not incinerate, and do not puncture.

•Non-rechargeable batteries, such as alkaline batteries, may leak if left in your product for a long period of time. Remove the batteries from the product if you are not going to use it for a month or more.

•If your product uses more than one battery, do not mix types and make sure they are inserted correctly.

Mixing types or inserting incorrectly may cause them to leak.

•Discard any leaky or deformed battery immediately. They may cause skin burns or other personal injury.

•Please help to protect the environment by recycling or disposing of batteries according to federal, state, and local regulations.

2.Insert 2 AA batteries (included).

3.Replace the compartment door.

Note: we recommend that you replace the batteries every year.

Power failure indicator

When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless batteries are installed). After AC power is restored (reconnected), the Digital Display will blink to indicate that power was

interrupted and you should readjust the time and alarm settings.

Power is fed to the unit even when it is not functioning. To cut the power supply off, the

power cable must be unplugged.

General controls

Wake 1 mode

Large display: Clock time or radio frequency

		AUX
	AM
FM	PM	MHz
AM		kHz
	Small display: Wake time

Wake 2 mode

Front view

SNOOZE – enter snooze mode where the alarm will quiet but sound again once the snooze period is over.

RADIO – turn on the radio.

REV – set clock or wake time (decrease value).

FWD – set clock or wake time (increase value).

OFF – turn off the unit.

CHECK WAKE TIME – check the currently set wake time.

–VOLUME+ – adjust volume.

TUNING – select radio frequencies.

Back view

BRIGHTNESS – select display brightness (high or low).

DST – turn daylight saving function on or off.

TIME ZONE – press repeatedly to select a time zone

BAND – select between AM and FM bands.

Top view

SLEEP – activate sleep function.

/WAKE1/WAKE2/ – slide switch to set Wake 1, Wake 2 and clock time.

WAKE –OFF – activate and set wake function.

Clock

Auto clock set

You do not have to set the clock time as a built-in automatic time set system is equipped in this clock powered by 2 AA batteries (included and installed).

To set the clock time correctly: 1. Plug for power

• Insert the plug of the unit into an AC power outlet.

2. Select daylight saving

• Slide the DST switch at the back of the unit to turn on/ off in areas observing/not observing such time change.

3. Select your time zone

• Press TIME ZONE repeatedly at the back of the unit to cycle through the time zones (EST > CST

>MST > PST > AKST > HST > AST

>EST...). The default time zone is Eastern (EST) (refer to the maps on the right).

Your clock is now set and ready for use.

WARNING: Please avoid playing with these buttons after entering the Clock/ Alarm set mode.

Setting clock manually

1.Slide the switch /WAKE1/

WAKE2/ on the top of the unit to clock position.

2.Press REV or FWD to set the clock time. The time decrements or increments will follow by a faster

rate when you press and hold the buttons.

•The “:” between hour and minute time ﬂashes when you are setting the time. AM or PM icon will also show beside the time.

3.Slide the switch /WAKE1/

WAKE2/ on the top of the unit to lock position when ﬁnished.

Wake function

Turning off the wake alarm or radio

•To silence the wake function momentarily:

To turn off the wake function, press SNOOZE on the top of the unit. The wake alarm or radio will be switched off temporarily. The alarm or radio will be on again when the snooze period (default: 9 minutes) is over. (read “SmartSnoozeTM”)

•To turn off the wake alarm or radio:

Press OFF. The wake alarm or radio will activate again the next day unless you switch off the Wake function.

•To disable the wake function

completely:

Press WAKE – OFF 1 or 2 repeatedly on the top of the unit

until no wake mode icon (1 , 1 or 2 , 2 ) shows on the large display.

SmartSnoozeTM

This operation allows extra sleep time after the wake function is on. The alarm will be off by pressing SNOOZE, SLEEP, WAKE –OFF 1, or 2 until the snooze period is over. Snooze function can be used repeatedly up to 60 minutes. After this, the wake function will turn off until the next day.

To set the “quiet” period:

1.Press and hold SNOOZE.

2.Press REV or FWD to set the quiet period that shows on the large display. The time decrements or increments will follow by a faster

rate when you press and hold the buttons.

•Snooze period can be set from 1 to 30 minutes (default: 9 minutes).

3. Release SNOOZE.

SmartSnoozeTM is only available when

/WAKE1/WAKE2/ is at the lockposition.

US time zones

Seattle

Olympia

Washington

Montana

North Dakota

Maine

Salem

Helena

Augusta

Bismarck

Oregon

Idaho

Minnesota

Montpelier

N.H.

St. Paul

Vt.

Concord

Boise

South Dakota

Albany

Boston

Wisconsin

Michigan

New York

Mass. Providence

Wyoming

Pierre

HartfordR.I.

Madison

Lansing

Detroit

Pennsylvania

Conn.

New York

Alaska

Nevada

Salt Lake City

Lincoln

Iowa Chicago

Indiana Ohio

Philadelphia

Trenton

Des Moines

Md.

Delaware

Sacramento Carson City

Cheyenne

Nebraska

Harrisburg

New Jersey

(AKST)

San Francisco

Utah

Illinois

Columbus

West

Annapolis

Denver

Springfield

Indianapolis

Virginia

Washington, D.C.

Colorado

Topeka

St. Louis

Charleston

Virginia

California

Kansas

Jefferson City

Frankfort

Las Vegas

Missouri

Kentucky

Raleigh

Summer

Winter

Nashville

North Carolina

Los Angeles

Santa Fe

Arizona

Oklahoma

Tennessee

Oklahoma City

Memphis

Columbia

Phoenix

New Mexico

Arkansas

South

Little Rock

Atlanta

Carolina

Hawaii-

Mississippi

Alabama Georgia

Dallas

Jackson

Montgomery

Aleutian

Texas

Louisiana

Austin

Baton

(HST)

Rouge

Houston

New Orleans

Florida

Miami

Puerto Rico

Pacific Mountain

Central

Eastern

Atlantic

(PST)

(MST)

(CST)

(EST)

(AST)

Canadian time zones

Yukon

Territory

Northwest Territories

Nunavut

British

Columbia

Newfoundland

Summer

Winter

Alberta

Manitoba

Saskatchewan

Quebec

Saskatoon

Ontario

Regina

Winnipeg

Pacific

Mountain

Central

Eastern

Atlantic

(PST)

(MST)

(CST)

(EST)

(AST)

Radio

Selecting radio mode

Press RADIO to switch on radio.

Switching band

Slide the BAND switch on the back of the unit to select FM or AM band.

Tuning the radio

Rotate the TUNING knob on the right of the unit to adjust the radio frequency that shows on the large display.

Built-in AFC

The Built In Automatic Frequency Control (AFC) works only on FM. It helps reducing drift on FM reception and keeping the radio locked in on the FM station to which it is tuned.

Brightness control

Slide BRIGHTNESS switch on the back of the unit to Hi (high) or Lo (low) position to adjust the brightness of all the displays at the front of the unit.

Sleep function

In sleep mode, you can set the duration (up to 90 minutes) before the radio turn off automatically.

To set the sleep mode:

•Press SLEEP repeatedly to cycle among the sleep times available (90min, 60min, 30min, 15min and OFF. 90min is the default setting) on the large display.

•The radio will be switched on.

To check the remaining time in sleep mode:

•Press and hold SLEEP to check the remaining sleep time on the large display.

To cancel the sleep mode:

•If you decide to turn off the unit sooner, press SNOOZE or OFF.

Warranty information

12 Month Limited Warranty Applies to RCA Audio/Video Products

AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company’s option) without charge for parts and repair labor.

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), speciﬁcation of defect(s),

transportation prepaid, to the Company at the address shown below.

This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, loss/interruptions of broadcast or internet service, to costs incurred for installation, removal or reinstallation of product, to corruptions caused by computer viruses, spyware or other malware, to loss of media, ﬁles, data or content, or to damage to tapes, discs, removable memory devices or cards, speakers, accessories, computers,

computer peripherals, other media players, home networks or vehicle electrical systems.

This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or

When tuning in FM stations, you may notice that the station you are tuning can be well-tuned on two or three nearby points on the dial. Always tune carefully at the loudest and clearest point.

AM antenna

A built-in ferrite rod antenna eliminates the need for an outside antenna for AM reception. Rotating the unit slightly may improve reception of distant AM stations.

representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you speciﬁc legal rights and you may also have other rights which vary from state to state.

How to make a warranty claim:

•If your product is capable of storing content (such as an mp3 player, digital voice recorder, etc), it is recommended to make periodic backup copies of content stored

on the product. If applicable, before shipping a product, make a back up copy of content or data stored on the device. Also, it is advisable to remove any personal

content which you would not want exposed to others. IT IS LIKELY THAT CONTENTS AND DATA ON THE DEVICE WILL BE LOST DURING SERVICE AND REFORMATTING. AUDIOVOX ACCEPTS NO LIABILITY FOR LOST CONTENT OR DATA,

OR FOR THE SECURITY OF ANY PERSONAL CONTENT OR DATA ON THE RETURNED DEVICE. Product will be returned with factory

Wake function

Setting wake time

This unit allows two wake times to be set.

1.Slide the switch /WAKE1/ WAKE2/ on the top of the unit to WAKE 1 or WAKE 2 position.

2.Press REV or FWD to set the respective wake time. The time decrements or increments will follow by a faster rate when you

press and hold the buttons.

•The wake time, corresponding wake timer indicator (WK-1 for WAKE 1 and WK-2 for WAKE 2) and AM/ PM time indicator ﬂash on the small display.

3.Slide the switch /WAKE1/

WAKE2/ on the top of the unit to position when ﬁnished.

Selecting wake source

You may be woken up by radio or alarm.

1.Select an AM or FM station (see directions on “Radio”).

2.Set a wake time (see above direction).

3.Press WAKE – OFF 1 or 2

repeatedly on the top of the unit to select a waking mode.

•Corresponding icon lights on the large display.

default settings, and without any pre-loaded content which may have been installed in the originally purchased products. Consumer will be responsible for reloading data and content. Consumer will be responsible to restore any personal preference settings.

•Properly pack your unit. Include any remotes, memory cards, cables, etc. which were originally provided with the product. However DO NOT return any removable batteries, even if batteries were included with the original purchase. We recommend using the original carton and packing materials.

•Include evidence of purchase date such as the bill of sale. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to:

Audiovox Electronics Corp. Attn: Service Department. 150 Marcus Blvd., Hauppauge N.Y. 11788

1-877-833-3491

•Insure your shipment for loss or damage. Audiovox accepts no liability in case of damage or loss en route to Audiovox.

•Pay any charges billed to you by the Exchange Center for service not covered by the warranty.

1 – Wake 1 by alarm

1 – Wake 1 by radio

2 – Wake 2 by alarm

2 – Wake 2 by radio

•The unit equips with GRAD-U- WAKE feature, the alarm tone volume will increase gradually to its maximum in about 30 to 45 seconds.

Checking wake time

•Press CHECK WAKE TIME repeatedly to show the currently set wake time 1 and 2.

•The wake time, corresponding wake timer indicator (WK-1 for WAKE 1 and WK-2 for WAKE 2) and AM/ PM time indicator show on the small display.

•If corresponding wake function is not activated, OFF shows on the small display.

•A new or refurbished unit will be shipped to you freight prepaid.

What we will do:

Provide you with a new, or at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product’s warranty period.

For Canada Customers, please ship to:

Audiovox Return Centre c/o Genco

6685 Kennedy Road, Unit#3, Door 16, Mississuaga, Ontario L5T 3A5

The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not as a guarantee. In order to provide you with the highest quality product, we may make changes or modiﬁcations without prior notice.

Marca(s) ® Registrada(s) www.rcaaudiovideo.com Printed in China