Specification*
General |
|
Power Supply |
DC 12V (11V - 16V), |
|
Test Voltage 13.2V |
|
Negative Ground |
Current Consumption |
Less than 3.0A at 0.5W |
Maximum Power Output |
|
<CQ-YH5070L/5072L/5074A> |
30W×4ch |
<CQ-YH5071L> |
20W×4ch |
Output Impedance |
4Ω |
LW/MW Radio |
|
Frequency Range |
: |
<LW Band> |
153 - 279kHz |
<MW Band> |
531 - 1,611kHz |
Usable Sensitivity |
28dB/µV (S/N 20dB) |
Signal to Noise Ratio |
More than 42dB |
ORDER No. 0149
AUTOMOTIVE ELECTRONICS
HONDA CQ-YH5070L/5071L CQ-YH5072L/5074A
LW/MW/UKW MPX ELECTRONIC TUNING RADIO with Cassette Player
HONDA PART No. (CQ-YH5070L): 39100-S6A-G100
HONDA PART No. (CQ-YH5071L): 39100-S6A-G000
HONDA PART No. (CQ-YH5072L): 39100-S6A-E102
HONDA PART No. (CQ-YH5074A): 39100-S5A-G100
VEHICLE : CIVIC
DESTINATION : EUROPE
PRODUCED AFTER (CQ-YH5070/5072L) : Nov., 2000 PRODUCED AFTER (CQ-YH5071L) : Feb., 2001 PRODUCED AFTER (CQ-YH5074A) : Dec., 2000 <NOTE>
For the unit ID CODE, please refer to next page.
UKW Stereo Radio |
|
Frequency Range |
87.5 - 108.0MHz |
Usable Sensitivity |
6dB/µV (S/N 30dB) |
Seek Sensitivity |
28dB/µV |
Stereo Separation |
More than 20dB |
Dimensions** (W×H×D) |
180×52×160mm |
Weight** |
1.4kg |
*Specifications and the design are subject to possible modification without notice due to improvements.
**Dimensions and Weight shown are approximate.
Doldy noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
“Dolby” and the double-D symbol 
are trade marks of Dolby Laboratories Licensing Corporation.
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
CONTENTS
|
|
Page |
|
|
Page |
1 |
ID CODE |
2 |
10 |
ALIGNMENT POINTS |
10 |
2 |
FEATUERS |
2 |
11 |
REPLACEMENT PARTS LIST |
11 |
3 |
REAR VIEW |
2 |
12 |
EXPLODED VIEW (Unit) |
17 |
4 |
FRONT VIEW AND FUNCTIONS |
3 |
13 |
TAPE PLAYER PARTS |
18 |
5 |
WIRING CONNECTIONS |
4 |
14 |
EXPLODED VIEW (Tape Deck) |
20 |
6 |
BLOCK DIAGRAM |
5 |
15 |
WIRING DIAGRAM |
21 |
7 |
TERMINALS DESCRIPTION |
6 |
16 |
SCHEMATIC DIAGRAM (1) |
27 |
8 |
PACKAGE AND IC BLOCK DIAGRAM |
7 |
17 |
SCHEMATIC DIAGRAM (2) |
29 |
9 |
ALIGNMENT INSTRUCTIONS |
10 |
|
|
|
1 ID CODE 3 REAR VIEW
±CQ-YH5070L : 1SC0
±CQ-YH5071L : 1CC0
±CQ-YH5072L : 1SC1
±CQ-YH5074A : 1SC3
2FEATUERS
±PLL (Phase Locked Loop) synthesized tuning.
±24-station preset (6-LW, 6-MW, 12-UKW)
±Scan Tuning.
±Cassette Tape Player Control.
±CD/MD player Control.
±CD/MD changer control.
±Electronic sound control function.
±GA-NET control function.
2
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
4 FRONT VIEW AND FUNCTIONS
3
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
5 WIRING CONNECTIONS
4
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
6 BLOCK DIAGRAM
5
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
7 TERMINALS DESCRIPTION
7.1.Main Block
IC601 : C2CBJG000156
Pin No. |
Port |
Description |
I/O |
(V) |
1 |
AMP-MUTE |
Power amp mute |
O |
0 |
2 |
NAVI-L-MUTE |
Not used |
- |
- |
3 |
MUTE |
Mute output |
O |
0 |
4 |
AMP-ON |
Power Amp stand-by |
O |
4.9 |
5 |
FL-MUTE |
Front speaker Lch mute |
O |
4.9 |
6 |
FR-MUTE |
Front speaker Rch mute |
O |
4.9 |
7 |
REAR-MUTE |
Rear speaker mute |
O |
4.9 |
8 |
SYS-ACC |
System ACC on |
O |
0 |
9 |
NAVI-R-MUTE |
Not used |
- |
- |
10 |
ACC CNT |
ACC 5V power on/off |
O |
0 |
11 |
RESET |
Reset input |
I |
4.9 |
12 |
XT2 |
Crystal oscillator terminal |
- |
2.5 |
13 |
XT1 |
Crystal oscillator terminal |
- |
2.3 |
14 |
VSS |
Ground |
- |
0 |
15 |
X2 |
Crystal oscillator terminal |
- |
2.1 |
16 |
X1 |
Crystal oscillator terminal |
- |
2.0 |
17 |
REGOFF |
(Connecting to ACC5V) |
- |
4.9 |
18 |
REGC |
(Connecting to ACC5V) |
- |
4.9 |
19 |
VDD |
+5V power supply |
- |
4.9 |
20, 21 |
NC |
No connection |
- |
- |
22 |
MS |
MS detection |
I |
0 |
23 |
MS(PL/FF) |
MS mode selection |
O |
0 |
24 |
T.LOAD |
Tape loading detection |
I |
0 |
25 |
DOLBY |
Dolby NR on/off |
O |
0 |
26 |
F/R |
Tape head change |
O |
0 |
27 |
EQ(MTL) |
Metal tape mode selection |
O |
4.9 |
28 |
A/B |
Tape side detection |
I |
0 |
29 |
MSM |
MS gain contrl |
O |
4.9 |
30 |
T.IN |
Tape-in detection |
I |
0 |
31 |
LCD ON |
LCD illumi. on/off |
O |
4.9 |
32 |
LCD-CE |
LCD driver enable |
O |
0 |
33 |
LCD-CLK |
Shift clock for LCD data |
O |
0 |
34 |
LCD-DI |
LCD data |
O |
5.1 |
35 |
LCD-DO |
LCD data |
I |
4.7 |
36 |
SD/VCONT |
(ground pull-down) |
- |
0 |
37 |
M2F |
Main motor control |
O |
0 |
38 |
CA.PON |
Tape power control |
O |
4.7 |
39 |
CM.PON |
Tape power control |
O |
4.6 |
40 |
VSS |
Ground |
- |
0 |
41 |
VDD |
+5V power supply |
- |
4.9 |
42 |
M2 |
Main motor control |
O |
0 |
43 |
M1-2 |
Loading motor control |
O |
0 |
44 |
M1-1 |
Loading motor control |
O |
0 |
45 |
BIT1 |
Tape mode switch |
I |
4.6 |
46 |
A.END |
Tape end signal |
I |
1.5 |
47 |
B.END |
Tape end signal |
I |
2.4 |
48 |
BIT2 |
Tape mode switch |
I |
4.6 |
49 |
EQ |
Metal/Normal switchl |
I |
0 |
50 |
BIT3 |
Tape mode switch |
I |
0 |
51 |
CLOCK |
(+5V pull-up) |
- |
4.9 |
52 |
POWER |
Power switch I |
4.9 |
|
53 |
SEC-LED |
Security LED on/off |
O |
4.9 |
54 |
TEL-MUTE |
Telephon mute |
I |
0 |
55 |
AM/FM |
AM/FM selection |
O |
4.9 |
56 |
R.ON |
Radio power on/off O |
4.9 |
|
57 |
SEC2 |
(Ground pull-down) |
- |
0 |
58 |
SEC-CS |
Security ROM chip select |
O |
0 |
59 |
SEC-CLK |
Shift clock for security ROM |
O |
0 |
60 |
SEC-DI |
Serial data |
I |
1.0 |
61 |
SEC-DO |
Serial data |
O |
0 |
62 |
NC(ASTB) |
(Ground pull-down) |
- |
- |
63 |
REMO |
(Ground pull-down) |
- |
0 |
64 |
3/4 |
(Ground pull-down) |
- |
0 |
65 |
RDS-CLK |
Shift clock for RDS data |
I |
2.5 |
66 |
RDS-DATA |
RDS data |
I |
2.5 |
67 |
SEC-SEL |
(Ground pull-down) |
- |
0 |
68 |
RMODE |
Radio mode |
O |
4.9 |
69 |
SD.ST |
FM stereo detection |
I |
4.9 |
70 |
AREA SEL |
Ground pull-down) |
- |
0 |
71, 72 |
NC |
No connection |
- |
- |
73 |
TESTMODE |
(Connecting to ground) |
- |
0 |
74 |
VSM |
Phase diff. level detection |
I |
0 |
75 |
MP |
FM tuner multipass |
I |
0 |
76 |
NOISE |
Adjustment station detection |
I |
0 |
77 |
REMOCON |
Not uesd |
- |
- |
78 |
RDS-MUTE |
RDS mute |
O |
4.9 |
79 |
TEST |
(+5V pull-up) |
- |
5.0 |
80 |
VOL CLK |
Electronic volume clock |
O |
0 |
81 |
VOL DATA |
Electronic volume data |
O |
0 |
82 |
AVDD |
+5V power supply |
- |
4.9 |
83 |
AVREF1 |
Analog reference voltage |
I |
4.8 |
84 |
AVSS |
Ground |
- |
0 |
85 |
LAN-IN |
LAN data input |
I |
0 |
86 |
LAN-OUT |
LAN data output |
O |
0 |
87 |
NC |
(Connecting to ground) |
- |
0 |
88 |
VOL-A |
Rotary encoder data |
I |
5.0 |
89 |
VOL-B |
Rotary encoder data |
I |
5.0 |
90 |
BAT-DET |
Battery level detection |
I |
4.9 |
91 |
VOL-C |
Rotary encoder data |
I |
0.9 |
92 |
ACC-DET |
ACC level detection |
I |
4.9 |
93 |
EJECT |
Tape eject SW |
I |
4.6 |
94 |
VOL-D |
Rotary encoder data |
I |
0.9 |
95 |
PLL-DO |
PLL data |
O |
0 |
96 |
PLL-CLK |
Shift clock for PLL data |
O |
0 |
97 |
PLL-DI |
PLL data |
I |
5.1 |
98 |
PLL-CE |
PLL chip select |
O |
0 |
99 |
BEEP |
Beep output |
O |
0 |
100 |
P.CONT |
System power on/off |
O |
4.9 |
Note :
Voltage measuerments are with respect to ground, with a voltmeter (Internal resistance : 10M ohms.)
7.2.Display Block
IC901 : YEAMLC75854
Pin No. |
Port |
Description |
I/O |
(V) |
1-6 |
P1-6 |
Not used |
- |
- |
7-39 |
S33-1 |
LCD segment data |
O |
2.5 |
40-43 |
COM1-4 |
LCD common |
O |
2.5 |
44-47 |
KS1-4 |
Key strobe |
O |
0.9 |
48,49 |
KS5,6 |
Not used |
- |
- |
50-53 |
KI1-4 |
Key data |
I |
0 |
54 |
KI5 |
Not used |
- |
- |
55 |
TEST |
(Connecting to ground) |
- |
0 |
56 |
VDD |
+5V power supply |
- |
5.1 |
57 |
VDD1 |
LCD angle |
- |
3.3 |
58 |
VDD2 |
LCD angle |
- |
1.7 |
59 |
VSS |
Ground |
- |
0 |
60 |
OSC |
Oscillator terminal |
- |
3.9 |
61 |
DO |
Key data output |
O |
4.4 |
62 |
CE |
LCD driver chip enable |
I |
0 |
63 |
CL |
Shift clock for LCD data |
I |
0 |
64 |
DI |
LCD data input |
I |
0 |
6
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
8 PACKAGE AND IC BLOCK DIAGRAM
PK50 : YEAU03340E02
IC204 : C1BB00000284
IC250 : C1BA00000332
7
HONDA / CQ-YH5070L/5071L / CQ-YH5072L/5074A
IC461 : YEAMAA6759TT
IC471 : YEAMLC72146T
IC604 : MN1382KTX
IC605 : YEAMH12187ER
8
Loading...