Loading...
Operating Instructions
<Basics>
Remote Camera Controller
Model No. AW RP120G
zz Die Bedienungsanleitung in Deutsch ist als PDF Datei in der CD ROM enthalten. (Seite 2) zz Le mode d’emploi en français est fourni sous forme de fichier PDF sur le CD ROM. (page 2) zz Le istruzioni per l’uso in italiano sono contenute in un file PDF sul CD ROM. (pagina 2)
zz Las instrucciones de funcionamiento en español se encuentran en un archivo PDF del CD ROM. (página 2) zz Документ Инструкция по эксплуатации на русском языке находится в виде PDF файла на диске CD ROM.
(стр. 2)
REMOTE |
CAMERA |
|
|
|
|
CONTR |
|
|
|
|
|
OLLER |
|
|
|
|
|
AW- |
|
|
|
|
|
|
|
|
|
|
RP120 |
Before operating this product, please read the instructions carefully and save this manual for future use.
How the Operating Instructions are configured
<Basics> (this manual):
This <Basics> describes the procedure for connection with the required equipment and for installation. Before installing this unit, be sure to take the time to read through <Basics> to ensure that the unit will be installed correctly.
This manual <Basics> is also contained as a PDF file on the CD ROM supplied with the unit. (page 2)
<Operations and Settings>:
The <Operations and Settings> describes how to operate the unit and how to establish its settings. The <Operations and Settings> is contained as a PDF file on the CD ROM supplied with the unit. (page 2)
ENGLISH
M1212HO0 -FJ |
VQT4T93(E) |
ENGLISH
ppHow to open the operating instruction manual PDF files
Discontinue installation if the installation screen of the software opens as a result of inserting the CD ROM. When [INDEX.pdf] on the CD ROM is opened, a list of the operating instruction manuals will be displayed.
Click on the document name of the manual to be opened.
ppAdobe® Reader® is required to read PDF files.
It can be downloaded from the home page of Adobe Systems.
DEUTSCH
ppÖffnen der PDF Dateien der Bedienungsanleitung
Brechen Sie die Installation ab, falls beim Einlegen der CD ROM der Installationsbildschirm der Software erscheint.
Wenn [INDEX.pdf] auf der CD ROM geöffnet wird, erscheint eine Liste der Bedienungsanleitungen. Klicken Sie auf den Dokumentennamen der zu öffnenden Anleitung.
ppZum Lesen der PDF Dateien benötigen Sie Adobe® Reader®.
Dieses Programm kann von der Homepage von Adobe Systems heruntergeladen werden.
FRANÇAIS
ppComment ouvrir les fichiers PDF des manuels du mode d’emploi
Arrêter l’installation si l’écran d’installation du logiciel s’ouvre quand le CD ROM est inséré.
Quand [INDEX.pdf] sur le CD ROM s’ouvre, la liste des manuels du mode d’emploi s’affiche.
Cliquer sur le nom du document correspondant au manuel à consulter.
ppAdobe® Reader® est nécessaire pour lire les fichiers PDF.
Ce logiciel peut être téléchargé depuis la page d’accueil d’Adobe Systems.
ITALIANO
ppCome aprire i file dei manuali di istruzioni per l’uso
Se inserendo il CD ROM si apre la schermata di installazione del software, interrompere l’installazione. Aprendo [INDEX.pdf] sul CD ROM, viene visualizzato un elenco di manuali di istruzioni per l’uso.
Fare clic sul nome del documento corrispondente al manuale da aprire.
ppPer leggere i file PDF è necessario Adobe® Reader®. Il programma può essere scaricato dal sito Web di Adobe Systems.
ESPAÑOL
ppModo de abrir los archivos PDF que contienen el manual de las instrucciones de funcionamiento
Interrumpa la instalación si la pantalla de instalación del software se abre como resultado de insertar el CD ROM. Cuando se abra [INDEX.pdf] en el CD ROM se visualizará una lista de los manuales de instrucciones de funcionamiento.
Haga clic en el nombre de documento del manual que va a abrir.
ppPara leer los archivos PDF se necesita el programa Adobe® Reader®.
Este programa se puede descargar de la página inicial de Adobe Systems.
РУССКИЙ
ppКак открыть PDFфайлы инструкции по эксплуатации
Прекратите установку, если в результате загрузки диска CD ROM появилось окно установки программного обеспечения.
При открытии файла [INDEX.pdf] на диске CD ROM будет отображен список инструкций по эксплуатации. Щелкните название документа руководства, чтобы открыть его.
pp Для чтения PDFфайлов потребуется Adobe®
Reader®.
ppДанное программное обеспечение можно скачать с домашней страницы Adobe Systems.
2
Read this first!
|
|
|
|
|
|
|
|
|
|
|
|
|
WARNING: |
|
CAUTION: |
|
|
|
• To reduce the risk of fire, do not expose this |
|
Do not remove panel covers by unscrewing. |
|
|
|
|
equipment to rain or moisture. |
|
To reduce the risk of electric shock, do not remove the |
|
|
• To reduce the risk of fire, keep this equipment away |
|
covers. No user serviceable parts inside. |
|
|
|
|
from all liquids. |
|
Refer servicing to qualified service personnel. |
|
|
|
Use and store only in locations which are not |
|
|
|
|
|
|
|
||
|
|
exposed to the risk of dripping or splashing liquids, |
|
CAUTION: |
|
|
|
and do not place any liquid containers on top of the |
|
|
|
|
|
equipment. |
|
To reduce the risk of fire or electric shock and |
|
|
|
|
|
annoying interference, use the recommended |
|
|
|
|
|||
|
|
|
|
accessories only. |
|
|
WARNING: |
||||
|
|
|
|
||
|
|
|
|
||
|
Always keep memory cards or accessories out of the |
|
CAUTION: |
|
|
|
reach of babies and small children. |
|
|
||
|
|
|
|
In order to maintain adequate ventilation, do not install |
|
|
|
|
|||
|
|
|
|
or place this unit in a bookcase, built in cabinet or any |
|
|
WARNING: |
||||
|
|
other confined space. To prevent risk of electric shock |
|
||
|
Installation should only be performed by qualified |
|
or fire hazard due to overheating, ensure that curtains |
|
|
|
installation personnel. Improper installation may result |
|
and any other materials do not obstruct the ventilation. |
|
|
|
in the entire apparatus falling down and causing injury. |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
indicates safety information. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FCC NOTICE (USA)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also, any unauthorized changes or modifications to this equipment could void the user’s authority to operate it.
NOTIFICATION (Canada)
This class A digital apparatus complies with Canadian ICES 003.
indicates safety information.
3
Read this first! (continued)
IMPORTANT SAFETY INSTRUCTIONS
1)Read these instructions.
2)Keep these instructions.
3)Heed all warnings.
4)Follow all instructions.
5)Do not use this apparatus near water.
6)Clean only with dry cloth.
7)Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9)Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10)Protect the power cord form being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11)Only use attachments/accessories specified by the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip over.
13)Unplug this apparatus during lightning storms or when unused for long periods of time.
14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
EEEYönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
4
Read this first! (continued)
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1.Applicable standards and operating environment (AW RP120G) The apparatus is compliant with:
•standards EN55103 1 and EN55103 2, and
•electromagnetic environments E1, E2, E3 and E4.
2.Pre requisite conditions to achieving compliance with the above standards
<1>Peripheral equipment to be connected to the apparatus and special connecting cables
•The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to the apparatus.
•The purchaser/user is urged to use only the connecting cables described below.
<2>For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.
•Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75 ohm type high frequency applications, for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75 ohm type high frequency applications, are recommended for analog video signals.
•Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high frequency transmission applications, for analog audio signals.
•Other connecting cables (LAN, RS 422)
Use shielded cables, which provide quality performance for high frequency applications, as connecting cables.
•When connecting to the DVI signal terminal, use a cable with a ferrite core.
•If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.
3.Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by these standards. However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strong electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse effects of the interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference. 2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.
Declaration of Conformity
with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in Electrical and Electronic Equipment
(adopted by Order №1057 of Cabinet of Ministers of Ukraine)
The Product is in conformity with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in electrical and electronic equipment (TR on RoHS).
The content of hazardous substance with the exemption of the applications listed in the Annex №2 of TR on RoHS:
1.Lead (Pb) – not over 0,1 % or 1000wt ppm;
2.Cadmium (Cd) – not over 0,01 % or 100wt ppm;
3.Mercury (Hg) – not over 0,1 % or 1000wt ppm;
4.Hexavalent chromium (Cr6+) – not over 0,1 % or 1000wt ppm;
5.Polybrominated biphenyls (PBBs) – not over 0,1 % or 1000wt ppm;
6.Polybrominated diphenyl ethers (PBDEs) – not over 0,1 % or 1000wt ppm.
Manufactured by: Panasonic Corporation, Osaka, Japan
Importer’s name and address of pursuant to EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
5
Contents
Read this first!. . . . . . . . . . . . . . . . . . . . . . .3 Introduction. . . . . . . . . . . . . . . . . . . . . . . .7 Features. . . . . . . . . . . . . . . . . . . . . . . . . 8 Supported remote cameras. . . . . . . . . . . . . . . . . 8 Supported switcher. . . . . . . . . . . . . . . . . . . . .8 Accessories. . . . . . . . . . . . . . . . . . . . . . . .9 Precautions for use. . . . . . . . . . . . . . . . . . . . .9 Precautions for installation. . . . . . . . . . . . . . . . .10 Appearance. . . . . . . . . . . . . . . . . . . . . . . 11
Parts and their functions. . . . . . . . . . . . . . . . . .12
Control panel. . . . . . . . . . . . . . . . . . . . . . 12 Rear panel. . . . . . . . . . . . . . . . . . . . . . . 18
Basic operations of the unit. . . . . . . . . . . . . . . . .19 Basic operations for the menus. . . . . . . . . . . . . . . 20
Connections. . . . . . . . . . . . . . . . . . . . . . . 21
Examples of IP connections. . . . . . . . . . . . . . . . 21 Examples of serial connections. . . . . . . . . . . . . . . 23
About trademarks and registered trademarks
zzMicrosoft®, Windows®, Windows® 7, and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the United States, Japan, and/or other countries.
zzIntel® and Intel® CoreTM are trademarks or registered trademarks of Intel Corporation and its subsidiaries in the United States and/or other countries.
zzAdobe® and Reader® are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
zzSDHC logo is a trademark of SD 3C, LLC.
zzOther company names and product names appearing in this manual are the registered trademarks or trademarks of their respective companies.
Copyrights
It is prohibited to transfer, copy, disassemble, decompile, and reverse engineer the software included with the unit, as well as export it in violation of the export laws.
Illustrations and screen images in this manual
Illustrations of the unit and screens may appear different from the actual unit and screens.
Network settings of the unit. . . . . . . . . . . . . . . . .27
Settings for connecting with the remote cameras and switcher. . 29
Setting the connection types (serial/IP/no connection)
for remote cameras. . . . . . . . . . . . . . . . . . .30 Setting the connection type (IP/no connection) for the switcher. . .30 Setting the IP addresses automatically (auto IP setting). . . . . .30 Swapping connection destination IP addresses. . . . . . . . .35 Manually setting the connection destination IP addresses
(remote cameras). . . . . . . . . . . . . . . . . . . 35 Setting the connection destination port number. . . . . . . . .36 Manually setting the connection destination IP address (switcher). . 36 Initializing the connection destination IP addresses set
on the unit. . . . . . . . . . . . . . . . . . . . . . 36
Selecting a camera group. . . . . . . . . . . . . . . . . .37 Selecting a remote camera. . . . . . . . . . . . . . . . . 38 Troubleshooting . . . . . . . . . . . . . . . . . . . . . 39 Specifications. . . . . . . . . . . . . . . . . . . . . . 40 Index. . . . . . . . . . . . . . . . . . . . . . . . . . 41
Abbreviations
The following abbreviations are used in this manual. zzMicrosoft® Windows® 7 Professional SP1 32/64 bit is referred to as
“Windows 7”. zzMicrosoft® Windows® XP Professional SP3 and
Microsoft® Windows® XP Home Edition SP3 are referred to as “Windows XP”.
zzSD memory cards and SDHC memory cards are both referred to as “memory cards”.
They are referred to individually in descriptions in which each of them is discussed separately.
zzIn these instructions, the phrases “HD integrated camera” and “pan tilt head and camera combination” are referred to collectively as “remote camera” except in places where specific equipment is mentioned.
Furthermore, the product numbers of equipment are referred to as follows.
Equipment part |
Notation in |
|
number |
this manual |
|
AW RP120G |
AW RP120 |
|
AW HE60HN |
|
|
|
|
|
AW HE60SN |
AW HE60 |
|
AW HE60HE |
||
|
||
|
|
|
AW HE60SE |
|
|
|
|
|
AW HE50HN |
|
|
AW HE50SN |
AW HE50 |
|
|
||
AW HE50HE |
||
|
||
AW HE50SE |
|
|
|
|
|
AW HE120WP |
|
|
AW HE120KP |
AW HE120 |
|
|
||
AW HE120WE |
||
|
||
|
|
|
AW HE120KE |
|
|
AW HE100N |
AW HE100 |
|
|
||
AW HE100E |
||
|
||
AW HE2P |
AW HE2 |
|
|
||
AW HE2E |
||
|
||
AW PH360N |
AW PH360 |
|
|
||
AW PH360L |
||
|
||
|
|
|
AW PH405N |
AW PH405 |
|
AW PH405E |
||
|
||
|
|
Equipment part |
Notation in |
|
number |
this manual |
|
AW PH650N |
AW PH650 |
|
AW PH650L |
||
|
||
|
|
|
AW PH400P |
AW PH400 |
|
AW PH400E |
||
|
||
|
|
|
AW IF400G |
AW IF400 |
|
AW HE870N |
AW HE870 |
|
AW HE870E |
||
|
||
|
|
|
AW E860N |
AW E860 |
|
AW E860L |
||
|
||
|
|
|
AW E750P |
AW E750 |
|
AW E750E |
||
|
||
|
|
|
AW E650P |
AW E650 |
|
|
||
AW E650E |
||
|
||
AW E350P |
AW E350 |
|
|
||
AW E350E |
||
|
||
AK HC1500G |
AK HC1500 |
|
AK HC1800G |
AK HC1800 |
|
AW HS50N |
AW HS50 |
|
|
||
AW HS50E |
||
|
||
|
|
|
AW RP50N |
AW RP50 |
|
AW RP50E |
||
|
||
|
|
6
Introduction
Overview
This unit is a controller which is designed to control remote cameras.
It can be used to control up to 100 remote cameras when IP connections are used, and up to 5 remote cameras when serial connections are used.
Also, operation linked to an AW HS50 compact live switcher can be implemented by means of an IP connection.
Required personal computer environment
Run the software that is supplied with the unit on a personal computer which satisfies the following specifications.
CPU |
Intel® CoreTM2 Duo 2.4 GHz or faster, or a CPU with |
|
equivalent specs |
|
|
Memory |
Windows XP: 512 MB or more |
|
Windows 7: 1 GB or more |
|
|
Network function |
10BASE T or 100BASE TX |
|
|
Image display |
Resolution: 1024 768 pixels or more |
function |
Color generation: True Color (24 bits or more) |
|
|
Supported |
Windows XP |
operating systems |
Windows 7 |
|
|
Hard disk drive |
At least 50 MB of free space |
|
|
Other |
CD ROM drive |
|
(For using the Operating Instructions and various |
|
software) |
|
Adobe® Reader® |
|
(For browsing the Operating Instructions on the |
|
CD ROM) |
|
|
Disclaimer of warranty
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1)ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;
(2)PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;
(3)UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER;
(4)INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5)ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6)ANY INCONVENIENCE, DAMAGES OR LOSSES RESULTING FROM ACCIDENTS CAUSED BY AN INADEQUATE INSTALLATION METHOD OR ANY FACTORS OTHER THAN A DEFECT IN THE PRODUCT ITSELF;
(7)LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE;
(8)ANY DAMAGE OR CLAIMS DUE TO LOSS OR LEAKAGE OF IMAGE DATA OR SETTING DATA SAVED ON THIS UNIT OR ON A MEMORY CARD OR COMPUTER.
Network security
As you will use this unit connected to a network, your attention is called to the following security risks.
(1)Leakage or disclosure of information transmitted via this unit
(2)Unauthorized use of this unit by a third person with malicious intent
(3)Interference or stoppage of this unit by a third person with malicious intent
It is your responsibility to take sufficient network security measures such as those described below to protect yourself against the above risks.
zzUse this unit in a network secured by a firewall, etc.
zzIf this unit is used in a system with a computer connected, make sure that checks for and removal of computer viruses and malicious programs are implemented regularly.
zzDo not install the unit in a location where the unit, cables, and other parts may be easily damaged.
User authentication
The user authentication function of this unit uses basic authentication. When basic authentication is used on an unsecured network, there is the risk of passwords being leaked.
We recommend using host authentication in such a case.
Configure the host authentication settings on the remote cameras. For details, refer to the Operating Instructions for the remote cameras.
Restrictions on use
With regards to the network for connecting the remote cameras and personal computer to the unit, we recommend that the segment is the same.
If there are connections for which the segment is different, events dependent upon, for example, settings unique to the network equipment may occur so carefully check the connections prior to the start of operation.
7
Features
IP connections and serial connections supported
IP connections
zzUp to 100 remote cameras *1 can be controlled via a network hub (switching hub).
zzThe unit’s auto IP setting function can be used to automatically assign and control the IP addresses of the remote cameras *1 and switcher *2.
*1: Supported cameras: AW HE50, AW HE60, AW HE120, and AW HE2 *2: Supported switcher: AW HS50
zzOne remote camera can be simultaneously controlled from up to 5 units.
zzThe setup software supplied with this unit can be used to set the IP addresses of the remote cameras and switchers from a personal computer via the unit.
Serial connections
zzUp to 5 remote cameras can be connected.
Easy to operate the remote cameras
zzThe unit is equipped with dedicated levers, buttons, and dials for performing pan, tilt, zoom, and focus operations. Furthermore, there is a dedicated speed adjustment knob for each of them. Camera angle adjustment can be performed quickly and reliably.
zzThe unit is equipped with an AWB button and ABB button for executing automatic adjustment of the white balance and black balance. Furthermore, there are dedicated dials for adjusting the pedestal and gain for each of the R channel and B channel. Manual color adjustment is also easy.
zzThe 1 to 50 number buttons and page buttons enable quick access operations at sites where presets are used frequently.
Also, the speed at which a remote camera moves to a preset position (PRESET SPEED) can be memorized for each preset number of the unit. Thus, a remote camera can be operated at a different speed depending on the preset number in accordance with operation, enabling video playback at a variety of speeds.
zzTracing memory is incorporated for recording a series of operations.
It allows you to duplicate remote camera operations.
Supported remote cameras
zzHD integrated cameras
AW HE50, AW HE60, AW HE120, AW HE100, and AW HE2 *3
*3: Some operations of the AW HE2 differ from those of other HD integrated cameras. For details, refer to “Operations of AW HE2” in <Operations and Settings> (page 51).
zzPan tilt head and camera combinations
Systems including a combination of any of the following pan tilt heads and cameras can be controlled.
<Pan tilt heads>
AW PH360, AW PH405, AW PH650, and AW PH400 *4
*4: AW IF400 is required to connect AW PH400 to the unit.
<Cameras>
AW HE870, AW E860, AW E750, AW E650, AW E350, AK HC1500, and AK HC1800
Supported switcher
zzCompact live switcher
AW HS50
8
Accessories
Check the accessories.
zzAfter unpacking the product, dispose of the packaging material appropriately.
CD ROM..........................1
zzOperating Instructions <Basics>
zzOperating Instructions <Operations and Settings>
zzSetup Software
Precautions for use
Observe the following in addition to the information included in “Read this first!”.
Handle carefully
Do not drop the product, or subject it to a strong impact or vibration. Do not carry or move the product by the PAN/TILT lever or a dial. Doing so may cause a failure or accident.
Use the product in an ambient temperature of 0 °C to 40 °C (32 °F to 104 °F)
Avoid using the product in a cold place where the temperature drops below 0 °C (32 °F) or in a hot place where the temperature rises above 40 °C (104 °F) because an extremely low or high temperature will adversely affect the internal parts.
Turn off the power before connecting or disconnecting cables
Before connecting or disconnecting the cables, be sure to turn the power off.
Avoid humidity and dust
Avoid using the product in a very humid or dusty place because a lot of humidity and dust will cause damage to the internal parts.
Cleaning
Turn the power off and wipe the product with a dry cloth. To remove stubborn dirt, dip a cloth into a diluted solution of kitchen detergent (neutral detergent), wring it out well, and wipe the product gently.
Then, wipe the product with a cloth dampened with water. Finally, wipe the product with a dry cloth.
Notes
zzAvoid using benzine, paint thinners and other volatile fluids. zzIf a chemical cleaning cloth is to be used, carefully read through
the precautions for its use.
Disposal of the unit
When the unit has reached the end of its service life and is to be disposed of, ask a qualified contractor to dispose of the unit properly in order to protect the environment.
9
Precautions for installation
In addition to the safety precautions given in “Read this first!”, also observe the following instructions.
Be sure to ask your dealer to perform the installation and connection work for the unit.
Connecting a power supply
zzInsert the DC plug for the external DC power supply all the way in until it locks into place.
LCD CONTRAST |
REMOTE |
DC plug |
|
|
SIGNAL |
GND |
|
|
|
|
|
Do not allow any foreign objects to enter inside the unit zzAllowing water, metal items, food or drink, or other foreign objects to
enter inside the unit may cause a fire or electric shock.
Installation location
zzThis unit is designed for indoor use only. zzInstall and use the unit in a stable location.
zzAvoid installing the unit where it will be exposed to direct sunlight. zzInstalling the unit in a location with a lot of humidity, dust, or vibration
may result in a failure.
zzWhen the unit will not be used for a long time, turn off the power switch and remove the DC plug for the external DC power supply to save power.
Example of embedding the unit in a desktop
When you will use the unit embedded in a desktop, refer to the following procedure.
1. Make mount angles suitable for the installation location.
<Mount angle example>
zzDesk mounting side |
Unit: mm (inch) |
||
|
25 (31/32) |
|
|
160 (6-5/16) |
Ø5 (3/16) |
|
|
(Desk mounting holes) |
|
||
|
|
||
zzUnit mounting side |
|
|
|
210 (8-9/32) |
|
|
|
140 (5-1/2) |
|
|
|
|
2 |
|
30 |
|
(3/32) |
|
|
|
|
|
(1-3/16) |
|
21 |
35 |
|
Ø3.5 (1/8) |
(13/16) |
|
|
(1-3/8) |
|
||
(Unit mounting hole) |
|
|
|
|
|
|
|
2.Attach the mount angles to the sides of the unit with four M3 screws.
Unit
M3 screws
Mount angle
Note
zzFor details on the dimensions for attaching mount angles to the unit, refer to “Appearance” (page 11).
3.Insert the unit into the desktop hole and then fix it in place with four screws.
zzProvide screws that match the size of the desktop mounting holes (e.g. Ø5 mm [3/16 inches]).
4.If necessary, make and attach a panel to cover the rest of desktop hole.
Panel to cover hole
10
Appearance
Unit: mm (inch)
317.2 (12-1/2) |
77 (3-1/32) |
265 (10-7/16)
342 (13-15/32)
54 (2-1/8) |
161 (6-11/32) |
zzMount angle attachment position
|
17 (21/32) |
2 M3 |
|
|
52.5 (2-1/16) |
39 |
(1-17/32) |
74.3 (2-15/16) |
51 (2) |
140 (5-1/2) |
12.4 (1/2) |
249.6 (9-13/16) |
11
Parts and their functions
Control panel
|
|
|
|
|
|
|
|
|
|
|
|
Menu operation section |
Memory card section |
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Indicator section |
|
|
User button section |
Color adjustment |
Camera selection |
section |
|
|
section |
|
Pan and tilt section |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Focus, zoom and iris section |
Menu and memory selection section |
|||
1POWER indicator [POWER]
This turns on when the POWER switch ( ) on the rear panel is set to ON while power is supplied to the DC IN socket ( ).
2ALARM indicator [ALARM]
This turns on when there is a problem with the power supply (voltage drop).
It also turns on when an alarm (a cooling fan alarm or pan/tilt error) has been received from a remote camera.
“Checking alarm information” in <Operations and Settings> (page 40)
3LCD panel
This indicates the current setting statuses.
Menu operation section
4CAMERA OSD button [CAMERA OSD]
Hold down this to turn the button indicator on or off and switch the operation target of the F1 dial and F2 dial.
Button indicator on: The OSD menu of the selected remote camera is displayed.
The OSD menu of the remote camera can be operated with the F1 dial and F2 dial.
Button indicator off: The OSD menu of the selected remote camera is not displayed.
The menus of the unit can be operated with the F1 dial and F2 dial.
12
Parts and their functions (continued)
5F1 dial [F1]
F2 dial [F2]
Use these to operate the menus of the unit or the OSD menu of a remote camera.
Use the CAMERA OSD button (4) to select which operation to perform.
When the dials are used to operate the menus of the unit, the F1 dial operates the items displayed at the top of the LCD panel of the unit, and the F2 dial operates the items displayed at the bottom of the LCD panel.
Operation of the OSD menu of a remote camera differs depending on the camera type.
“Operating the OSD menu of a remote camera” in <Operations and Settings> (page 11)
6EXIT button [EXIT]
Use this to cancel the changes to the settings during operation of the OSD menu of a remote camera.
It cannot be used during operation of the menus of the unit.
“Operating the OSD menu of a remote camera” in <Operations and Settings> (page 11)
Camera selection section
7Mode selection button [SELECT]
Each press of this switches the button indicator between on and off in the order of on → off → on, and so on, and switches the operation mode of the camera selection buttons (8).
Button indicator on: Camera selection mode Button indicator off: Camera group selection mode
8Camera selection buttons
[CAMERA SELECT/GROUP SELECT 1 to 10]
Use these to select the remote camera or camera group to control from the unit.
Pressing any of [1] to [10] in camera selection mode switches to the corresponding remote camera.
Holding down any of [1] to [10] in camera group selection mode switches to the corresponding camera group and turns on the corresponding camera group indicator (9).
Note
zzIf a camera selection button is pressed to switch the remote camera that the unit controls while the OSD menu of a remote camera is displayed, the CAMERA OSD button (4) indicator turns off and the OSD menu of the remote camera originally selected disappears.
9Camera group indicators [CAMERA GROUP 1 to 10]
The indicator for the selected camera group number is on.
:Camera status indicators [1] to [10]
These indicate the statuses of the remote cameras assigned to [1] to
[10].
“Selecting a remote camera” (page 38)
Pan and tilt section
PAN/TILT lever
Use this to control the direction in which the currently selected remote camera points.
The movement speed differs depending on the angle to which the PAN/TILT lever is moved.
Moved left or right: The camera points to the left or right.
Moved toward you or away from you:
The camera points up or down.
zzWhen the function for linking with a switcher is enabled, you can use the PAN/TILT lever to control switcher parameters.
“Operating the switcher with the PAN/TILT lever and ZOOM button” in <Operations and Settings> (page 34)
zzSetting “REVERSE” in PAN DIRECTION menu [26] and TILT DIRECTION menu [27] changes the direction the camera moves in relation to the direction that the lever is moved.
“Setting the pan, tilt, zoom, and focus operation directions” in <Operations and Settings> (page 23)
<PAN/TILT SPEED dial [SPEED]
Use this to adjust the operation speed variation amount for PAN/TILT lever operation.
Turned clockwise |
: |
Operation is at a higher speed (HI) |
Turned counterclockwise |
: |
Operation is at a lower speed (LOW) |
=PAN/TILT ENABLE button [ENABLE]
Use this to enable PAN/TILT lever operation.
Button indicator on or blinking: PAN/TILT lever operation is
enabled.
Button indicator off : PAN/TILT lever operation is disabled.
zzThe PAN/TILT ENABLE button indicator is on while the PAN/TILT lever is being used to control the direction in which the remote camera points.
zzThe PAN/TILT ENABLE button indicator is blinking while the PAN/ TILT lever is being used to control the switcher parameters.
zzWhen the “7. P/T/Z CONTROL” item in SW FUNCTION menu [42] is set to “Button Select”, pressing the PAN/TILT ENABLE button switches the control application of the PAN/TILT lever.
“Operating the switcher with the PAN/TILT lever and ZOOM button” in <Operations and Settings> (page 34)
13
Parts and their functions (continued)
Focus, zoom and iris section
|
|
|
|
|
|
|
|
|
|
>FOCUS dial [FOCUS]
Use this to manually control the focus.
During auto focusing (when the auto focus button [ ] indicator is on), operation is disabled.
Turned clockwise : The focus moves to the far end. Turned counterclockwise: The focus moves to the near end.
zzSetting “REVERSE” in FOCUS DIRECTION menu [29] changes the direction the focus moves in relation to the direction that the FOCUS dial is turned.
?Auto focus button [AUTO]
Use this to set focus control to “Auto (auto focus)”.
During auto focusing, operation of the FOCUS dial ( ) and one touch auto focus button ( ) is disabled.
Button indicator on: Auto focus Button indicator off: Manual focus
zzWhen a lens equipped with an extender function is used for the remote camera, each press of this button switches the extender function on or off.
Button indicator on: The extender function is enabled. Button indicator off: The extender function is disabled.
(For details on how to connect the lens control cables to the pan tilt head, refer to the Operating Instructions of the pan tilt head.)
zzButton operation is disabled if the remote camera has no auto focus function and lens extender function.
One touch auto focus button [OTAF]
When this button is pressed during manual focusing (when the auto focus button [ ] indicator is off), the button indicator turns on for a brief moment and the auto focusing operation is performed to bring the subject into focus.
zzButton operation is disabled if the remote camera has no auto focus function.
AFOCUS SPEED dial [SPEED]
Use this to adjust the operation variation amount for FOCUS dial ( ) operation.
Turned clockwise |
: |
Operation is at a higher speed (HI) |
Turned counterclockwise: |
Operation is at a lower speed (LOW) |
|
BZOOM button [ZOOM]
Use this to adjust the lens zoom.
The zooming speed changes depending on the extent to which the button is pressed.
When the TELE side is pressed : Moves toward the telephoto end.
When the WIDE side is pressed: Moves toward the wide angle end.
zzWhen the function for linking with a switcher is enabled, you can press the ZOOM button to control switcher parameters.
“Operating the switcher with the PAN/TILT lever and ZOOM button” in <Operations and Settings> (page 34)
zzSetting “REVERSE” in ZOOM DIRECTION menu [28] changes the direction the lens zoom moves in relation to the direction that the ZOOM button is moved.
ZOOM SPEED dial [SPEED]
Use this to adjust the operation variation amount for ZOOM button ( ) operation.
Turned clockwise |
: |
Operation is at a higher speed (HI) |
Turned counterclockwise: |
Operation is at a lower speed (LOW) |
|
IRIS dial [IRIS]
During manual iris (when the auto iris button [ ] indicator is off), use this to manually control the lens iris.
During auto iris (when the auto iris button [ ] indicator is on), use this to adjust the convergence level of the auto iris of the remote camera.
Turned clockwise |
: |
The lens iris opens. |
Turned counterclockwise: |
The lens iris closes. |
|
EAuto iris button [AUTO]
Use this to set lens iris control to “Auto (auto iris)”.
Button indicator on |
: |
Auto iris |
Button indicator off |
: |
Manual iris |
zzWhen AW HE50 or AW HE60 is being controlled, Contrast Mode switches to “Auto” or “Manual” in conjunction with the selection of auto iris or manual iris. Also, if you set the shooting mode to “FullAuto”, the lens iris is fixed to auto iris and button operation is disabled.
zzWhen the AW PH400 is connected via a protocol converter (AW IF400), the remote camera operates in the “auto iris” state regardless of the auto iris button state if the power of the
AW PH400 is turned on after the power of the unit. Press the auto iris button to match the states of the unit and camera and then perform the operation.
FOCUS/ZOOM/IRIS ENABLE button [ENABLE]
Use this to enable or disable operation of the FOCUS dial ( ), ZOOM button ( ) and IRIS dial ( ).
Button indicator on or blinking:
Operation of the FOCUS dial, ZOOM button and IRIS dial is enabled.
Button indicator off: Operation of the FOCUS dial, ZOOM button and IRIS dial is disabled.
zzThe FOCUS/ZOOM/IRIS ENABLE button indicator is on while the ZOOM button is being used to control the lens zoom.
zzThe FOCUS/ZOOM/IRIS ENABLE button indicator is blinking while the ZOOM button is being used to control the switcher parameters.
zzWhen the “7. P/T/Z CONTROL” item in SW FUNCTION menu [42] is set to “Button Select”, pressing the FOCUS/ZOOM/IRIS ENABLE button switches the control application of the ZOOM button.
“Operating the switcher with the PAN/TILT lever and ZOOM button” in <Operations and Settings> (page 34)
14
Loading...