NEC PX-60XM5A, 50XM6, 42XM5, PX-50XM6A, PX-42XM5A User Manual

...

PlasmaSync Plasma Monitor

PlasmaSync

PX-42XM5A

PlasmaSync

PX-50XM6A

PlasmaSync

PX-60XM5A

User’s Manual

™

42XM5

™

50XM6

™

60XM5

NEC Corporation of America

User’s Manual

Manuel d’utilisation

Manual del Usuario

Manual de Usuário

User’s Manual

(Enhanced split screen Model)

ENGLISH

Important Information

Precautions

Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SE RVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warnings and Safety Precaution

This plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Please see the section “Plasma monitor cleaning procedure”. The plasma display panel consists of fine picture elements (cells) with more than 99.99 percent active cells. There may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal heat buildup. Do not cover rear vents or install the unit in a closed cabinet or shelves. If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for 60 minutes to cool the monitor. If the problem persists, contact your dealer for service.

2. Do not use this unit’s polarized plug with extension cords or outlets unless the prongs can be completely inserted.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to modify the power cord.

5. Unplug the power cord during electrical storms or if the unit will not be used over a long period.

6. Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. The manufacturer is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized Service Centers.

8. This equipment shall be connected to a MAIN outlet with a protective earth-ground connection.

9. The outlet shall be installed near the equipment and shall be easily accessible.

To avoid damage and prolong operating life:

1. Use only with 100 V to 240 V 50 Hz/60 Hz AC power supply. Continued operation at line voltages greater than 100 V to 240 V AC will shorten the life of the unit, and might even cause a fire hazard.

2. Handle the unit carefully when installing it and do not drop.

3. Set the unit away from heat, excessive dust, and direct sunlight.

4. Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord and have it serviced by an authorized Service Center.

5. Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

6. For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

7. As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel.

8. To avoid sulfurization it is strongly recommended not to place the unit in a dressing room in a public bath or hot spring bath.

9. Do not use in a moving vehicle, as the unit could drop or topple over and cause injuries.

10. Do not place the unit on its side, upside-down or with the screen facing up or down, to avoid combustion or electric shock.

11. To prevent a fire hazard, do not place near an open flame (such as a lighted candle).

Plasma monitor cleaning procedure:

1. Use a soft dry cloth to clean the front panel and bezel area. Never use solvents such as alcohol or thinner to clean these surfaces.

2. Clean plasma ventilation areas with a vacuum cleaner with a soft brush nozzle attachment.

3. To ensure proper ventilation, cleaning of the ventilation areas must be carried out monthly. More frequent cleaning may be necessary depending on the environment in which the plasma monitor is installed.

Recommendations to avoid or minimize image retention:

Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible to image retention under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged period of time, can result in image retention if proper precautions are not taken. To protect your investment in this plasma monitor, please adhere to the following guidelines and recommendations for minimizing the occurrence of image retention:

* Always enable and use your computer’s screen saver function

during use with a computer input source. * Display a moving image whenever possible. * Change the position of the menu display from time to time. * Always power down the monitor when you are finished using it.

If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of image retention:

* Lower the Brightness and Contrast levels as much as possible without

impairing image readability. * Display an image with many colors and color gradations (i.e.

photographic or photo-realistic images). * Create image content with minimal contrast between light and dark

areas, for example white characters on black backgrounds. Use

complementary or pastel color whenever possible. * Avoid displaying images with few colors and distinct, sharply defined

borders between colors.

Plasma monitor driving sound

The panel of the Plasma monitor is composed of extremely fine pixels and these pixels emit light according to received video signals. This principle may cause you to hear a buzz or electrical hum coming from the Plasma monitor. Also note that the rotation speed of the cooling fan motor increases when the ambient temperature of the Plasma monitor becomes high. You may hear the sound of the motor at that time.

Note:

The following items are not coverd by the warranty.

• Image retention

• Panel generated sound, examples: Fan motor noise, and electrical circuit humming /glass panel buzzing.

Contact your dealer for other recommended procedures that will best suit your particular application needs.

En-2

Warning

dnd

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment ANSI/NFPA 75.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

NOTE: When you use an RGB cable (not supplied), use an RGB cable including the ferrite core (not supplied) on both ends of the cable. If you do not this, this monitor will not conform to mandatory FCC standards.

NOTE: When you use the power cable (supplied), use the supplied ferrite cores. Set the ferrite cores (supplied) on both ends of the power cable (supplied), and then use the bands (supplied) to fasten the ferrite cores (supplied) to the power cable (supplied). If you do not this, this monitor will not conform to mandatory FCC standards.

wer

supplie

WARNING

This product equipped with a three-wire grounding (earthed) plug - a plug that has a third (grounding) pin. This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.

Operating Environment

Operating environment temperature and humidity: 0 °C to +40 °C (+32 °F to +104 °F); less than 80 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

Disposing of your used product

EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes plasma monitors and their electrical accessories. When you dispose of such products, please follow the guidance of your local authority and/or ask the shop where you purchased the product. After collecting the used products, they are reused and recycled in a proper way. This effort will help us reduce the wastes as well as the negative impact to the human health and the environment at the minimum level. The mark on the electrical and electronic products only applies to the current European Union Member States.

CAUTION

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country/ area.

CAUTION

When changing batteries, use only conventional non-rechageable alkaline or manganese batteries

NOTE: When you use a remote cable (not supplied), use the supplied ferrite core. Wind the remote cable (not supplied) around the ferrite core (supplied) once, and then fasten

(2). Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the institutions.

the catch. If you do not this, this monitor will not conform to mandatory FCC standards.

Remote cable (not supplied)

To plasma monitor

core

En-3

Contents

Important Information .................................. En-2

Contents ...................................................... En-4

Contents of the Package ........................................En-4

Options .............................................................. En-4

Installation .................................................. En-5

Ventilation Requirements for enclosure mounting ...... En-5

Creating a video wall ........................................... En-6

Cable Management.............................................. En-6

Caution when placing the plasma monitor in portrait mode .....

Using the remote control ....................................... En-7

Battery Installation and Replacement .......................... En-7

Using the wired remote control mode ......................... En-7

Operating Range ......................................................... En-7

En-7

Part Names and Function .............................. En-8

Front View .......................................................... En-8

Rear View/ Terminal Board ...................................En-9

Remote Control .................................................. En-12

Basic Operations ......................................... En-13

POWER ............................................................ En-13

To turn the unit ON and OFF: ................................... En-13

VOLUME .......................................................... En-13

To adjust the sound volume:...................................... En-13

MUTE ............................................................... En-13

To mute the audio: .................................................... En-13

DISPLAY ............................................................En-13

To check the settings: ................................................ En-13

DIGITAL ZOOM ................................................. En-13

AUTO ADJUST .................................................. En-13

To adjust the size or quality of the picture automatically: ...

OFF TIMER ........................................................En-13

To set the off timer: ................................................... En-13

To check the remaining time: .................................... En-13

To cancel the off timer: ............................................. En-13

En-13

WIDE Operations ......................................... En-14

Wide Screen Operation (manual) ........................ En-14

When viewing videos or digital video discs .............. En-14

Wide Screen Operation with Computer Signals ..... En-15

When “PICTURE SIZE” is set to “OFF” .................. En-15

SPLIT SCREEN Operations ............................. En-16

Showing a couple of pictures on the screen at the same time ..

Operations in the Side-by-side mode ......................... En-16

Operations in the Picture-in-picture mode ................. En-17

Selecting the input signals to be displayed ................ En-17

Zooming in on a specific input .................................. En-17

Adjusting the OSM controls ...................................... En-17

En-16

OSM (On Screen Menu) Controls ................... En-18

Menu Operations ...............................................En-18

Menu Tree ......................................................... En-19

Picture Settings Menu.......................................... En-21

Adjusting the picture ................................................. En-21

Setting the picture mode according to the brightness

of the room ............................................................. En-21

Reducing noise in the picture .................................... En-21

Setting the color temperature .................................... En-21

Adjusting the color to the desired level ..................... En-22

Changing the Gamma Curve ..................................... En-22

Making the Low Tone adjustments ........................... En-22

Adjusting the colors .................................................. En-22

Audio Settings Menu .......................................... En-23

Adjusting the treble, bass and left/right balance and

audio input select .................................................... En-23

Setting the allocation of the audio connectors ........... En-23

Image Adjust Settings Menu ................................ En-23

Adjusting the Position, Size, Fine Picture,

Picture Adj and Underscan ..................................... En-23

Option1 Settings Menu ....................................... En-24

Setting the on-screen menu ....................................... En-24

Setting the BNC input connector type ....................... En-24

Checking the signal being transmitted to RGB1 terminal ...

Setting a computer image to the correct RGB select screen ....

Setting high definition images to the suitable screen size ...

Setting the Input Skip ................................................ En-25

Resetting to the default values ................................... En-25

Option2 Settings Menu ....................................... En-26

Setting the power management for computer images ....

POWER/STANDBY indicator .................................. En-26

En-24 En-24 En-25

En-26

Setting the picture to suit the movie .......................... En-26

Reducing image retention ......................................... En-26

Setting the gray level for the sides of the screen ........ En-28

Setting the screen size for S1/S2 video input ............. En-29

Setting the picture size for RGB input signals ........... En-29

Setting the signal and black level for DVI signal ...... En-29

Setting the Protocol set ............................................. En-29

Setting CloseCaption ................................................ En-30

Setting the contrast of CloseCaption ......................... En-30

Option3 Settings Menu ....................................... En-30

Using the timer ......................................................... En-30

Setting the power on mode ........................................ En-32

Enabling/disabling the front panel controls ............... En-32

Enabling/disabling remote control wireless

transmission ........................................................... En-33

Loop Out setting ....................................................... En-33

REMOTE ID setting ................................................. En-33

ID number setting ..................................................... En-33

Video Wall setting ..................................................... En-34

Option4 Settings Menu ....................................... En-36

Removing the sub screen area when there is no input

signal detected for the sub picture .......................... En-36

Displaying the entire image during DIGITAL ZOOM

operations ............................................................... En-36

Displaying still images in the sub screen ................... En-36

Switching the input source quickly ........................... En-37

Displaying the information as a text .......................... En-37

Advanced OSM Settings Menu ............................ En-38

Setting the menu mode .............................................. En-38

Language Settings Menu ..................................... En-38

Setting the language for the menus ........................... En-38

Color System Settings Menu ................................ En-38

Setting the video signal format .................................. En-38

Source Information Menu ....................................En-38

Checking the frequencies, polarities of input signals, and

resolution ............................................................... En-38

External Control ......................................... En-39

Application ....................................................... En-39

Connections ...................................................... En-39

Type of connector: D-Sub 9-pin male ....................... En-39

Communication Parameters .................................En-39

External Control Codes (Reference) ...................... En-39

Pin Assignments ......................................... En-39

mini D-Sub 15-pin connector (Analog) ................. En-39

DVI-D 24-pin connector (Digital) ..........................En-39

1/8 Stereo Mini Jack (not supplied) for

REMOTE IN/OUT ...........................................En-40

Connection with STB .................................... En-40

Troubleshooting .......................................... En-41

Table of Signals Supported .......................... En-42

Specifications ............................................. En-46

Limited Warranty

Plasma Monitors ................. En-49

Contents of the Package

䡺 Plasma monitor (⳯1) 䡺 Power cord (⳯1, 3 m/9.8 feet) 䡺 Remote control (⳯1) 䡺 AAA Batteries (⳯2, Manganese battery for remote

control)

䡺 Manuals (Start up Guide and CD-ROM) 䡺 Ferrite cores for power cord (⳯2), bands for power

cord (⳯2) 䡺 Ferrite core for remote cable (⳯2) 䡺 Cable clampers (⳯3), beads bands (⳯3)

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop Stand

• Attachable speakers

En-4

Installation

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the

monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

* Do not touch or hold the screen face when carrying the unit.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, Stand, etc.)

• For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

CAUTION

• Install the device following the installation manual of the optional accessory.

• Install the device in a stable and level environment that is strong enough to support the weight.

• Use the specified clasps for installing.

• After installation, take appropriate measures to prevent the plasma from tipping over or falling.

• Make sure to move or install the device with more than one person(s).

* Use only a mounting kit or stand recommended by the manufacturer and listed as an accessory.

Drawing A

Ventilation Requirements for

Drawing B

Wall

enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram when installing.

50 mm (2")

Wall

50 mm (2")

En-5

50 mm (2")

Creating a video wall

With built-in matrix display capability, you can create a (2⳯2, 3⳯3, 4⳯4, 5⳯5, 5⳯1, 1⳯5) video wall.

• Connect signal cables and remote cables as shown below.

Video signal RGB/DVD/HD signal

Remote control

REMOTE

EXTERNAL CONTROL

)

IN OUT

RCA phono plug

(IN/OUT)

VIDEO Signal

AUDIO

VIDEO

( MONO

DVD

YCb/PbCr/Pr

)

Remote control

RGB signal/ DVD/HD signal

BNC connector

RGB

DVD

R/Cr/Pr G/Y B/Cb/Pb

RGB

AUDIO

RGB

VDHD

(IN/OUT)

(

)

Digital RGB

DVI

(

)

MONO

EXTERNAL CONTROL

REMOTE

IN OUT

RGB

DVD

R/Cr/Pr G/Y B/Cb /Pb

RGB

AUDIO

RGB

VDHD

(IN/OUT)

(

Digital RGB

DVI

(

)

MONO

AUDIO

DVD

AUDIO

VIDEO

(IN/OUT)

Y Cb/Pb Cr/Pr

( ( MONO

)

MONO

AUDIO

(

)

MONO

BNC connector

OUT

RGB signal/ DVD/HD signal

Remote control

VIDEO Signal

OUT

Remote control

OUT

Note:

1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT. When LOOP OUT is ON, do not connect an OUTPUT signal from another unit as it may damage the other unit due to an extraordinary load.

2. LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.

3. LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.

Information

• To loop signals out to another plasma display, set the LOOP OUT to ON.

• To create a video wall, set the VIDEO WALL menu items properly.

• To connect monitors, please use a 1 m to 2 m (3.3 feet to 6.6 feet) BNC cable (any commercially available cable).

• If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024⳯768, 60 Hz signal.

• A distribution amplifier is particularly recommended when creating a 3⳯3 (or greater) video wall.

• When looping from plasma to plasma, a 1 m to 2 m (3.3 feet to 6.6 feet) 15 pin male D-Sub - 5BNC conversion cable is required.

OUT

Cable Management

Using the cable clampers and beads bands provided with the plasma display; Bundle the signal and audio cables at the back of the unit to connect to the display.

42XM5 50XM6 60XM5

Back of the unit

mounting holes

To attach

Insert q into a mounting hole, then snap w into the back of q to fix the clamper. Clampers are designed to be difficult to undo once in place. Please attach carefully. Cables can be routed to the right or left.

Back of the unit

mounting holes

Bunch separated cables together and secure them with the provided beads bands. Do not allow excessive stress to be placed on the ends of cables.

To detach

Using pliers, twist the clamper 90° and pull it outward. In some cases the clamper may have deteriorated over time and may get damaged when removed.

Back of the unit

mounting holes

En-6

Caution when placing the plasma monitor in portrait mode

OUT

REMOTE

EXTERNAL CONTROL

• Use the optional mount. Contact your store to purchase before installing.

• Rotate 90° clockwise as seen from the front when installing.

90°

• After installing, make sure the NEC logo is located at the left hand side of the screen when facing the plasma from the front.

• Be sure to set “OSM ANGLE” to “V” when using.

* Failure to heed the above cautions may lead to malfunction.

Using the remote control

INPUT SELECT

VOLUME

MENU/ENTER

Battery Installation and Replacement

Designated batteries: Please use size AAA (R03) or AAA (LR03). Insert the 2 “AAA” batteries, making sure to set them in with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the and indication inside the case.

DOWN UP LEFT/-RIGHT/+/EXIT

Operating Range

* Use the remote control within a distance of about 7 m/ 23

ft. from the front of the monitor’s remote control sensor and at horizontal and vertical angles of up to approximately 30°.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between the sensor and the remote control.

OPTION1

MENU/ENTER

OSM

DOWN UP LEFT/

VOLUME

BNC INPUT

: RGB

RIGHT/

D-SUB INPUT

INPUT SELECT

/EXIT

: RGB

RGB SELECT

: AUTO

HD SELECT

: 1080B

INPUT SKIP

: OFF

ALL RESET

: OFF 1024ⴒ768

SEL.

MENU/ENTER

Bottom side

Top side

EXIT

RETURN

3.Replace the cover.

Using the wired remote control mode

Connect the remote cable* to the remote control’s remote jack and the “REMOTE IN” terminal on the monitor. When the cable is connected, the mode automatically switches to wired remote control. When the wired remote control mode is used, the remote control can be operated even if no batteries are loaded.

Remote Control Cable*

To Remote Jack

Approx.

7 m/23 ft

CAUTION

• Use only the specified batteries.

• Make sure to insert the batteries correctly according

to the indications of and .

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote

control gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use different types together.

• Do not take apart the batteries, heat them, or throw them into a fire.

• When using the remote control in the wireless condition, be sure to unplug the remote cable from the REMOTE IN terminal on the monitor.

* The 1/8 Stereo Mini cable must be purchased separately.

En-7

Part Names and Function

Front View

INPUT SELECT

VOLUME

MENU/ENTER

DOWN UP LEFT/-RIGHT/+/EXIT

MENU/ENTER

VOLUME

DOWN UP LEFT/-RIGHT/

q Power

Turns the monitor’s power on and off.

w Remote sensor window

Receives the signals from the remote control.

e POWER/STANDBY indicator

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

r INPUT SELECT / EXIT

Switches the input. Functions as the EXIT buttons in the On-Screen Menu (OSM) mode.

INPUT SELECT

/EXIT

t LEFT/– and RIGHT/+

Functions as the CURSOR ( to adjust the picture parameters in the On-Screen Menu (OSM) mode.

y VOLUME DOWN and UP

Adjusts the volume. Functions as the CURSOR (▲/▼) buttons in the OnScreen Menu (OSM) mode.

u MENU/ENTER

Sets the On-Screen Menu (OSM) mode and displays the main menu.



/ ) buttons and used

WARNING

The Power on/off switch does not completely disconnect power from the display.

En-8

Rear View/ Terminal Board

42XM5

VIDEO

DVD

/ HD

RGB

/ DVD2 / HD

RGB

AUDIO

R/Cr/Pr G/Y B/ Cb/Pb

YL/R L/RCb/PbCr/Pr

AUDIO

RGB 3EXTERNAL CONTROL

(IN/OUT)

VD L/RHD

REMOTE

IN OUT

DVI

Y Cb/Pb Cr/Pr

)

AUDIO

DVD

R/Cr/Pr G/Y B/C b/Pb

(

)

MONO

AUDIO

VIDEO

(IN/OUT)

( MONO

CE F GHIJK

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct polarity. Connect the

EXT SPEAKER terminal and the (negative) speaker wire to the both LEFT and RIGHT channels. Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals. The input is selectable. Set which video image corresponds to the audio input from the audio menu screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

(positive) speaker wire to the

EXT SPEAKER terminal on

RGB

DVD

RGB

AUDIO

RGB

(IN/OUT)

(

)

Digital RGB

DVI

(

)

MONO

VDHD

EXTERNAL CONTROL

REMOTE

IN OUT

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output. This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally with a control system (by RS232C).

J REMOTE IN

Connect the remote cable to the remote control’s remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of the other display monitor to obtain wired remote control.

L Handles

Use when installing or carrying the plasma monitor.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc. here. This input can be set for use with an RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output.

En-9

Rear View/ Terminal Board

50XM6

VIDEO

DVD

RGB

DVD

HD2RGB

AUDIO

R/Cr/Pr G/Y B/ Cb/Pb

YL/R L/RCb/Pb Cr/Pr

AUDIO

RGB 3EXTERNAL CONTROL

(IN/OUT)

VD L/RHD

REMOTE

IN OUT

DVI

Y Cb/Pb Cr/Pr

)

AUDIO

DVD

R/Cr/Pr G/Y B/C b/Pb

(

)

MONO

AUDIO

VIDEO

(IN/OUT)

( MONO

CE F GHIJK

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct polarity. Connect the

EXT SPEAKER terminal and the (negative) speaker wire to the both LEFT and RIGHT channels. Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals. The input is selectable. Set which video image corresponds to the audio input from the audio menu screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

(positive) speaker wire to the

EXT SPEAKER terminal on

RGB

DVD

RGB

AUDIO

RGB

(IN/OUT)

(

)

Digital RGB

DVI

(

)

MONO

VDHD

EXTERNAL CONTROL

REMOTE

IN OUT

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output. This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally with a control system (by RS232C).

J REMOTE IN

Connect the remote cable to the remote control’s remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of the other display monitor to obtain wired remote control.

L Handles

Use when installing or carrying the plasma monitor.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc. here. This input can be set for use with an RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output.

En-10

Rear View/ Terminal Board

60XM5

DVD

/ HD

AUDIO

VIDEO

(IN/OUT)

Y Cb/Pb Cr/Pr

(

)

MONO

AUDIO

(

)

MONO

VIDEO

DVD

/ HD

AUDIO

YL/R L/RCb/Pb Cr/Pr

RGB

/ DVD2 / HD

R/Cr/Pr G/Y B/C b/Pb

AUDIO

RGB

/ DVD2 / HD

RGB

R/Cr/Pr G/Y B/ Cb/Pb

AUDIO

RGB 3EXTERNAL CONTROL

(IN/OUT)

VD L/RHD

RGB

VDHD

(IN/OUT)

REMOTE

IN OUT

DVI

AUDIO

RGB

(

)

DVI

Digital RGB

(

)

MONO

EXTERNAL CONTROL

REMOTE

IN OUT

CE F GHIJK

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct polarity. Connect the

EXT SPEAKER terminal and the (negative) speaker wire to the both LEFT and RIGHT channels. Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals. The input is selectable. Set which video image corresponds to the audio input from the audio menu screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

(positive) speaker wire to the

EXT SPEAKER terminal on

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output. This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally with a control system (by RS232C).

J REMOTE IN

Connect the remote cable to the remote control’s remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of the other display monitor to obtain wired remote control.

L Handles

Use when installing or carrying the plasma monitor.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc. here. This input can be set for use with an RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output.

En-11

Remote Control

q POWER ON/STANDBY

Switches the power on/standby. (This does not operate when the POWER/STANDBY indicator of the plasma is off.)

w RGB/PC

Press this button to select RGB/PC as the source. RGB/PC can also be selected using the INPUT SELECT button on the monitor.

e DVD / HD

Press this button to select DVD/HD as the source. DVD/HD can also be selected using the INPUT SELECT button on the monitor.

r VIDEO

Press this button to select VIDEO as the source.

→ VIDEO1 → VIDEO2 → VIDEO3

VIDEO can also be selected using the INPUT SELECT button on the monitor.

t MENU/ENTER

Press this button to access the OSM controls. Press this button during the display of the main menu to go to the sub menu.

y CURSOR (▲ / ▼ /

Use these buttons to select items or settings and to adjust settings or switch the display patterns.



/ )

u EXIT

Press this button to exit the OSM controls in the main menu. Press this button during the display of the sub menu to return to the previous menu.

i POINTER

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

!0 VOLUME (+ /–)

Adjusts the audio volume.

!1 MUTE

Mutes the audio.

!2 WIDE

Press this button to select and switch the screen sizes. WIDE button is not active for all signals.

!3 DISPLAY

Displays the source settings on the screen.

!4 OFF TIMER

Activates the off timer for the unit.

!5 SIDE BY SIDE

Press this button to show a couple of pictures in the side-by-side mode.

!6 PICTURE IN PICTURE

Press this button to show a couple of pictures in the picture-in-picture mode.

!7 SINGLE

Cancels the split screen mode.

!8 SELECT/FREEZE

Press this button to select the active picture in a split screen mode. When the PIC FREEZE function is operating, this button can be used to display still images on the sub screen.

!9 AUTO ADJUST

Press this button to adjust Fine Picture, Picture ADJ, Position, and Contrast automatically. Press this button in video mode and the Auto Adjust switches to ZOOM mode automatically when a letter box image is displayed.

@0 ID SELECT

Set the ID number in the remote control. The remote control can then be used only for a display with the same ID number. When several displays are used together they can be controlled individually.

@1 CLEAR/SEAMLESS SW

Clears the number set by the ID SELECT button. When the SEAMLESS SW function is operating, this button can be used to switch the input source quickly.

@2 Remote control signal transmitter

Transmits the remote control signals.

@3 Remote Jack

Insert the plug of the remote cable (The 1/8 Stereo Mini cable) here when using the supplied remote control in the wired condition.

En-12

Basic Operations

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

2. Press the Power button (on the unit). The monitor’s POWER/STANDBY indicator turns red and the standby mode is set.

3. Press the POWER ON button (on the remote control) to turn on the unit. The monitor’s POWER/STANDBY indicator will light up (green) when the unit is on.

Press the POWER STANDBY button (on the remote control)

4. or the Power button (on the unit) to turn off the unit. The monitor’s POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit with the remote control).

VOLUME

To adjust the sound volume:

1. Press and hold the VOLUME button (on the remote control or the unit) to increase to the desired level.

2. Press and hold the VOLUME control or the unit) to decrease to the desired level.

button (on the remote

MUTE

To mute the audio:

Press the MUTE button on the remote control to mute the audio; press again to restore.

DISPLAY

To check the settings:

1. Press the DISPLAY button to display the display mode.

2. If the button is not pressed for approximately three seconds, the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges the picture.

1. (Be sure ZOOM NAV is off.) Press the POINTER button to display the pointer. (

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture. The pointer will change to resemble a magnifying glass.

)

( A press of the ZOOM- button will reduce the picture and return it to its original size.

To change the picture position:

Select the position with the ▲▼

2. Press the POINTER button to delete the pointer.

 

buttons.

)

AUTO ADJUST

To adjust the size or quality of the picture automatically:

Press the AUTO ADJUST button.

OFF TIMER

To set the off timer:

The off timer can be set to turn the power off after 30, 60, 90 or 120 minutes.

1. Press the OFF TIMER button to start the timer at 30 minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

OFF TIMER 30

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER button once.

2. The remaining time is displayed, then turns off after a few seconds.

3. When five minutes remain the remaining time appears until it reaches zero.

OFF TIMER 28

To cancel the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

OFF TIMER 0

Note:

After the power is turned off with the off timer ... A slight current is still supplied to the monitor. When you are leaving the room or do not plan to use the system for a long period of time, turn off the power to the monitor.

Information

 AUTO ADJUST ON setting

When RGB (still picture) input is selected:

Fine Picture, Picture ADJ, Position, and Contrast will be adjusted automatically.

When RGB (motion picture), VIDEO, or Y/Pb/Pr (component) input is selected:

The screen size switches to ZOOM mode automatically when a letter box image is displayed.

En-13

WIDE Operations

Wide Screen Operation

With this function, you can select one of seven screen sizes.

(manual)

When viewing videos or digital video discs

1. Press the WIDE button on the remote control.

2. Within 3 seconds ... Press the WIDE button again. The screen size switches as follows:

→ NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN

When a 720P or 1080I signal is input:

FULL ↔ 2.35:1

When displaying enhanced split screen:

NORMAL ↔ FULL

NORMAL size screen (4:3)

The normal size screen is displayed. * The picture has the same size as video pictures with a 4 : 3

aspect ratio.

FULL size screen

2.35:1 size screen



Original image

Information is lost on both sides.

The squeezed film image is expanded to fulfill the entire screen at a ratio of 2.35:1. Black bands do not appear at the top and bottom but information is lost on the left and right margins.

• This feature is available when the input signal is video, component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB (525P or 625P signal from a scan converter).

* If black bands appear on the top and bottom in the full size

screen, select the 2.35:1 size screen to fill the screen and avoid image retention.

14:9 size screen

The image is displayed at a 14:9 aspect ratio. * This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P) or RGB (525P or 625P signal from a scan converter).

The image is expanded in the horizontal direction. * Images compressed in the horizontal direction (“squeezed

images”) are expanded in the horizontal direction and displayed on the entire screen with correct linearity. (Normal images are expanded in the horizontal direction.)

STADIUM size screen

The picture is expanded in the horizontal and vertical directions at different ratios. * Use this for watching normal video programs (4:3) with a

wide screen.

ZOOM size screen

UNDERSCAN size screen

Set “UNDERSCAN” to “ON” in the “IMAGE ADJUST”.

Typical televisions crop the image (i.e., overscan). In order to restore the entire image, select UNDERSCAN.

Overscan

* Picture noise or black border may appear near the edge of

screen depending on the connected component.

* The continuous display in this screen size over a prolonged

period of time may result in image retention.

* When Macrovision signal is input, the brightness may

change.

Note:

Do not allow 4:3 content to be displayed for extended periods of time without using gray bars. This can cause image retention.

Underscan

The picture is expanded in the horizontal and vertical direction, maintaining the original proportions. * Use this for theater size (wide) movies, etc.

En-14

Wide Screen Operation with Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image to fill the entire screen.

1. Press the WIDE button on the remote control.

2. Within 3 seconds ...

Press the WIDE button again. The screen size switches as follows:

→ NORMAL → FULL → ZOOM

When displaying enhanced split screen:

NORMAL ↔ FULL

NORMAL size screen (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

FULL size screen

The image is expanded in the horizontal and vertical direction.

ZOOM size screen

When wide signals are input.

TRUE

The image is expanded in the horizontal direction.

ZOOM size screen

When wide signals are input.

FULL size screen

When “PICTURE SIZE” is set to “OFF”

* This cannot be set in some models. “TRUE” size will not

be displayed in such cases.

The screen size switches as follows:

→ TRUE → FULL → ZOOM

TRUE size screen (VGA, SVGA 4:3)

The image is true resolution.

FULL

Information

 Supported resolution

See page En-42 for details on the display output of the various VESA signal standards supported by the monitor.

 “PICTURE SIZE” setting

When the setting of “PICTURE SIZE” is OFF, the size of RGB-input pictures will be TRUE in place of NORMAL.

 When 852 (848) dot  480 line wide VGA*

signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are input

Select an appropriate setting for RGB SELECT mode referring to the“Table of Signals Supported” on page En-42.

* “VGA”, “SVGA” and “SXGA” are registered

trademarks of IBM, Inc. of the United States.

The image is true resolution.

Note:

Do not allow 4:3 content to be displayed for extended periods of time without using gray bars. This can cause image retention.

En-15

VIDEO1 RGB1

VIDEO1RGB1

VIDEO1 RGB1

SPLIT SCREEN Operations

Showing a couple of pictures on the screen at the same time

* There may be some RGB-input signals that may not be

displayed as not all signals are supported.

1. Press the button to select a screen mode from among single mode, side-by-side, and picture-in-picture.

VIDEO1

SINGLE button

SIDE BY SIDE button

VIDEO1 RGB1

PICTURE IN PICTURE button

SIDE BY SIDE button

PICTURE IN PICTURE button

VIDEO1

Sub

screen

Note:

Picture A and B on the above screen are not always of the same height.

SINGLE button

RGB1

Main screen

Operations in the Side-by-side mode



button



To change the picture size, press the cursor   or button.

VIDEO1 RGB2

Side-by-Side2-R



button

VIDEO1 RGB2

Side-by-Side4-R



button



button

VIDEO1 RGB2



button

Side-by-Side1 Side-by-Side2-L



button



button

VIDEO1 RGB2



button

Side-by-Side3 Side-by-Side4-L



button



button



button



button



button

VIDEO1 RGB2



button

VIDEO1 RGB2

To swap the picture on the right and the left, press the



cursor

button.



button

Information

Split screen operations may not function depending on the combination of input signals. In the table below, “” means Yes, “” means No.

Pictures displayed on the right/main screen (Select1)

VIDEO2

VIDEO3





DVD/HD1





DVD/HD2

RGB1

RGB2















RGB3













Pictures

displayed on

the left/sub

screen

(Select2)

VIDEO1

VIDEO2

VIDEO3

DVD/HD1

DVD/HD2

RGB1

RGB2

RGB3

VIDEO1

 Split screen operations may not function

depending on the frequency of the RGB signals.

To make the desired picture active, press the SELECT/ FREEZE button.

SELECT/FREEZE button

En-16

Operations in the Picture-in-picture mode

To move the position of the sub screen, press the cursor or  button.

VIDEO1

RGB2

Top Left



button

VIDEO1 RGB2

Bottom Left Bottom Right



button



button



button



button



button

VIDEO1



button

VIDEO1 RGB2

Top Right

RGB2



button

Selecting the input signals to be displayed



1. Press the SELECT/FREEZE button to make the desired picture active.

2. Press the RGB/PC, VIDEO, or DVD/HD button. Each press of the button changes the selection of the input signal. The INPUT SELECT button on the monitor can also be used to change the selection.

Zooming in on a specific input

1. Press the SELECT/FREEZE button to make the desired picture active.

2. Use the POINTER button and the ZOOM/ button to enlage the picture. For details, see “DIGITAL ZOOM” on page En-13.

To change the size of the sub screen, press the

VIDEO1 RGB1



button.

VIDEO1 RGB1

 button

VIDEO1 RGB1

 button

VIDEO1 RGB1

 button

To make the desired picture active, press the SELECT/ FREEZE button.

VIDEO1 RGB1

SELECT/ FREEZE button

VIDEO1 RGB1

Adjusting the OSM controls

1. Press the SELECT/FREEZE button to make the desired picture active.

2. Press the MENU/ENTER button to display the MAIN MENU.

3. Adjust the setting to your preference. For details, see “OSM (On Screen Menu) Controls” on page En-18.

Note:

During enhanced split screen, some functions of OSM controls are not available.

En-17

OSM (On Screen Menu) Controls

Menu Operations

The OSM window is displayed with respect to the screen as shown on the diagram.

* Depending on the screen’s mode, the OSM may be

displayed differently. In the explanation, the OSM section is shown close up.

MAIN MENU 1 / 2 PICTURE AUDIO IMAGE ADJUST OPTION1

ADVANCED OSM

: OFF

MENU/ENTEROKEXIT

SEL.

The following describes how to use the menus and the selected items.

1. Press the MENU/ENTER button on the remote control to display the MAIN MENU.

EXIT

MAIN MENU 1 / 2 PICTURE AUDIO IMAGE ADJUST OPTION1

ADVANCED OSM

MENU/ENTEROKEXIT

SEL.

MAIN MENU 2 / 2 PREVIOUS PAGE LANGUAGE COLOR SYSTEM SOURCE INFORMATION

: OFF

EXIT

Note:

The main menu disappears by pressing the EXIT

button.

Information

 Advanced menu mode

When “ADVANCED OSM” is set to “ON” in the main menu (1/2), full menu items will be shown.

MAIN MENU 1 / 2 PICTURE AUDIO IMAGE ADJUST OPTION1 OPTION2 OPTION3 OPTION4 ADVANCED OSM

MENU/ENTEROKEXIT

SEL.

: ON

EXIT

* The actual screen may be different from the ones in

this manual.

MENU/ENTEROKEXIT

SEL.

EXIT

2. Press the cursor buttons ▲ ▼ on the remote control to

highlight the menu you wish to enter.

3. Press the MENU/ENTER button on the remote control to select a sub menu or item.

CONTRAST BRIGHTNESS SHARPNESS COLOR TINT PICTURE MODE NR

SEL. ADJ. RETURN

PICTURE 1 / 2

: NORMAL : OFF

EXIT

: 52 : 32 : 16 : 32

: 32

4. Adjust the level or change the setting of the selected item

 

by using the cursor buttons

on the remote control.

5. The adjustments or settings are then stored in memory. The change is stored until another change is made.

6. Repeat steps 2 – 5 to adjust an additional item, or press the EXIT button on the remote control to return to the main menu.

* When adjusting using the bar at the bottom of the screen,



press the

or  button within 5 seconds. If not, the

current setting is stored and the previous screen appears.

En-18

Menu Tree

:Shaded areas indicate the default value.

←→

: Press the

:Menu items in a ruled box are available when the ADVANCED OSM is set to ON.

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

PICTURE CONTRAST ←→ 0←52→72 YES YES En-21

BRIGHTNESS ←→ 0←32→64 YES YES En-21 SHARPNESS ←→ 0←16→32 YES YES En-21 COLOR ←→ 0←32→64 YES YES En-21 TINT R←→G 0←32→64 YES YES En-21 PICTURE MODE BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT YES YES En-21 NR OFF/NR-1/NR-2/NR-3 YES YES En-21 COLOR TEMP. LOW/MID LOW/MID/HIGH YES YES En-21 WHITE BALANCE GAIN RED ←→ 0←40→70 YES NO En-22

GAMMA 1←→2←…→4 YES NO En-22 LOW TONE * COLOR TUNE RED Y←→M0←32→64 YES NO En-22



or  button to adjust.

GAIN GREEN ←→ 0←40→70 YES NO En-22 GAIN BLUE ←→ 0←40→70 YES NO En-22 BIAS RED ←→ 0←40→70 YES NO En-22 BIAS GREEN ←→ 0←40→70 YES NO En-22 BIAS BLUE ←→ 0←40→70 YES NO En-22 RESET OFF←→ON YES NO En-22

MODE1←→MODE2 YES NO En-22

GREEN C←→Y0←32→64 YES NO En-22 BLUE M←→C0←32→64 YES NO En-22 YELLOW G←→R0←32→64 YES NO En-22 MAGENTA R←→B0←32→64 YES NO En-22 CYAN B←→G0←32→64 YES NO En-22 RESET OFF←→ON YES NO En-22

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

AUDIO BASS ←→ 0←13→26 YES YES En-23

TREBLE ←→ 0←13→26 YES YES En-23 BALANCE L←→R -22←0→+22 YES YES En-23 AUDIO INPUT1 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23 AUDIO INPUT2 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23 AUDIO INPUT3 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

IMAGE ADJUST ASPECT MODE NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE*

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION1 OSM DISPLAY OSM OFF←→ON YES YES En-24

V-POSITION ←→ -64←0→+64 YES YES En-23 H-POSITION ←→ -128←0→+127 YES YES En-23 V-HEIGHT ←→ 0←→64 YES YES En-23 H-WIDTH ←→ 0←→64 YES YES En-23 AUTO PICTURE OFF←→ON* FINE PICTURE* PICTURE ADJ.* UNDERSCAN OFF←→ON YES NO En-23

BNC INPUT RGB←→COMP. YES YES En-24 D-SUB INPUT RGB — YES En-24 RGB SELECT AUTO YES YES En-24 HD SELECT 1080B/1035I/1080A NO YES En-25 INPUT SKIP OFF←→ON YES YES En-25 ALL RESET OFF←→ON — YES En-25

←→*20←→64 YES YES En-23

OSM ADJ. 1←…→6 YES YES En-24 OSM ANGLE H←→V YES YES En-24 OSM ORBITER OFF←→ON YES YES En-24 OSM CONTRAST LOW←→NORMAL YES YES En-24

— YES En-23

NO YES En-23

En-19

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION2 PWR. MGT. OFF←→ON YES NO En-26

CINEMA MODE OFF←→ON YES NO En-26 LONG LIFE PLE AUTO/LOCK 1/LOCK 2/LOCK 3 YES NO En-26

ORBITER AUTO 1 YES NO En-27

INVERSE OFF YES NO En-27

SCREEN WIPER OFF YES NO En-28

SOFT FOCUS OFF/1/2/3/4 YES NO En-28 GRAY LEVEL 0←…→3←…→15 YES NO En-28 S1/S2 AUTO←→OFF YES NO En-29 PICTURE SIZE* DVI SET UP PLUG/PLAY PC←→STB/DVD NO NO En-29

PROTOCOL SET OFF←→ON YES NO En-29 CLOSECAPTION OFF←→CC1~4←→TEXT1~4 YES NO En-30 CAPTION CONT LOW←→NORMAL YES NO En-30

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION3 TIMER PRESENT TIME

PWR. ON MODE INPUT LAST /MULTI/ VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES NO En-32

CONTROL LOCK OFF←→ON YES NO En-32 IR REMOTE OFF←→ON YES NO En-33 LOOP OUT OFF←→ON YES NO En-33 REMOTE ID ALL←→1←…→4 NO NO En-33 ID NUMBER ALL←→1←…→256 YES NO En-33 VIDEO WALL DIVIDER OFF/1/22/33/44/55/51/15 YES NO En-34

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION4 SUB. PICTURE SUB. P DETECT OFF←→AUTO YES NO En-36

ZOOM NAV OFF←→S BY S←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT YES NO En-36 PIC FREEZE OFF←→S BY S1←→S BY S2←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT YES NO En-36 SEAMLESS SW OFF YES NO En-37

TEXT INSERT OFF/BOTTOM-1/BOTTOM-2/BOTTOM-3/MID. LOW/MID. HIGH/TOP-3/TOP-2/TOP-1/LEFT/RIGHT YES NO En-37

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

ADVANCED OSM OFF←→ON YES NO En-38 LANGUAGE ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/У/PORTUGUÊS NO NO En-38 COLOR SYSTEM AUTO/3.58 NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM NO YES En-38 SOURCE INFORMATION

— — YES En-38

OFF←→ON YES NO En-29

BLACK LEVEL LOW←→HIGH NO NO En-29

TIMER OFF YES NO En-31

VOLUME LAST←→0←…→42 YES NO En-32

POSITION

DISP. MODE SPLIT←→BLANK YES NO En-34

AUTO ID OFF←→ON YES NO En-34

IMAGE ADJUST ASPECT MODE

P. ON DELAY OFF/ON/MODE1/MODE2 YES NO En-35

PLE LINK OFF←→ON YES NO En-35

SUB. P RATE 20%←…→100% YES NO En-36

DISPLAY FADE←→NORMAL YES NO En-36

ON SELECT1/SELECT2 YES NO En-37

AUTO 2 YES NO En-27 MANUAL H-DOT/V-LINE/TIME YES NO En-27 OFF YES NO En-27

ON WORKING TIME/WAITING TIME YES NO En-27 WHITE YES NO En-27

ON WORKING TIME/WAITING TIME/SPEED YES NO En-28

DAYLIGHT SAVING TIME DAY/HOUR/MINUTES NO NO En-30

PROGRAM DAY/ON/OFF(HOUR, MINUTES)/INPUT/FUNC. YES NO En-31 REPEAT SINGLE/MULTI/VIDEO-W YES NO En-31

No.1←…→No.4/No.7←…→No.15/No.16←…→No.31/No.32←…→No.56

V-POSITION/H-POSITION/V-HEIGHT/H-WIDTH/AUTO PICTURE/ FINE PICTURE*

INPUT/SUB. P DETECT/PIC. RATE/DISPLAY YES NO En-37

OFF←→ON NO NO En-30

— NO En-34

NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE

/PICTURE ADJ.*1/UNDERSCAN

*3— NO En-35

*1 Only when AUTO PICTURE is OFF. *2 RGB only. *3 “PICTURE SIZE” and “TRUE” are only for 50 and 60 inch types. *4 “LOW TONE” is only for 50 inch type.

Information

 Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

En-20

Picture Settings Menu

Adjusting the picture

The contrast, brightness, sharpness, color and tint can be adjusted as desired.

Example: Adjusting the contrast

On “CONTRAST” of “PICTURE” menu, adjust the contrast.

CONTRAST BRIGHTNESS SHARPNESS COLOR TINT PICTURE MODE NR

SEL. ADJ. RETURN

PICTURE 1 / 2

: NORMAL : OFF

EXIT

: 52 : 32 : 16 : 32

: 32

CONTRAST

Reducing noise in the picture

Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor.

Example: Setting “NR-3”

On “NR” of “PICTURE” menu, select “NR-3”.

CONTRAST BRIGHTNESS SHARPNESS COLOR TINT PICTURE MODE NR

SEL. ADJ. RETURN

PICTURE 1 / 2

: NORMAL : OFF

EXIT

: 52 : 32 : 16 : 32

: 32

NR-3

Note:

If “CAN NOT ADJUST” appears ... When trying to enter the PICTURE submenu, make sure PICTURE MODE is not set to DEFAULT.

Information

 Picture adjustment screen

CONTRAST: Changes the picture’s white level. BRIGHTNESS:

Changes the picture’s black level.

SHARPNESS: Changes the picture’s sharpness. Adjusts picture detail of VIDEO display.

COLOR: Changes the color density. TINT: Changes the picture’s tint. Adjust for natural

colored skin, background, etc.

 Adjusting the computer image

Only the contrast and brightness can be adjusted when a computer signal is connected.

 Restoring the factory default settings

Select “DEFAULT” under the “PICTURE MODE” settings.

Setting the picture mode according to the brightness of the room

There are four picture modes that can be used effectively according to the environment in which you are viewing the display.

Example: Setting the “THEAT. 1” mode

On “PICTURE MODE” of “PICTURE” menu, select “THEAT. 1”.

CONTRAST BRIGHTNESS SHARPNESS COLOR TINT PICTURE MODE NR

SEL. ADJ. RETURN

PICTURE 1 / 2

: NORMAL : OFF

EXIT

: 52 : 32 : 16 : 32

: 32

PICTURE MODE

THEAT. 1

Information

 NR

* “NR” stands for Noise Reduction. * This function reduces noise in the picture.

 Types of noise reduction

There are three types of noise reduction. Each has a different level of noise reduction. The effect becomes stronger as the number increases (in the order NR-1 → NR-2 → NR-3). OFF: Turns the noise reduction function off.

Setting the color temperature

Use this procedure to set color tone produced by the plasma display.

Example: Setting “HIGH”

On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”.

PREVIOUS PAGE COLOR TEMP. GAMMA LOW TONE COLOR TUNE

SEL. ADJ. RETURN

PICTURE 2 / 2

: HIGH : 2 : MODE1

EXIT

Information

 Setting the color temperature

LOW: More red MID LOW: Slightly red MID: Standard (slightly bluer) HIGH: More blue

Information

 Types of picture modes

THEAT. 1, 2: Set this mode when watching video in a dark room. This mode provides darker, finer pictures, like the screen in movie theaters. For a darker image, select THEAT. 2. NORMAL: Set this mode when watching video in a bright room. BRIGHT: This mode provides brighter pictures than NORMAL. This mode provides dynamic pictures with distinct differences between light and dark sections. DEFAULT: Use this to reset the picture to the factory default settings.

En-21

Adjusting the color to the desired level

Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality.

Example: Adjusting the “GAIN RED” of “HIGH” color temperature

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”, then press the MENU/ENTER button. The “WHITE BALANCE” screen appears.

On “GAIN RED”, adjust the white balance.

WHITE BALANCE

COLOR TEMP. HIGH GAIN RED GAIN GREEN GAIN BLUE BIAS RED BIAS GREEN BIAS BLUE RESET

SEL. ADJ. RETURN

: OFF

EXIT

: 40 : 40 : 40 : 40 : 40 : 40

GAIN RED

Information

 Adjusting the white balance

GAIN R/G/B: White balance adjustment for white level. BIAS R/G/B: White balance adjustment for black level. RESET: Resets settings to the factory default values.



Use

and  buttons to select “ON”, then press the

MENU/ENTER button.  Restoring the factory default settings Select “RESET” under the WHITE BALANCE menu.

Changing the Gamma Curve

This feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged.

Example: Setting “3”

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

On “GAMMA” of “PICTURE” menu, select “3”.

PREVIOUS PAGE COLOR TEMP. GAMMA LOW TONE COLOR TUNE

SEL. ADJ. RETURN

PICTURE 2 / 2

: MID : 3 : MODE1

EXIT

Information

 GAMMA settings

The picture becomes darker as the number increases (in the sequence of 1, 2, 3, 4).

Making the Low Tone adjustments

You can select the tone reproduction from 2 modes. This function is effective especially for dark images. * This function is available only for 50 inch type.

Example: Setting “MODE2”

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

On “LOW TONE” of “PICTURE” menu, select “MODE2”.

PREVIOUS PAGE COLOR TEMP. GAMMA LOW TONE COLOR TUNE

SEL. ADJ. RETURN

PICTURE 2 / 2

: MID : 2 : MODE2

EXIT

Adjusting the colors

Use this procedure to adjust hue and color density for red, green, blue, yellow, magenta and cyan without changing the white point. You can accentuate the green color of trees, the blue of the sky, etc.

Example: Adjusting the color tune for blue

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

On “PICTURE” menu, select “COLOR TUNE”, then press the MENU/ENTER button. The “COLOR TUNE” screen appears.

On “BLUE” of “COLOR TUNE”, adjust the color tune.

RED GREEN BLUE YELLOW MAGENTA CYAN RESET

SEL. ADJ. RETURN

COLOR TUNE

: OFF

EXIT

: 32

Information

 COLOR TUNE settings

RED: Adjusts hue of Red GREEN: Adjusts hue of Green BLUE: Adjusts hue of Blue YELLOW: Adjusts hue of Yellow MAGENTA: Adjusts hue of Magenta CYAN: Adjusts hue of Cyan RESET: Resets settings to the factory default value.



and  buttons to select “ON”, then press the

Use MENU/ENTER button.

En-22

Audio Settings Menu

Adjusting the treble, bass and left/right balance and audio input select

The treble, bass and left/right balance can be adjusted to suit your tastes.

Example: Adjusting the bass

On “BASS” of “AUDIO” menu, adjust the bass.

Note :

BASS TREBLE BALANCE AUDIO INPUT1 AUDIO INPUT2 AUDIO INPUT3

SEL. ADJ. RETURN

AUDIO

: VIDEO1 : DVD/HD1 : RGB1

EXIT

If “CAN NOT ADJUST” appears...

: 26 : 13

: ±0

Set “AUDIO INPUT” on the AUDIO menu correctly.

Information

 Audio settings menu

BASS: Controls the level of low frequency sound. TREBLE: Controls the level of high frequency sound. BALANCE: Controls the balance of the left and right

channels.

Setting the allocation of the audio connectors

Setting the AUDIO 1, 2, and 3 connectors to the desired input.

Example: Setting “AUDIO INPUT1” to “VIDEO2”

On “AUDIO INPUT1” of “AUDIO” menu, select “VIDEO2”.

The available sources depend on the settings of input.

BASS TREBLE BALANCE AUDIO INPUT1 AUDIO INPUT2 AUDIO INPUT3

SEL. ADJ. RETURN

AUDIO

: VIDEO2 : DVD/HD1 : RGB1

EXIT

: 13 : 13

: ±0

Information

 AUDIO INPUT

A single audio input cannot be selected as the audio channel for more than one input terminal.

Image Adjust Settings Menu

Adjusting the Position, Size, Fine Picture, Picture Adj and Underscan

The position of the image can be adjusted and flickering of the image can be corrected.

Example: Adjusting the vertical position in the normal mode

On “V-POSITION” of “IMAGE ADJUST” menu, adjust the position.



The mode switches as follows each time the pressed:

NORMAL ↔ FULL

* The mode can also be switched by pressing the WIDE

button on the remote control.

* The settings on the IMAGE ADJUST menu are not preset

at the factory.

or  button is

ASPECT MODE V-POSITION H-POSITION V-HEIGHT H-WIDTH AUTO PICTURE FINE PICTURE PICTURE ADJ. UNDERSCAN

IMAGE ADJUST

: NORMAL

: OFF

SEL. ADJ. RETURN

EXIT

: ±0 : ±0 : 0 : 0

: 0 : 0

V-POSITION

Information

 When “AUTO PICTURE” is “OFF”

ASPECT MODE V-POSITION H-POSITION V-HEIGHT H-WIDTH AUTO PICTURE FINE PICTURE PICTURE ADJ. UNDERSCAN

SEL. ADJ. RETURN

IMAGE ADJUST

: FULL

: OFF

EXIT

: ±0 : ±0 : 32 : 32

: 32 : 32

When Auto Picture is off, the Fine Picture and the Picture ADJ. items are displayed so that you can adjust them.

 Adjusting the Auto Picture

ON: The Picture ADJ., Fine Picture and Position adjustments are made automatically. Not available for digital ZOOM. OFF: The Picture ADJ., Fine Picture and Position adjustments are made manually.

* If FINE PICTURE can’t be adjusted, set Auto Picture

to OFF and adjust manually.

 Adjusting the position of the image

V-POSITION: Adjusts the vertical position of the image. H-POSITION: Adjusts the horizontal position of the image. V-HEIGHT: Adjusts the vertical size of the image. (Not available for STADIUM mode) H-WIDTH: Adjusts the horizontal size of the image. (Not available for STADIUM mode)

FINE PICTURE*: Adjusts for flickering. PICTURE ADJ.*: Adjusts for striped patterns on the

image (i.e. vertical banding).

* The Picture ADJ. and Fine Picture features are available

only when the “Auto Picture” is off.

* The AUTO PICTURE, FINE PICTURE and PICTURE

ADJ. are available only for RGB signals. But, these features are not available for moving pictures on VIDEO, DVD/HD or RGB.

 Setting the Underscan

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

ON: UNDERSCAN can be selected in ASPECT MODE. OFF: UNDERSCAN cannot be selected in ASPECT MODE.

* Selectable only when video signal is input.

En-23

Option1 Settings Menu

Setting the on-screen menu

This sets the position of the menu, the display format (horizontal or vertical) etc.

Example: Turning the DISPLAY OSM off

On “OPTION1” menu, select “OSM”, then press the MENU/ ENTER button. The “OSM” menu appears.

On “DISPLAY OSM” of “OSM” menu, select “OFF”.

DISPLAY OSM OSM ADJ. OSM ANGLE OSM ORBITER OSM CONTRAST

SEL. ADJ. RETURN

Information

 DISPLAY OSM settings

ON: The informations on screen size, volume control, etc. will be shown. OFF: The informations on screen size, volume control, etc. will not be shown. The DISPLAY button on the remote control will not function either.

 OSM ADJUST settings

Adjusts the position of the menu when it appears on the screen. The position can be set between 1 to 6.

OSM

: OFF : 1 : H : OFF : LOW

EXIT

Setting the BNC input connector type

Select whether to set the input of the 5 BNC connectors to RGB or Component.

Example: Set the “BNC INPUT” mode to “COMP.”

On “BNC INPUT” of “OPTION1” menu, select “COMP.”.

OSM BNC INPUT D-SUB INPUT RGB SELECT : AUTO HD SELECT INPUT SKIP ALL RESET

SEL. ADJ. RETURN

OPTION1 1 / 4

: COMP. : RGB

: 1080B : OFF : OFF

EXIT

Information

 BNC INPUT Settings

RGB: Use the 5BNC terminals for RGB input. COMP.: Use the 3BNC terminals for component input.

Checking the signal being transmitted to RGB1 terminal

Use this to confirm the signal being transmitted to the RGB1 terminal. It is set to RGB and can not be adjusted.

OSM BNC INPUT D-SUB INPUT RGB SELECT : AUTO HD SELECT INPUT SKIP ALL RESET

CAN NOT ADJUST

OPTION1 1 / 4

: RGB : RGB

: 1080B : OFF : OFF

 OSM ANGLE settings

Sets the display format (landscape “H” or portrait “V”). When the unit is installed vertically set the OSM ANGLE at “V”.

“H”“V”

OPTION1 1 / 4 OSM BNC INPUT

: RGB

D-SUB INPUT

: RGB

RGB SELECT

: AUTO

HD SELECT

: 1080B

INPUT SKIP

: OFF

ALL RESET

: OFF

MENU/ENTER

SEL. RETURN

EXIT

OPTION1

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

SEL.

MENU/ENTER

: RGB

: AUTO

: 1080B

: OFF

: OFF 1024768

EXIT

RETURN

* The menu language for “V” is English only. * Some menu items including LONG LIFE mode will

not be displayed with “V”, but can be performed by setting with “H” (See pages 19 and 20 for the menu items that can be displayed with “V”).

 OSM ORBITER settings

ON: The position of the menu will be shifted by eight dots each time OSM is displayed. OFF: OSM will be displayed at the same position.

 OSM CONTRAST settings

NORMAL: OSM brightness is set to normal. LOW: OSM brightness is set to lower.

Setting a computer image to the correct RGB select screen

With the computer image, select the RGB Select mode for a moving image such as (video) mode, wide mode or digital broadcast.

Example: Setting the “RGB SELECT” mode to “852480 ”

On “RGB SELECT” of “OPTION1” menu, select “852480”.

OSM BNC INPUT D-SUB INPUT RGB SELECT : 852480 HD SELECT INPUT SKIP ALL RESET

SEL. ADJ. RETURN

OPTION1 1 / 4

: RGB : RGB

: 1080B : OFF : OFF

EXIT

Information

 RGB SELECT modes

AUTO: Select the suitable mode for the specifications of input signals as listed in the table “Computer input signals supported by this system” on page En-42. The others: The available resolutions are shown.

See page En-42 for the details of the above settings.

En-24

Setting high definition images to the suitable screen size

Use this procedure to set whether the number of vertical lines of the input high definition image is 1035 or 1080.

Example: Setting the “HD SELECT” mode to “1035I”

On “HD SELECT” of “OPTION1” menu, select “1035I”.

OSM BNC INPUT D-SUB INPUT RGB SELECT : AUTO HD SELECT INPUT SKIP ALL RESET

SEL. ADJ. RETURN

OPTION1 1 / 4

: RGB : RGB

1035

: : OFF : OFF

EXIT

Information

 HD SELECT modes

These 3 modes are not displayed in correct image automatically.

1080B: Standard digital broadcasts 1035I: Japanese “High Vision” signal format 1080A: Special Digital broadcasts (for example :

DTC100)

Setting the Input Skip

When this is ON, signals which are not present will be skipped over and only pictures whose signals are being transmitted will be displayed. This setting is valid only for the INPUT SELECT button on the unit.

Example: Set to “ON”

On “INPUT SKIP” of “OPTION1” menu, select “ON”.

OSM BNC INPUT D-SUB INPUT RGB SELECT : AUTO HD SELECT INPUT SKIP ALL RESET

SEL. ADJ. RETURN

OPTION1 1 / 4

: RGB : RGB

1080B

: : ON : OFF

EXIT

Resetting to the default values

Use these operations to restore all the settings (PICTURE, AUDIO, IMAGE ADJUST, OPTION1~4, etc.) to the factory default values.

Refer to page En-19 for items to be reset.

On “ALL RESET” of “OPTION1” menu, select “ON”, then press the MENU/ENTER button.

OSM BNC INPUT D-SUB INPUT RGB SELECT : AUTO HD SELECT INPUT SKIP ALL RESET

SEL. RETURN

OPTION1 1 / 4

: RGB : RGB

1080B

: : OFF : ON

MENU/ENTER

EXIT

ALL RESET

SETTING NOW

When the “SETTING NOW” screen disappears, then all the settings are restored to the default values.

Information

 INPUT SKIP settings

OFF: Regardless of the presence of the signal, scan and display all signals. ON: If no input signal is present, skip that signal.

* “SETTING NOW” will appear during the input search.

En-25

Option2 Settings Menu

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

Setting the power management for computer images

This energy-saving (power management) function automatically reduces the monitor’s power consumption if no operation is performed for a certain amount of time.

Example:

On “PWR. MGT.” of “OPTION2” menu, select “ON”.

Information

䡵 Power management function

* The power management function automatically reduces

the monitor’s power consumption if the computer’s keyboard or mouse is not operated for a certain amount of time. This function can be used when using the monitor with a computer.

* If the computer’s power is not turned on or if the

computer and selector tuner are not properly connected, the system is set to the off state.

* For instructions on using the computer’s power

management function, refer to the computer’s operating instructions.

䡵 Power management settings

ON: In this mode the power management function is turned on. OFF: In this mode the power management function is turned off.

䡵 Power management function and POWER/

The POWER/STANDBY indicator indicates the status of the power management function. See below for indicator status and description.

POWER/STANDBY indicator

Power management mode

Off

Turning the power management function on

PREVIOUS PAGE PWR. MGT. CINEMA MODE LONG LIFE GRAY LEVEL S1/S2 PICTURE SIZE DVI SET UP PROTOCOL SET CLOSECAPTION CAPTION CONT NEXT PAGE

SEL. ADJ. RETURN

OPTION2 2 / 4

: ON : ON

: 3 : OFF : ON

: OFF : OFF : LOW

EXIT

STANDBY indicator

POWER/ STANDBY indicator

Green

Red

Power management operating status

Not activated.

Activated.

Description

Horizontal and vertical synchronizing signals are present from the computer.

Horizontal and/or vertical synchronizing signals are not sent from the computer.

Turning the picture back on

Picture already on.

Operate the keyboard or mouse. The picture reappears.

Setting the picture to suit the movie

The film image is automatically discriminated and projected in an image mode suited to the picture. [NTSC, PAL, PAL60, 480I (60 Hz), 525I (60 Hz), 576I (50 Hz), 625I (50 Hz), 1035I (60 Hz), 1080I (60 Hz) only]

Example: Setting the “CINEMA MODE” to “OFF”

On “CINEMA MODE” of “OPTION2” menu, select “OFF”.

PREVIOUS PAGE PWR. MGT. CINEMA MODE LONG LIFE GRAY LEVEL S1/S2 PICTURE SIZE DVI SET UP PROTOCOL SET CLOSECAPTION CAPTION CONT NEXT PAGE

SEL. ADJ. RETURN

OPTION2 2 / 4

: OFF : OFF

: 3 : OFF : ON

: OFF : OFF : LOW

EXIT

Information

䡵 CINEMA MODE

ON: Automatic discrimination of the image and projection in cinema mode. OFF: Cinema mode does not function.

Reducing image retention

The brightness of the screen, the position of the picture, positive/negative mode and screen wiper are adjusted to reduce image retention.

On “OPTION2” menu, select “LONG LIFE”, then press the MENU/ENTER button. The “LONG LIFE” screen appears.

PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS

SEL. ADJ. RETURN

LONG LIFE

: AUTO : AUTO1 : OFF : OFF : OFF

EXIT

PLE (Peak Luminance Enhancement)

Use this to activate the brightness limiter.

Example: Setting “PLE” to “LOCK1”

On “PLE” of “LONG LIFE” menu, select “LOCK1”.

PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS

SEL. ADJ. RETURN

LONG LIFE

: LOCK1 : AUTO1 : OFF : OFF : OFF

EXIT

Information

䡵 PLE settings

AUTO: The brightness of the screen is adjusted automatically to suit the picture quality. LOCK1, 2, 3: Sets maximum brightness. The brightness level decreases in the order of LOCK 1, 2, 3. LOCK 3 provides minimum brightness.

En-26

ORBITER

Use this to set the picture shift.

Example: Setting “ORBITER” to “AUTO2”

On “ORBITER” of “LONG LIFE” menu, select “AUTO2”.

PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS

SEL. ADJ. RETURN

LONG LIFE

: AUTO : AUTO2 : OFF : OFF : OFF

EXIT

Information

䡵 ORBITER settings

OFF: Orbiter mode does not function. This is the default setting when RGB is input. AUTO1: The picture moves around the screen intermittently, making the picture smaller. This is the default setting when a Video or a DVD/HD/DTV signal is input. Set to “OFF” when these signals are not used. AUTO2: The picture moves around the screen intermittently, making the picture bigger. MANUAL: User can adjust the orbiter function (Horizontal Dot, Vertical Line and Time) manually. See the following explanation.

* When a Video or a DVD/HD/DTV signal is input, the

AUTO1 and 2 functions will affect only the moving picture and will not make the screen smaller or bigger.

Adjust the ORBITER function manually

Set the amount of shift and the time between movement.

Example: Setting so that the picture moves 2 dots horizontally and 4 lines vertically every 3 minutes.

On “ORBITER” of “LONG LIFE” menu, select “MANUAL”, then press the MENU/ENTER button.

THE “ORBITER” screen appears. Adjust the items.

H-DOT V-LINE TIME

SEL. ADJ. RETURN

ORBITER

: 2DOT : 4LINE : 3M

EXIT

Information

䡵 ORBITER Function settings

H-DOT: Moves from 1 dot to 20 dots in the horizontal direction. V-LINE: Moves from 1 line to 20 lines in the vertical direction. TIME: Interval of 1 minute to 5 minutes (1 horizontal dot or 1 vertical line per interval).

INVERSE

Use this to set the inverse mode or to display a white screen.

Example: Setting “INVERSE” to “WHITE”

On “INVERSE” of “LONG LIFE” menu, select “WHITE”.

PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS

SEL. ADJ. RETURN

LONG LIFE

: AUTO : AUTO1 : WHITE : OFF : OFF

EXIT

Information

䡵 INVERSE Settings

ON: The picture is displayed alternately between positive image and negative image. You can set the time by pressing the MENU/ENTER button while “ON” is set.

OFF: Inverse mode does not function. WHITE: The entire screen turns white.

You can set the time by pressing the MENU/ENTER button while “ON” is set.

Setting the time for INVERSE/WHITE

Set a time duration.

Example: Setting to that the INVERSE mode starts in 2 hours and proceeds for one hour and a half.

On “INVERSE” of “LONG LIFE” menu, select “ON”, then press the MENU/ENTER button. THE “INVERSE/WHITE” screen appears.

Adjust the times.

WORKING TIME WAITING TIME

INVERSE/WHITE

SEL. ADJ. RETURN

: 01H30M : 02H00M

EXIT

Information

䡵 Setting the time

WORKING TIME: Set the time duration for

“INVERSE/WHITE”. When the WORKING TIME is set to “ON” the mode will stay on. WAITING TIME: Set the standby time until the “INVERSE/WHITE” mode starts.

* The “WAITING TIME” can not be set when the

“WORKING TIME” is ON. THE “WORKING TIME” and “WAITING TIME” can be

set for up to 12 hours and 45 minutes in units of 3 minutes.

* Ending a WORKING TIME function, the monitor will

go to STANDBY.

[Example]

WORKING TIME: 01H30M WAITING TIME: 02H00M

←−−−− 2 H −−−−→←−− 1.5 H −−→←−−−−

Start INVERSE/WHITE Start STANDBY

䡵 To select “ON” for the “WORKING TIME”...

Set the hours of the working time to 0H and the minutes to 0M. “ON” will be displayed.

En-27

SCREEN WIPER

When this is set to ON, a white vertical bar moves repeatedly from the left and of the screen to the right end at a constant speed.

Example: Setting “SCREEN WIPER” to “ON”

On “SCREEN WIPER” of “LONG LIFE” menu, select “ON”.

PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS

SEL. ADJ. RETURN

LONG LIFE

: AUTO : AUTO1 : OFF : ON : OFF

EXIT

Information

䡵 SCREEN WIPER

ON: The white vertical bar appears. You can set the time by pressing the MENU/ENTER button while “ON” is set.

OFF: Screen wiper mode does not function.

Setting the time for SCREEN WIPER

Set a time duration and the speed.

Example: Setting so that the SCREEN WIPER mode starts in 30 minutes and proceeds for one and a half hours.

On “SCREEN WIPER” of “LONG LIFE” menu, select “ON”, then press the MENU/ENTER button.

THE “SCREEN WIPER” screen appears. Adjust the times and speed.

WORKING TIME WAITING TIME SPEED

SCREEN WIPER

SEL. ADJ. RETURN

: 01H30M : 00H30M : 3

EXIT

Information

䡵 Setting the time

WORKING TIME: Set the time duration for “SCREEN WIPER”. When the WORKING TIME is set to “ON” the mode will stay on. WAITING TIME: Set the standby time until the “SCREEN WIPER” mode starts. SPEED: Set the moving speed for the “SCREEN WIPER”. The speed decreases as the number increases.

* The “WAITING TIME” can not be set when the

“WORKING TIME” is ON.

* THE “WORKING TIME” and “WAITING TIME” can

be set for up to 12 hours and 45 minutes in units of 3 minutes.

䡵 To select “ON” for the “WORKING TIME”...

Set the hours of the working time to 0H and the minutes to 0M. “ON” will be displayed.

SOFT FOCUS

Reduces edges and softens the image.

Example: Setting “SOFT FOCUS” to “2”

On “SOFT FOCUS” of “LONG LIFE” menu, select “2”.

PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS

SEL. ADJ. RETURN

LONG LIFE

: AUTO : AUTO1 : OFF : OFF : 2

EXIT

Information

䡵 SOFT FOCUS settings

OFF: Turns the SOFT FOCUS function off. 1, 2, 3, 4: Activates the SOFT FOCUS setting. The

higher numbers create a softer image. “SHARPNESS” can not be adjusted in the “PICTURE” menu.

Setting the gray level for the sides of the screen

Use this procedure to set the gray level for the parts on the screen on which nothing is displayed when the screen is set to the 4:3 size.

Example: Setting “GRAY LEVEL” to “5”

On “GRAY LEVEL” of “OPTION2” menu, select “5”.

PREVIOUS PAGE PWR. MGT. CINEMA MODE LONG LIFE GRAY LEVEL S1/S2 PICTURE SIZE DVI SET UP PROTOCOL SET CLOSECAPTION CAPTION CONT NEXT PAGE

SEL. ADJ. RETURN

OPTION2 2 / 4

: OFF : ON

: 5 : OFF : ON

: OFF : OFF : LOW

EXIT

Information

䡵 GRAY LEVEL settings

This adjusts the brightness of the black (the gray level) for the sides of the screen. The standard is 0 (black). The level can be adjusted from 0 to 15. The factory setting is 3 (dark gray).

En-28

Setting the screen size for S1/S2 video input

If the S-video signal contains screen size information, the image will be automatically adjusted to fit the screen when this S1/S2 is set to AUTO. This feature is available only when an S-video signal is input via the VIDEO3 terminal.

Example: Setting “S1/S2” to “AUTO”

On “S1/S2” of “OPTION2” menu, select “AUTO”.

PREVIOUS PAGE PWR. MGT. CINEMA MODE LONG LIFE GRAY LEVEL S1/S2 PICTURE SIZE DVI SET UP PROTOCOL SET CLOSECAPTION CAPTION CONT NEXT PAGE

SEL. ADJ. RETURN

OPTION2 2 / 4

: OFF : ON

: 3 : AUTO : ON

: OFF : OFF : LOW

EXIT

Setting the signal and black level for DVI signal

Choose the signal for the DVI connector (PC or STB/ DVD) and set the black level.

Example: Setting the “PLUG/PLAY” mode to “STB/ DVD”

On “OPTION2” menu, select “DVI SET UP”, then press the MENU/ENTER button.

The “DVI SET UP” screen appears. On “PLUG/PLAY” of “DVI SET UP” menu, select “STB/

DVD”.

PLUG/PLAY BLACK LEVEL

SEL. ADJ. RETURN

DVI SET UP

: STB/DVD : HIGH

EXIT

Information

䡵 S1/S2 settings

AUTO: Adjusts the screen size automatically according to the S1/S2 video signal. OFF: Turns the S1/S2 function off.

Setting the picture size for RGB input signals

Use this procedure to switch the setting to “ON” or “OFF”. * This function is available only for 50 and 60 inch types.

Example: Setting the “PICTURE SIZE” mode to “OFF”

On “PICTURE SIZE” of “OPTION2” menu, select “OFF”.

PREVIOUS PAGE PWR. MGT. CINEMA MODE LONG LIFE GRAY LEVEL S1/S2 PICTURE SIZE DVI SET UP PROTOCOL SET CLOSECAPTION CAPTION CONT NEXT PAGE

SEL. ADJ. RETURN

OPTION2 2 / 4

: OFF : ON

: 3 : OFF : OFF

: OFF : OFF : LOW

EXIT

Information

䡵 PLUG/PLAY settings

PC: When connected to the PC signal. BLACK LEVEL is set to “LOW” automatically. STB/DVD:

When connected to the SET TOP BOX, DVD etc.

BLACK LEVEL is set to “HIGH” automatically.

䡵 BLACK LEVEL settings

LOW: When connected to the PC signal. HIGH:

When connected to the SET TOP BOX, DVD etc.

Change “HIGH” into “LOW” if the black level appears gray.

Setting the Protocol set

Use this setting when connecting a device which uses special protocol for RS-232C communication.

Example: Setting “ON”

On “PROTOCOL SET” of “OPTION2” menu, select “ON”.

PREVIOUS PAGE PWR. MGT. CINEMA MODE LONG LIFE GRAY LEVEL S1/S2 PICTURE SIZE DVI SET UP PROTOCOL SET CLOSECAPTION CAPTION CONT NEXT PAGE

SEL. ADJ. RETURN

OPTION2 2 / 4

: OFF : ON

: 3 : OFF : ON

: ON : OFF : LOW

EXIT

Information

䡵 PROTOCOL SET settings

ON: When special protocol is used. OFF: When NEC protocol is used (normal).

* Consult your dealer for details of protocol.

En-29

+ 173 hidden pages