Kenwood KMM-BT315, KMM-BT315U, KMM-BT515HD, KMR-M315BT Manual [es]

KMM-BT515HD KMM-BT315

KMM-BT315U KMR-M315BT

DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE

MODE D’EMPLOI

RECEPTOR DE MEDIOS DIGITALES

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model KMM-BT515HD/ KMM-BT315U/ KMM-BT315/ KMR-M315BT Serial number

US Residents Only

Register Online

Register your Kenwood product at www.Kenwoodusa.com

© 2015 JVC KENWOOD Corporation

B5A-0897-30 (KN)

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.

A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

i

IC (Industry Canada) Notice

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1)l’appareil ne doit pas produire de brouillage, et

(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.

Para cumplimiento de la COFETEL:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1)es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2)este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada”

	(For				/			/		)
	Contains Bluetooth Module						FCC ID:	ZWY8350X
							IC ID:	12033A-8350X
	(For			)
	Contains Bluetooth Module						FCC ID:	ZWY8811X
							IC ID:	12033A-8811X

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences

radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

ii

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2

License

1.The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2.The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3.The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4.The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1.When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2.The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 5 Indemnification of Licensor

1.Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2.The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

iii

Article 8	Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event:

(1)when the User violated any provision of this Agreement; or

(2)when a petition has been filed against the User for an attachment,

provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1.The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2.The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1.It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2.The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3.The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1.In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2.Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3.The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Copyright (c) 2009-2012 Petri Lehtinen <[e-mail]>

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

iv

CONTENTS

BEFORE USE	2
BASICS	3
GETTING STARTED	4

1Select the display language and cancel the demonstration

2 Set the clock and date

3 Set the initial settings

HD RadioTM tuner
(for									)						6
RADIO (for											/
				/								)			7
AUX															8
USB / iPod / ANDROID															9
Pandora® (for														/
					/								)		11
iHeartRadio® (for															/
					/								)		12
SiriusXM® Radio (for																/
					/								)		13
BLUETOOTH®															16
AUDIO SETTINGS															22
DISPLAY SETTINGS															24
TROUBLESHOOTING															25
REFERENCES															28
	Maintenance
	More information
SPECIFICATIONS															30
INSTALLATION /
CONNECTION															31

BEFORE USE

IMPORTANT

•To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

•Please keep the manual in a safe and accessible place for future reference.

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

•Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•Avoid using the external device if it might hinder safe driving.

•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•USB rating is indicated on the main unit. To view, detach the faceplate. ( 3)

•Depending on the types of cars, the antenna will automatically extend when you turn on the unit with

the antenna control wire connected ( 33, 34). Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•Do not leave the remote control in hot places such as on the dashboard.

•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

•Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

How to read this manual

•Operations are explained mainly using buttons on the faceplate of .

•English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. ( 5)

•[XX] indicates the selected items.

•( XX) indicates references are available on the stated page.

2

BASICS

Faceplate

Lights up when

Bluetooth connection is

Display window

established. ( 16)

Detach button	Volume knob	Flashes when the unit enters
		searching status.
Attach	Detach	How to reset
		Press the switch twice
		within 5 seconds after
		detaching the faceplate.

Remote control (RC-406)

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

: Remote control functions are not available.

How to replace the battery

To						On the faceplate		On the remote control
Turn on the power						Press	.	Press and hold SRC to turn off the power.
						• Press and hold to turn off the power. *1		( Pressing SRC does not turn on the power. )
Adjust the volume						Turn the volume knob.		Press	or	.
								Press ATT during playback to attenuate the sound.
								• Press again to cancel.
Select a source						Press	repeatedly.	Press SRC repeatedly.
Change the display information*2 Press DISP repeatedly. ( 29)								( Not available )
*1	For					: The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off).
*2	For			: You can also turn off the display information by pressing DISP repeatedly.

ENGLISH 3

GETTING STARTED

1Select the display language and cancel the demonstration

When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB”

1Turn the volume knob to select [ENG] (English) or [SPA] (Spanish), then press the knob.

[ENG] is selected for the initial setup.

(For / / )

Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”.

2Press the volume knob.

[YES] is selected for the initial setup.

3Press the volume knob again.

“DEMO OFF” appears.

2Set the clock and date

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [CLOCK], then press the knob.

To adjust the clock

3 Turn the volume knob to select [CLOCK ADJUST], then press the knob.

4Turn the volume knob to make the settings, then press the knob.

Hour Minute

5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob.

To set the date

7Turn the volume knob to select [DATE FORMAT], then press the knob.

8Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press the knob.

9 Turn the volume knob to select [DATE SET], then press the knob.

10Turn the volume knob to make the settings, then press the knob.

Day Month Year or Month Day Year

11Press and hold to exit.

To return to the previous setting item, press .

3Set the initial settings

1 Press repeatedly to enter STANDBY. 2 Press the volume knob to enter [FUNCTION].

3Turn the volume knob to select an item (see the following table), then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

		Default: XX
DISPLAY
	EASY MENU	ON: Both display and button illumination change to white color
		when entering [FUNCTION]. ; OFF: Both display and button
		illumination remain as [COLOR SELECT] color. ( 24)

4

GETTING STARTED

TUNER SETTING

	PRESET TYPE		NORMAL: Memorizes one station for each preset button in each band (FM1/
			FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel for each preset
			button, regardless of the selected band or SiriusXM channel.
SYSTEM
	KEY BEEP		ON: Activates the keypress tone. ; OFF: Deactivates.
	SOURCE SELECT
		PANDORA SRC	(For		/		/			)
			ON: Enables PANDORA in source selection. ; OFF: Disables. (						11)
		IHEART SRC	(For		/		/			)
			ON: Enables IHEARTRADIO in source selection. ; OFF: Disables. ( 12)

	BUILT-IN AUX		ON: Enables AUX in source selection. ; OFF: Disables. ( 8)
F/W UPDATE
	UPDATE SYSTEM / UPDATE HD (for				)
		F/W UP xx.xx	YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated).
			For details on how to update the firmware, see: www.kenwood.com/cs/ce/
FACTORY RESET			YES: Resets the settings to default (except the stored station). ; NO: Cancels.

REM SETTING* (for )

REMOTE ID SET Remote control ID list is displayed.

YES: Indicates that this ID is already registered. ; NO: Indicates that this ID is available.

Turn the volume knob to select an available ID (REM ID1/ ID2/ ID3), then press the knob to register.

REMOTE ID	ID1 DELETE/ ID2 DELETE/ ID3 DELETE: Selects the registered remote control ID
DEL	to delete.
	YES: Deletes the selected remote control ID. ; NO: Cancels.

CLOCK

	CLOCK DISPLAY	(For						/		/
						)
		ON: The clock time is shown on the display even when the
		unit is turned off. ; OFF: Cancels.
	DATE SET	(For					)
		DD/MM/YY: Sets the date for marine remote control display.
ENGLISH		Select the display language for [FUNCTION] menu and
		music information if applicable.
ESPANOL
		By default, [ENGLISH] is selected.

* Displayed only when KCA-RC55MR (optional accessory) is connected. (34)

ENGLISH 5

HD Radio™ tuner (for )

You can tune in to both conventional and HD Radio broadcasts.

•To find HD Radio stations in your area, visit <http://www.hdradio.com>.

Search for a station

1 Press

repeatedly to select HD RADIO.

2Press repeatedly (or press / on RC-406) to select FM1/ FM2/ FM3/ AM.

3Press S / T (or press S / on RC-406) to search for a station or channel.

•To change the searching method for S / T: Press repeatedly.

AUTO1 : Automatically search for a station or channel. AUTO2 : Search for a preset station or channel. MANUAL : Manually search for a station or channel.

•To store a station or channel: Press and hold one of the number buttons (1 to 6).

•To select a stored station or channel: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).

Direct Access Tuning (using RC-406)

1 Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a frequency.

3 Press to search for a station or channel.

•To cancel, press or DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

Select an HD Radio multicast channel

Many HD Radio stations offer more than one channel programming.

This service is called multicasting. While receiving HD Radio multicast channels....

Press S / T to select your desired channel (HD1 to HD8).

“LINKING” appears while linking to a multicast channel.

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

		Default: XX
TUNER SETTING
	IF BAND	AUTO: Increases the tuner selectivity to reduce interference noises from adjacent
		FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises
		from adjacent FM stations, but sound quality will not be degraded and the stereo
		effect will remain.
	AUTO MEMORY	YES: Automatically starts memorizing 6 stations with good reception. ;
		NO: Cancels.
		• Selectable only if [NORMAL] is selected for [PRESET TYPE]. ( 5)
	RECEIVE MODE	Sets the receive mode of the HD Radio receiver.
		AUTO: Automatically tunes to analog broadcast when there is no digital
		broadcast. ; DIGITAL: Tunes in to digital broadcast only. ; ANALOG: Tunes in to
		analog broadcast only.
CLOCK
	TIME SYNC	ON: Synchronizes the unit’s time to the Radio Broadcast Data System station
		time. ; OFF: Cancels.

6

RADIO (for / / )

Search for a station

1 Press

repeatedly to select TUNER.

2Press repeatedly (or press / on RC-406) to select FM1/ FM2/ FM3/ AM.

3Press S / T (or press S / on RC-406) to search for a station.

•To change the searching method for S / T: Press repeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

•To store a station: Press and hold one of the number buttons (1 to 6).

•To select a stored station: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).

Direct Access Tuning (using RC-406) (except for )

1 Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a frequency.

3 Press to search for a station.

•To cancel, press or DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

				Default: XX
TUNER SETTING
	AUTO	YES: Automatically starts memorizing 6 stations with good reception. ;
	MEMORY	NO: Cancels.
		• Selectable only if [NORMAL] is selected for [PRESET TYPE]. ( 5)
	MONO SET	ON: Improves the FM reception, but the stereo effect may be lost. ;
		OFF: Cancels.
	NEWS SET	(For		)
		ON: The unit will temporarily switch to News Programme if available. ;
		OFF: Cancels.
	REGIONAL	(For		)
		ON: Switches to another station only in the specific region using the “AF”
		control. ; OFF: Cancels.
	AF SET	(For		)
		ON: Automatically searches for another station broadcasting the same
		program in the same Radio Data System network with better reception
		when the current reception is poor. ; OFF: Cancels.
	TI	ON: Allows the unit to temporarily switch to Traffic Information if available
		(“TI” lights up). ; OFF: Cancels.
	PTY SEARCH	Select the available Program Type ( 8), then, press S / T to start.

ENGLISH 7

RADIO (for / / )

CLOCK

TIME SYNC	ON: Synchronizes the unit’s time to the Radio Broadcast Data System/
	Radio Data System station time. ; OFF: Cancels.

AUX

Preparation:

Select [ON] for [BUILT-IN AUX]. ( 5)

Start listening

1 Connect a portable audio player (commercially available).

Available Program Type for PTY SEARCH

Auxiliary input jack

(For

/

)

Portable audio player

SPEECH :

NEWS, INFORM (information), SPORTS, TALK, LANGUAGE, REL TALK

(religious talk), PERSNLTY (personality), PUBLIC, COLLEGE, HABL ESP

(spanish talk), WEATHER

MUSIC :

ROCK, CLS ROCK (classic rock), ADLT HIT (adult hits), SOFT RCK

(softrock), TOP 40, COUNTRY, OLDIES, SOFT, NOSTALGA (nostalgia),

3.5 mm (1/8") stereo mini plug with “L”

JAZZ, CLASSICL (classical), R & B (rhythm and blues), SOFT R&B

(soft rhythm and blues), REL MUSC (religious music), MUSC ESP

2

shaped connector (commercially available)

(spanish music), HIP HOP

Press

repeatedly to select AUX.

(For

)

3

Turn on the portable audio player and start playback.

SPEECH :

NEWS, AFFAIRS, INFO (information), SPORT, EDUCATE, DRAMA,

CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL,

Set the AUX name

RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

While listening to a portable audio player connected to the unit...

MUSIC : POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),

CLASSICS, OTHER M (music), JAZZ, COUNTRY, NATION M (music),

1

Press the volume knob to enter [FUNCTION].

OLDIES, FOLK M (music)

2

Turn the volume knob to select [SYSTEM], then press the knob.

The unit will search for the Program Type categorized under [SPEECH] or

3

Turn the volume knob to select [AUX NAME SET], then press the knob.

4

Turn the volume knob to select an item, then press the knob.

[MUSIC] if selected.

AUX (default)/ DVD/ PORTABLE/ GAME/ VIDEO/ TV

5

• [MONO SET]/ [NEWS SET]/ [REGIONAL]/ [AF SET]/ [TI]/ [PTY SEARCH] is selectable

Press and hold

to exit.

To return to the previous setting item, press

.

only when the band is FM1/ FM2/ FM3.

•If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

8

USB / iPod / ANDROID

Start playback

The source changes automatically and playback starts.

USB input terminal

USB

CA-U1EX (max.: 500 mA) (optional accessory)

iPod/iPhone

KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2

ANDROID*3

Micro USB 2.0 cable*2 (commercially available)

*1
	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.

To		On the faceplate				On the remote control
Playback / pause		Press	.			Press	.
Reverse / Fast-forward*4		Press and hold S / T.				Press and hold S /		.
Select a track/file		Press S / T.				Press S /	.
Select a folder*5		Press J / K.				Press	/	.
Repeat play*6		Press	repeatedly.
		FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT : MP3/WMA/AAC/WAV/FLAC file
		FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF : iPod or ANDROID
Random play*6		Press	repeatedly.
		FOLDER RANDOM/ RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file, iPod or
					ANDROID
		Press and hold		to select ALL RANDOM.*7
*3	When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions
	to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device
*4	before connecting. ( 28)
	For ANDROID: Applicable only when [BROWSE MODE] is selected. (				10)
*5	Only for MP3/WMA/AAC/WAV/FLAC files. This does not work for iPod/ ANDROID.
*6	For iPod/ ANDROID: Applicable only when [MODE OFF]/ [BROWSE MODE] is selected. ( 10)
*7	Only for MP3/WMA/AAC/WAV/FLAC files.

ENGLISH 9

USB / iPod / ANDROID

Select control mode

While in IPOD source, press 5 repeatedly.

MODE ON : Control iPod using the iPod itself. However, you can still play/pause, file skip, fast-forward or reverse from this unit.

MODE OFF : Control iPod from this unit.

While in ANDROID source, press 5 repeatedly.

BROWSE MODE : Control Android device from this unit via KENWOOD MUSIC PLAY application installed in the Android device.

HAND MODE : Control Android device using the Android device itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Select music drive

Press 5 repeatedly.

Stored songs in the following drive will be played back.

•Selected internal or external memory of a smartphone (Mass Storage Class).

•Selected drive of a multiple drives device.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

1	Press	.
2	Turn the volume knob to select a folder/list, then press the knob.
3	Turn the volume knob to select a file, then press the knob.
	Quick Search
	If you have many files, you can search through them quickly.
	Turn the volume knob quickly to browse through the list quickly.

–Not applicable for iPod.

(or)

Press S / T to search at a preset skip search ratio. (11, [SKIP SEARCH])

• Pressing and holding S / T searches at a 10% ratio.

–Not applicable for MP3/ WMA/ AAC/ WAV/ FLAC files.

(or)

Alphabet search (applicable only for iPod)

If you have many files in the iPod, you can search through them quickly according to the first character of the file name.

Turn the volume knob quickly to enter character search.

Turn the volume knob to select the character.

To search for a character other than A to Z and 0 to 9, enter only “*”. Press S / T to move to the entry position.

• You can enter up to 3 characters.

Press the volume knob to start searching.

•To return to the root folder/ first file/ top menu, press 5. (Not applicable for BT AUDIO source.)

•To return to the previous setting item, press .

•To cancel, press and hold .

•For iPod, applicable only when [MODE OFF] is selected.

•For ANDROID, applicable only when [BROWSE MODE] is selected.

10

USB / iPod / ANDROID

Pandora® (for

/

/

)

Preparation:

Direct Music Search (using RC-406)

Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then

(except for

)

create an account and log in to Pandora.

1

Press DIRECT.

• Select [ON] for [PANDORA SRC]. (

5)

2 Press the number buttons to enter a track/file

3

number.

Start listening

Press

to search for music.

1 Open the Pandora application on your device.

•

To cancel, press

or DIRECT.

2

Connect your device to the USB input terminal.

• Not available if Random Play is selected.

USB input terminal

• Not applicable for iPod and ANDROID.

Other settings

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select an item (see

KCA-iP102 / KCA-iP103 (optional accessory)*1

or accessory cable of the iPod/iPhone*2

the following table), then press the knob.

3 Repeat step 2 until the desired item is selected

3

Press

repeatedly to select PANDORA.

4

or activated.

Broadcast starts automatically.

Press and hold

to exit.

To

On the faceplate

On the remote control

To return to the previous setting item, press

.

Playback / pause

Press

.

Press

.

Default: XX

Skip a track

Press T.

Press

.

USB

Thumbs up or thumbs down*3

Press J / K.

Press

/

.

MUSIC DRIVE DRIVE CHANGE: The next drive ([DRIVE 1]

*1

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

to [DRIVE 4]) is selected automatically and

*2

Do not leave the cable inside the car when not using.

playback starts.

*3

If thumbs down is selected, the current track is skipped.

Repeat steps 1 to 3 to select the following

drives.

Create and save a new station

SKIP SEARCH 0.5%/ 1%/ 5%/ 10%: While listening to iPod or ANDROID, selects the skip search ratio over the total files.

1	Press	.
2	Turn the volume knob to select [NEW STATION], then press the knob.

3Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.

A new station is created based on the current song or artist.

4 Press and hold one of the number buttons (1 to 5) to store.

To select a stored station, press one of the number buttons (1 to 5).

ENGLISH 11

Pandora® (for / / )

Search for a registered station

1 Press

.

2Turn the volume knob to select an item, then press the knob.

[SORT BY DATE]: According to the registered date [SORT BY A-Z]: Alphabetical order

3Turn the volume knob to select the desired station, then press the knob.

To cancel, press and hold .

(or using RC-406) (except )

Press J/ K to search for a station, then press .

iHeartRadio® (for / / )

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.

• Select [ON] for [IHEART SRC]. ( 5)

Start listening

1 Open the iHeartAuto application on your device.

2Connect your device to the USB input terminal.

USB input terminal

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.

Delete a station

While listening to PANDORA...

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [SYSTEM], then press the knob.

3Turn the volume knob to select [STATION DEL], then press the knob.

4Turn the volume knob to select [SORT BY A-Z] or [SORT BY DATE], then press the knob.

5Turn the volume knob to select the desired station to delete, then press the knob.

6 Turn the volume knob to select [YES], then press the knob. 7 Press and hold to exit.

To return to the previous setting item, press .

KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2

3Press repeatedly to select IHEARTRADIO.

Broadcast starts automatically.

*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.
To		On the faceplate			On the remote control
Playback / pause		Press	.		Press	.
Skip a track for custom		Press T.			Press	.
station
Thumbs up or thumbs down		Press J / K.			( Not available )
Create a new/custom station		Press 1.			( Not available )
Scan for live station		1 Press 2 to start
		scanning.
		2 Press	to		( Not available )
		listen to the
		station.

12

iHeartRadio® (for / / )

Search and store a station

1 Press

.

2Turn the volume knob to select a category, then press the knob.

3Turn the volume knob to select the desired station, then press the knob.

When a city list appears, you can search cities in alphabetical order by turning the volume knob quickly.

To cancel, press and hold .

(or using RC-406) (except )

Press J/ K to search for a station, then press .

•To store a station: Press and hold one of the number buttons (3 to 5).

•To select a stored station: Press one of the number buttons (3 to 5).

SiriusXM® Radio (for / / )

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com.

Preparation:

1 Connect the optional SiriusXM Vehicle Tuner (commercially available).

Antenna

Expansion port on	SiriusXM Vehicle Tuner
the rear panel

2Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its packaging.

The Radio ID does not include the letters I, O, S or F.

3Activate the subscription.

For users in the U.S.A.:

Online: Go to www.siriusxm.com Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to www.siriusxm.ca/activatexm Phone: Call 1-877-438-9677

4 Press repeatedly to select SIRIUS XM to start updating.

Start listening

1 Press repeatedly to select SIRIUS XM.

2 Press repeatedly to select a band.

3 Press .

“” lights up.

4Turn the volume knob to select a category, then press the knob.

If “ALL CHANNELS” is selected, all the available channels will be shown.

ENGLISH 13

SiriusXM® Radio (for / / )

5Turn the volume knob to select a channel, then press the knob.

(or)

Press S / T to search for a channel manually.

•Pressing and holding S / T changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 15)

To change the tuning method for S / T: Press .

Each time you press , the tuning method switches between “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).

Direct Access Tuning (using RC-406)

(except )

1 Press DIRECT to enter Direct Access Tuning.

2Press the number buttons to enter a channel number.

3 Press to start searching.

•To cancel, press or DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

SiriusXM Keymode

Press and hold to change the keymode (channel or replay).

(Default: Channel keymode)

“” lights up when replay keymode is selected.

When channel keymode is selected...

To	On the faceplate			On the remote control
Select a channel	Press S / T.			Press S /	.
Change a channel	Press and hold S / T.			Press and hold S /		.
rapidly
Store a channel of the	Press and hold one of the			(Not available)
current band	number buttons (1 to 6).
Select a stored channel	Press one of the number buttons (1 to 6).
of the current band
When replay keymode is selected...
To	On the faceplate			On the remote control
Playback / pause	Press	.		Press	.
Select a track	Press S / T.			Press S /	.
Rewind / Fast-forward	Press and hold S / T.			Press and hold S /		.
Go to Live	Press 1.

SmartFavorites and TuneStart™

User stored channels are recognized as SmartFavorite channels*. The SiriusXM Vehicle Tuner automatically buffers the broadcast content in the background.

• SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle Tuner.

*SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites. The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as SmartFavoites.

When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.

•Playback starts from the beginning of the song if [TUNE START] is set to [ON] ( 15) for most music channels stored as a SmartFavorite.

Press one of the number buttons (1 to 6) to select a stored channel.

14

SiriusXM® Radio (for / / )

TuneScan™

You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel.

Press and hold to start scanning the first 6 seconds of the recorded music contents.

•To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.

•To select the previous/next song, press S / T.

•To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.

SiriusXM settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select [SIRIUS XM], then press the knob.

3Turn the volume knob to select an item (see the following table), then press the knob.

4Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item.

5 Press and hold

to exit.

To return to the previous setting item, press .

Default: XX

CHANNEL LOCK			To unlock settings:
			1	Turn the volume knob to select a number.
			2	Press S / T to move to the entry position.
			3	Repeat steps 1 and 2 to enter the current pass code.
			4	(Initial pass code is 0000.)
				Press the volume knob to confirm.
	CODE SET		1 Turn the volume knob to select a number.
			2	Press S / T to move to the entry position.
			3	Repeat steps 1 and 2 to enter a new 4-digit pass code.
			4	Press the volume knob to confirm.
			5	Repeat steps 1 to 4 to reconfirm the pass code.
			• Make a note of the new pass code to enter channel lock settings for next time.
	LOCK SETTING		MATURE CH: Selects the SiriusXM-defined lock setting. ; USER DEFINED: Selects
			the individual channels the user wants to lock. ; OFF: Cancels.
	CHANNEL EDIT*1		1 Turn the volume knob to select a category, then press the knob.
			2	Turn the volume knob to select a channel you want to lock, then press the
				knob.
			3	“L” appears in front of the channel number.
				Press and hold	to exit.
	CHANNEL CLEAR*1		YES: Clears all the locked channels. ; NO: Cancels.
	TUNE START*2		ON: All qualified music channels in the SmartFavorite will start playback from the
			beginning of the song. ; OFF: Cancels.
	SIGNAL LEVEL		NO SIGNAL/ WEAK/ GOOD/ STRONG: Shows the strength of the current received
			signal.
	BUFFER USAGE		0% — 100% (0): Shows the memory usage for Replay buffer.
	SXM RESET		YES: Resets stored channel and lock setting to default. ; NO: Cancels.
*1		Displayed only when [USER DEFINED] is selected.
*2		Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports SmartFavorites.

ENGLISH 15

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

–Hands-Free Profile (HFP)

–Advanced Audio Distribution Profile (A2DP)

–Audio/Video Remote Control Profile (AVRCP)

–Serial Port Profile (SPP)

–Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

–Sub Band Codec (SBC)

–Advanced Audio Coding (AAC)

–aptX Codec (aptX) (for /

/ )

Connect the microphone

Rear panel

Microphone (supplied)

Microphone input jack*

Adjust the

microphone angle

Secure using cord clamps (not supplied) if necessary.

*For , connect to the microphone input terminal. ( 33)

Pair and connect a Bluetooth device for the first time

1 Press

to turn on the unit.

2Search and select this unit model name (KMM-BT51*HD/ KMM-BT31*U/ KMM-BT31*/ KMR-M31*BT) on the Bluetooth device.

“PAIRING” “PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” scrolls on the display.

•For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.

3Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

•This unit supports Secure Simple Pairing (SSP).

•Up to 10 devices can be registered (paired) in total.

•Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, 20, [DEVICE DELETE].

Once pairing is completed, Bluetooth connection is established automatically.

•“BT1” and/or “BT2” indicator on the faceplate lights up.

•A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

•Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

•Refer to the instruction manual of the Bluetooth device for more information.

Auto Pairing

When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if:

–Bluetooth function of the connected device is turned on.

–[AUTO PAIRING] is set to [ON]. ( 20)

–KENWOOD MUSIC PLAY application is installed on the Android device ( 9) and [BROWSE MODE] is selected ( 10).

16

BLUETOOTH®

Connect with a remote device by One-touch (NFC) (for )

Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices.

By holding an NFC-compatible remote device near to the N-Mark on the unit (volume knob), the unit and remote device proceed to complete pairing and established the BLUETOOTH connection automatically.

1Activate the NFC function on the remote device.

Refer to the instruction manual of the remote device for more information.

2Hold the remote device near to the N-Mark on the unit (volume knob).

The device vibrates when pairing is completed.

•To disconnect, hold the remote device near to the N-Mark on the unit (volume knob) again.

•This unit only can recognize and connect to one NFCcompatible device at a time.

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

•ZONE 2 illuminates in green color and flashes.

•The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 18)

During a call:

•The display illuminates according to the settings made for [DISPLAY] ( 24) and ZONE 2 illuminates in green color.

•If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

	To	On the faceplate		On the remote control
First incoming call...
	Answer a call	Press	or the volume knob	Press .
		or one of the number buttons
		(1 to 6).
	Reject a call	Press	.	Press	.
	End a call	Press	.	Press	.

ENGLISH 17

BLUETOOTH®

	To	On the faceplate		On the remote control
While talking on the first incoming call...
	Answer another incoming	Press .		Press .
	call and hold the current
	call
	Reject another incoming	Press	.	Press	.
	call
While having two active calls...
	End current call and	Press	.	Press	.
	activate held call
	Swap between the	Press .		Press .
	current call and held call
Adjust the phone volume		Turn the volume knob during
[00] to [35] (Default: [15])		a call.		( Not available )
		• This adjustment will not
		affect the volume of the other
		sources.
Switch between hands-free		Press	during a call.
and private talk modes		• Operations may vary		( Not available )
		according to the connected
		Bluetooth device.

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

		Default: XX
MIC GAIN		–10 — +10 (–4): The sensitivity of the microphone
		increases as the number increased.
NR LEVEL		–5 — +5 (0): Adjust the noise reduction level
		until the least noise is being heard during a phone
		conversation.
ECHO CANCEL		–5 — +5 (0): Adjust the echo cancellation delay
		time until the least echo is being heard during a
		phone conversation.
	Make the settings for receiving a call
1 Press		to enter Bluetooth mode.

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

		Default: XX
SETTINGS
	AUTO ANSWER	1 — 30: The unit answers incoming call
		automatically in the selected time (in seconds). ;
		OFF: Cancels.
	BATT/SIGNAL*	AUTO: Shows the strength of the battery and signal
		when the unit detects a Bluetooth device and the
		Bluetooth device is connected. ; OFF: Cancels. Clock
		time is shown.

* Functionality depends on the type of the phone used.

18

BLUETOOTH®

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press

to enter Bluetooth mode.

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.

4 Press and hold

to exit.

To return to the previous setting item, press .

CALL HISTORY (Applicable only if the phone supports PBAP)

1Press the volume knob to select a name or a phone number.

•“INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.

•Press DISP to change the display category (NUMBER or NAME).

•“NO DATA” appears if there is no recorded call history.

2 Press the volume knob to call.

PHONE BOOK (Applicable only if the phone supports PBAP)

1Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts).

The first menu (ABCDEFGHIJK) appears.

•To go to the other menu (LMNOPQRSTUV or WXYZ1*), press J/ K.

•To select the desired first letter, turn the volume knob or press S / T, then press the knob.

Select “1” to search with numbers and select “*” to search with symbols. 2 Turn the volume knob to select a name, then press the knob.

3 Turn the volume knob to select a phone number, then press the knob to call.

•The phonebook of the connected phone is automatically transferred to the unit when pairing.

•Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL

•This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)

NUMBER DIAL	1 Turn the volume knob to select a number (0 to 9) or
	character ( , #, +).

2Press S / T to move the entry position.

Repeat steps 1 and 2 until you finish entering the phone number.

3 Press the volume knob to call.

(or using RC-406) (except

)

1Press the number buttons (0 to 9) to enter the phone number.

	2 Press	to call.
VOICE	Speak the name of the contact you want to call or the voice
	command to control the phone functions.
	( Make a call using voice recognition)

BATT LOW/ MID/ FULL*: Shows the strength of the battery.

NO SIGNAL/ LOW/ MID/ MAX*: Shows the strength of the current received signal.

* Functionality depends on the type of the phone used.

Make a call using voice recognition

1Press and hold to activate the voice recognition of the connected phone.

2Speak the name of the contact you want to call or the voice command to control the phone functions.

•Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

•This unit also supports the intelligent personal assistant function of iPhone.

ENGLISH 19

BLUETOOTH®

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press

to enter Bluetooth mode.

2Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob.

3Turn the volume knob to select a contact or enter a phone number.

If a contact is selected, press the volume knob to show the phone number.

4Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored.

To erase a contact from the preset memory, select [NUMBER DIAL] in step 2 and store a blank number.

Make a call from memory

1 Press to enter Bluetooth mode.

2 Press one of the number buttons (1 to 6).

3Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.

4 Press and hold

to exit.

To return to the previous setting item, press .

			Default: XX
BT MODE
	PHONE SELECT	Selects the phone or audio device to connect or disconnect.
		“*” appears in front of the device name when connected.
	AUDIO SELECT
		•	You can only connect a maximum of two Bluetooth phones and one
			Bluetooth audio device at any time.
	DEVICE DELETE	1	Turn the volume knob to select a device to delete, then press the
		2	knob.
			Turn the volume knob to select [YES] or [NO], then press the knob.
	PIN CODE EDIT	Changes the PIN code (up to 6 digits).
	(0000)	1	Turn the volume knob to select a number.
		2	Press S / T to move the entry position.
		3	Repeat steps 1 and 2 until you finish entering the PIN code.
			Press the volume knob to confirm.
	RECONNECT	ON: The unit automatically reconnect when the last connected
		Bluetooth device is within range. ; OFF: Cancels.
	AUTO PAIRING	ON: The unit automatically pair supported Bluetooth device (iPhone/
		iPod touch/ Android device) when it is connected through USB input
		terminal. Depending on the operating system of the connected device,
		this function may not work. ; OFF: Cancels.
	INITIALIZE	YES: Initializes all the Bluetooth settings (including stored pairing,
		phonebook, and etc.). ; NO: Cancels.

20

BLUETOOTH®

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name (KMM-BT51*HD/ KMM-BT31*U/ KMM-BT31*/ KMR-M31*BT) on the Bluetooth device.

3 Operate the Bluetooth device to confirm pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after

the test.
PAIRING:	Pairing status
HF CNT:	Hands-Free Profile (HFP) compatibility
AUD CNT: Advanced Audio Distribution Profile
	(A2DP) compatibility
PB DL:	Phonebook Access profile (PBAP)
	compatibility

To cancel test mode, press and hold to turn off the unit.

BLUETOOTH — Audio

Audio player via Bluetooth

1 Press	repeatedly to select BT AUDIO (or press SRC on RC-406).
2 Operate the Bluetooth audio player to start playback.
To		On the faceplate			On the remote control
Playback / pause		Press	.		Press	.
Select group or folder		Press J/ K.			Press	/	.
Reverse / Forward skip		Press S / T.			Press S /	.
Reverse / Fast-forward		Press and hold S / T.			Press and hold S /		.
Repeat play		Press	repeatedly.		( Not available )
		ALL REPEAT, FILE REPEAT, REPEAT OFF
Random play		Press and hold		to select
		ALL RANDOM.			( Not available )
		• Press	to select RANDOM OFF.
Select a file from a		Refer to “Select a file from a			( Not available )
folder/list		folder/list” on page 10.

Operations and display indications may differ according to their availability on the connected device.

ENGLISH 21

BLUETOOTH®

Internet radio via Bluetooth

(for / / )

Listen to Pandora

You can listen to Pandora on the Android device via Bluetooth on this unit.

Preparation:

Select [ON] for [PANDORA SRC]. ( 5)

1 Open the Pandora application on your device.

2Connect your Bluetooth audio player via Bluetooth connection. ( 16)

3Press repeatedly to select PANDORA.

The source switches and broadcast starts automatically.

You can operate Pandora in the same way as Pandora for iPod/iPhone. ( 11)

Listen to iHeartRadio

You can listen to iHeartRadio on the Android device via Bluetooth on this unit.

Preparation:

Select [ON] for [IHEART SRC]. ( 5)

1Open the iHeartAuto application on your smart phone.

2Connect your smart phone via Bluetooth connection. ( 16)

3Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts automatically.

You can operate iHeartRadio in the same way as iHeartRadio for iPod/iPhone. ( 12)

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [AUDIO CONTROL], then press the knob.

3 Turn the volume knob to select an item (see the following table), then press the knob. 4 Repeat step 3 until the desired item is selected or activated.

5 Press and hold to exit.

(or using RC-406) (except )

1 Press AUD to enter [AUDIO CONTROL].

2 Press J/ K to select an item, then press .

To return to the previous setting item, press .

Default: XX

SUB-W LEVEL		–50 to +10 (0): Adjusts the subwoofer output level.
MANUAL EQ
	BAND1 LEVEL	LEVEL	–9 to +9 (0): (Refer to BAND2 LEVEL below.)
		BASS EXTEND	ON: Turns on the extended bass. ; OFF: Cancels.
	BAND2 LEVEL to	–9 to +9 (0): The sound elements (frequency level, tone level, Q factor) are preset into each
	BAND13 LEVEL	selection (BAND1 LEVEL to BAND13 LEVEL).
		Adjusts the level to memorize for each source. (Before making an adjustment, select the source you
		want to adjust.)
	Q FACTOR	1.35/ 1.50/ 2.00: Adjust the quality factor.
PRESET EQ		NATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL/ USER: Selects a preset equalizer
		suitable to the music genre. (Select [USER] to use the settings made in [MANUAL EQ].)
BASS BOOST		LEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5: Selects your preferred bass boost level. ;
		OFF: Cancels.
LOUDNESS		LEVEL1/ LEVEL2: Selects your preferred low and high frequencies boost to produce a well-
		balanced sound at a low volume level. ; OFF: Cancels.
SUBWOOFER SET		ON: Turns on the subwoofer output. ; OFF: Cancels.
FADER		R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE		L15 to R15 (0): Adjusts the left and right speaker output balance.

22

AUDIO SETTINGS

VOLUME OFFSET	–15 to +6 (0): Preset the initial volume level of each source.
	(Before adjustment, select the source you want to adjust.)

SOUND EFFECT

	SOUND RECNSTR (Not applicable for HD RADIO/TUNER source, AUX source and
	(Sound	SIRIUS XM source.)
	reconstruction)	ON: Creates realistic sound by compensating the high-
		frequency components and restoring the rise-time of
		the waveform that are lost in audio data compression. ;
		OFF: Cancels.
	SPACE ENHANCE (Not applicable for HD RADIO/TUNER source.)
		SMALL/ MEDIUM/ LARGE: Virtually enhances the sound
		space. ; OFF: Cancels.
	SND REALIZER	LEVEL1/ LEVEL2/ LEVEL3: Virtually makes the sound more
		realistic. ; OFF: Cancels.
	STAGE EQ	LOW/ MIDDLE/ HIGH: Virtually adjust the sound position
		heard from the speakers. ; OFF: Cancels.
	DRIVE EQ	ON: Boosts the frequency to reduce the noise heard from
		outside the car or running noise of the tyres. ; OFF: Cancels.
SPEAKER SIZE
	FRONT	SIZE	3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/
			5×7/ 6×8/ 6×9/ 7×10: Selects according to the
			connected speaker size for optimum performance.
		TWEETER	SMALL/ MIDDLE/ LARGE: Selects according
			to the size range of the connected tweeter for
			optimum performance. ; NONE: Not connected.
	REAR	3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ 6×8/
		6×9/ 7×10: Selects according to the connected speaker size
		for optimum performance. ; NONE: Not connected.
	SUBWOOFER	6.5"/ 8"/ 10"/ 12"/ 15" OVER: Selects according to the
		connected speaker size for optimum performance. ;
		NONE: Not connected.

X ' OVER

	TWEETER	FRQ	1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ/ 10KHZ/
			12.5KHZ: Adjusts the crossover frequency for the tweeter speaker.
		GAIN LEFT	–8 to 0: Adjusts the output volume of the left tweeter.
		GAIN RIGHT	–8 to 0: Adjusts the output volume of the right tweeter.
	FRONT HPF	F - HPF FRQ	30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/
			150HZ/ 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency
			for the selected speakers (high pass filter). ; THROUGH: All signals
			are sent to the selected speakers.
		F - HPF SLOPE	–6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope.
			(Selectable only if a setting other than [THROUGH] is selected for
			[F - HPF FRQ].)
		F - HPF GAIN	–8 to 0: Adjusts the output volume of the selected speaker.
	REAR HPF	R - HPF FRQ
		R - HPF SLOPE	(Refer FRONT HPF settings above.)
		R - HPF GAIN
	SUBWOOFER	SW LPF FRQ	30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/
	LPF		150HZ/ 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency
			for the subwoofer (low pass filter). ; THROUGH: All signals are sent
			to the subwoofer.
		SW LPF SLOPE	–6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope.
			(Selectable only if a setting other than [THROUGH] is selected for [SW
			LPF FRQ].)
		SW LPF PHASE	REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
			output to be in line with the speaker output for optimum performance.
		SW LPF GAIN	–8 to 0: Adjusts the output volume of the subwoofer.

•[SUB-W LEVEL]/ [SUBWOOFER] of [SPEAKER SIZE]/ [SUBWOOFER LPF] of [X ‘ OVER] is selectable only if [SUBWOOFER SET] is set to [ON].

•[TWEETER], [REAR HPF] and [SUBWOOFER LPF] of [X ‘ OVER] is selectable only if a setting other than [NONE] is selected for [TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE].

•Once you have selected the speaker size ([SPEAKER SIZE]), the frequency and slope settings are automatically set for the crossover of the selected speaker.

ENGLISH 23

DISPLAY SETTINGS

Set the dimmer

Press and hold DISP (DIMMER) to turn on or off the dimmer.

•If you have set [DIMMER TIME], it will be canceled once you press and hold this button.

Other settings

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [DISPLAY], then press the knob.

3Turn the volume knob to select an item (see the following table), then press the knob.

4Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item.

5 Press and hold

to exit.

To return to the previous setting item, press .

								Default: XX
COLOR SELECT	Select color for ALL ZONE, ZONE 1 and ZONE 2 separately.
	1	Select a zone.
	2	Select a color for the selected zone.
		VARIABLE SCAN/ CUSTOM R/G/B/ preset colors*
		Default:			/		/		:
		VARIABLE SCAN		: CUSTOM R/G/B (R = 9/ G = 9/ B = 9)
	To make your own color, select [CUSTOM R/G/B]. The color you have
	made will be stored in [CUSTOM R/G/B].
	1	Press the volume knob to enter the detailed color adjustment.
	2	Press S/ Tto select the color (R/ G/ B) to adjust.
	3	Turn the volume knob to adjust the level (0 — 9), then press the knob.
DIMMER	Dim the display illumination and button illumination.
	ON: Dimmer is turned on. ; OFF: Cancels.
	DIMMER TIME: Set the dimmer on and off time.
	1	Turn the volume knob to adjust the [ON] time, then press the knob.
	2	Turn the volume knob to adjust the [OFF] time, then press the knob.
	(Default: [ON]: 6:00 PM; [OFF]: 6:00 AM)
BRIGHTNESS	1 Select a zone.

20 — 31: Select your preferred brightness level for display illumination and button illumination.

TEXT SCROLL	AUTO/ ONCE: Select whether to scroll the display information
	automatically, or scroll only once. ; OFF: Cancels.

*Preset colors: RED1/ RED2/ RED3/ PURPLE1/ PURPLE2/ PURPLE3/ PURPLE4/ BLUE1/ BLUE2/ BLUE3/ SKYBLUE1/ SKYBLUE2/ LIGHTBLUE/ AQUA1/ AQUA2/ GREEN1/ GREEN2/ GREEN3/ YELLOWGREEN1/ YELLOWGREEN2/ YELLOW/ ORANGE1/ ORANGE2/

ORANGERED

24

TROUBLESHOOTING

Symptom					Remedy
	Sound cannot be heard.				• Adjust the volume to the optimum level.
					• Check the cords and connections.
	“MISWIRING CHECK WIRING				Turn the power off, then check to be sure the
	THEN PWR ON” appears.				terminals of the speaker wires are insulated
					properly. Turn the power on again.
	“PROTECTING SEND SERVICE”				Send the unit to the nearest service center.
General	appears.
	•	The unit does not turn on.			Clean the connectors. ( 28)
	•	Sound cannot be heard.
	• Information shown on the
		display is incorrect.
	The unit does not work at all.				Reset the unit. ( 3)
	(For			)	Setting/deleting the remote control ID is
	“SET ERROR” / “DEL ERROR”				unsuccessful. Turn the power off, then turn on
					the power and perform the operation again.
					( 5)
Radio/HD Radio	•	to the radio.			Connect the antenna firmly.
		Radio reception is poor.
	• Static noise while listening
	“READING” keeps flashing.				Do not use too many hierarchical levels or folders.
iPod	Elapsed playing time is not				This is caused by how the files are recorded.
	correct.
USB /
	“LOADING” appears when you				This unit is still preparing the iPod/iPhone music
	enter search mode by pressing				list. It may take some time to load, try again later.
		.

	Symptom		Remedy
		Correct characters are not	• This unit can only display uppercase letters, numbers,
		displayed (e.g. album		and a limited number of symbols.
		name).	• Depending on the display language you have selected
				( 5), some characters may not be displayed
				correctly.
		“NA FILE”	Make sure the media contains supported audio files.
			(	28)
	iPod/	“READ ERROR”	Copy the files and folders onto the USB device again. If
			use another USB device.
			this does not solve the problem, reset the USB device or
	USB
		“NO DEVICE”	Connect a USB device, and change the source to USB
			again.
		“COPY PRO”	A copy-protected file is played.
		“NA DEVICE”	Connect a supported USB device, and check the
			connections.
		“NO MUSIC”	Connect a USB device that contains playable audio files.
		“iPod ERROR”	•	Reconnect the iPod.
			•	Reset the iPod.
		• Sound cannot be heard	• Reconnect the Android device.
		during playback.	• If in [HAND MODE], launch any media player
		• Sound output only from		application on the Android device and start playback.
	ANDROID	the Android device.	• If in [HAND MODE], relaunch the current media
				player application or use another media player
				application.
			• Restart the Android device.
			• If this does not solve the problem, the connected
				Android device is unable to route the audio signal to
				unit. ( 28)

ENGLISH 25

TROUBLESHOOTING

Symptom		Remedy
	Cannot playback at	• Make sure KENWOOD MUSIC PLAY APP is installed on the
	[BROWSE MODE].	Android device. ( 9)
		• Reconnect the Android device and select the appropriate
		control mode.
		• If this does not solve the problem, the connected Android
		device does not support [BROWSE MODE]. (	28)
ANDROID
	“NO DEVICE” or	• Switch off the developer options on the Android device.
	“READING” keeps	• Reconnect the Android device.
	flashing.	• If this does not solve the problem, the connected Android
		device does not support [BROWSE MODE]. (	28)
	Playback is intermittent	Turn off the power saving mode on the Android device.
	or sound skips.
	“ANDROID ERROR” /	• Reconnect the Android device.
	“NA DEVICE”	• Restart the Android device.
	“ADD ERROR”	New station creation is unsuccessful.
	“CHECK DEVICE”	Check the Pandora application on your device.
	“NO SKIPS”	The skip limit has been reached.
	“NO STATIONS”	No stations are found.
Pandora	“STATION LIMIT”	The number of registered stations has reached its limit. Retry
		after deleting unnecessary stations from your device.
	“CONNECT ERROR”	Communication is unstable.
	“RATING ERROR”	Registration of thumbs up/thumbs down has failed due to
		insufficient network connectivity.
	“THUMBS N/A”	Registration of thumbs up/thumbs down is not allowed.
	“LICENSE ERROR”	You try to access from a country which Pandora is not
		deliverable.

	Symptom		Remedy
	iHeartRadio	iHeartRadio station cannot	If “Explicit Content” in [Account Settings] is checked in
		be selected.	the web version of iHeartRADIO, custom stations become
			unavailable.
		“NOT CONNECTED”	Link to the application is impossible.
		“CH LOCKED LOCK CODE?”	The selected channel is locked. Enter the correct pass
			code to unlock. ( 15)
		“CHAN UNSUB”	The selected channel is unsubscribed. Call
			1-866-635-2349 in the U.S.A. or 1-877-438-9677 in
			Canada to subscribe. ( 13)
		“CH UNAVAIL”	The selected channel is unavailable. Visit
			www.siriusxm.com for more information about the
			SiriusXM channel lineup.
	Radio	“CHECK ANTENNA”	Check that the antenna and its connection are in good
			condition.
	SiriusXM®
		“CHECK TUNER”	Make sure the SiriusXM Vehicle Tuner is connected to
			the unit.
		“NO SIGNAL”	Make sure the antenna is mounted outside the vehicle.
		“SUBSCRIPTION UPDATED	Your subscription is updated. Press the volume knob to
		– PRESS ENTER TO	continue.
		CONTINUE.”
		“CODE ERROR”	Make sure you have entered the correct pass code.
			( 15)
		“NO CONTENT”	There is insufficient content to start TuneScan.
		“SCAN CANCEL”	TuneScan has been aborted.

26