SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL
HSU-09HR03/R2(DB) HSU-12HR03/R2(DB) HSM09HRAC03/R2(DB) HSM12HRAC03/R2(DB) HSM18HRAC03/R2(DB)
HSU-09HRA103/R2 HSU-12HRA103/R2 HSU-18HRA103/R2
Contents
CAUTIONS |
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
||
PARTS AND FUNCTIONS |
|
|
|
|
|
2 |
||||
|
|
|
||||||||
OPERATION |
|
|
|
|
|
|
3 |
|||
|
|
|
|
|
||||||
MAINTENANCE |
|
|
|
|
6 |
|||||
|
|
|
||||||||
TROUBLE SHOOTING |
|
|
7 |
|||||||
|
Please read this operation manual before using the air conditioner. Keep this operation manual for future reference.
0010523724
Parts and Functions
|
|
Indoor Unit |
|
|
|
Remote controller |
|
|
|
|
|||
|
|
|
|
Inlet |
Air Purifying Filter |
|
Inlet grille |
(inside) |
|
|
||
Outlet |
|
|
Anion generator |
Emergency |
|
(inside) |
||
Switch |
||
|
||
Horizontal flap |
Vertical blade |
|
(adjust up and down air flow |
(adjust left and |
|
Don't adjust it manually) |
right air flow) |
|
|
Display board |
Actual indoor unit may vary from the one shown
in the manual, according to the product purchased.
Display board
1 |
2 |
3 |
4 |
5 |
6 |
7 |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Signal receiver hole
2 COOL display
3 HEAT display
4 TEMP display
5 HEALTH display
(If the unit which you purchased has healthy function,follow it.
If not,please ignore.)
6 Dry display
7 TIMER OFF display
TIMER ON display SLEEP display
Outdoor Unit
OUTLET |
CONNECTING PIPING AND ELECTRICAL WIRING |
INLET |
4 DRAIN HOSE |
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET, "AM "and "PM" stop flashing,while clock starts working.
16 |
|
9. ON/OFF button |
|
||
17 |
10. TIMER ON display |
||||
|
|||||
15 |
|
11. FAN SPEED display |
|||
|
|
|
|
||
14 |
18 |
|
|
|
|
13 |
|
|
|
||
19 |
LOW MED |
HI |
AUTO |
||
12 |
12. LOCK display |
|
|||
|
|
||||
|
20 |
|
|||
11 |
13. SWING display |
|
|||
|
21 |
|
|||
|
14. SLEEP display |
|
|||
|
22 |
|
|||
|
15. HEALTH display |
|
|||
|
|
|
|||
|
|
16. Operation mode display |
|
23 |
|
|
24 |
|
|
25 |
|
|
26 |
|
|
27 |
|
|
28 |
|
2 |
29 |
|
30 |
||
|
1.CODE Used to select CODE A or B which will be displayed on
LCD.Please select A without special explanation. 2.LIGHT button
Control the lightening and extinguishing of the indoor
LED display board. 3. TIMER button
4. CLOCK button
5. SLEEP button
6. MODE button
7. HOUR button
8. HEALTH button
Operation mode AUTO COOL DRY FAN HEAT
Remote controller
17.Signal sending display
18.POWER/SOFT display
19.TEMP display 20.TIMER OFF display
21.CLOCK display
22.TEMP button
23.FAN button
24.SWING button
25. . HEALTH AIRFLOW button
26. FRESH button
27. SET button
28. POWER/SOFT button
29. LOCK button
If pressed, the other buttons
will be disabled.Press it once again,lock will be cancelled.
30. RESET button
When the remote controller appears abnormal,use a sharp pointed article to press
this button to reset the remote controller normal.
The following functions and related displays are not available: 1 26
LIGHT button is not available for HSU-09HRA103/R2 and HSU-12HRA103/R2.
Loading of the battery
|
|
Remove the battery cover; |
2 |
|
1Load the batteries as illustrated. |
|
|
22 R-03 batteries, resetting key |
|
1 |
(cylinder); |
3 |
|
3 Be sure that the loading |
is in line with the" + "/"-"; 4 Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the batteries have been used up.Please change batteries.
If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.
Hint:
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key.
2
Operation
Base Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode
changes as follows: Remote controller:
AUTO COOL DRY FAN HEAT
3.Select temp.setting
Press TEMP+ / TEMP- button
TEMP+ Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting decrease 1oC,if kept depressed, it will decrease rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW MED |
HI |
AUTO |
Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
Operation |
Display Board |
Remote |
Note |
||||
Mode |
|
Controller |
|
||||
|
|
|
|
|
|
|
Under the mode of auto operation, air conditioner |
AUTO |
|
|
|
|
|
|
will automatically select Cool or Heat operation |
|
|
|
|
|
|
according to room temperature. When FAN is set |
|
|
|
|
|
|
|
|
to AUTO, the air conditioner automatically adjusts |
|
|
|
|
|
|
|
the fan speed according to room temperature. |
COOL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
In DRY mode, when room temperature becomes |
DRY |
|
|
|
|
|
|
lower than temp.setting+2oC, unit will run |
|
|
|
|
|
|
intermittently at LOW speed regardless of FAN |
|
|
|
|
|
|
|
|
setting. |
|
|
|
|
|
|
|
|
HEAT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
In FAN operation mode , the unit will not operate in |
FAN |
nothing |
|
|
|
|
|
COOL or HEAT mode but only in FAN mode , |
|
|
|
|
|
setting is disabled. In FAN mode, sleep operation |
||
|
|
|
|
|
|
|
AUTO is not available in FAN mode. And temp. |
|
|
|
|
|
|
|
is not available. |
|
|
|
|
|
|
|
|
Emergency operation and test operation
Emergency Operation: |
Pi |
Use this operation only when the remote controller is defective or lost.
When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation.
In this operation, the system automatically selects the operation modes,cooling or fan or heat,
according to the room. temperature.
Room |
Operation |
Designated |
Timer |
|
Air flow |
|
||||
temperature |
mode |
|
temperature |
mode |
|
|
||||
|
|
|
|
|
||||||
ABOVE 23OC |
COOLING |
|
26OC |
|
NO |
|
AUTOMATIC |
|
||
BELOW 23OC |
HEAT |
|
23OC |
|
NO |
|
AUTOMATIC |
|
||
|
|
|
|
|
|
|
||||
(Cooling only uint |
|
Operation |
Designated |
Timer |
Air flow |
|||||
Room temperature |
|
|
mode |
temperature |
mode |
|||||
BELOW 23OC |
|
|
FAN |
|
26OC |
NO |
AUTOMATIC |
It is not possible to operate in dry mode.
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room |
|
|
temperature is below 16oC, do not use it in the |
Pi Pi |
|
normal operation. |
||
|
||
Continue to press the test operation |
|
|
switch for more than 5 seconds . After |
|
|
you hear the "Pi" sound twice, release |
|
|
your finger from the switch: the cooling |
|
operation starts with the air flow speed "Hi".
Air Flow Direction Adjustment
1.Status display of air flow
Vertical flap
Pos.1 Pos.2 Pos.3
Pos.4 Pos.5 Pos.6 (Auto swing)
2.Left and right air flow adjustment(manual)
Move the vertical blade by a knob on air conditioner to adjust left and right direction referring to Fig.
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
at air outlet if all vertical louvers are adjusted to left or right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY mode , otherwise, condensate water might occur. Note:
When restart after remote turning off, the remote controller will automatically memorize the previous set swing position.
3