Gateway Server E-9520T User Manual

3.4 Mb
Loading...

USER GUIDE

Gateway® E-9520T Server

Contents

Chapter 1: Checking Out Your Gateway Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 System board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hot-swap backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SAS/SATA backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 LED information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Server Companion DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Gateway Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2: Setting Up Your Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setting up the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Protecting from power source problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Removing and installing the bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Starting your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Understanding the power-on self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Turning off your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setting up the operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Initial hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 3: Maintaining Your Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Caring for your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Cleaning your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Preparing for system recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Recording the BIOS configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 System administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Gateway System Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Server security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Identifying your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Updating the baseboard management controller firmware . . . . . . . . . . . . . . 23 Using your Server Companion DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Server Companion DVD contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Viewing documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Installing drivers and programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Updating the BIOS and firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Booting the Server Companion DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Chapter 4: Installing Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Preparing to install components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

i

Contents

www.gateway.com

Selecting a place to work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Gathering the tools you need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Preventing static electricity discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Opening the server case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Closing the server case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Installing and removing drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Removing and installing an optical drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Removing and installing a hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Filling empty drive bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Installing the optional diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Installing memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Installing and removing PCI expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Removing and installing a PCI card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Replacing system fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Replacing the fan cage and fan board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Replacing or adding a processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Replacing a power supply module and power board . . . . . . . . . . . . . . . . . . . .48

Adding an additional power supply module . . . . . . . . . . . . . . . . . . . . . . . . .49

Replacing the power distribution board . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Replacing the hot-swap backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Installing and removing a mezzanine board . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Replacing the CMOS battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Replacing the system board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Chapter 5: Using the BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Opening the BIOS Setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Updating the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Recovering the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Resetting the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Resetting BIOS passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Chapter 6: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Before calling Gateway Customer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Tutoring and training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Safety guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Understanding sensors and sensor readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Sensor type codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 First steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Beep codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 LED information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

ii

www.gateway.com

Contents

Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Optical drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Appendix A: Server Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

System specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 System board specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Electronic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Connector pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Additional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Appendix B: BIOS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Appendix C: Safety, Regulatory, and Legal Information . . . . . . . . . . . . . . . . . . . . . 109

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

iii

Contents

www.gateway.com

iv

CHAPTER 1

Checking Out Your Gateway Server

Front

Back

Interior

System board

Hot-swap backplanes

Getting Help

1

CHAPTER 1: Checking Out Your Gateway Server

www.gateway.com

Front

Optical drive

SMIL connector

Second optical drive (optional)

NMI button

System fault LED

Reset button

NIC status LED

ID button

ID LED

Hard drive cages

Power LED

Power button

Case cover lock

Dual USB ports

Diskette drive (optional)

2

www.gateway.com

Back

Connectors and LEDs

PS/2 mouse port

PS/2 keyboard port

Dual USB ports

Serial port

VGA port

ID LED Dual NIC connectors (RJ-45)

Management port (RJ-45)

Back

AC power connector

Power supply status LED

Power supply module

Case cover thumbscrew

Case cover thumbscrew

3

CHAPTER 1: Checking Out Your Gateway Server

www.gateway.com

Interior

Important

Server components with green handles or retention locks can be hot swapped while the server is on. Server components with blue handles or retention locks can only be removed when the server is turned off.

#

Feature

#

Feature

 

 

 

 

1

Power supply

5

Front panel

 

 

 

 

2

Power distribution board

6

Hard drive bays

 

 

 

 

3

System fans (hot swap)

7

SAS/SATA backplane

 

 

 

 

4

5.25” device bays

8

System board

 

 

 

 

4

www.gateway.com

System board

System board

Connectors

#

Feature

#

Feature

 

 

 

 

1

PCI-X 64-bit/66 MHz expansion slot (J45)

26

Not used

 

 

 

 

2

PCI-X 64-bit/66 MHz expansion slot (J43)

27

Processor power connector (J5)

 

 

 

 

3

PCI 32-bit/33 MHz expansion Slot (J41)

28

Processor 1

 

 

 

 

4

PCI-E x8 expansion slot with x4 speed

29

SMIL connector (J47)

 

(J39)

 

 

 

 

 

 

5

PCI-E x8 expansion slot with x4 speed

30

Processor 2

 

(J37)

 

 

 

 

 

 

6

PCI-E x16 expansion slot with x8 speed

31

Fan board connector (J29)

 

(J35)

 

 

 

 

 

 

5

CHAPTER 1: Checking Out Your Gateway Server

www.gateway.com

#

Feature

#

Feature

 

 

 

 

7

Management port (RJ-45) (J30)

32

Not used

 

 

 

 

8

Dual NIC connector (RJ-45) (J28)

33

PCI-E mezzanine board connector (J33)

 

 

 

 

9

ID LED (CR13)

34

I2C and system ID connector (J46)

10

D-sub VGA port (J24)

35

Server management connector (J34)

 

 

 

 

11

Serial port (J15)

36

COM2 connector (J60)

 

 

 

 

12

Dual USB connector (J12)

37

MFG connector (J48)

 

 

 

 

13

PS/2 keyboard and mouse ports (J10)

38

Onboard USB connector (J61)

 

 

 

 

14

System fan connector (J4)

39

IDE connector (J54)

 

 

 

 

15

System fan connector (J3)

40

Floppy connector (J49)

 

 

 

 

16

Main power connector (J7)

41

PCI-X mezzanine board connector (J44)

 

 

 

 

17

DIMM 1 socket (J11)

42

Front panel USB connector (J56)

 

 

 

 

18

DIMM 2 socket (J13)

43

Mini-SAS connector (J50)

 

 

 

 

19

DIMM 3 socket (J14)

44

Onboard SATA connector 0 (J55)

 

 

 

 

20

DIMM 4 socket (J18)

45

Onboard SATA connector 5 (J51)

 

 

 

 

21

DIMM 5 socket (J21)

46

Chassis intrusion connector (J53)

 

 

 

 

22

DIMM 6 socket (J22)

47

Front panel connector (J57)

 

 

 

 

23

DIMM 7 socket (J23)

48

1x2 pin system configuration jumper 1

 

 

 

(J58)

 

 

 

 

24

DIMM 8 socket (J26)

49

2x5 pin system configuration jumper 2

 

 

 

(J59)

 

 

 

 

25

Power supply I2C connector (J8)

50

Battery (B1)

6

www.gateway.com

Hot-swap backplanes

Hot-swap backplanes

SAS/SATA backplane

#

Feature

#

Feature

 

 

 

I2C and system ID connector

1

SAS/SATA hard drive connector 0

6

2

SAS/SATA hard drive connector 1

7

I2C and system ID connector

3

SAS/SATA hard drive connector 2

8

Backplane power connector

 

 

 

 

4

SAS/SATA hard drive connector 3

9

Backplane SAS connector

 

 

 

 

5

SAS/SATA hard drive connector 4

 

 

 

 

 

 

7

CHAPTER 1: Checking Out Your Gateway Server

www.gateway.com

LED information

See the following table for a description of this server’s LEDs and the information they provide:

LED Name

Function

Location

Color

Description

 

 

 

 

 

 

 

ID

Aid in server

Front panel and

Yellow

On - Server identification

 

identification

back of system

(front)

enabled

 

 

board

Blue (back)

 

 

 

 

 

 

 

 

 

 

System Fault

Visible fault

Front panel

Red

Off - No fault

 

warning

 

 

Blinking - Non-critical

 

 

 

 

system fault

 

 

 

 

On - Critical system fault

 

 

 

 

 

 

 

Hard drive

Indicate drive

On each hard

Blue or Red

Blue (On) - Hard drive okay

tray

status and

drive tray

 

Blue (Blinking) - Hard drive

 

activity

 

 

activity

 

 

 

 

Red (On) - Hard drive fault

 

 

 

 

Red (Blinking) - Hard drive

 

 

 

 

rebuilding

 

 

 

 

Off - No hard drive

 

 

 

 

 

 

 

LAN (front)

Identify NIC

Front panel

Blue

On - LAN link for any NIC

 

status

 

 

Blinking - LAN activity for

 

 

 

 

any NIC

 

 

 

 

Off - No link for any NIC

NIC status

Identify NIC

Front panel and

Green/

 

 

 

 

 

 

LEDs

states

back I/O panel

Yellow

 

 

 

 

 

RJ-45

 

 

 

 

 

 

connectors

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED 1 Green (On) - NIC

 

 

 

 

linked

 

 

 

 

LED 1 Green (Blinking) - NIC

 

 

 

 

activity

 

 

 

 

LED 1 (Off) - No link

 

 

 

 

LED 2 Yellow (On) Link speed

 

 

 

 

1 Gbps

 

 

 

 

LED 2 Yellow (Off) - Link at

 

 

 

 

other speed

 

 

 

 

 

Power LED

Identify the

Front panel

Blue

Off - Power is off (or S5)

 

power state of

 

 

On - Power is on (or S0)

 

the system

 

 

 

 

 

 

 

 

Power supply

Identify power

Power supply

Green or

Green (On) - Power supply

status LED

supply fault

module

Red

good and receiving power

 

 

 

 

Red (On) - Power supply

 

 

 

 

fault

 

 

 

 

Off - Power supply not

 

 

 

 

receiving power

 

 

 

 

 

8

www.gateway.com

Getting Help

Getting Help

In addition to your operating system’s documentation, you can use the following information resources to help you use your server.

Server Companion DVD

Use the Server Companion DVD to access file utilities, Windows Server 2003 drivers, and documentation for your server and its components. For instructions, see Using Your Server Companion DVD.

Gateway Web site

Gateway provides a variety of information on its Web site to help you use your server.

Visit the Gateway Web site at support.gateway.com for:

Technical documentation and product guides

Technical tips and support

Updated hardware drivers

Order status

Frequently asked questions (FAQs)

Telephone support

You can access a wide range of services through your telephone, including customer service, technical support, and information services. For more information, see “Telephone support” on page 66.

9

CHAPTER 1: Checking Out Your Gateway Server

www.gateway.com

10

CHAPTER 2

Setting Up Your Server

Setting up the hardware

Protecting from power source problems

Starting your server

Setting up the operating system

Initial hardware settings

11

CHAPTER 2: Setting Up Your Server

www.gateway.com

Setting up the hardware

Caution

Your server comes with a 3-wire AC power cord(s) fitted with the correct plug style for your region. If the plug(s) does not match the connector on your surge protector, UPS, or wall outlet, do not attempt to modify the plug(s) in any way. Use a surge protector, UPS, or wall outlet that is appropriate for the supplied AC power cord(s).

Important

Keep the server boxes and packing material in case you need to ship the server.

To make sure that your working environment is safe:

Use a clean, dry, flat, stable surface for your server. Allow at least 6 inches at the back of the server for cabling and air circulation.

Use the instructions on your server’s setup poster to set up your hardware.

Use a grounded (three-prong) surge protector. A surge protector helps protect against AC power fluctuations. For additional protection from power outages, we recommend that you use an uninterruptible power supply (UPS).

Avoid subjecting your server to extreme temperature changes. Do not expose your server to direct sunlight, heating ducts, or other heat-generating objects. Damage caused by extreme temperatures is not covered by your warranty. As a general rule, your server is safest at temperatures that are comfortable for you.

Keep your server and magnetic media away from equipment that generates magnetic fields, such as unshielded stereo speakers. Strong magnetic fields can erase data on both diskettes and hard drives. Even a telephone placed too close to the server may cause interference.

Protecting from power source problems

Caution

High voltages can enter your server through the power cord and the modem and network connections. Protect your server by using a surge protector. If you have a modem, use a surge protector that has the appropriate type of modem jack. During an electrical storm, unplug the surge protector and the modem and network cables.

Surge protectors, line conditioners, and uninterruptible power supplies can help protect your server against power source problems.

Surge protectors

During a power surge, the voltage level of electricity coming into your server can increase to far above normal levels and cause data loss or server damage. Protect your server and peripheral devices by connecting them to a surge protector, which absorbs voltage surges and prevents them from reaching your server.

When you purchase a surge protector:

Make sure that the surge protector meets the appropriate product safety certification for your location, such as Underwriters Laboratories (UL).

Check the maximum amount of voltage the protector allows to pass through the line. The lower the voltage, the better the protection for your server.

Check the energy absorption (dissipation) rating. The higher the energy absorption rating, the better the protection for your server.

Line conditioners

A line conditioner protects your server from the small fluctuations in voltage from an electrical supply. Most servers can handle this variation, called line noise, without problems. However, some electrical sources include more line noise than normal. Line noise can also be a problem if your server is located near, or shares a circuit with, a device that causes electromagnetic interference, such as a television or a motor.

Some surge protectors and uninterruptible power supplies include simple line-conditioning capabilities.

12

www.gateway.com

Protecting from power source problems

Uninterruptible power supplies

Use an uninterruptible power supply (UPS) to protect your server from data loss during a total power failure. A UPS uses a battery to keep your server running temporarily during a power failure and lets you save your work and shut down your server. You cannot run your server for an extended period of time while using only the UPS. To buy a UPS, visit accessories.gateway.com.

Removing and installing the bezel

To remove and install the bezel:

1Follow the instructions in “Preventing static electricity discharge” on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server.

2If the server is mounted in a cabinet, remove the server from the cabinet. For instructions, see the instructions that accompanied the rail kit.

3 If the bezel door is installed, unlock (if necessary) and open it.

4Open the server case by following the instructions in “Opening the server case” on page 29.

5Close the bezel door, then pull out on the three retaining tabs on the left side of the bezel to disengage the tabs from the chassis.

Retaining tab

Retaining tab

Retaining tab

13

CHAPTER 2: Setting Up Your Server

www.gateway.com

6Swing the bezel out 45° from the front of the case, then disengage the tabs on the right side of the bezel from the chassis and remove it.

7To reinstall the bezel, align the right side of the bezel with the right side of the chassis at a 45° angle, then insert the three tabs on the right side of the bezel into the slots in the chassis.

8Swing the left side of the bezel in to the chassis until the three tabs on the left side of the bezel snap into place.

9Close the server case by following the instructions in “Closing the server case” on page 30.

14

www.gateway.com

Starting your server

Starting your server

Caution

When you connect peripheral devices to the server, make sure that your server and devices are turned off and the power cords are unplugged.

Before you start your server for the first time:

Make sure that the server and monitor are plugged into a power outlet or surge protector and that the surge protector (if you are using one) is turned on.

Make sure that all cables are connected securely to the correct ports and jacks on the back of the server.

To start the server:

1 Turn on any peripheral devices connected to the server.

2 Press the power button. The power LED turns green.

Power LED

Power button

15

CHAPTER 2: Setting Up Your Server

www.gateway.com

If nothing happens when you press the power button:

Make sure that the power cable(s) is plugged in securely and that your surge protector (if you are using one) is plugged in and turned on.

Make sure that the monitor is connected to the server, plugged into the power outlet or surge protector, and turned on. You may also need to adjust the monitor’s brightness and contrast controls.

If you cannot find the cause of the power loss, contact Gateway Customer Care. For more information, see “Getting Help” on page 9.

3The first time you turn on the server, any pre-installed operating system may begin asking you for configuration settings. See your operating system’s documentation for instructions on configuring advanced settings for your specific network.

Understanding the power-on self-test

When you turn on your server, the power-on self-test (POST) routine checks the server memory and components. If POST finds any problems, the server displays error messages. Write down any error messages that you see, then see “Error messages” on page 68 and “Beep codes” on page 75 for troubleshooting information.

Turning off your server

Every time you turn off your server, first shut down the operating system. You may lose data if you do not follow the correct procedure.

Caution

The power button on the server does not turn off server AC power. To remove AC power from the server, you must

unplug the AC power cords from the wall outlet or power source. The power cords are considered the disconnect device to the main (AC) power.

To turn off the server:

1See the operating system’s documentation or online help for instructions on shutting down the operating system. Whenever possible, you should use the operating system’s shut down procedure instead of pressing the power button.

2 If your server did not turn off automatically, press the power button.

- OR -

Press the reset button to reset the server.

16

www.gateway.com

Setting up the operating system

Setting up the operating system

If you ordered your server with the operating system already installed by Gateway, in most cases it is completely installed and the basic settings are already configured. The Windows Small Business Server operating system may require additional installation, depending on the version you ordered. See your operating system’s documentation for instructions on completing the installation or configuring advanced settings for your specific network.

If you are installing an operating system because it was not already installed by Gateway, see the appropriate installation guide for instructions.

Initial hardware settings

Your server comes from the manufacturer with the correct initial hardware settings to operate your server as configured. However, you might want to change settings to reflect a tasking change, a change in security requirements, or the addition of new resources to your server.

You can change general hardware settings by using the BIOS Setup utility. For information on the BIOS Setup utility, see “Using the BIOS Setup Utility” on page 59. For information on BIOS settings, see “BIOS Settings” on page 97.

17

CHAPTER 2: Setting Up Your Server

www.gateway.com

18

CHAPTER 3

Maintaining Your Server

Caring for your server

Preparing for system recovery

System administration

Identifying your server

Updating the baseboard management controller firmware

Using your Server Companion DVD

19

CHAPTER 3: Maintaining Your Server

www.gateway.com

Caring for your server

To extend the life of your server:

Be careful not to bump or drop your server.

When transporting your server, we recommend that you put it in the original packaging materials.

Keep your server and magnetic media away from equipment that generates magnetic fields, such as unshielded speakers.

Avoid subjecting your server to extreme temperatures. Do not expose your server to heating ducts or other heat-generating objects. Damage caused by extreme temperatures is not covered by your warranty. As a general rule, your server is safest at temperatures that are comfortable for you.

Keep all liquids away from your server. When spilled onto server components, almost any liquid can result in extremely expensive repairs that are not covered under your warranty.

Avoid dusty or dirty work environments. Dust and dirt can clog the internal mechanisms and can cause the server to overheat.

Cleaning your server

Keeping your server clean and the vents free from dust helps keep your server performing at its best. Your server cleaning kit could include:

A soft, lint-free cloth

Glass cleaner

An aerosol can of air with a narrow, straw-like extension

Isopropyl alcohol

Cotton swabs

A tape drive cleaning cartridge (if a tape drive is installed)

A CD drive cleaning kit

Warning

When you shut down your server, the power turns off, but some electrical current still flows through your server. To avoid possible injury from electrical shock, unplug the power cord and all other cables connected to the server.

Cleaning tips

Always turn off your server and other peripheral devices before cleaning any components.

Use a damp, lint-free cloth to clean your server and other parts of your server system. Do not use abrasive or solvent cleaners because they can damage the finish on components.

Keep the cooling vents free of dust. With your server turned off and unplugged, brush the dust away from the vents with a damp cloth, but be careful not to drip any water into the vents.

20

www.gateway.com

Caution

The computer screen is made of specially coated glass and can be scratched or damaged by abrasive or ammonia-based glass cleaners.

Preparing for system recovery

Cleaning the keyboard

You should clean the keyboard occasionally by using an aerosol can of air with a narrow, straw-like extension to remove dust and lint trapped under the keys.

If you spill liquid on the keyboard, turn off your server and turn the keyboard upside down to let the liquid drain. Let the keyboard dry completely before trying to use it again. If the keyboard does not work after it dries, you may need to replace it. Keyboard damage resulting from spilled liquids is not covered by your warranty.

Cleaning the screen

If your computer screen is an LCD, use only a damp, soft cloth to clean it. Never spray water directly onto the screen.

- OR -

If your computer screen is not an LCD, use a soft cloth dampened with glass cleaner to clean the screen. Never spray cleaner directly onto the screen.

Cleaning the tape drive

If you use a tape drive to back up your files, regular maintenance will lengthen the life of the drive. To maintain the drive’s reliability:

Clean the drive monthly with the cleaning cartridge included with the drive.

Remove the tape from the drive whenever the drive is not in use.

Preparing for system recovery

If your system files are corrupted, you may not be able to start the server from the hard drive. Use the Server Companion DVD to start the server and attempt to fix the problem.

Recording the BIOS configuration

To help keep track of your custom changes to BIOS settings and to prepare for system recovery, you should record your BIOS configuration after you have your server set up and working.

To record your BIOS configuration:

1 Print the appendix for “BIOS Settings” on page 97.

2Restart your server, then press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility opens.

3 Record the BIOS settings on your printout.

21

CHAPTER 3: Maintaining Your Server

www.gateway.com

System administration

Gateway System Manager

Gateway System Manager (GSM) lets you manage multiple computers on a Windows network from a single window, then implement commands and policies across the network with a single action. With Gateway System Manager, you can run system management tasks which are triggered by certain events or conditions.

For more information, refer to the Gateway Baseboard Management Controller (BMC) User Guide at http://support.gateway.com/support/default.asp# (by selecting this server from the list). You can also find additional information in the program’s online help.

Server security

Locking the server

To lock the server:

1Remove the bezel lock keys from the inside of the bezel, then snap on the bezel. The handles must be installed for the bezel to snap on. For instructions, see “Removing and installing the bezel” on page 13.

2Insert the key into the lock and rotate it ¼ turn clockwise. To unlock it, rotate the key ¼ turn counter-clockwise.

Using BIOS security passwords

To prevent unauthorized use of the server, you can set server startup passwords.

Set an administrator password to prevent unauthorized access to the BIOS

Setup utility.

To set the BIOS security passwords:

1Restart your server, then press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility opens.

2 Select the Security menu.

3 Select Change Administrator Password.

4 Type the password and press ENTER, then type it again and press ENTER.

5 Save your changes and close the BIOS Setup utility.

To remove a BIOS security password:

1Restart your server, then press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility opens.

22

www.gateway.com

Identifying your server

2 Select the Security menu, then select the password to remove.

3 Enter the current password, then press ENTER.

4For the new password, leave the password field blank, then press ENTER. The password is removed.

Tips & Tricks

Passwords can also be cleared using jumpers on the system board. For instructions, see “Resetting BIOS passwords” on page 64.

Identifying your server

While you are working on a cabinet that contains several slim servers, it can be difficult to keep track of which server or servers you are currently working on. The ID indicator is a yellow LED (front) or a blue LED (back) that you can turn on to help you locate the correct server. For the System ID indicator to turn on, the server does not need to be turned on, but it does need to be plugged in.

To turn on the ID LED:

1Press the ID button on the front panel of the server. The yellow ID LED (front) and the blue ID LED (back) turn on. For the location of these LEDs, see “LED information” on page 8.

2 To turn off the indicator, press the ID button.

Updating the baseboard management controller firmware

The baseboard management controller (BMC) performs several system management functions such as:

Monitoring server components (FRU) and sensor data records (SDR) (the information provided depends on the option selected)

Managing non-volatile storage for the system event log and sensor data records

Interfacing with the emergency management port to send alerts and interact with remote management systems

Fault resilient booting (the extent depends on the option selected)

You should update the BMC firmware when Gateway Customer Care has instructed you to update it.

To update the BMC firmware:

1Download the BMC update file from support.gateway.com and copy onto a USB Disk-on-key device.

2Turn off and boot the system from the SCDVD, then open the command line.

3 At the command line, change directories to the USB Disk-on-key device.

23

CHAPTER 3: Maintaining Your Server

www.gateway.com

4 Run the update utility on the USB Disk-on-key device.

Using your Server Companion DVD

You can use your Server Companion DVD to:

Install hardware drivers

Install programs

Upgrade the BIOS and firmware

View server documentation

Server Companion DVD contents

The Server Companion DVD is a tool you can use to help maintain your server.

The DVD contains:

Computer and component documentation

Drivers and utilities for servers running Windows 2003 Server

Viewing documents

The DVD contains documents for your server and for some optional components. You can view the documents with the Acrobat® Reader® version 4.0 and above.

To view documents:

1Insert the Server Companion DVD into the DVD drive on a computer running the Windows operating system. The Gateway Application and Driver Recovery window opens.

- OR -

If the window does not open, run the file Runmenu.exe on the DVD.

2 Click Documentation. The server document list opens.

3 Click the title of the document you want to view. The document opens.

4To access files manually, open the Docs\Manuals folder on the Server Companion DVD.

To install Acrobat Reader 7:

Click the link for Acrobat on the Documentation page. - OR -

Run Docs\Reader\app21279\Setup.exe from the Server Companion

DVD.

24

www.gateway.com

Using your Server Companion DVD

Installing drivers and programs

Important

The Server Companion DVD’s Gateway Application and Driver Recovery utility works only in Windows operating systems.

You can install drivers and programs directly onto the server by using the Server Companion DVD. You can also extract drivers onto diskette from the DVD at any Windows workstation.

To install drivers and programs at the server:

1Insert the Server Companion DVD into your server’s DVD drive. The

Gateway Application and Driver Recovery window opens. - OR -

If the window does not open automatically, run the file Runmenu.exe on the DVD.

A list of programs and drivers that you can install appears in the Drivers and Application Recovery list.

2Click the program or driver you want to install, then click Install. Follow any on-screen instructions.

To access the files manually, open the Drivers folder on the Server Companion DVD, then open the appropriate subfolder.

To extract drivers and programs to diskettes:

1Insert the Server Companion DVD into your server’s DVD drive. The

Gateway Application and Driver Recovery window opens.

- OR -

If the window does not open automatically, run the file Runmenu.exe on the DVD.

2 Click Extract Drivers.

3Click your server model and server operation system at the right of the window, then click Search. A list of programs and drivers that you can create diskettes for appears in the Drivers and Application Recovery list.

4Click the program or driver you want to extract, then click Extract. Follow any on-screen instructions.

To access the files manually, open the Drivers folder on the Server

Companion DVD, then open the appropriate subfolder.

Updating the BIOS and firmware

To update the BIOS and firmware:

1Download the BIOS update file and firmware from support.gateway.com and copy onto a USB Disk-on-key device.

2Turn off and boot the system from the SCDVD, then open the command line.

25

CHAPTER 3: Maintaining Your Server

www.gateway.com

3 At the command line, change directories to the USB Disk-on-key device.

4 Run the update utility batchfile on the USB Disk-on-key device.

Booting the Server Companion DVD

Important

Although the Server Companion DVD is bootable, it does not include network operating system files and is not intended to restore your operating system.

By booting the Server Companion DVD you can re-install the Operating System, repair applications and drivers, or exit to the command prompt.

To boot to this DVD:

1With your server turned on, insert the Server Companion DVD into the DVD drive.

2 Restart your server. A message appears asking you to select an option.

3Press any key to boot from the DVD. The Gateway Options Main Menu appears.

4Follow any on-screen instructions.

You can use the options in this menu to reformat your hard drive, create mass-storage driver disks, or reload Windows and selected applications.

26

CHAPTER 4

Installing Components

Preparing to install components

Preventing static electricity discharge

Opening the server case

Closing the server case

Installing and removing drives

Installing memory

Installing and removing PCI expansion cards

Replacing system fans

Replacing or adding a processor

Replacing a power supply module and power board

Replacing the hot-swap backplanes

Replacing the CMOS battery

Replacing the system board

27

CHAPTER 4: Installing Components

www.gateway.com

Preparing to install components

Selecting a place to work

Work on your server in an area that:

Is clean (avoid dusty areas).

Is a low-static environment (avoid carpeted areas).

Has a stable surface on which to set your server.

Has enough room to place all of your server parts.

Is near a grounded outlet so you can test your server after installation.

Is near a telephone (in case you need help from Gateway Customer Care). The telephone must be directly connected to a telephone jack and cannot be connected to your server.

Gathering the tools you need

Tips & Tricks

Blue latches, thumbscrews, or connectors

indicate tool-less components.

Green latches and connectors indicate Some tools and supplies that you may need to work on your server are:

hot-swappable components.

A notebook to take notes

A Phillips screwdriver

A small flat-blade screwdriver

Small containers to store various types of screws

A grounding wrist strap (available at most electronic stores)

Getting Help

If you have questions about performing any of these procedures, contact

Gateway Customer Care. For more information, see “Getting Help” on page 9.

Preventing static electricity discharge

Warning

To avoid exposure to dangerous electrical voltages and moving parts, turn off your server and unplug the power cords and modem cable before opening the server case.

Warning

To prevent risk of electric shock, do not insert any object into the vent holes of the power supply.

The components inside your server are extremely sensitive to static electricity, also known as electrostatic discharge (ESD).

Before working with server components, follow these guidelines:

Turn off the server, then unplug the power cords and all other cables.

Press the power button to drain any residual power from the server.

Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare metal part of the server. You can also touch a bare metal surface on the back of the server with your finger.

Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam.

28

www.gateway.com

Caution

ESD can permanently damage electrostatic discharge-sensitive components in the server. Prevent ESD damage by following ESD guidelines every time you open the server case.

Opening the server case

Avoid working on the server when your work area is extremely humid.

Remove components from their antistatic bags only when you are ready to use them. Do not lay components on the outside of antistatic bags because only the inside of the bags provide electrostatic protection.

Always hold expansion cards by their edges or their metal mounting brackets. Avoid touching the edge connectors and components on the cards. Never slide expansion cards or components over any surface.

Opening the server case

Caution

For correct cooling and air flow, always reinstall the cover before you turn on the server. Operating the server without the cover in place will cause the server to overheat.

Warning

This server may have two power cords. To disconnect internal AC power, you must unplug both power cords.

Because the components inside your server are extremely sensitive to static electricity, make sure that you follow the instructions at the beginning of this chapter to avoid static electricity damage.

To open the server:

1Follow the instructions in “Preventing static electricity discharge” on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server.

2 If the bezel is installed, unlock and open it.

3If the server is mounted in a cabinet, remove the server from the cabinet. For instructions, see the instructions that accompanied the rail kit.

4 Place the server on a stable, non-skid surface.

5 Unlock the case cover lock on the front panel of the case.

Case cover lock

29

CHAPTER 4: Installing Components

www.gateway.com

6 Loosen the two thumbscrews (1) on the back of the cover.

7Slide the cover (2) toward the back of the case, then remove it from the case.

Closing the server case

To close the server case:

1Make sure that all of the internal cables are arranged inside the case so they will not be pinched when you close the case.

2Place the cover on the side of the case, then slide it forward until it snaps into place.

3 Tighten the two thumbscrews to hold the cover in place.

4Lock the case cover lock on the front panel of the case, then close the bezel.

5 Reconnect the power cords and all other cables.

30

www.gateway.com

Installing and removing drives

Installing and removing drives

Your server’s basic configuration includes one optical drive and as many as 10 3.5-inch SATA or SAS hot-swap hard drives. You can also add an optional diskette drive.

As you prepare to install drives, remember:

Before you install a drive, see the drive’s documentation for information on configuring the drive, setting drive jumpers, and attaching cables.

You may need to configure the drives you install using the BIOS Setup utility. Press F2 at startup to open the BIOS Setup utility.

Removing and installing an optical drive

Caution

The optical drive is not hot-swappable. Before installing or removing the drive, make sure that power is turned off and the power cord(s) is unplugged.

Important

The hard drive carriers shown in these illustrations may look different than the actual hard drive carriers in your server.

To remove and install an optical drive:

1Follow the instructions in “Preventing static electricity discharge” on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server.

2 Follow the instructions in “Opening the server case” on page 29.

3 Unlock the bezel (if necessary) and remove it by pulling it from the chassis.

4 Remove the data and power cables from the back of the optical drive.

5If you are removing the optical drive from the tower configuration, rotate the release latch (1) counter-clockwise and pull the optical drive (2) out of the chassis.

- OR -

31

CHAPTER 4: Installing Components

www.gateway.com

If you are removing the optical drive from the rack configuration, press the release tab (1) marked “PUSH” and pull the optical drive (2) out of the chassis.

6 Remove the four screws (3) from the sides of the optical drive.

7Install the four screws (1) you removed in the previous step on the sides of the new optical drive.

32

+ 88 hidden pages