Feiyutech G4S User Manual
G4S 3-Axis Handheld Gimbal
Suitable for GoPro HERO 4 / HERO 3+ / HERO 3
Beginner Guide
1
Attention !
!
Remove the power switch
cap, insert two 18350
batteries into the handle.
Product Appearance Instructions
2
( 1 ) Please inst all the suitable camera f irst before pow er on the Gimbal.
( 2 ) Please turn o ff the power when n ot in use.
18350
4
1
18350
Mount the camera carefully to
the mounting bracket and make
sure the camera is firmly connected
with the MINI-USB 10Pin.
Power On / Off
Power On: Single tap the function button,the
gimbal shall be powered on after 2 seconds.
Power Off: Hold down the function button for
3 seconds to turn off the gimbal.
Attention: Turn the gimbal on
after ensuring the camera is secure.
Rolling
Applicable to the firmware V1.25 and above version
2 3
MINI-USB
10Pin
Assembly the clipMount the CameraInsert The Batteries
Press the clip at both ends of the
clip, clip it as above picture.
EN
Version 2.0
Joystick
You can control
the direction by
the joystick
Operation Instructions
3
Indicator
Light
Status
LED Status Mode / Status
Single flash
Double flashes
Three flashes
Flash quickly
Panning mode
Panning and Tilting mode
Standby
Lock mode / Initialize the gimbalAlways on
Rolling angle adjustment /
Initialization failure / Malfunction
Working Mode Instructions
Panning Mode
Lock Mode
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted. Panning and Tilng Mode
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Function Button
( Indicator Light )
Turn on/off
Switch operating modes
For other functions
The working mode and
function can be identified
by the LED status
JoystickJoystick
Joystick Control
Joystick Direction
Up
Down
Left
Other Function
Inversion Mode
When in any working mode, press the function button
for three times in succession, the Gimbal will enter into the inversion mode
and switch to the Panning Mode automatically.
Invert the Gimbal to capture more excited scenes easily by switching mode
combination. When in inversion working condition press the function button
for three times in succession to reset the Gimbal back to the original state.
Reset
Reset the tilting axis of the gimbal to initial orientation
and initial mode.
Standby
In standby model, keep the gimbal in power-up state,
the motor stops working, the indicator light flashes for
three times, and single tap again to wake the gimbal.
Operating Instructions of Function Button
Operation
Single tap
Double tap
Triple tap
Quadruple tap
Tap button for six times Please refer to“Gimbal Horizontal Angle Adjustment”for operations
Long press for 1 second Standby
Long press for 3 seconds
Video Output
4
Function
Panning Mode / Lock Mode
Panning and Tilting Mode
Inversion Mode
Reset
Rolling angle adjustment
Power off
Explanation
Single tap to switch between panning mode and lock mode
Under panning and tilting mode, single tap to switch to lock mode
It is possible to switch to other modes under inversion mode,
triple tap again to exit inversion mode and reset
Reset the tilting axis of the gimbal to initial orientation and initial mode
Single tap again to awake the gimbal, or triple tap
to initialize the gimbal
UP
Down
Left
RightRight
Panning
360°360°
360°
Function
Interface
Tilting
360°
Rolling
If any comments or suggestions please do not hesitate
to e-mail us directly : service@feiyu-tech.com
Tilting
Panning
Joystick
Function Button
（ ON / OFF ）
1/4 Inch Screw Hole
Indicator
Indicator Explanation
LED Status
Blue light flashes
three times
Blue light flashes
twice
Blue light flashes
once
Blue light keeps
flashing
If the indicator light flashes red, the
Gimbal will not work correctly due to
an error.
Explain
Full Power
Enough Power
Low Power
No Power
Video
GND
Function
Interface
Read the GoPro SD card and Charge the GoPro
5
G4S 3-Axis handheld gimbal has a mini to micro port, It can connect the GoPro with a micro usb cable. You can read the GoPro SD card and
Charge the GoPro without dismount the GoPro, and it works when the gimbal is powered off.
The GoPro charging switch and the SD card reading switch works independently, and it works when the gimbal is powered off. The default is off.
Video Output Cable
Video / SD
reading switch
V
GoPro Mini
C
to Micro port
GoPro charging
switch
Analog Monitor
( Equipped By Users )
OFF
V
ON
micro port
OFF
C
ON
USB Cable
When the gimbal and GoPro are
powered on , connect the Analog
Monitor to the function port with
the Video Output Cable, to output
the video to the Analog Monitor.
Read the GoPro SD card and
charge the GoPro without dismount
the GoPro
PC
Firmware Upgrade
6
Gimbal Horizontal Angle Adjustment
8
Attention !
!
Make sure that the
connection to the
mini port
USB Cable
Upgrade steps
Download and install the USB driver and the software for updating and the latest firmware
Function
Interface
Remote Control（Optional Item）
7
(1)
from www.feiyu-tech.com
Connect the USB cable to mini port as the diagram. Attention please use the USB connector.
(2)
Please update the firmware as the manual.
(3)
computer is done by the
USB Connector
Wireless Remote Control
USB Cable
Joystick
Function
Button
Operation
Long press for 0.5 second
Wireless
remote control
!
Please install
the receiver properly
before power on
Long press for 3 seconds
Tip：It will be automatically powered
off to save battery if there is no
operation within three minutes.
Function
Interface
Power on / off
Receiver
for wireless
remote control
Power
ON
OFF
Function
Interface
Steps to connect wireless remote control:
Open the wireless remote control.
1
Install the receiver for wireless remote control: Insert the receiver for
2
wireless remote control into the function port of gimbal .
3
Open the gimbal.
Use the wireless remote control to control the gimbal.
4
Charging
Remote Control Distance
Match Code
Keep the gimbal powered on, restart the remote control and
connect the receiver of RC to the gimbal, press the remote control function
button for 7 times in 5 seconds, if the indicator on the RC flashes 5 times it
means the receiver and the transmitter of RC match successfully, then
customer can control the gimbal by the RC.
▲ RC needs to be match code whenever the following situations：
（1）Connecting properly but still control in fail.
（2）Change the receiver or wireless remote control
mini port
Direction button
of the wired remote control
Up
Left
Connect the Micro interface of wireless remote control with 5V
charger(Not included) by USB cable.
15 meters in an open environment.
Remote Control Operation Instructions
Operation
Single Tap
Double Tap
Triple Tap
Quadruple Tap
Tap Button Six Times
Tap Button Seven Times
Long Press For 3 Second
Note: The joystick and function button will be disabled after connecting with the remote control.
Explanation
Panning Mode / Lock Mode
Panning and Tilting Mode
Inversion Mode
Reset (Restore to the boot-up state)
Calibration Using Remote Control
Match Code Mode
StandbyLong Press For 1 Second
Turn Off The Gimbal and RC
Wireless RC
Wireless RC
Remark
Single tap to switch between panning mode and lock mode
Under panning and tilting mode, single tap to switch to lock mode
It is possible to switch to other modes under inversion mode, triple tap
again to exit inversion mode and reset
Reset the tilting axis of the gimbal to initial orientatiozn and initial mode
Please refer to“Gimbal Horizontal Angle Adjustment”for operations
Match code when connecting properly but still control in fail or change
the receiver/wireless remote control.
Single tap again to awake the gimbal, or triple tap to initialize the gimbal
Wired Remote Control
micro port
Down
Right
Upgrade........
PC
Function
Button
Direction
Button
The horizontal angle needs to be adjusted
whenever the following situations happen
to the gimbal, user can adjust the horizontal
angle by gimbal initialization and joystick.
（1）The tilt angle is not leveled with the horizontal
surface.
（2）The roll angle is not parallel to the horizontal
surface.
（3）Under lock mode, the panning angle drifts.
Initialize the gimbal
Specification
9
Vertical Tilting Angle
Rolls Angle
Horizontal Panning Angle
Tilting Increments
Panning Increments Weight
Standard And Optional Accessories
10
Charger
Input: DC 5V
Output: DC 4.2V
Rechargeable
Battery
Type：18350
360°
360°
2°/s ~ 75°/s
č Ď
3°/s ~ 150°/s
Video Output
Cable
Adjusting steps:
STEP 1
( 1 ) After powering the gimbal on, hold down the function button for one second to enter
standby mode, and the LED indicator shall flash for three times;
( 2 ) Consecutively tap the function button for three times, LED indicator shall be always
on, place the gimbal on a flat surface and keep it stationary;
( 3 ) When the initialization is completed, the LED indicator will flash for three times.
Afterward pick up the gimbal and single tap to awake the gimbal.
When the initialization failed, the LED indicator will flash quickly, repeat step (2) & (3)
to reinitialize.
After finished the , the rolling angle still not parallel to the horizontal surface,
you can use the joystick to adjust the rolling angle according to .
STEP 2
Tap button for six times for roll angle adjustment, the tilt
and roll angle restore to the horizontal status. Under the
roll angle adjustment state, move the joystick to the left
or to the right to adjust the roll angle, single tap again to
save the setting and exit after adjusting.
Working Voltage
Overload Current Protection
Usage Time 3 ~ 5 Hours
Adaption
DIS C LAI M ER
G4S 3-Axis Handhled Gimbal is a feature-rich camera stabilizer, yet
lightweight and portable.
Prohibit any user for any illegal purpose. Users will be responsible for
all behaviors of purchase and use products.
The Company assumes no liability for any risks related to or resulting
from the debug and use of this product (including the direct, indirect or
third-party losses).
For any unknown sources of using, we will not be at any services.
Feiyu Tech reserves the right to amend this manual and the terms and
conditions of use the gimbal at any time.
Initialize the gimbal
STEP 1
Rolling angle adjustment
Note: Please adjust in this state
6.0 V ~ 9 V360°
800 mA
GoPro HERO 4 / HERO3+ / HERO3
260 g (Without batteries & camera)
How to Charging
mini port
USB CableUSB Connector
USB Cable
ATTENTION
Please assemble the gimbal in accordance to the diagram provided .
Please upgrade the firmware and configuration settings with the
provided USB data cable.
Please charge the battery with the provided battery charger.
Please install the camera securely before powering on the gimbal.
When the gimbal is not in use or placed on the table, please
ensure it is powered off.
Please visit the official website of Feiyu Tech
to get related information: www.feiyu-tech.com
Technical support: service@feiyu-tech.com
STEP 2
USB Power
Adapter
（Not included）
Everyone
Can Make a Movie
Loading...