FeiYu Tech G4 User Manual

Beginner Guide

Attention !

Please install the suitable camera first before power on the Gimbal.

FY-G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible with GoPro LCD backpack and the cameras with the same size.

Insert The Batteries

Remove the power switch cap, insert two 18350 batteries into the handle.

Power On

Confirm the camera is installed well,then press the power button to turn on the Gimbal.

Install The Camera

Install the GoPro camera by the special Thumb Screw. And make sure it is fixed well.

Mode Switching

When the Gimbal is working, you can press the function button to switch among the three working modes and a special working condition freely.

(Details of working modes please refer to the instructions of working modes)

FEIYU-EN-1

Working Mode Instructions

Function Button

Identify the working mode via switch to different status of the indicator light.

Use for switching working modes.

Special Working Condition (Inversion Mode):

When in any working mode, press the function button for three times in succession, the Gimbal enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset the Gimbal back to the original state.

Working Mode Instructions

Heading Follow Mode：Camera Pitch and Roll Angles remain constant,

heading follows the handheld position. Heading And Pitch Follow Mode：Camera Roll Angle remains constant.

Heading and Pitch follow the handheld position.

Heading Lock Mode: Heading, Pitch and Roll are all locked to point at one position.

Item LED Status Function Explanation

Single Press

Double Press

Long Press For 1 Second On Constantly Heading,Pitch And Roll Are All Locked

Filming Skill

Smooth And Steady Filming:

How To Adjust The Pitching Angle:

Hold the Gimbal at the desired angle, then press the button once to reengage “Heading Follow Mode” in order to lock the angle of desired pitch.

Selfie:

Turn the Gimbal 180°so the function interface is facing you. Then, simply adjust the angle of pitch to the desired angle by utilizing the “Heading And Pitch Follow Mode”which described above and then switch back to “Heading Follow Mode”. Once complete you can film yourself with ease.

Flexible Use Of Inversion Mode: inversion mode and help to captured low angle view more easily. If filming with moving forward at a high speed, keep the handle roughly parallel with the ground will be helpful.

Handheld the Gimbal, keep stable for movement, keep light and steady for walking.

Single Flashes Heading Follow Mode

Double Flashes Heading And Pitch Follow Mode

Double press the function button to enter into“Heading And Pitch Follow Mode”.

Press the function button for three times in succession, the Gimbal switch to the

Product Appearance Instructions

Pitch Axis

M2×22 Knurled Thumb Screw

Heading Axis

Function Interface

If any comments or suggestions please do not hesitate to e-mail us directly : service@feiyu-tech.com

Roll Axis

Video Input And Camera Charging Interface

Function Button

Power Switch

Indicator

Indicator Explanation

LED Status

Blue light flashes three times

Blue light flashes twice

Blue light flashes once

Blue light keeps flashing

The indicator flashes in red light when in working, it will prompt the Gimbal at fault.

Explain

Full Power

Enough Power

Low Power

No Power

Standard And Optional Accessories

Standard Accessories

USB

USB Mini

USB Cable

Charger

Type: 16340/18350 Input: DC 5V Min 800mA

Output: DC 4.2V

Power Adapter European Standard

Rechargeable Battery

Type: 18350

Connecter

Extension Knurled Thumb Screw

USB Connector

Correct Method For Using USB Data Cable

Please refer to following method to proper usage, otherwise it may cause damage to

the device itself and other equipment.

Battery Charging:

plug into the Micro interface on the charger , and the USB terminal plug to the power adapter, then connect to the US Connecter according to needed .

Connect The Computer:

terminal insert to the function interface on the gimbal and the USB terminal insert to the USB connecter then connect to the computer for firmware upgrade or parameters configuration (Please

connect the USB cable to the computer with the USB connector, otherwise the interface of the computer will be damaged ).

Please refer to the instructions of the function interface for pecific details.

Optional Accessories

Name Remote

Control Runtime

Extension Accessory

Extension Bar

Video And Power Cable

We will keep releasing more FY-G4 accessories. More details please visit our official website: www.feiyu-tech.com

The USB Mini terminal of the USB cable

Remove the batteries, the USB Mini

Function Description

Ample buttons can realize the adjustment of heading & pitch angle, mode switching etc.

Extend the capacity space for battery to make the runtime longer.

Spiral design of the extension bar can be

perfect combination with G4 power switch；

Extended length is optional, it will help to enjoy a different visual easily.

The Gimbal can power supply for the Gopro camera, and analog video signal can output through this cable.

( Please connect the analoy monitor for displaying )

Function Interface Instructions

Video And Camera Charging Interface

Please Remove

The Batteries Before Upgrading

Firmware Upgrade Instruction

Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware then unzip the RAR file.Remove the batteries and refer to the connection diagram to connect the gimbal with the computer. Please refer to the manual of update operation to upgrading,otherwise the Gimbal will be abnormal.

Attention : Please be sure to connect the computer with the USB connector.

Parameters Configuration

The heading following speed can be configurate through parameter setting software.User can adjust to the desired following speed mode according to the requirements of filming scene. Three modes for optional: “SLOW” mode, “NORMAL” mode , “FAST” mode. Default setting is “NORMAL” mode.

Attention : Please be sure to connect the computer with the USB connector.

Gimbal Calibration

The Gimbal attitude can be calibrate through parameter setting software. User can adjust the pitch and roll in a small angle to achieve more accuracy filming scene. Please insert the batteries then refer to the connection diagram to connect the gimbal with the computer for caliration.

Attention : Please be sure to connect the computer with the USB connector.

Function Interface

Extension Bar Instructions (Optional Item)

With the special designed switch, the extension bar can be added directly. Allows to shoot the distance images more easily. Special design allows for flexible extension.

If any comments or suggestions please do not hesitate to e-mail us directly : service@feiyu-tech.com

Function Interface

Aenon: Be sure to connect the computer with the USB connecter

Extension Bar Diagram

USB Cable

Analog Monitor

Remote Control

350mm

Extension Bar Size

USB Connector

After connect the video cable, the analog monitor connect to the function interface then it will display the video.

Connect the remote control to the function interface, heading & pitch angle adjustment and mode switching can be operation from a distance .

Upgrade........

Interface for power supply the GoPro camera and GoPro dedicated analog video signal input access port

This interface can be output 5 voltage and input analog video signal of GoPro. Connect the power cable, power supply for the GoPro camera. Connect the video cable, input analog video signal of GoPro.

Note: The power cable and the video cable doesn’t includes in the standard package, it’s a optional item.

Initialize The FY-G4 Gimbal

Initialization Instructions

1. Install the camera properly.

2. Gimbal placed on stationary flat and keep motionless.

3. Power on the Gimbal.

4. The Gimbal is activate and it will initialize automatically. Pick up the Gimbal to work normally.

FY-G4 needs to be initialized whenever the following situations appear after power on

1. After power on, the angle of pitch is not level with the horizon line.

2. After power on, the angle of roll is not parallel with the horizon line.

3. When the gimbal is in heading lock, the angle of heading moves frequently (heading is not stationary).

Specification

Items Min Standard Max Remarks

Working Voltage Pitch Angle Roll Angle Heading Angle Heading Angle Pitch Following Rate Heading Following Rate Static Attitude Tracking Accuracy

Φ23mm

Motion Attitude Tracking Accuracy Overload Current Protection

Weight

Attention

6.0V

-160（Down）

-50

-160（Left）

-50

2°/ Sec 3°/ Sec

0.01

0.1

8.4V

0（Horizontal） 0（Horizontal）

0.02

0.2

800mA

265g

DISCLAIMER

FY-G4 handheld gimbal is an excellent camera stabilizer,lightweight and portable.

Prohibit any user for any illegal purpose. Users will be responsible for all behavior of purchase and use products.

The Guilin Feiyu Electronic Technology Co. and our associates are not responsible for any damages or liabilities caused by the use of this product.

For any unknown sources or using, we will not be any service.

Feiyu Tech reserves the right to amend this manual and the terms and conditions of use the gimbal at any time.

Motionless Flat Surface

17.0V

+160（Up）

+50 +160

+50

75°/ Sec 150°/ Sec

0.05

0.5

ATTENTION

Please correct assemble the gimbal according to the diagram .

Please upgrading firmware and configurate parameters with the standard configuration USB date cable.

Please battery charging with the standard configuration charger.

Please install the camera well before power on the Gimbal.

Please visit the official website of Feiyu Tech to get related information:

Handheld In Horizontal

Handheld In Vertical

Handheld In Horizontal

Gimbal In Static Mode Motor Overload<2G

Without Batteries & Camera

www.feiyu-tech.com