Feiyutech WGS User Manual

FY WGS 3 Axis Wearable Gimbal is compatible with Gopro HERO4 Session

Introduction

FY WGS is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is compatible with

GoPro HERO4 Session and other cameras with the same dimensions. The FY WGS is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor for

action cameras. A GoPro T-Clamp adapter is packaged with every FY WGS. Users can attach the gimbal to any accessories supporting the GoPro three-prong mount. The FY WGS also contains two 1/4" tripod mounts on its gimbal body, allowing the gimbal to be mounted in different orientations to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).

Install

STEP 1

Remove the screws on the battery compartment, insert two16340 batteries and tighten the screws.

WARNING !WARNING !

Do not power on the

gimbal before completing

all the installation steps.

STEP 2 STEP 3

Mount the camera carefully to the mounting bracket and tighten the screws.

Power on: Ensure the camera is mounted securely, then hold down the function button for 2 seconds to turn on the gimbal.

Power off: Hold down the function button for 3 seconds to turn off the gimbal.

Camera In RightCamera In Right

Vertical

POWERING

ON / OFF

Accessories For 1/4 Inch Screws

Long screw

T-Clamp

Please choose one way:

Use the 3M Adhesive to fix the bottom of the Gimbal.

Use GoPro Accessories, mount the provided T-clamp to the side or the bottom of the gimbal. Attach T-clamp to any accessories supporting the standard GoPro three-prong mount.

The gimbal can also be mounted directly to other accessories using the standard 1/4" tripod mount. Tighten all screws and ensure it is firmly mounted before using the gimbal.

Forward Inverted

Hexagonal Socket Head Cap Screw

Adhesive

Tilting Axis

Function Button

OFF

（

）

Manual Version 1.0

Rolling Axis

Panning Axis

Function Interface

Camera in Left Camera in Left Camera in Left

Camera In

Right

Operation

Function

Button

Operating Modes and Functions

Mode #1 - Panning Mode

Mode #2 - Panning and Tilng Mode Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.

Mode #3 - Lock Mode

Inversion Mode

Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times while in Inverted Mode to switch back to the original orientation.

Manual Pulling Locking

After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning Mode and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.

Reset

Pressing the function button four consecutive times will reset the gimbal to initial orientation.

Tilt and Level Calibration By using the optional FY remote control, tilt and level can be adjusted without connection to a computer.

For more information, please refer to FY remote control section in the instruction manual.

Switch between different operating modes by pressing the function button. The LED light will flash distinctively to indicate different operating modes.

Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.

Camera stays in its current orientation. All panning, tilting and rolls are restricted.

Tilting

Function

Button

Panning

Function Button Quick Reference

Operation LED Status

Single Tap

Double Tap

Triple Tap

Quadruple Tap

* When the gimbal is in the Inverted Mode it will revert back to the original orientation after three press. When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.

LED Flashes Once

LED Flashes Twice

LED Flashes Once

Function Explanation

Panning Mode

Panning and Tilting Mode

Inversion Mode

Reset

Operation LED Status Function

Long Press For 1 Second

Long Press For 2 Second

Long Press For 3 Second

On Constantly

Turn On And Switch To The Mode’s LED Status

Turn Off After A moment

Lock Mode

Power On

Shutdown

Rolling

T-Clamp Screw Hole

1/4 Inch Screw Hole

Screws For The Battery Compartment

T-Clamp Screw Hole

Accessories

Charger

Input: DC 5V Min 800mA Output: DC 4.2V

Rechargeable Battery

Type: 16340

M 1.5 Allen Key

USB CableUSB Connector

HexagonalSocket

HeadCap Screw

M2 * 6mm

Curved Adhesive

Mounts

T-Clamp

Quick-Release

Buckle

Long screw

3M Adhesive

How to Charging

USB Cable

5V USB Power Adapter （Not Included）

FY Remote Control (Optional Item)

Joystick

Function

Function Interface

Tip：The Remote Control will be automatically powered off to save battery if there is no operation within three minutes.

Receiver

for wireless

remote control

Please install the receiver properly before power on

Wireless

remote control

Wireless Remote Control

Steps to connect wireless remote control:

Open the wireless remote control.

Install the receiver for wireless remote control: Insert the receiver for

wireless remote control into the function port of gimbal . Open the gimbal: Long press the function button on gimbal for two

seconds to turn on the gimbal.

Use the wireless remote control to control the gimbal.

Charging

Remote Control Distance

Match Code

Keep the gimbal powered on, restart the remote control and connect the receiver of RC to the gimbal, press the remote control function button for 7 times in 5 seconds, if the indicator on the RC flashes 5 times it means the receiver and the transmitter of RC match successfully, then customer can control the gimbal by the RC.

▲ RC needs to be match code whenever the following situations：（1）Connecting properly but still control in fail. （2）Change the receiver or wireless remote control.

Connect the Micro interface of wireless remote control with 5V charger by USB cable.

15 meters in an open environment.

Button

Operation

Long press for

0.5 second Long press for

3 seconds

Note:

With the remote control, you can switch the gimbal mode or adjust the angle from a distance.

Wired remote control

Power on / off

Power

OFF

Function Interface

Direction Button

UP LEFT RIGHTDOWN

USB Data Cable for RC

Remote Control Operation Instructions

Operation

Single Tap

Double Tap

Triple Tap Triple tap againInversion Mode

Quadruple Tap Reset

Tap Button Six Times

Tap Button Seven Times

Long Press For 1 Second

Long Press For 3 Second

Explanation

Mode #1 Panning Mode

Mode #2 Panning and Tilting Mode

Calibration Using Remote Control

Match Code Mode

Mode #3 Lock Mode

Turn Off The Gimbal

Wireless RC

Remark

,exit inversion mode into original status

Single tap ,exit calibration and enter standby. Wake the gimbal by pressing the function button once again

Match code when connecting properly but still control in fail or change the receiver/wireless remote control.

The function button on the Gimbal will be disabled after connect the Remote Control

Function

Button

Direction

Button

Firmware Upgrade

Be sure to insert the

batteries before upgrading

Function Interface

USB Cable

WARNING

Make sure that the connection to the computer is done by the

USB Connector

Upgrade........

Firmware Upgrade Instruction

Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware. Unzip the compressed file locally to your computer. Refer to the connection diagram on how to connect the gimbal with the computer. Please follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.

Attention : Please make sure that the connection to the computer is done by the USB connector.

Tilt and Level Calibration

The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to connect the gimbal with the computer.

Attention : Please make sure that the connection to the computer is done by the USB connector.

Panning Speed Adjustment

The panning speed can be adjusted through the use of the configuration software. User can adjust to the desired panning speed to better adapt to his/her filming scene. There are three settings available: “SLOW”, “NORMAL” and “FAST”. Default setting is “FAST”.

Attention : Please make sure that the connection to the computer is done by the USB connector.

Initialize The Gimbal

FY WGS needs to be initialized whenever the following situations are observed after power on

1. The tilt angle is not leveled with the horizontal surface.

2. The roll angle is not parallel to the horizontal surface.

3. When the gimbal is stationary, the camera does not stay stationary.

Initialization Instructions

1. Ensure gimbal is fully assembled and camera is installed properly.

2. Place the gimbal on a flat surface and keep it stationary.

3. Power on the Gimbal.

4. Wait for the gimbal to finish its initialization before resuming the use of the gimbal.

When initialization is completed,

Note:

the LED light will quickly flash.

Motionless Flat Surface

Parameters

94.4mm

73.4mm

Vertical Tilting Angle

Rolls Angle

Horizontal Panning Angle

Tilting Increments

Panning Increments

Weight

Usage Time 3 ~ 4 Hours

320°

100°

320°

2°/S ~ 75°/S

3°/S ~ 150°/S

185.5g (Without Batteries & Camera)

93.0mm

ATTENTION

▲ Please assemble the gimbal in accordance to the diagram provided.

▲ Please upgrade the firmware and configuration settings with the provided USB data cable and USB cannector.

▲ Please charge the battery with the provided battery charger.

▲ Please install the camera securely before powering on the gimbal.

DISCLAIMER

FY WGS 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable. It is prohibited for any user to use the gimbal for any illegal purposes. Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury, death, loss, or other claim related to or resulting from the use of this product. In no event shall Guilin Feiyu Electronic Technology Co.,Ltd and our associates be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its parts. Damage resulting from use, accident, or normal wear and tear is not covered by our warranty. Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and conditions of this product at any time.