G3 Steadycam Installation Instructions
G3云台手持件安装说明书
产品安装图
Gopro3
Product Installation Diagram
请先安装好Gopro3相机后,再通电。
Attention !
Please install the Gopro3 camera
firstly ,then supply power.
M2×6
M2×25滚花手拧螺钉
M2 Knurled Thumb
×25
Screw
铰链座
Hinge Mount
M5×16滚花手拧螺钉
Knurled Thumb Screw
铰链座
Hinge Mount
M5×16滚花手拧螺钉
M5×16 Knurled thumb
screw
M2×6沉头螺钉
M2×6 Sunk Screw
M2×25滚花手拧螺钉
M2
×25 Knurled Thumb
Screw
扭开电源盖,把电池放入电池仓中。
Open power switch cap, Put batteries in holder.
电源开关
Power Switch
电池×3
Battery×3
接口和按键
Interface and buttons
+
Up
Down
-
云台4芯连接线
4 pin gimbal connection
wire
电机控制与电源接口
Motor control and power
interface
手持件可120°调节
Steadycam can be adjusted
to 120°
Down
UP
120°
G3 Steadycam Installation Instructions
G3云台手持件安装说明书
35°
45° 45°
按Down
Push Down
90°
按Up
Push Up
8°
8°
按Down
Push Down
下面几种情况需要进行陀螺仪初始化: (1) 云台启动水平角度上有偏差。 (2) 如果长时间不使用。 (3) 或者温度变化超过20度。
初始化过程如下:先把云台静止放置在桌面上,然后打开电源开关,等待云台启动。大约10 秒后云台工作,陀螺仪初始化完成。
The gyroscope need to make initialization when in following several situation : (1) When the gimbal activate the level angle have a deviation ;
(2) The gimbal has not been used for a long time; (3) There is a change in environmental temperature of over 20 degrees;
Process of gyro reset : Firstly placed the gimbal on a table and keep static ,then power on the gimbal and wait for the gimbal activate. After about 10second the
gimbal begin working , at this time the gyroscope initialization is complete.
按Up
Push Up
可以通过按钮(UP,DOWN)来调
整俯仰角。
You can adjust the pitch angle by
the button (UP,DOWN)
“UP”和”DOWN”两个按钮同时按下3秒,云台横滚电机后面的指示灯红灯常亮,进入横滚调整模式。
这时通过按钮可以调整云台的横滚角,调整完毕后,同时按下“UP”和”DOWN”两个按钮3秒,红色指示
灯熄灭,退出横滚角调整模式。
Press “UP” and “DOWN” buttons at the same time for 3 second, the indicator light at the
back of roll motor will bright red light. This will enter the roll adjustment mode. You can adjust the
roll angle by press “UP” or “DOWN” button (The adjustable range : -8° to + 8°).After finish the
adjustment ,you can press “UP” and “DOWN” buttons at the same time for 3 second, the red
indicator light will turn off then exit the roll adjustment mode.
地平面
Horizon
The angle between the roll motor and the vertical of the
横滚轴与地平面夹角不可超过45°
ground should be less than 45°
特性参数:
充电器
输入: DC 5V Min 800mA
输出: DC4.2V
为了防止火灾或受潮,
以及减少触电的危险,
请不要打开护盖。
如有零部件需维修, 请咨询授权
服务代理商。
Charger
Input:DC 5V Min 800mA
Output: DC 4.2V
WARNING:
To prevent it from fire or moisture.
To reduce the risk of electronic shock.
Do not remove cover (or back plate).
If any parts need repair, consult an
authorized service dealer.
可充电电池
型号: 16340
Rechargeable Battery
Type:16340
更多相关信息可访问飞宇科技官方网站:
www.feiyu-tech.com
Please visit the official website of
Feiyu-tech to get related information :
www.feiyu-tech.com
项目
工作电压
静止姿态跟踪精度
运动姿态跟踪精度
电机过载电流保护
电机过载保护时间
电机输出最大力矩
响应时间
俯仰角可转动角度
横滚角度可转动角度
俯仰角控制速率
重量 128g
Tech Specification:
TECH SPEC
Working Voltage
Static attitude
tracking accuracy
Motion attitude
tracking accuracy
Overload
protection
Overload
protection time
最小
7.0V
±0.01°
±0.1°
- 90°
- 45°
Min-working
voltage
7.0V
±0.01°
±0.1°
标准
12.0V
±0.2°
0°
0°
10°/S
Standard working
voltage
12.0V
±0.2°
Max-torque
response time
Controlled pitch
angle accuracy
Controlled Roll
Angle Accuracy
Pitching Angle
control rate
Weight
- 90°
- 45°
0°
0°
10°/S
128g
最大
17.0V
±0.04°
±0.5°
0.8A
600s
330us
+ 35°
+ 45°
Max-working
voltage
17.0V
±0.04°
±0.5°
0.8A
600s
330us
+ 45°
+ 45°
备注
2S~4S LIPO
电机过载600s后自动停止工
作
不含电池和相机
Remark
2S~4S LIPO
After overloaded 600s,
Gimbal will stop working
automatically.
Containing no battery &
camera