Epson SC-T7000, SC-T5000, SC-T3000 Service Manual

SERVICE MANUAL

Large Format Color Inkjet Printer

SC-T7000 series

SC-T5000 series

SC-T3000 series

Confidential

SEIJ12008

Notice:

All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.

The contents of this manual are subject to change without notice.

All efforts have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.

The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.

EPSON is a registered trademark of SEIKO EPSON CORPORATION.

General Notice:	Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
	respective owners. EPSON disclaims any and all rights in those marks.

Copyright © 2012 SEIKO EPSON CORPORATION.

COMMERCIAL PRINTER CS QUALITY ASSURANCE DEPARTMENT

Confidential

	PRECAUTIONS
Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) Damage to equipment.
DANGER	Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing
	procedures preceded by DANGER Headings.
WARNING	Signals a precaution which, if ignored, could result in damage to equipment.

The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.

DANGER

1.ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR REPAIR PROCEDURES.

2.NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK.

3.WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER SUPPLY AND OTHER ELECTRONIC COMPONENTS.

4.WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURY FROM METAL PARTS WITH SHARP EDGES.

WARNING

1.REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.

2.MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.

3.ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.

4.IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.

5.REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECONDSOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.

6.WHEN AIR DUSTER IS USED ON THE REPAIR AND THE MAINTENANCE WORK, THE USE OF THE AIR DUSTER PRODUCTS CONTAINING THE INFLAMMABLE GAS IS PROHIBITED.

7.MAKE SURE AN ANTIVIRUS SOFTWARE IS INSTALLED ON THE COMPUTER USED FOR SERVICE SUPPORT. BE SURE TO HAVE THE LATEST VIRUS DEFINITION FILE FOR THE SOFTWARE.

Confidential

About This Manual

This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.

Manual Configuration

This manual consists of six chapters and Appendix.

CHAPTER 1.PRODUCT DESCRIPTIONS

Provides a general overview and specifications of the product.

CHAPTER 2.TROUBLESHOOTING

Describes the step-by-step procedures for the troubleshooting.

CHAPTER 3.DISASSEMBLY / ASSEMBLY

Describes the step-by-step procedures for disassembling and assembling the product.

CHAPTER 4.ADJUSTMENT

Provides Epson-approved methods for adjustment.

CHAPTER 5.MAINTENANCE

Provides preventive maintenance procedures and the lists of Epson-approved lubricants and adhesives required for servicing the product.

CHAPTER 6.APPENDIX

Provides the following additional information for reference:

•Connectors

•Panel Menu Maps

•ASP List

•Exploded Diagrams

Confidential

Symbols Used in this Manual

Various symbols are used throughout this manual either to provide additional information on a specific topic or to warn of possible danger present during a procedure or an action. Be aware of all symbols when they are used, and always read NOTE, CAUTION, or WARNING messages.

Indicates an operating or maintenance procedure, practice or condition that is necessary to keep the product’s quality.

Indicates an operating or maintenance procedure, practice, or condition that, if not strictly observed, could result in damage to, or destruction of, equipment.

May indicate an operating or maintenance procedure, practice or condition that is necessary to accomplish a task efficiently. It may also provide additional information that is related to a specific subject, or comment on the results achieved through a previous action.

Indicates an operating or maintenance procedure, practice or condition that, if not strictly observed, could result in injury or loss of life.

Indicates that a particular task must be carried out according to a certain standard after disassembly and before re-assembly, otherwise the quality of the components in question may be adversely affected.

Indicates that lubrication is needed for the parts after disassembly, when doing a maintenance or replacing a part with a new one.

Lubrication

Confidential

		Revision Status
Revision	Date of Issue	Description
A	October 1, 2012	First release
		Chapter 2
		• 2.3Remedies for Service Call Error(p.43):partially deleted
B	March 6, 2013	Chapter4
		• 4.1.2Adjustment Items and the Order by Repaired Part(p.199):partially revised
		• 4.14.1Main Board initial setting(p.270):was added

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

Contents

Chapter 1 PRODUCT DESCRIPTION
1.1 Product Description ............................................................................................	11
1.2 Basic Specifications ............................................................................................	12
1.2.1 Basic Specifications ...................................................................................	12
1.2.2 Electric Specifications ...............................................................................	12
1.2.3 Ink Specifications ......................................................................................	13
1.3 Printing Specifications ........................................................................................	14
1.3.1 Paper Feed Specifications ..........................................................................	14
1.3.2 Supported Media ........................................................................................	15
1.3.2.1 Epson Special Media Table ................................................................	15
1.3.2.2 Usable Commercially Available Paper Size ......................................	18
1.3.3 Printable area .............................................................................................	20
1.3.4 Borderless Printing Specification ..............................................................	21
1.3.5 Stacker .......................................................................................................	21
1.4 Hardware Specifications .....................................................................................	22
1.4.1 Dimensions and Weight .............................................................................	22
1.4.2 Installation Room Requirement .................................................................	22
1.4.3 Part Names .................................................................................................	23
1.5 Control Panel Specifications ..............................................................................	25
1.5.1 Control panel and LCD ..............................................................................	25
1.5.2 Menu Descriptions .....................................................................................	27
1.5.3 Serviceman Mode ......................................................................................	36
Chapter 2 TROUBLE SHOOTING
2.1 Overview ............................................................................................................	40
2.1.1 Preliminary Check .....................................................................................	40
2.1.1.1 Before performing troubleshooting ....................................................	40
2.1.1.2 Check for the usage environment .......................................................	40
2.1.1.3 Recurrence check of the trouble .........................................................	40
2.1.1.4 Check for the counter values/history ..................................................	40
2.1.1.5 Test print check ..................................................................................	40
2.1.2 Troubleshooting Procedure ........................................................................	41
2.1.3 Procedure after troubleshooting .................................................................	41

	2.1.3.1 If the trouble has been successfully solved ........................................	41
	2.1.3.2 If necessary to escalate the trouble case .............................................	41
2.2	Remedies for Maintenance Requests .................................................................	42
2.3	Remedies for Service Call Error ........................................................................	43
2.4	Remedies for Print Quality Troubles ..................................................................	58
2.5	Trouble on Paper Feeding ..................................................................................	62
2.6	Other Troubles ....................................................................................................	63
2.7	Trouble on Service Program ...............................................................................	64
2.8 Trouble on NVRAM Viewer ..............................................................................		65
Chapter 3 DISASSEMBLY & ASSEMBLY
3.1	Overview ............................................................................................................	67
	3.1.1 Precautions .................................................................................................	67
	3.1.2 Cautions after assembling ..........................................................................	69
	3.1.3 Orientation Definition ................................................................................	69
	3.1.4 Recommended Tools .................................................................................	70
3.2	Parts Diagram .....................................................................................................	71
3.3	Disassembly Flowchart ......................................................................................	78
3.4	Disassembly and Assembly Procedure ...............................................................	83
	3.4.1 Preparation for servicing ...........................................................................	83
	3.4.1.1 Unlocking the CR Unit .......................................................................	83
	3.4.2 Housing ......................................................................................................	85
	3.4.2.1 TOP COVER ......................................................................................	85
	3.4.2.2 FRONT COVER ................................................................................	86
	3.4.2.3 LOWER PAPER GUIDE ...................................................................	87
	3.4.2.4 LOWER PAPER GUIDE B ...............................................................	88
	3.4.2.5 IH COVER .........................................................................................	89
	3.4.2.6 WASTE INK TANK COVER ...........................................................	92
	3.4.2.7 PRINTER COVER .............................................................................	93
	3.4.2.8 UPPER SUPPORT R COVER ...........................................................	94
	3.4.2.9 RIGHT UPPER COVER & RIGHT ROLL COVER ........................	95
	3.4.2.10 RIGHT LOWER COVER ................................................................	96

7

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

3.4.2.11 RIGHT BASE COVER ....................................................................	97
3.4.2.12 LEFT LOWER COVER ...................................................................	98
3.4.2.13 REAR RIGHT LOWER COVER ....................................................	99
3.4.2.14 UPPER LEFT COVER ..................................................................	100
3.4.2.15 LEFT UPPER COVER & LEFT ROLL COVER ..........................	101
3.4.2.16 LEFT BASE COVER .....................................................................	102
3.4.2.17 FRONT LEFT LOWER COVER ...................................................	103
3.4.2.18 REAR LEFT LOWER COVER .....................................................	104
3.4.2.19 REAR ROLL COVER FRAME .....................................................	105
3.4.2.20 CARTRIDGE COVER SENSOR ..................................................	106
3.4.2.21 R WASTE INK COVER SENSOR ................................................	107
3.4.2.22 L WASTE INK COVER SENSOR ................................................	108
3.4.2.23 INTERLOCK SWITCH .................................................................	109
3.4.3 Electric Circuit Components ....................................................................	111
3.4.3.1 MAIN BOARD ................................................................................	111
3.4.3.2 MAIN-B BOARD ............................................................................	113
3.4.3.3 MAIN-C BOARD ............................................................................	114
3.4.3.4 SUB BOARD ...................................................................................	115
3.4.3.5 SUB-B BOARD ...............................................................................	117
3.4.3.6 PSH BOARD ....................................................................................	118
3.4.3.7 PANEL BOARD ..............................................................................	120
3.4.4 Carriage Mechanism / Ink System Mechanism .......................................	122
3.4.4.1 CR COVER ......................................................................................	122
3.4.4.2 DAMPER KIT ..................................................................................	123
3.4.4.3 PRINT HEAD ..................................................................................	126
3.4.4.4 HEAD FFC .......................................................................................	127
3.4.4.5 CR FFC .............................................................................................	131
3.4.4.6 CR SCALE .......................................................................................	135
3.4.4.7 CR ENCODER .................................................................................	138
3.4.4.8 CR TIMMING BELT .......................................................................	139
3.4.4.9 CR MOTOR .....................................................................................	141
3.4.4.10 CR HP SENSOR ............................................................................	143
3.4.4.11 APG UNIT .....................................................................................	144
3.4.4.12 PG SENSOR ...................................................................................	146
3.4.4.13 PUMP CAP UNIT ..........................................................................	147
3.4.4.14 IC HOLDER ...................................................................................	148
3.4.4.15 INK TUBE .....................................................................................	152
3.4.4.16 CR UNIT ........................................................................................	156
3.4.4.17 IM SENSOR ...................................................................................	159
3.4.4.18 PW SENSOR ..................................................................................	161

3.4.5 Paper Feed Mechanism ............................................................................	163
3.4.5.1 PF MOTOR ......................................................................................	163
3.4.5.2 PF SCALE ........................................................................................	165
3.4.5.3 PF ENCODER ..................................................................................	166
3.4.5.4 PF TIMING BELT ...........................................................................	168
3.4.5.5 PRESSURE ROLLER ......................................................................	170
3.4.5.6 PRESSURE ROLLER MOTOR ......................................................	171
3.4.5.7 PRESSURE ROLLER SENSOR .....................................................	173
3.4.5.8 ATC MOTOR ..................................................................................	175
3.4.5.9 PE SENSOR (ROLL PAPER) .........................................................	177
3.4.5.10 PE SENSOR (THICK PAPER) ......................................................	178
3.4.5.11 PAPER THICKNESS SENSOR ....................................................	180
3.4.6 Cutter Mechanism ....................................................................................	181
3.4.6.1 CUTTER UNIT ................................................................................	181
3.4.7 Fans ..........................................................................................................	183
3.4.7.1 BOARD BOX FAN .........................................................................	183
3.4.7.2 SUCTION FAN ................................................................................	184
3.4.8 Auto Take-up Reel ...................................................................................	185
3.4.8.1 TAKE-UP REEL COVER ...............................................................	185
3.4.8.2 TAKE-UP REEL SENSOR .............................................................	186
3.4.8.3 TAKE-UP REEL LED .....................................................................	187
3.4.8.4 TAKE-UP REEL SWITCH .............................................................	188
3.4.8.5 TAKE-UP REEL PS BOARD .........................................................	190
3.4.8.6 TAKE-UP REEL MOTOR ..............................................................	192
3.4.8.7 TAKE-UP REEL MAIN BOARD ...................................................	194
Chapter 4 ADJUSTMENT
4.1 Overview ..........................................................................................................	198
4.1.1 Precautions ...............................................................................................	198
4.1.2 Adjustment Items and the Order by Repaired Part ..................................	199
4.1.3 Adjustment Items .....................................................................................	211
4.1.4 List of Tools/Software/Consumables for Adjustments ...........................	219
4.1.5 Service Program Basic Operations ..........................................................	220
4.2 NV-RAM BACKUP/NVRAM Viewer ............................................................	221
4.2.1 NVRAM Read Procedure ........................................................................	221
4.2.2 NVRAM Write Procedure .......................................................................	221
4.2.3 NVRAM Viewer Basic Operation ...........................................................	222
4.3 ADJUSTMENTS (Individual) .........................................................................	227
4.4 ADJUSTMENTS (Sequence) ...........................................................................	228
	8

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

4.5 Installing Firmware ..........................................................................................	229
4.6 Image Print .......................................................................................................	230
4.7 Counter Reset ...................................................................................................	231
4.8 References ........................................................................................................	232
4.9 Initial Ink Charge Flag ......................................................................................	233
4.10 CR Related Adjustments ................................................................................	234
4.10.1 CR Belt Tension Check .........................................................................	234
4.10.2 APG Function Check .............................................................................	237
4.10.3 Ink Mark Sensor Check & Auto Adjustment ........................................	238
4.10.4 CR Scale Check .....................................................................................	239
4.10.5 CR Active Damper Auto Adjustment ....................................................	240
4.10.6 Auto Uni-D Adjustment ........................................................................	241
4.10.7 Auto Bi-D Adjustment, acceleration/deceleration print correction .......	242
4.10.8 PW + T&B&S check and adjustment ....................................................	243
4.10.8.1 PW Adjustment ..............................................................................	243
4.10.8.2 T&B&S Adjustment .......................................................................	243
4.10.9 PG Adjustment .......................................................................................	245
4.11 Head Related Checks and Adjustments ..........................................................	248
4.11.1 Tube Inner Pressure Reduction ..............................................................	248
4.11.2 Head ID Input ........................................................................................	249
4.11.3 Nozzle Check .........................................................................................	251
4.11.4 Cleaning .................................................................................................	252
4.11.5 Head Inclination Adjustment (CR direction) .........................................	253
4.11.5.1 Head Inclination Auto Adjustment (CR direction) ........................	253
4.11.5.2 Head Inclination Manual Adjustment (CR direction) ....................	254
4.11.5.3 Correcting Head Inclination (CR direction) ...................................	254
4.11.6 Head Slant Adjustment (PF direction) ...................................................	256
4.11.6.1 Head Slant Auto Adjustment (PF direction) ..................................	256
4.11.6.2 Head Slant Manual Adjustment (PF direction) ..............................	257
4.11.6.3 Correcting Head Slant (PF direction) .............................................	258
4.12 Ink Supply Related Checks and Adjustments ................................................	259
4.12.1 Ink eject .................................................................................................	259
4.12.2 Cleaning (Tube Inner Cleaning) ............................................................	260
4.12.3 Initial Ink Charge ...................................................................................	261
4.13 Media Feed Related Checks and Adjustments ...............................................	262
4.13.1 PF Belt Tension Check ..........................................................................	262
4.13.2 PC Scale Check ......................................................................................	264
4.13.3 Media Feed Auto Adjustment ................................................................	265

	4.13.4 Cut Position Check & Adjustment ........................................................	266
	4.13.5 Paper Thickness Sensor Adjustment .....................................................	267
	4.13.6 Rear AD Adjustment .............................................................................	269
4.14 Boards Related Checks and Adjustments .......................................................		270
	4.14.1 Main Board initial setting ......................................................................	270
	4.14.2 RTC & USB ID Input ............................................................................	271
	4.14.3 MAC Address Input ...............................................................................	272
	4.14.4 Serial Number Input ..............................................................................	273
	4.14.5 HDD S/N Information Writing ..............................................................	274
	4.14.6 Board Replacement Date & Time Setting .............................................	275
4.15 Other Printer Checks and Adjustments ..........................................................		276
	4.15.1 Suction Fan Adjustment ........................................................................	276
	4.15.2 Panel Setting Reset & Job History Reset ...............................................	277
	4.15.3 Operation Panel Check (LCD & Buttons) .............................................	278
	4.15.3.1 Panel LCD Operation Check ..........................................................	278
	4.15.3.2 Panel Buttons Operation Check .....................................................	278
	4.15.4 Motor Measurement & Automatic Adjustment .....................................	279
Chapter 5 MAINTENANCE
5.1	Overview ..........................................................................................................	281
5.2	Storing the Printer ............................................................................................	282
5.3	Transportation ..................................................................................................	283
5.4	Exchange Parts .................................................................................................	284
5.5	Cleaning ............................................................................................................	285
5.6	Lubrication .......................................................................................................	287
Chapter 6 APPENDIX
6.1	Block Wiring Diagram .....................................................................................	291
	6.1.1 Main Body ...............................................................................................	291
	6.1.2 Auto Take-up Reel ...................................................................................	292
6.2	Connection Diagram .........................................................................................	293
6.3	Panel Menu Map ..............................................................................................	309
6.4	Part names used in this manual ........................................................................	312
6.5	Exploded Diagram/Parts List ...........................................................................	314

9

Confidential

C H A P T E R

1

PRODUCT DESCRIPTION

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.1 Product Description

Models

SC-T7000 series: 1118 mm (44 inch); supports Super B0

SC-T5000 series: 914 mm (36 inch); supports Super A0

SC-T3000 series: 620 mm (24 inch); supports Super A1

Supported paper thickness Up to 1.5 mm

Ink configuration

Brand-new water color pigment ink configuration with excellent black tone important in quality CAD line drawing and highly vivid red essential for commercial posters

Ink configuration: Cyan, Yellow, Magenta, Matte black, Photo black

High-speed throughput

Prints A1 plain paper in 28sec.

High print quality

For posters:

Excellent print quality in 4 colors, with resolution of up to 2800x1440 dpi, and in variable dot sizes (minimal 3.5 picoliter)

For CAD:

High quality CAD line drawing achieved by optimizing the combination of new inks and print modes

Media handling

Easier paper loading available thanks to the design for front-access and spindle-less with optimal height based on ergonomics

Supports continuous printing of drawings or posters (in a standard size such as A0, A1 or US-ANSI D/E)

Translucent printer cover allows you to check which roll paper is loaded easily

Space saving design

Front access design allows you to set the printer near a wall because you can exchange the media, ink cartridges, maintenance box, and cutter from the front.

New driver and applications

Brand-new driver with simple UI

With the web UI OS-independent configuration and control of HDD through the Web are available.

Provides the job monitoring and management functions using a job monitoring tool.

Easy printing from Microsoft Office using dedicated plug-in software

Improved shorter occupancy time of the host PC

Occupancy time of the host PC has been significantly shortened with ESC/ Page and HP-GL2/RTL.

By adding the optional HDD unit, PC-less re-printing and more shortened occupancy time become available.

Lower running cost

Independent ink cartridges for each color

high-capacity (700ml/350ml/150ml) ink cartridges

PC-less enlarged photocopy

Simply connecting a scanner enables PC-less enlarged photocopy.

Large sized LEDs

Equipped with large-sized LEDs for easier recognition of the printer’s error status

PRODUCT DESCRIPTION

Product Description

11

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.2

Basic Specifications

1.2.1

Basic Specifications

Item

Specification

Print method

On-demand inkjet

Black

360 nozzles x 2 lines x 2 colors (Photo

Configuratio

Black, Matte Black)

n of nozzles

Color

360 nozzles x 2 lines x 3 colors

(Yellow, Magenta, Cyan)

Maximum resolution

2,880 x 1,440dpi

ESC/P Raster (commands are

Control code

nondisclosure)

HP-GL/2, HP-RTL

Paper feed method

Friction

RAM

For Main

512 MB

For Network

128 MB

Interface

High-Speed USB

Ethernet (10Base-T/100Base-TX/

1000Base-T)

Main body operation environment

10°C to 35 °C

-20 °C to 60 °C

Temperature

When storing (packed)

(within 120 hours under 60 °C, and

within 1 month under 40 °C)

When storing (unpacked)

-20 °C to 40 °C

(within 1 month under 40 °C)

Main body operation environment

20% to 80% (Non condensing)

Humidity

When storing (packed)

5% to 85% (Non condensing)

When storing (unpacked)

5% to 85% (Non condensing)

*Nozzle set configuration is;

Row A

Row B

Row C

Row D

Row E

Row F

Row G

Row H

Row I

Row J

C

M

Y

PK

MK

MK

PK

Y

M

C

1.2.2 Electric Specifications

			Item		Specification
				SC-T7000 series	SC-T5000 series	SC-T3000 series
	Rated voltage				100 to 240 VAC
	Input voltage range				90 to 264 VAC
	Rated current			1.0 A to 0.5 A	0.9 A to 0.5 A	0.8 A to 0.4 A
	Rated frequency				50 to 60 Hz
	Input frequency range				49.5 to 60.5 Hz
	Power		Operating	Approx. 72 W	Approx. 65 W	Approx. 54 W
			Sleep mode		3.0 W or less
	consumption
			Power OFF		0.4 W or less
	Insulation resistance			10 MΩ or more (between AC line and chassis at 500 VDC)
	Dielectric strength			1.0 kV rms AC for 1 min. or 1.2 kV rms AC for 1 sec.
				(between AC line and chassis)
	Leek current				0.25 mA or less
				Conforms to International Energy Star Program
	Compliance with regulations			(Category: the harmonic restraint measure guideline)
				Conforms to VCCI Class B (with full options installed)

PRODUCT DESCRIPTION

Basic Specifications

12

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B

1.2.3 Ink Specifications

Item	Specification
Form	Exclusive ink cartridge
Pigment ink	Black system: Photo Black, Matte Black
colors	Color system: Yellow, Magenta, Cyan
Cartridge life	See the date printed on the package (at normal temperature)
Guaranteed life
after	1 year (after mounted in the printer)
installation
	Uninstalled (packed): -20 to 40 °C
	(within 4 days under -20 °C, and within 1 month under 40 °C)
Storage	Installed: -20 to 40 °C
	(within 4 days under -20 °C, and within 1 month under 40 °C)
	Transporting (packed): -20 to 60 °C
	(within 4 days under -20 °C, within 1 month under 40 °C, and within 72
	hours under 60 °C)
Capacity	700 ml/350 ml/110ml
Dimensions	700ml: W40 x L305 x H110 mm
	350ml: W40 x L200 x H110 mm
	110ml: W25 x L200 x H110 mm

PRODUCT DESCRIPTION

Basic Specifications

13

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B

	1.3	Printing Specifications
	1.3.1	Paper Feed Specifications
		Item	Specification
	Paper feed method		Friction feed
	Return pitch		2.2049 μm (1/11,520 inch)
	Paper feeder		Roll paper manual feed
			Cut sheet manual feed
	Feed speed		300ms/ (1/6 inch)

PRODUCT DESCRIPTION

Printing Specifications

14

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.3.2 Supported Media

1.3.2.1 Epson Special Media Table

ROLL PAPER

Note "*1":

SC-T3000 Series not supported

"*5":

When a scanner is connected

"*2":

SC-T3000 Series/SC-T5000 Series not supported

"*6": U: Borderless printing available, but borders may appear or print quality decline due to paper

"*3":

When the optional auto take-up reel unit is used (SC-T7000 series)

expanding or contracting.

"*4": Use the tensioner supplied with the auto take-up reel unit.

Size

Thickness

Core

Borderless

Take-up*3

Head

Name

Diameter

Enlarged*5

ICC Profile

(mm)

(inch)

Print*6

Alignment

mm

inch

Forward

Backward

406

16

EPSON SC-

610

24

√

√

√

√

√

Premium Glossy Photo Paper (250)

0.27

3

T3000_5000_7000_Series Premium

914*1

36*1

Glossy Photo Paper 250.icc

1118*2

44*2

406

16

EPSON SC-

610

24

√

√

√

√

√

Premium Semigloss Photo Paper (250)

0.27

3

T3000_5000_7000_Series Premium

914*1

36*1

Semigloss Photo Paper 250.icc

1118*2

44*2

254

10

√

-

-

300

11.8

406

16

√

√

EPSON SC-

Premium Luster Photo Paper (260)

508

20

0.27

3

-

T3000_5000_7000_Series Premium

√

√

Luster Photo Paper 260.icc

610

24

√

914*1

36*1

1118*2

44*2

406

16

EPSON SC-

610

24

√

√

√

√

√

Premium Semimatte Photo Paper (260)

0.27

3

T3000_5000_7000_Series Premium

914*1

36*1

Semimatte Photo Paper 260.icc

1118*2

44*2

432

17

EPSON SC-

610

24

√

√

√

√

√

Photo Paper Gloss 250

0.25

3

T3000_5000_7000_Series Photo

914*1

36*1

Paper Gloss 250.icc

1118*2

44*2

PRODUCT DESCRIPTION

Printing Specifications

15

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

Size

Thickness

Core

Borderless

Take-up*3

Head

Name

Diameter

Enlarged*5

ICC Profile

mm

inch

(mm)

(inch)

Print*6

Forward

Backward

Alignment

420 (A2)

---

-

EPSON SC-

610

24

√

√

√

√

Premium Glossy Photo Paper (170)

0.18

2

√

T3000_5000_7000_Series Premium

914*1

36*1

Glossy Photo Paper 170.icc

1118*2

44*2

420 (A2)

---

-

EPSON SC-

610

24

√

√

√

√

Premium Semigloss Photo Paper (170)

0.18

2

√

T3000_5000_7000_Series Premium

914*1

36*1

Semigloss Photo Paper 170.icc

1118*2

44*2

610

24

U

√

√

EPSON SC-

Enhanced Synthetic Paper

0.13

2

-

-

T3000_5000_7000_Series Enhanced

1118*2

44*2

Synthetic Paper.icc

610

24

U

√

√

EPSON SC-

Enhanced Adhesive Synthetic Paper

0.18

2

-

-

T3000_5000_7000_Series Enhanced

1118*2

44*2

Adhesive Synthetic Paper.icc

610

24

√

√*4

√

√

EPSON SC-

Doubleweight Matte Paper

914*1

36*1

0.21

2

-

T3000_5000_7000_Series

Doubleweight Matte Paper.icc

1118*2

44*2

432

17

EPSON SC-

610

24

U

√

√

Enhanced Matte Paper

0.25

3

-

-

T3000_5000_7000_Series Enhanced

914

36

and Archival Matte Paper.icc

1118

44

432

17

EPSON SC-

610

24

√

√*4

√

√

Singleweight Matte Paper

0.15

2

-

T3000_5000_7000_Series

914*1

36*1

Singleweight Matte Paper.icc

1118*2

44*2

PRODUCT DESCRIPTION

Printing Specifications

16

Confidential

	SC-T7000 series/SC-T5000 series/SC-T3000 series								Revision B
	CUT SHEET
	Note "*1": SC-T3000 Series not supported
	"*2": When a scanner is connected
	"*3": U: Borderless printing available, but borders may appear or print quality decline due to paper expanding or contracting.
	Name		Size	Thickness	Borderless*3	Enlarged*2	Head Alignment		ICC Profile
				(mm)
			Super A3/B		U
	Premium Glossy Photo Paper			0.27		√	√		EPSON SC-T3000_5000_7000_Series Premium Glossy Photo Paper.icc
			A2		-
			US-C		U
			Super A3/B		U
	Premium Semigloss Photo Paper			0.27		√	√		EPSON SC-T3000_5000_7000_Series Premium Semigloss Photo Paper.icc
			A2		-
			US-C		U
			Super B		U
	Premium Luster Photo Paper			0.27		√	√		EPSON SC-T3000_5000_7000_Series Premium Luster Photo Paper.icc
			A2		-
			US-C		U
	Archival Matte Paper/Enhanced Matte		Super A3/B		U				EPSON SC-T3000_5000_7000_Series Enhanced and Archival Matte
							√
			A2	0.26	-	-
	Paper								Paper.icc
			US-C		U
			Super A3/B		U
	Photo Quality Inkjet Paper			0.12		-	√		EPSON SC-T3000_5000_7000_Series Photo Quality Ink Jet Paper.icc
			A2		-
			US-C		U
			610 x 762 mm
	Enhanced Matte Posterboard		(24" x 30")	1.30	-	-	-		EPSON SC-T3000_5000_7000_Series Enhanced Matte Poster Board.icc
			762 x 1016 mm
			(30" x 40")*1

PRODUCT DESCRIPTION

Printing Specifications

17

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.3.2.2 Usable Commercially Available Paper Size

This printer supports the following paper specifications for non-Epson media.

CAUTION	Do not use paper that is wrinkled, scuffed, torn, or dirty.
	Although plain paper and recycled paper manufactured by
	other companies can be loaded and fed in the printer as long as
	they meet the following specifications, Epson cannot guarantee
	the print quality.
	Although other paper types manufactured by other companies
	can be loaded in the printer as long as they meet the following
	specifications, Epson cannot guarantee the paper feeding and
	print quality.

ROLL PAPER

	Item	Specification
	Media types	Plain paper and recycled paper
	Paper core size	2 inch and 3 inch
	Roll paper outer	150 mm or less
	diameter
	Width	SC-T7000 Series: 254 mm (10 inches) to 1,118 mm (44 inches)
		SC-T5000 Series: 254 mm (10 inches) to 914 mm (36 inches)
		SC-T3000 Series: 254 mm (10 inches) to 610 mm (24 inches)
	Paper thickness	0.08 to 0.5 mm
	Basis weight	64 to 90g/m2
		254 mm/10 inch
		300 mm/11.8 inch
		Super A3/B/329 mm
		406 mm/16 inch
		17 inch
	Available width for	B2/515mm
		A1/594mm
	borderless printing
		610 mm/24 inch
		728 mm
		A0/841 mm
		914 mm/36 inch
		1030 mm
		1118 mm/44 inch

PRODUCT DESCRIPTION

Printing Specifications

18

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series		Revision B
CUT SHEET
Item	Specification
Media types	Plain paper and recycled paper
Width	SC-T7000 Series: 210 mm (A4) to 1,118 mm (44 inches)
	SC-T5000 Series: 210 mm (A4) to 914 mm (36 inches)
	SC-T3000 Series: 210 mm (A4) to 610 mm (24 inches)
Length	279.4 to 1,580 mm
Paper thickness	0.08 to 0.8 mm
	254 mm/10 inch
	300 mm/11.8 inch
	Super A3/B/329 mm
	406 mm/16 inch
	17 inch
Available width for	B2/515 mm
	A1/594 mm
borderless printing
	610 mm/24 inch
	728 mm
	A0/841 mm
	914 mm/36 inch
	1030 mm
	1118 mm/44 inch

PRODUCT DESCRIPTION

Printing Specifications

19

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.3.3 Printable area

ROLL PAPER

Note "*1": SC-T7000 Series "*2": SC-T5000 Series "*3": SC-T3000 Series

"*4": If “Banner” is selected for “Roll Paper Option” in the printer driver “Advanced” tab, the top and bottom margins are 0 mm.

254mm~1118mm

254mm~914mm

3mm/15mm

254mm~620mm

0mm/3mm

C

3mm/15mm

127mm
~
15m B				D

A		3~45mm

Table 1-1. Roll Paper Margin

	Roll Paper Margin Parameter	Margin Values
	Normal	A, C = 15mm*
		B, D = 3mm
	Top15mm/Bottom15mm	A, C = 15mm
		B, D = 3mm
		A = 35mm
	Top35mm/Bottom15mm	C =15mm
		B, D =3mm

Table 1-1. Roll Paper Margin

Roll Paper Margin Parameter	Margin Values
	A = 45mm
Top45mm/Bottom15mm	C =15mm
	B, D = 3mm
3mm	A, B, C, D = 3mm
15mm	A, B, C, D = 15mm

When “Normal” is selected, the value for A is 20 mm for the following paper.

Premium Glossy Photo Paper (250) / Premium Semigloss Photo Paper (250) / Premium Luster Photo Paper (260) / Premium Semimatte Photo Paper (260)

When the following media are used in the “CAD / Line Drawing” mode, the value for A and C is 3 mm.

Singleweight Matte Paper

CUT SHEET

PRODUCT DESCRIPTION

Printing Specifications

20

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.3.4 Borderless Printing Specification

AVAILABLE PAPER TYPE

For the paper types and sizes that support the borderless printing, see "1.3.2.1 Epson Special Media Table" (p15).

ROLL PAPER CUTTING OPERATION

	Printer driver	Cutting Operation	Explanation
	settings

	A
Borderless	The default printer driver setting is “Borderless”.

B

The top area may become slightly uneven depending on the image since the print

		operation stops while cutting the top edge of
		the roll paper.
		If the cut position is misaligned slightly, small
	A
		parts of the image may be shown on the top or
Single Cut		bottom of the adjacent pages. If this occurs,
		perform “Adjust Cut Position”.
	B	When printing only one page the operation
		performed is the same as that for “Double Cut”.
		When continuously printing multiple sheets,
		the printer cuts 1 mm inside on the top edge of
		the first page and the bottom edge of the
		subsequent pages to avoid showing margins.

	Printer driver	Cutting Operation	Explanation
	settings

The top area may become slightly uneven depending on the image since the print

		operation stops while cutting the top edge of
		the roll paper.
	A	The printed paper is approximately 2 mm
Double Cut		shorter than the specified size since the printer
		cuts the paper inside the image to avoid
		showing top and bottom margins.
	B
		After cutting the bottom edge of the previous
		page, the printer feeds the paper, and then cuts
		the top edge of the following page. Although
		this produces 60 to 127 mm cut-off pieces, the
		cut is more accurate.

1.3.5 Stacker

Table 1-2. Continuous Stacker

					Stackable Pages
		Paper size	Paper Type	SC-T3000	SC-T5000	SC-T7000
				Series	Series	Series
	A1	594 x 841mm	Plain paper	20 pages	20 pages	20 pages
	A0	841 x 1,189mm		---	20 pages	20 pages

Table 1-3. Single Sheet Stacker

Maximum Length

SC-T3000 Series	SC-T5000 Series	SC-T7000 Series
Approx. 1,292 mm	Approx. 1,292 mm	Approx. 1,575 mm

PRODUCT DESCRIPTION

Printing Specifications

21

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.4 Hardware Specifications

This section provides the printer dimensions and shows the main components.

1.4.1 Dimensions and Weight

	Model	Width	Depth*1	Height	Weight*2
	SC-T7000 Series	1,608 mm	813 mm	1,128 mm	Approx. 82 kg
	SC-T5000 Series	1,405 mm	813 mm	1,128 mm	Approx. 75 kg
	SC-T3000 Series	1,050 mm	691 mm	613 mm	Approx. 51 kg
	(w/o dedicated stand)
	SC-T3000 Series	1,050 mm	813 mm	1,128 mm	Approx. 61 kg
	(w/ dedicated stand)
	Note 1: When the paper basket is retracted
	2: Excluding ink cartridges

1.4.2 Installation Room Requirement

Figure 1-1. SC-T7000 Series/SC-T5000 Series

Figure 1-2. SC-T3000 Series

PRODUCT DESCRIPTION

Hardware Specifications

22

Confidential

	SC-T7000 series/SC-T5000 series/SC-T3000 series		Revision B
	1.4.3 Part Names		Table 1-4. Front Side
	FRONT SIDE	No.	Name
		1	Printer cover
		2	Poster board support
		3	Maintenance box covers
		4	Paper basket
		5	Casters
		6	Stack guides
		7	Stack guide switch lever
		8	Cartridge cover
		9	Ink cartridges
		10	AC inlet
		11	Option port
		12	LAN port
		13	Data light
		14	Status light
		15	USB port
		16	Control panel
		17	Alert lamp
		18	Roll rest
		19	Adapter guides
		20	Roll lock lever
		21	Adapter holder
		22	Paper slot
	Figure 1-3. Front Side	23	Print head
		24	Roll paper cover
		25	Paper eject guide

PRODUCT DESCRIPTION

Hardware Specifications

23

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

ROLL PAPER ADAPTER

Figure 1-4. Roll paper adapter

Table 1-5. Roll paper adapter

No.	Name

1Adapter lock lever

2Size lever

PRODUCT DESCRIPTION

Hardware Specifications

24

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

1.5 Control Panel Specifications

1.5.1 Control panel and LCD

CONTROL PANEL

Figure 1-5. Control panel

		Table 1-6. Control panel
		Name	Function
	1	Power button	Turns the power on and off.
			On: The power is on.
	2	Power light	Flashing: The printer is receiving data or cleaning the
			print head or performing other operations in
			the course of being shut down.
			Off: The power is off.
	3	Load/Remove Paper button	Displays the Load/Remove Paper menu.
	4	Screen	Displays the printer’s status, menus, error messages, and
			so on.
	5	[Menu] button	Displays the menu for the tab currently selected in the
			display.
	6	Back button	If menus are displayed, pressing this button takes you up
			one level in the menu hierarchy.
	7	Left/Right buttons	Use these buttons to select tabs.
	8	Up/Down buttons	When menus are displayed, these buttons can be used to
			highlight items or options.
			Displays the menu for the tab currently selected in the
			display.
	9	OK button	When menus are displayed and an item is highlighted,
			pressing this button displays the sub-menu for the
			highlighted item.
			If pressed while a parameter is selected from the Menu,
			the parameter is set or executed.
	10	Help button	Displays the Help menu.
	11	Maintenance button	Displays the Maintenance menu, which is used for nozzle
			checks and head cleaning.
			The printer enters pause status if this is pressed while
	12	Pause/Cancel button	printing.
			Pressing this button while a menu or help is displayed
			closes the menu or help and returns the printer to ready
			status.
			It is used to manually cut roll paper using the built-in
	13	Feed/Cut Media button	cutter.
			If printing is not currently in progress and the printer is
			loaded with roll paper, you can feed paper ahead by
			pressing first this button and then the [T] button.

PRODUCT DESCRIPTION

Control Panel Specifications

25

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series

Revision B

LCD

Screen View

			Figure 1-6. LCD
			Table 1-7. LCD
		Name	Function
	1	Message	Displays the printer’s status, operation, and error
			messages.

			: An error occurred.
			: Non-genuine cartridge is installed.
			Shows the status of the Maintenance Box and is used to
			display the Maintenance menu.
			Maintenance Box status is shown as follows.
		Maintenance	: No error.
		Tab	: The Maintenance Box is nearing the end of
			its service life.
			: Maintenance Box is at the end of its service
			life.
		Setup Tab	Displays the IP address and menus for various settings.
		Enlarged	Displayed only when a scanner is connected.
		Copy Tab
			Table 1-7. LCD
	Name		Function
		Print	Displays print job status and can be used to access the
		Queues Tab	Print Queues menu.
		Paper Tab	Shows the type of paper in the printer and can be used to
			access the Paper menu.
			Displays ink status.
			The ink cartridge status is indicated as follows.
			: No error.
			: Ink is low.
		Ink Tab	: Ink cartridge is expended.
2	Tabs/Info
	Display Area

PRODUCT DESCRIPTION

Control Panel Specifications

26

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B

1.5.2 Menu Descriptions

Note "*1": Displayed only when optional hard disk unit is installed.

			Table 1-8. Menu List
Menu	Menu Item / Setting Value (Shaded one is the default)				Explanation
					Lists the estimated start time and time needed to print the selected job.
				Waiting Job Name	It also predicts whether the job can be completed without replacing paper, ink or the
					Maintenance Box. Printing can proceed even if “Can Not Complete” is displayed.
				User
					However, the printer may run out of ink or paper during printing.
				Estimated Start
		XXXXXXXXXXX			Remote Manager and the LFP HDD Utility display the reason for the “Can Not
	Print Queue*1			Time
					Complete” message and allow you to hold or cancel the job.
		(name of queued print job)		Estimated Print
					The printer will only predict availability on the basis of the amount of paper
				Time
					remaining if “On” is selected for “Roll Paper Remaining”.
				Printing
					The printer will not predict availability on the basis of the amount of ink remaining
				Availability
					when documents are printed using LFP Print Plug-In for Office or EPSON
					CopyFactory5.
				Paused Job Name	This option is available only if “On” is selected for “Store Held Job” in the Setup
					menu.
			XXXXXXXXXXX	User	Displays the print settings for held jobs and the reason the job is held.
				Paper Type	Jobs that are held because the job print settings differ from those currently selected
		View Hold Queue	(name of held print
	Hold Queue*1			Source	for the printer can be printed as described below.
Print Queues menu			job)
				Size	1. Replace the paper and take whatever other steps may be necessary to ready the
				Reason For Hold	device for printing.
					2. Select “Resume All Jobs”.
		Resume All Jobs		Press the [OK] button to resume all held jobs currently in the queue.
				Stored Job Name
				User
				Length
				Pages	Shows the status of the selected stored job when it was last printed.
	Saved Job Queue*1	XXXXXXXXXXX (name of stored print		Paper Type	After viewing the job, press the [OK] button to enter the number of copies. Press the
		job)		Copies	[S]/[T] buttons to choose the number of copies and press the [OK] button to display
				Source	the estimated print time and print availability. Press the [OK] button to start printing.
				Size
				Estimated Print
				Time
	Print Job Log Sheet			Press the [OK] button to print the print job log.

PRODUCT DESCRIPTION

Control Panel Specifications

27

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series						Revision B
				Table 1-8. Menu List
Menu	Menu Item / Setting Value (Shaded one is the default)					Explanation
						Press the [OK] button to view instructions for removing the paper. Follow the on-
					Remove Paper	screen instructions to remove the paper.
						Instructions are not displayed if no paper is loaded.
	Load/Remove Paper				Roll Paper	Highlight the paper to be loaded and press the [OK] button. Follow the on-screen
					Cut Sheet (up to 0.8	instructions to load the paper.
					mm thick)	If paper is already loaded in the printer, the instructions for removing the loaded
						paper type will be displayed before loading instructions are shown.
					Poster Board
		Photo Paper
		Matte Paper			Select the type of paper loaded.
	Select Paper Type
		Plain Paper
		Others
Paper menu		Custom Paper			Select the name of the custom paper loaded in the printer.
					Photo Paper
			Select Reference		Matte Paper	You can select the media type that is the closest to the paper you are using.
					Plain Paper
			Paper
					Others
	Custom Paper	XXXXXXXXXXX			No Paper Selected	Select this option if you do not wish to specify the paper type.
		(name of custom			Narrow
	Setting					Select the platen gap which is the distance between the print head and the paper.
		paper type)
					Standard
			Platen Gap			Normally, select “Standard”. Select a wider setting if printed images are smeared. If,
					Wide	upon performing head alignment you feel that it is still not completely aligned, select
						“Narrow”.
					Wider
			Detect Paper		Press the [OK] button to print a pattern to determine the thickness of the current paper.
			Thickness		Select the pattern number with the least misalignment from the print results.

PRODUCT DESCRIPTION

Control Panel Specifications

28

Confidential

	SC-T7000 series/SC-T5000 series/SC-T3000 series		Revision B
			Table 1-8. Menu List
	Menu	Menu Item / Setting Value (Shaded one is the default)	Explanation

	Paper menu	Custom Paper
		Setting

Pattern	Use this setting if you are unable to resolve banding issues (horizontal striped lines or
	uneven colors) in the standard print area (for cut sheets, the area excluding the 1 to 2
	cm strip at the bottom of the paper) even after head cleaning or head alignment.
	When “Pattern” is selected;
	Press the [OK] button to print an adjustment pattern. Measure the distances between
	the “+” symbols in the printed adjustment pattern. Use only the distance between the
	center symbols or the average of the distances between the left, center, and right
	symbols.

Paper Feed Adjust

Value

XXXXXXXXXXX (name of custom paper type)

			After the adjustment pattern is printing, the length of the pattern will be displayed in
			the control panel. Press the [S]/[T] buttons to enter the measured value and press
			the [OK] button.
			When “Value” is selected;
			Choose an adjustment between -0.70 and +0.70%. Selecting too small a value causes
			dark bands; adjust the amount upward. Similarly, choosing too large a value causes
			white bands; adjust the amount downward.
			It is important to choose the appropriate amount of suction for the paper used in order
			to maintain the correct distance between the paper and the print head. Choosing too
	Paper Suction	-4 to 0	high a value for thin or soft paper will increase the distance between the paper and the
			print head, causing print quality to decline or preventing the paper feeding correctly.
			If this happens, lower the paper suction. The suction power is weakened when the
			parameter is lowered.
		Normal
	Roll Paper Tension	High	Select “High” or “Extra High” if the paper wrinkles during printing.
		Extra High

PRODUCT DESCRIPTION

Control Panel Specifications

29

Confidential

SC-T7000 series/SC-T5000 series/SC-T3000 series						Revision B
				Table 1-8. Menu List
Menu	Menu Item / Setting Value (Shaded one is the default)					Explanation
			Remove Skew		On	Select whether to enable (“On”) or disable (“Off”) paper skew reduction.
		XXXXXXXXXXX			Off
	Custom Paper
			Setting Name		Enter a name of up to 22 characters for custom paper settings. Choose an easy-to-remember name for quick
		(name of custom
Paper menu	Setting				selection.
		paper type)
			Restore Settings		Yes	Restore the selected custom paper settings to default values.
					No
	Print Paper List				Press the [OK] button to print a list of custom paper settings.
	Nozzle Check				Press the [OK] button to print a nozzle check pattern. Visually inspect the printed pattern and perform head
					cleaning if you notice faint or missing areas.
	Head Cleaning				Inspect the printed pattern and select the check boxes for patterns with faint or missing areas. To select all
					nozzles, place a check in the box on the left.
		Auto(Uni-D)			If print results are grainy or out of focus, perform head alignment to realign the print head. If “Auto” is
		Auto(Bi-D)
Maintenance menu	Head Alignment				selected, the printer will scan the printed pattern during printing and realign the head automatically.
					If “Manual” is selected, a pattern will be printed; inspect the pattern visually and enter the value you think
		Manual(Uni-D)
					appropriate.
		Manual(Bi-D)
		Adjust Cut Position			-3 to 3 mm	You can fine tune the cut position when printing to roll paper with no margins in all
						directions. The cut position can be adjusted in increments of 0.2 mm.
	Cutter Maintenance
		Replace Cutter			Moves the cutter to the replacement position so it can be replaced. Press the [OK] button to move the cutter
					to the replacement position. The paper must be removed before replacing the cutter.
					On	Choose “On” to automatically cut roll paper using the built-in cutter as each page is
			Auto Cut			printed, “Off” to disable auto paper cutting. The setting selected with the printer
					Off
						driver takes priority when the printer driver is used.
					On	If “On” is selected during borderless printing, the printer will automatically trim the
			Refresh Margin			leading edge to remove any ink stains that may have been left by the previous copy;
					Off
						to disable this feature, choose “Off”.
Setup menu	Printer Setup	Roll Paper Setup			On	If “Auto Cut” is “Off”, you can choose to print (“On”) or not print (“Off”) cut lines
						on roll paper. Cut lines are not printed if “Auto Cut” is “On” or when cut sheets or
						poster board is used.
			Page Line			Note, however, that if the roll width selected with the computer is narrower than the
					Off	paper loaded in the printer, cut lines will be printed regardless of the option selected
						for “Auto Cut”.
						The setting selected with the printer driver takes priority when the printer driver is
						used.
PRODUCT DESCRIPTION			Control Panel Specifications				30

Confidential