SERVICE MANUAL
Color Inkjet Printer
L365/L366, L360/L362/L363
L310/L312/L313,L220/L222, L130/L132
CONFIDENTIAL
SEMF14-013
Notice:
All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
The contents of this manual are subject to change without notice.
The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
Note :Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright ♥ 2015 SEIKO EPSON CORPORATION
Printer CS Quality Assurance Department
Confidential
Safety Precautions
All safety procedures described here shall be strictly adhered to by all parties servicing and maintaining this product.
DANGER
Strictly observe the following cautions. Failure to comply could result in serious bodily injury or loss of life.
1.Always disconnect the product from the power source and peripheral devices when servicing the product or performing maintenance.
2.When performing works described in this manual, do not connect to a power source until instructed to do so. Connecting to a power source causes high voltage in the power supply unit and some electronic components even if the product power switch is off. If you need to perform the work with the power cable connected to a power source, use extreme caution to avoid electrical shock.
WARNING
Strictly observe the following cautions. Failure to comply may lead to personal injury or loss of life.
1.Always wear protective goggles for disassembly and reassembly to protect your eyes from ink in working. If any ink gets in your eyes, wash your eyes with clean water and consult a doctor immediately.
2.When using compressed air products; such as air duster, for cleaning during repair and maintenance, the use of such products containing flammable gas is prohibited.
PRECAUTIONS
Strictly observe the following cautions. Failure to comply may lead to personal injury or damage of the product.
1.Repairs on Epson product should be performed only by an Epson certified repair technician.
2.No work should be performed on this product by persons unfamiliar with basic safety knowledge required for electrician.
3.The power rating of this product is indicated on the serial number/rating plate. Never connect this product to the power source whose voltages is different from the rated voltage.
4.Replace malfunctioning components only with those components provided or approved by Epson; introduction of second-source ICs or other non-approved components may damage the product and void any applicable Epson warranty.
5.The capacitors on the Main Board may be electrically charged right after the power turns off or after driving motors which generates counter electromotive force such as when rotating the PF Roller or when moving the CR Unit. There is a risk to damage the Main Board if the Head FFC is short-circuited with the capacitors on the Main Board electrically charged, therefore, after the power turns off or after motors are driven, leave the printer untouched for approximately 30 seconds to discharge the capacitors before starting disassembly/ reassembly.
6.To prevent the circuit boards from short-circuiting, be careful about the following when handling FFC or cables.
When handling FFC, take care not to let the terminal section of FFC touch metal parts.
When connecting cables/FFC to the connectors on circuit boards, connect them straight to the connectors to avoid slant insertion.
Confidential
7.In order to protect sensitive microprocessors and circuitry, use static discharge equipment, such as anti-static wrist straps, when accessing internal components.
8.Do not tilt this product immediately after initial ink charge, especially after performing the ink charge several times. Doing so may cause ink to leak from the product because it may take some time for the waste ink pads to completely absorb ink wasted due to the ink charge.
9.Never touch the ink or wasted ink with bare hands. If ink comes into contact with your skin, wash it off with soap and water immediately. If you have a skin irritation, consult a doctor immediately.
10.When disassembling or assembling this product, make sure to wear gloves to avoid injuries from metal parts with sharp edges.
11.Use only recommended tools for disassembling, assembling or adjusting the printer.
12.Observe the specified torque when tightening screws.
13.Be extremely careful not to scratch or contaminate the following parts.
Nozzle plate of the Printhead
CR Scale
PF Scale
Coated surface of the PF Roller
Gears
Rollers
Scanner Sensor
Exterior parts
14.Never use oil or grease other than those specified in this manual. Use of different types of oil or grease may damage the component or give bad influence on the printer function.
15.Apply the specified amount of grease described in this manual.
16.Make the specified adjustments when you disassemble the printer.
17.When cleaning this product, follow the procedure described in this manual.
18.When transporting this product after filling the ink in the printhead, pack the printer without removing the ink cartridges in order to prevent the printhead from drying out.
19.Make sure to install antivirus software in the computers used for the service support activities.
20.Keep the virus pattern file of antivirus software up-to-date.
21.When disassembling/reassembling this product, if you find adhesive power of the double-sided tape which secure the parts or FFC is not enough, replace the tape with new one and attach it correctly to the specified points where the parts or FFC should be secured.
22.Unless otherwise specified in this manual, the labels attached on the returned product should be transferred to the corresponding attachment positions on the new one referring to the labels on the returned product.
Confidential
About This Manual
This manual, consists of the following chapters, is intended for repair service personnel and includes information necessary for properly performing maintenance and servicing the product.
CHAPTER 1. TROUBLESHOOTING
Describes the step-by-step procedures for the troubleshooting.
CHAPTER 2. DISASSEMBLY / REASSEMBLY
Describes the disassembly/reassembly procedures for main parts/units of the product, and provides the standard operation time for servicing the product.
CHAPTER 3. ADJUSTMENT
Describes the required adjustments for servicing the product.
CHAPTER 4. MAINTENANCE
Describes maintenance items and procedures for servicing the product.
CHAPTER 5. APPENDIX
Provides the following additional information for reference:
•Connector Diagram
•Points to be checked before packing the printer
•Protection for Transportation
Symbols Used in this Manual
Various symbols are used throughout this manual either to provide additional information on a specific topic or to warn of possible danger present during a procedure or an action. Pay attention to all symbols when they are used, and always read explanation thoroughly and follow the instructions.
Indicates an operating or maintenance procedure, practice or condition that, if not strictly observed, could result in serious injury or loss of life.
Indicates an operating or maintenance procedure, practice, or condition that, if not strictly observed, could result in bodily injury, damage or malfunction of equipment.
May indicate an operating or maintenance procedure, practice or condition that is necessary to accomplish a task efficiently. It may also provide additional information that is related to a specific subject, or comment on the results achieved through a previous action.
For Chapter 2 “Disassembly/Reassembly”, symbols other than indicated above are used to show additional information for disassembly/reassembly. For the details on those symbols, see "2.2 Disassembly/Reassembly Procedures (p31)".
Confidential
Revision Status
Revision |
Date of Issue |
Description |
|
|
|
|
|
A |
January 9, 2012 |
First Release |
|
|
|
|
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
Contents
Chapter 1 Troubleshooting
1.1 |
Troubleshooting............................................................................................................. |
............................................ 9 |
|
|
1.1.1 |
Troubleshooting Workflow .............................................................................................................................. |
9 |
1.2 |
Power-On Sequence ................................................................................................................................................ |
11 |
|
1.3 |
Fatal Error Code List............................................................................................................................................... |
13 |
|
|
1.3.1 |
Printer Fatal Error Code ................................................................................................................................. |
13 |
Chapter 2 Disassembly/Reassembly
2.1 |
Overview |
.................................................................................................................... ............................................. |
17 |
|
|
2.1.1 |
Tools ............................................................................................................................................................... |
17 |
|
|
2.1.2 |
Jigs .................................................................................................................................................................. |
|
17 |
|
2.1.2.1 ..............................................................................................Making the Spring Hook Jig .................... |
17 |
||
|
2.1.3 |
Locations ..............................................................................................of the Parts/Units ............................. |
18 |
|
|
2.1.4 |
Standard .........................................................................Operation Time for Servicing the Product ............. |
22 |
|
|
2.1.5 |
Checks ...............................................................................and Precautions before Disassembling ............... |
25 |
|
|
2.1.5.1 .................................................................................. |
Factors which Affect the Print Quality ................ |
25 |
|
|
2.1.5.2 |
Factors which Affect the Safety of Service Personnel such as Ink Leakage during Operation ............ |
26 |
|
2.2 |
Disassembly/Reassembly ...........................................................................................Procedures .......................... |
31 |
||
|
2.2.1 |
Disassembly .....................................................................................................Flowchart .............................. |
32 |
|
|
2.2.2 |
Disassembly ..............................................................................Flowchart (Printhead/Main Board) ............. |
40 |
|
2.3 |
Detailed Disassembly/Reassembly ................................................................Procedure for each Part/Unit ........... |
41 |
||
2.4 |
Routing FFCs/cables ............................................................................................................................................... |
50 |
Chapter 3 Adjustment
3.1 |
Required Adjustments ............................................................................................................................................. |
54 |
|
3.2 |
Adjustment Program................................................................................................................................................ |
59 |
|
|
3.2.1 |
Operating Environment .................................................................................................................................. |
59 |
|
3.2.2 |
Details of the Adjustment Program ................................................................................................................ |
59 |
|
3.2.2.1 CR Motor Heat Protection Control / PF Motor Heat Protection Control .............................................. |
59 |
|
|
3.2.3 |
Scanner Motor Heat Protection Control ......................................................................................................... |
60 |
3.3 |
Mechanism Adjustment / Check ............................................................................................................................. |
61 |
|
|
3.3.1 |
Checking the Platen Gap ................................................................................................................................ |
61 |
|
3.3.2 CR/PF Belt Tension Check............................................................................................................................. |
63 |
Chapter 4 Maintenance
4.1 |
Overview ................................................................................................................................................................. |
66 |
|
|
4.1.1 |
Cleaning.......................................................................................................................................................... |
66 |
|
4.1.2 |
Lubrication...................................................................................................................................................... |
66 |
4.2 |
Lubrication Points and Instructions......................................................................................................................... |
67 |
Chapter 5 Appendix
5.1 |
Connector Diagram ................................................................................................................................................. |
73 |
|
5.2 |
Points to be checked before packing the printer...................................................................................................... |
74 |
|
5.3 |
Protection for Transportation .................................................................................................................................. |
76 |
|
|
5.3.1 |
Securing the CR Unit...................................................................................................................................... |
76 |
|
5.3.2 |
Securing the Paper Support Assy ................................................................................................................... |
77 |
|
5.3.3 |
Securing the Ink Supply Tank Assy/Top Cover............................................................................................. |
78 |
7
Confidential
CHAPTER 1
TROUBLESHOOTING
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
1.1 Troubleshooting
This section describes the troubleshooting workflow and fatal error information.
In this chapter, the product names are called as follows:
L365/L366 Series:L365/L366
L360/L362 Series:L360,L363/L362
L310/L312 Series:L310,L313/L312
L220/L222 Series:L220/L222
L130/L132 Series:L130/L132
1.1.1Troubleshooting Workflow
The following page describes the troubleshooting workflow. Follow the flow when troubleshooting problems.
Troubleshooting |
Troubleshooting |
9 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Revision A |
|||||||||||||||||||||||
|
Start |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Major problem with error message |
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
Turn on the power*1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fatal error |
|
|
Incomplete Initial Ink Charge |
|
|
|
Maintenance error |
|
|
|
Ink End error |
|
|
Paper Jam Fatal error |
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
No |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Does printer turn on the |
|
|
|
|
|
|
|
|
|
|
|
|
Please refer to " 1.3 Fatal Error Code |
|
|
[Occurrence Condition] |
|
|
[Occurrence Condition] |
|
[Occurrence Condition] |
|
[Occurrence Condition] |
|
|
|
|
|
|
||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||
|
power? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
List (p13)". |
|
|
Ink LED is ON and STM |
|
|
This error occurs when |
|
This error occurs when ink |
|
This error occurs when CR Unit is |
|
|
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
indicates "Initial ink charging is |
|
|
maintenance counter in EEPROM |
|
counter reaches ink end level. |
|
blocked by jammed paper. |
|
|
|
|
|
|
||||||||||||||||||||||||
|
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
|
Major problem without |
|
|
|
|
|
|
|
|
|
|
not complete". |
|
|
exceeds the specified value. |
|
[Major Occurrence Timing] |
|
[Major Occurrence Timing] |
|
|
|
|
|
|
|||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
error message |
|
|
|
|
|
|
|
|
|
|
[Major Occurrence Timing] |
|
|
[Major Occurrence Timing] |
|
|
|
|
|
|
|
|
||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Power-on timing |
|
• |
Power-on timing |
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Print start timing. |
|
|
• |
Power-on timing |
|
• |
Print start timing |
|
[Major Troubleshooting] |
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
No Power*2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||
|
Is Power-on sequence |
|
|
No |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Print start timing |
|
• |
Cleaning timing |
|
|
|
|
|
|
|
||||||||||||||||||||||||
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Troubleshooting] |
|
|
• |
Cleaning timing |
|
|
|
|
|
|
|
|
• |
Remove jammed paper |
|
|
|
|
|
|
||||||||||||||||||
|
finished without error? |
|
|
|
|
|
|
[Presumable Cause] |
|
|
|
|
|
|
|
|
|
|
Perform initial ink charge |
|
|
• |
Ink Cartridge replacement |
|
[Troubleshooting] |
|
[NOTE] |
|
|
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
PS Unit damage |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
timing |
|
• Refill ink and reset ink counter |
|
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
by panel. |
|
On this product, if CR Unit |
|
|
|
|
|
|
||||||||||||
|
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Main Board damage |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Troubleshooting] |
|
|
|
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
touches jammed paper, CR Unit |
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Major Troubleshooting] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Porous Pad replacement & |
|
|
|
|
|
|
|
|
moves back in the opposite |
|
|
|
|
|
|
|||||||||||
|
Standby condition |
|
|
|
|
|
|
• |
PS Unit replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maintenance counter reset |
|
|
|
|
|
|
|
|
direction so that customer can |
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
remove the paper. However, if CR |
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
• |
Main Board replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Unit cannot move in this |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
sequence, this error occurs. |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Print check pattern |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
No |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
Does an error occur |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
when |
printing? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Paper Jam error |
|
|
|
|
No Paper error |
|
|
Double Feed error |
|
|
Paper Size Unmatch error |
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Occurrence Condition] |
|
|
[Occurrence Condition] |
|
[Occurrence Condition] |
|
|
[Occurrence Condition] |
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This error occurs when top/ |
|
|
This error occurs when top of |
|
When manual duplex printing is |
|
|
This error occurs if the actual |
|
|||||||||||||
|
Is printing operation |
|
No |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
bottom of paper is not detected by |
|
|
paper can not be detected |
|
selected using the printer driver, |
|
|
paper length detected by PE |
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PE Sensor in the specified steps of |
|
|
correctly by PE Sensor in the |
|
this error occurs if the actual |
|
|
Sensor does not match with the |
|
||||||||||||||||||||||||
|
finished without trouble? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
paper loading / ejecting operation |
|
|
specified steps up to completion |
|
paper length detected by PE |
|
|
paper length specified in the |
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
correctly. |
|
|
of the paper loading operation. |
|
Sensor does not match with the |
|
|
printer driver. (The error occurs |
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Major Occurrence Timing] |
|
|
(No paper / No loading / large |
|
paper length specified in the |
|
|
no matter when the actual length |
|
|||||||||||||
|
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
paper skew) |
|
printer driver. (The error occurs |
|
|
is longer or shorter than the |
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Power-on timing |
|
|
[Major Occurrence Timing] |
|
when the actual length is longer |
|
|
theoretical length specified in the |
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
Copy an image |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Major problem without error message |
|
|
|
|
|
|
• |
Paper loading timing |
|
|
|
than the theoretical length |
|
|
driver.) |
|
|||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Paper eject timing |
|
|
• |
Paper loading timing |
|
specified in the driver.) |
|
|
[Major Occurrence Timing] |
|
|||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Major Troubleshooting] |
|
|
[Major Troubleshooting] |
|
[Major Occurrence Timing] |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Poor Printing |
|
|
Poor Paper Loading |
|
|
|
|
|
|
|
|
|
• |
Paper eject timing |
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Perform paper eject operation |
|
|
1 Set paper in ASF and perform |
|
• |
Paper loading timing |
|
|
[Troubleshooting] |
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
from operation panel. |
|
|
|
paper feed operation. |
|
• |
Paper eject timing |
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||
|
Is scanning operation |
|
|
|
|
No |
|
|
|
|
|
|
|
|
|
|
[Phenomenon] |
|
[Presumable Cause] |
|
|
• |
Success |
|
|
2 If the paper stops before |
|
[Troubleshooting] |
|
|
• PE Sensor Lever replacement |
|
||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Poor printing quality |
|
• Use of 3rd party media |
|
|
|
|
|
Starts paper feeding |
|
|
|
reaching PE Sensor, remove it |
|
|
|
• |
PE Sensor replacement |
|
|||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||
|
finished without trouble? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Ink stain on paper |
|
• |
Edge guide mis-setting |
|
|
|
|
|
operation again if printer has |
|
|
|
and check the paper condition. |
|
• PE Sensor Lever replacement |
|
|
|
(Main Board replacement) |
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Dot missing |
|
• |
Foreign material |
|
|
|
print data. |
|
|
3 A) If paper is OK, set paper in |
|
• |
PE Sensor replacement |
|
|
• |
Main Board replacement |
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Paper eject without printing |
|
• |
Part come-off |
|
|
• |
Fail |
|
|
|
|
ASF and move edge guides to |
|
|
(Main Board replacement) |
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||
|
Yes |
|
|
|
|
|
|
|
|
|
Scanner failure |
|
|
|
|
|
|
|
|
|
|
• Contamination of LD Roller or |
|
|
|
|
|
Occurs paper jam error |
|
|
|
|
appropriate position, and |
|
• |
Main Board replacement |
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
[Presumable Cause] |
|
|
PF roller |
|
|
|
|
|
again. |
|
|
|
|
perform 2 again. |
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[NOTE] |
|
|
|
|
|
|
|||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
[Presumable Cause] |
|
|
|
|
|
|
|
|
• |
Driver / Panel mis-setting |
|
[Major Troubleshooting] |
|
|
|
|
2 If fail in the above 1, remove |
|
|
|
B) If damage in the above 2, |
|
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Contamination of CR scale |
|
|
|
|
|
|
the paper by opening Scanner |
|
|
|
|
check foreign materials / |
|
This error may occur in the |
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• Contamination of Scanner Glass |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Contamination of Printhead |
|
• |
Recommendation of EPSON |
|
|
|
|
|
Unit. |
|
|
|
|
parts come-off / parts |
|
manual duplex printing if the |
|
|
|
|
|
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• Contamination of Document Pad |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
cover |
|
|
media |
|
|
|
|
3 Perform paper eject operation |
|
|
|
|
transformation in paper |
|
inverted sheet printed on the first |
|
|
|
|
|
|
|||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• CIS Unit bonding failure |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Printhead damage |
|
• |
Edge guide re-setting |
|
|
|
|
|
from operation panel again. |
|
|
|
|
path. |
|
side sticks to the second sheet |
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
CIS Unit damage |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Ink clogging of Printhead |
|
• |
Foreign material removal |
|
|
|
|
• |
Success |
|
|
4 If not resolved by 3-A & 3-B, |
|
when the first side printing is |
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Scanner Motor damage |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Contamination on Cap Unit / |
|
• |
Part re-installation |
|
|
|
|
|
Starts paper feeding |
|
|
|
check foreign material / Part |
|
complete and the sheet is inverted |
|
|
|
|
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Insufficient grease |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wiper of Ink System Assy |
|
• |
Roller replacement |
|
|
|
|
|
operation again if printer has |
|
|
|
come-off / surface condition of |
|
and set to ASF to print on the |
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
[Major Troubleshooting] |
|
|
|
|
|
|
|
|
• Ink System Assy damage |
|
|
|
|
|
|
|
|
|
|
|
print data. |
|
|
|
LD Roller or PF Roller / PE |
|
other side. |
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Float of Porous Pad on Paper |
|
|
|
|
|
|
|
|
|
|
• |
Fail |
|
|
|
Sensor Lever / PE Sensor / |
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Scanner Glass cleaning |
|
|
|
|
|
|
|
|
|
Guide Front |
|
|
Abnormal Noise |
|
|
|
|
|
Occurs paper jam error |
|
|
|
Main Board / PF Motor. |
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Document Pad cleaning |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Narrower/Wider PG |
|
|
|
|
|
|
|
|
|
|
|
again. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Document Pad replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(out of standard) |
|
[Presumable Cause] |
|
|
|
|
4 If fail in the above 3, check |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
CIS Unit replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• PE Sensor Lever damage |
|
• |
Foreign material |
|
|
|
|
|
foreign material / part come- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Scanner Motor replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
PE Sensor damage |
|
• |
Insufficient grease |
|
|
|
|
|
off / PE Sensor Lever / PE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
• |
Lubrication of grease |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Ink tank ventilation film gets |
|
• |
Gear damage |
|
|
|
|
|
Sensor / Porous Pad on Paper |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
wet. |
|
[Major Troubleshooting] |
|
|
|
|
|
Guide Front / Main board. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Major Troubleshooting] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Foreign material removal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Driver / Panel re-setting |
|
• |
Lubrication of grease |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
CR Scale replacement |
|
• |
Gear replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Printhead cover cleaning |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*1: If the Hopper of ASF on the returned product touches the LD Roller, the initial ink charge has |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Printhead cleaning |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Ink Cartridge replacement |
|
|
Blank printing |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
not been completed for the product yet. |
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Printhead replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*2: If the printer can turn on but turns off right away, the protection circuit may cut off the power |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Rubber cleaning of Cap Unit |
|
[Phenomenon] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
due to an error such as a circuit failure. |
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Ink System Assy replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Blank printing |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*3: In case of “Not Trouble Found”, check fatal error code. |
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Porous Pad re-installation |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Printer replacement |
|
[Presumable Cause] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• PE Sensor Lever replacement |
|
• Ink tank ventilation film gets |
|
|
|
|
|
|
|
|
|
|
|
|
|
If the reason for the return is evident, first check the phenomenon user |
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
PE Sensor replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
wet |
|
|
|
|
|
|
|
|
|
|
|
|
|
claims recurs, then proceed to the troubleshooting. |
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(Main Board replacement) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Ink rumples |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Ink tank replacement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Ink onnection is incomplete. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This flowchart is compiled based on the following contents. |
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Major Troubleshooting] |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Ink tank replacement |
|
|
|
|
|
|
|
|
|
|
|
• Our experience regarding the quality problem. |
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||
|
Finish*3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
Ink tube re-installation |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• ESK’s repair data. |
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Printer Mechanism specification for the product.
Troubleshooting |
Troubleshooting Workflow |
10 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
1.2 Power-On Sequence
This section describes the power-on sequences in two conditions. The preconditions are as follows.
Condition 1: Normal power-on sequence (See Table 1-1.)
Turning on the printer after turning it off without an error.
Initial ink charge has finished and every cartridge has sufficient ink.
No paper on the paper path.
The Printhead is capped with the Cap Assy.
The CR Unit is normally fixed by the Change Lever.
Maintenance error recovery has never been performed.
Table 1-1. Condition 1: Normal Power-on Sequence
|
Operation*1 |
|
|
CR Unit/PF Roller |
||||||||||||
|
|
|
|
|
movement and |
|||||||||||
|
|
|
|
|
|
position*2 |
||||||||||
1. |
Printhead initialization and fuse inspection |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1-1.Initializes the Printhead, and checks for the fuse on the circuit boards in the printer.*3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2. |
Checking for waste ink overflow |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2-1.Checks the waste ink counter if the waste ink overflow is occurring. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3. |
Seeking the home position |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3-1.The CR Unit moves to the 80-digit side slowly and confirms it touches the Change Lever (CR lock). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3-2.The CR Unit moves to the 0-digit side slowly. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3-3.After the PE Sensor checks if paper exists, the PF Motor rotates clockwise for one second and releases the CR lock. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3-4.While checking if the CR Unit does not touch the Change Lever (CR lock) or the foreign material, the CR Unit |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
moves to the 80-digit side slowly until it touches the Left Frame. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3-5.The distance from the position where the CR Unit touched to the Left Frame is regarded as the standard distance |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
from the origin position, and the home position is fixed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
From then on, the CR Unit position is monitored according to the signals from the CR Encoder. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3-6.The CR Unit moves to near its home position quickly. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4. |
PF Motor Measurement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4-1.The PF Motor rotates clockwise until the PF Roller turns five times to perform a load measurement. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5. |
Detecting ink cartridge and initializing ink system*4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5-1.The CR Unit returns to its home position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6. |
Low temperature operation sequence*5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6-1.The CR Unit quickly moves back and forth between near the Change Lever and near the Left Frame for two times. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note 1: The rotation directions of the PF Motor are as follows.
Clockwise: |
Paper is fed normally |
Counterclockwise: |
Paper is fed backward |
*2: The conditions of the CR lock are as follows.
Red |
CR lock is set |
White |
CR lock is released |
*3: The fatal error occurs if there is a problem such as the fuse blew. *4: The empty suction operation may occur depending on the situation.
*5: Executed when the detected temperature is under 5 oC (41oF) by the thermistor on the Printhead.
Troubleshooting |
Power-On Sequence |
11 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
Condition 2: Power-on sequence after recovering from a paper jam error (See Table 1-2.)
Turning on the printer after turning it off with a paper jam fatal error.
There still remains paper on the paper path out of the detecting area of the PE Sensor.
Maintenance error recovery has never been performed.
Table 1-2. Condition 2: Power-on Sequence after Recovering from a Paper Jam Error
|
CR Unit/PF Roller |
||||||||||||||
|
|||||||||||||||
Operation |
|
|
movement and |
||||||||||||
|
|
|
|
|
|
|
position |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Executes No.1 to No.3 on the normal power-on sequence (Table 1-1). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4. Detecting remaining paper |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4-1.5.The CR Unit returns to its home position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4-2.The CR Unit moves to the 80-digit side and confirms there is no paper.*1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4-3.The CR Unit quickly returns to its home position, and displays on the LCD or with flashing LEDs that the paper jam error occurs.
When the user removes the paper and releases the paper jam error by panel operation, the normal power-on sequence from No.1 (Table 1-1) is executed again.*2
Note *1: “Paper exists” is detected when the CR Unit touches the paper. When “paper does not exist” is detected, the power-on sequence of condition 1 (Table 1-1) is executed from No.4.
*2: If the paper jam error cannot be solved after repeating the power-on sequence on condition 2 (Table 1-2) twice, the printer turns into the paper jam fatal error for the third time.
To recover from the maintenance error, the dedicated software that can be downloaded from the web site which can be accessed from STM3 is required.
The printer operation related to the maintenance error recovery is as follows.
•When the waste ink counter reaches the threshold value (1) for the first time and the maintenance error occurs, the counter threshold of the maintenance error is changed to threshold value 2 after performing recovery from the maintenance error.
•After the threshold value (2) is enabled, the warning; to notify the possibility of ink leakage out of the printer, is displayed every time the waste ink counter increases by 1%.
•If the waste ink counter reaches the threshold value (2), the maintenance error occurs. Then, the waste ink counter is changed back to the threshold value (1) after recovering from the maintenance error, and the warning is displayed repeatedly according to the increment of the waste ink counter until the maintenance error occurs when the threshold value (2) is reached.
(Recovery from the maintenance error can be performed up to the specified number of times.)
Troubleshooting |
Power-On Sequence |
12 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
1.3 Fatal Error Code List
This section describes how to check the fatal error code, description, and the possible causes.
1.3.1 Printer Fatal Error Code
This section describes the fatal error code and the possible cause for this product.
Error type |
Error |
Error name |
|
Possible cause |
|
||||
code |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
• |
CIS Unit failure |
|
|
|
• |
Scanner Housing failure |
|
0x10 |
HP detection failure |
• |
Main Board failure |
|
• |
Insufficient grease |
||
|
|
|
||
|
|
|
• |
Foreign object |
|
|
|
• FFC for CIS failure / FFC for CIS connection failure |
|
|
|
|
|
|
|
|
|
• Scanner drive mechanism was overloaded. |
|
|
|
|
• |
Insufficient grease |
|
0x14 |
Measurement error |
• |
Foreign object |
Scanner |
|
|
• |
Lack of gears |
|
|
• Deformation of the shaft |
||
|
|
|
||
|
|
|
|
|
|
0x20 |
LED light failure |
• |
CIS Unit failure |
|
• |
Main Board failure |
||
|
|
|
||
|
|
|
|
|
|
0x51 |
Auto judge Fatal Error 1 |
|
|
|
|
|
|
|
|
0x52 |
Auto judge Fatal Error 2 |
|
|
|
|
|
|
---* |
|
0x53 |
Auto judge Fatal Error 3 |
|
|
|
|
|
|
|
|
0x54 |
Auto judge Fatal Error 4 |
|
|
|
|
|
|
|
|
0x55 |
Auto judge Fatal Error 5 |
|
|
|
|
|
|
|
|
|
|
• Carriage overload error (paper jam/foreign object) |
|
|
|
|
• Deformation of the Main Frame |
|
|
|
|
• |
Ink system failure |
|
0x60 |
Home position |
• |
CR Motor failure |
|
• Deformation of the Front Frame |
|||
|
|
|
||
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
failure) |
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
Ink cartridge replacement timing contact |
• |
Paper jam |
|
0x63 |
• |
Foreign object |
|
|
detection error (Power off) |
|||
|
|
• Deformation of the Main Frame |
||
|
|
|
||
|
|
|
|
|
|
0x64 |
Paper-Jam cancelation disable error |
• |
Paper jam |
|
• |
Foreign object |
||
|
|
|
||
|
|
|
|
|
|
0x81 |
PIS environmental error |
• |
Diffused light |
Printer |
|
|
|
|
|
|
• |
PIS failure |
|
|
0x82 |
PIS continuous reflected light error |
• |
Main Board failure |
|
|
|
• |
Diffused light |
|
|
|
|
|
|
0x83 |
PIS No reflected light error |
• |
PIS failure (installation posture, contamination) |
|
|
|
|
|
|
0x84 |
PIS shift length error |
• |
Home position gap |
|
• |
Diffused light |
||
|
|
|
||
|
|
|
|
|
|
0x87 |
PIS Empty Jig error |
• |
PIS failure (installation posture, contamination) |
|
|
|
|
|
|
|
|
• |
PIS failure |
|
0x88 |
Excessive Light error |
• |
Main Board failure |
|
|
|
• |
Diffused light |
|
|
|
|
|
|
|
|
• PIS failure (installation posture, contamination) |
|
|
0x89 |
Insufficient Light error |
• |
Main Board failure |
|
|
|
• |
Ink cartridge failure |
|
|
|
|
|
|
0x8F |
EEPROM verify error (by command) |
|
---* |
|
|
|
|
|
Troubleshooting Fatal Error Code List 13
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
|
Revision A |
||||
|
|
|
|
|
|
|
|
Error type |
Error |
Error name |
|
Possible cause |
|
|
code |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0x9A |
Circuit error (include blowout of a fuse) |
• |
Main Board failure |
|
|
|
|
|
|
||
|
|
0x9B |
Transistor temperature error |
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
0x9C |
X-Hot detect error (pre printing) |
|
|
|
|
|
|
|
• |
Printhead failure |
|
|
|
0x9D |
X-Hot detect error (after flushing) |
|
||
|
|
• |
Main Board failure |
|
||
|
|
|
|
|
||
|
|
0x9E |
Head temperature error |
|
|
|
|
|
|
|
|
|
|
|
|
0xB9 |
Other Ink device error |
|
|
|
|
|
|
|
• |
Ink cartridge failure |
|
|
|
0xBA |
Other Ink device error |
|
||
|
|
• |
CSIC Terminal failure |
|
||
|
|
|
|
|
||
|
|
0xC0 |
CRCM access error |
• |
CR Contact Module failure |
|
|
|
|
|
• |
Main Board failure |
|
|
|
0xC1 |
CRCM access error |
|
||
|
|
• |
Cable disconnection |
|
||
|
|
|
|
|
||
|
|
0xC3 |
Other Ink device error |
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xE1 |
CR PID excess load error |
• |
CR Motor failure |
|
|
|
|
|
• Carriage overload error (paper jam/foreign object) |
|
|
|
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xE2 |
CR PID excess speed error |
• |
Motor driver failure (Main Board failure) |
|
|
|
|
|
• Slipping teeth of the CR Timing Belt |
|
|
|
|
|
|
• Improper tension of the CR Timing Belt |
|
|
|
|
|
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xE3 |
CR PID reverse error |
• |
Slipping teeth of the CR Timing Belt |
|
|
|
|
|
• Improper tension of the CR Timing Belt |
|
|
|
|
|
|
• Carriage overload error (paper jam/foreign object) |
|
|
|
Printer |
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
||
|
|
|
|
|
||
|
|
|
|
|
failure) |
|
|
|
0xE4 |
CR PID lock error |
• |
CR Motor failure |
|
|
|
|
|
• Carriage overload error (paper jam/foreign object) |
|
|
|
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xE8 |
CR load position reverse error |
• |
Slipping teeth of the CR Timing Belt |
|
|
|
|
|
• Improper tension of the CR Timing Belt |
|
|
|
|
|
|
• Carriage overload error (paper jam/foreign object) |
|
|
|
|
|
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xE9 |
CR load position excess speed error |
• |
Motor driver failure (Main Board failure) |
|
|
|
|
|
• Slipping teeth of the CR Timing Belt |
|
|
|
|
|
|
• Improper tension of the CR Timing Belt |
|
|
|
|
|
|
|
|
|
|
|
|
|
• CR Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xEA |
CR load position excess load error |
• |
CR Motor failure |
|
|
|
|
|
• Carriage overload error (paper jam/foreign object) |
|
|
|
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
|
|
|
0xEE |
CR PID driving time error |
|
|
|
|
|
|
|
• |
Main Board failure |
|
|
|
0xEF |
CR load position excess driving time |
|
||
|
|
|
|
|
||
|
|
error |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xF1 |
PF PID excess load error |
• |
PF Motor failure |
|
|
|
|
|
• PF drive mechanism overload (paper jam/foreign object) |
|
|
|
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
|
Troubleshooting |
Fatal Error Code List |
14 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
|
Revision A |
||||
|
|
|
|
|
|
|
|
Error type |
Error |
Error name |
|
Possible cause |
|
|
code |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
0xF2 |
PF PID excess speed error |
|
failure) |
|
|
|
• Motor driver failure (Main Board failure) |
|
|||
|
|
|
|
|
||
|
|
|
|
• Slipping gears have occurred around the PF Motor gears. |
|
|
|
|
|
|
|
|
|
|
|
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
0xF3 |
PF PID reverse error |
|
failure) |
|
|
|
• Slipping gears have occurred around the PF Motor gears. |
|
|||
|
|
|
|
|
||
|
|
|
|
• |
Paper jam |
|
|
|
|
|
|
|
|
|
|
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xF4 |
PF PID lock error |
• |
PF Motor failure |
|
|
|
|
|
• PF drive mechanism overload (paper jam/foreign object) |
|
|
|
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
|
|
Printer |
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
0xF8 |
PF load position reverse error |
|
failure) |
|
|
|
|
|
|
|||
|
|
|
|
• Slipping gears have occurred around the PF Motor gears. |
|
|
|
|
|
|
|
|
|
|
|
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
0xF9 |
PF load position reverse error |
|
failure) |
|
|
|
• Motor driver failure (Main Board failure) |
|
|||
|
|
|
|
|
||
|
|
|
|
• Slipping gears have occurred around the PF Motor gears. |
|
|
|
|
|
|
|
|
|
|
|
|
|
• PF Encoder failure (contaminated/detached scale, Encoder Board |
|
|
|
|
|
|
|
failure) |
|
|
|
0xFA |
PF load position excess load error |
• |
PF Motor failure |
|
|
|
|
|
• PF drive mechanism overload (paper jam/foreign object) |
|
|
|
|
|
|
• |
Cable disconnection |
|
|
|
|
|
|
|
|
|
|
0xFE |
PF PID driving time error |
• |
Main Board failure |
|
|
|
|
|
|
||
|
|
0xFF |
PF load position excess driving time error |
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
Note "*": Not occurs except in manufacturing process.
Troubleshooting |
Fatal Error Code List |
15 |
Confidential
CHAPTER 2
DISASSEMBLY/REASSEMBLY
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
2.1 Overview
In this chapter, the product names are called as follows:
L360/L362 Series:L365/L366
L360/L362 Series:L360,L363/L362
L310/L312 Series:L310,L313/L312
L220/L222 Series:L220/L222
L130/L132 Series:L130/L132
This chapter describes procedures for disassembling the main parts/units of this product. Unless otherwise specified, disassembled parts/units can be reassembled by reversing the disassembly procedure. See the cautions or tips for disassembly/reassembly described in "2.3 Detailed Disassembly/Reassembly Procedure for each Part/ Unit (p41)".
Read the "Safety Precautions(p3)" before disassembling and reassembling.
When you have to remove units or parts that are not described in this chapter, see the exploded diagrams of SPI (Service Parts Information).
2.1.1 Tools
Use only specified tools to avoid damaging the printer.
Name |
Availability |
EPSON Part Code |
|
|
|
(+) Phillips screwdriver #1 |
O |
1080530 |
|
|
|
(+) Phillips screwdriver #2 |
O |
--- |
|
|
|
Flathead screwdriver |
O |
--- |
|
|
|
Flathead Precision screwdriver #1 |
O |
--- |
|
|
|
Tweezers |
O |
--- |
|
|
|
Longnose pliers |
O |
--- |
|
|
|
Acetate tape |
--- |
1003963 |
|
|
|
Note 1: Some of the tools listed above are commercially available.
2:EPSON provides the tools listed with EPSON part code.
2.1.2Jigs
Name |
Quantity |
EPSON Part Code |
|
|
|
Spring hook jig* |
1 |
Can be made with a commercial item See " Making the Spring Hook Jig (p17)". |
|
|
|
Thickness gauge (1.5 mm) |
2 |
Commercially available |
|
|
|
Thickness gauge (2.0 mm) |
2 |
Commercially available |
|
|
|
Sonic tension meter |
1 |
1294120 |
|
|
|
Note *: If performing the disassembling/reassembling procedure is difficult using tweezers such as when reassembling " Cap Lever/Cap Assy (p44)", the spring hook jig helps you to remove/attach the spring easier.
2.1.2.1 Making the Spring Hook Jig
Fold a clip (commercial item) as shown in Fig. 2-1.
Before folding |
|
|
|
|
|
After folding |
|
|
||
|
|
|
|
|
|
|
|
40 mm or more |
|
|
|
|
Fold here |
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Clip |
|
|
|
|
|
Clip |
Fold appropriate length to hitch a spring.
Figure 2-1. Making the Spring Hook Jig
Disassembly/Reassembly |
Overview |
17 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
2.1.3 Locations of the Parts/Units
This section shows the locations of the main parts/units of this product.
The parts/units which can not be seen in the following pictures are indicated in dotted lines ( ).
Exterior parts |
|
|
|
|
|
|
Front |
1 |
|
Right |
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
6 |
|
2 |
3 |
4 |
|
|
|
|
|
8 |
Rear |
|
|
Left |
|
|
|
|
|
|
|
7 |
|
9 |
No. |
Name |
|
No. |
Name |
|
1 |
Housing Rear (p33) (L365/L366,L360/L362,L220/L222 |
5 |
Hinge (p37) (L365/L366,L360/L362,L220/L222 Series |
||
Series only) |
|
|
only) |
||
|
|
|
|
||
2 |
Tray Front Assy (p33) |
|
|
6 |
Housing Right (p37) (L365/L366,L360/L362,L220/L222 |
|
|
Series only) |
|||
|
|
|
|
|
|
3 |
Frame Base Assy (p35) |
|
|
7 |
Housing Left (p33) (L365/L366,L360/L362,L220/L222 |
|
|
|
Series only) |
||
|
|
|
|
|
|
|
Panel Unit |
|
|
|
Scanner Unit (p33) (L365/L366,L360/L362,L220/L222 |
|
• L365/L366 Series (p 35) |
|
|
Series only) |
|
|
Panel Board Assy (p38) / Panel Buttons (p38) / |
8 |
Scanner Housing Upper (p37) / Scanner Carriage Unit |
||
|
Panel Housing Upper Assy (p38) / Panel Housing |
|
(p37) / Scanner Housing Lower (p37) / CIS Module |
||
4 |
Lower Assy (p38) |
|
|
|
Unit (p37) / Scanner Motor (p37) |
• L360/L362,L220/L222 Series (p 35) |
|
9 |
Paper Support Assy (p33) |
||
|
|
||||
|
Panel Board Assy (p38) / Panel Buttons (p38) / |
|
|
||
|
Panel Housing Upper Assy (p38) / Panel Housing |
|
|
||
|
Lower Assy (p38) |
|
|
|
|
Figure 2-2. Exterior Parts
Disassembly/Reassembly |
Overview |
18 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
|
Revision A |
||
|
Printer mechanism |
|
|
|
|
|
|
|
|
3 |
4 |
5 |
|
|
2 |
|
6 |
|
|
1 |
|
|
|
|
|
|
|
7 |
|
|
8 |
9 |
10 |
|
|
11 |
12 |
|
|
|
|
|
|
|
|
No. |
Name |
|
|
No. |
|
|
Name |
|
|
|
|
|
|
|
|
1 |
CR Driven Pulley Assy (p35) |
|
|
7 |
|
CR Unit (p39) |
|
|
|
|
|
|
|
|
|
2 |
CR Scale (p35) |
|
|
8 |
|
PF Roller Unit (p39) |
|
|
|
|
|
|
|
|
|
3 |
CR Timing Belt (p39) |
|
|
9 |
|
Star Wheel Holder Assy (p37) |
|
|
|
|
|
|
|
|
|
4 |
Printhead (p33) |
|
|
10 |
|
Paper Guide Upper Assy (p39) |
|
|
|
|
|
|
|
|
|
5 |
CR Encoder Sensor (p39) |
|
|
11 |
|
Paper Guide Front Unit (p33) |
|
|
|
|
|
|
|
|
|
6 |
Adapter (p37) |
|
|
12 |
|
Adapter Cover (p37) |
|
|
|
|
|
|
|||
|
|
Figure 2-3. Printer Mechanism: Front |
|||||
|
|
|
|
|
|
||
|
|
|
1 |
2 |
3 |
||
|
|
|
|
|
|
|
4 |
|
|
|
|
|
|
5 |
|
6 |
7 |
|
|
8 |
9 |
|
|
|
|
|
|
|
No. |
Name |
|
|
No. |
|
Name |
|
|
|
|
|
|
|
1 |
LD Roller Cover (p35) |
|
6 |
Cap Lever (p37) |
|
|
|
|
|
|
|
|
|
2 |
LD Roller Assy (p35) |
|
7 |
Cap Assy (p37) |
|
|
|
|
|
|
|
||
3 |
Hopper (p35) |
|
8 |
Porous Pad for Cap Assy (p37) |
||
|
|
|
|
|
|
|
4 |
Retard Roller Assy (p33) |
|
9 |
Pump Unit (p39) |
|
|
|
|
|
|
|
|
|
5 |
Paper Back Lever (p33) |
|
|
|
|
|
|
|
|
|
|
|
|
Figure 2-4. Printer Mechanism: Right
Disassembly/Reassembly |
Overview |
19 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
1
2
|
3 |
|
|
|
|
|
4 |
5 |
6 |
7 |
|
|
|
||||
|
|
|
|
|
|
No. |
Name |
|
|
No. |
Name |
|
|
|
|
|
|
1 |
Wireless LAN Module (p33) (L365/L366 Series only) |
5 |
PF Scale (p36) |
||
|
|
|
|
|
|
2 |
EJ Roller (p37) |
|
6 |
PF Encoder Sensor (p36) |
|
|
|
|
|
|
|
3 |
PF Motor Assy (p39) |
|
7 |
EJ Roller Gear (p33) |
|
|
|
|
|
|
|
4 |
PF Timing Belt (p36) |
|
|
|
|
|
|
|
|
|
|
|
Figure 2-5. Printer Mechanism: Left |
||||
|
|
|
|
|
|
|
|
2 |
|
|
3 |
|
1 |
|
|
|
|
|
|
5 |
6 |
|
|
|
|
|
4 |
|
|
|
|
|
|
No. |
Name |
No. |
Name |
|
|
|
|
1 |
CR Motor (p35) |
4 |
Waste Ink Pad Assy (p33) |
|
|
|
|
2 |
Head FFC (p39) |
5 |
PE Sensor Lever (p35) |
|
|
|
|
3 |
Main Board (p35) |
6 |
PS Unit (p33) |
|
|
|
|
Figure 2-6. Printer Mechanism: Rear
Disassembly/Reassembly |
Overview |
20 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
Ink Supply Tank Assy
|
2 |
3 |
4 |
|
5 |
|
|
1 |
|
|
|
|
|
|
|
|
|
|
6 |
|
|
|
|
9 |
8 |
7 |
|
|
10 |
|
|
|
|
|
No. |
Name |
|
|
|
No. |
Name |
1 |
Cover Joint (p36) |
|
|
|
7 |
Guide Tube Tank (p36) |
2 |
Top Cover (p36) |
|
|
|
|
Ink Supply Tank |
3 |
Right Cover (p36) |
|
|
|
8 |
Ink Supply Tank (Cyan) (p36)/Ink Supply Tank |
|
|
|
(Magenta) (p36)/Ink Supply Tank (Yellow) (p36)/Ink |
|||
4 |
Ink Supply Tank Tube Assy (p36) |
|
|
|
|
|
|
|
|
|
Supply Tank (Black) (p36) |
||
5 |
Ink Supply Tube Assy (p37) |
|
|
|
9 |
Bottom Cover (p36) |
6 |
Cover Tube Tank (p36) |
|
|
|
10 |
Left Cover (p36) |
Figure 2-7. Ink Supply Tank Assy
Disassembly/Reassembly |
Overview |
21 |
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
Revision A |
2.1.4 Standard Operation Time for Servicing the Product
The following are the standard operation time for servicing the product. This standard operation time was determined with the MTTR result measured using the prototype of L360/L362 Series which have the most functions. For other models described in this manual, perform the repair work referring to this standard operation time though the time varies due to the structural difference between models.
The underlined parts/units are supplied as After Service Parts.
Table 2-1. Standard Operation Time
|
|
|
Time (mm:ss) |
|
|
Parts/Unit |
|
Adjustment/ |
|
|
Replacement |
Total |
||
|
|
|||
|
|
inspection |
||
|
|
|
|
|
|
|
|
|
|
Housing Rear |
|
0:49 |
--- |
0:49 |
|
|
|
|
|
Paper Support Assy |
|
0:12 |
--- |
0:12 |
|
|
|
|
|
Tray Front Assy |
|
0:13 |
1:31 |
1:44 |
|
|
|
|
|
Document Cover |
|
0:10 |
--- |
0:10 |
|
|
|
|
|
Star Wheel Holder Assy |
|
3:47 |
3:18 |
7:05 |
|
|
|
|
|
Paper Guide Front Unit |
|
0:37 |
7:44 |
8:21 |
|
|
|
|
|
Holder Board |
|
3:16 |
--- |
3:16 |
|
|
|
|
|
FFC Cover Outer |
|
2:05 |
--- |
2:05 |
|
|
|
|
|
Print Head |
|
4:54 |
17:39 |
22:33 |
|
|
|
|
|
Waste Ink Pad Assy |
|
0:31 |
0:45 |
1:16 |
|
|
|
|
|
Paper Back Lever |
|
1:41 |
--- |
1:41 |
|
|
|
|
|
Retard Roller Assy |
|
1:49 |
0:47 |
2:36 |
|
|
|
|
|
Scanner Unit |
|
1:46 |
2:52 |
4:36 |
|
|
|
|
|
Scanner Housing Upper |
|
3:17 |
--- |
3:17 |
|
|
|
|
|
Scanner Housing Lower |
|
3:17 |
--- |
3:17 |
|
|
|
|
|
CIS Module Unit |
|
3:26 |
--- |
3:26 |
|
|
|
|
|
Spacer |
|
3:54 |
--- |
3:54 |
|
|
|
|
|
CIS Module |
|
3:54 |
--- |
3:54 |
|
|
|
|
|
Scanner Carriage Unit |
|
3:37 |
--- |
3:37 |
|
|
|
|
|
Scanner Carriage |
|
4:15 |
--- |
4:15 |
|
|
|
|
|
CIS Holder Unit |
|
7:05 |
--- |
7:05 |
|
|
|
|
|
Scanner Motor |
|
7:05 |
2:52 |
9:57 |
|
|
|
|
|
Housing Left |
|
2:44 |
--- |
2:44 |
|
|
|
|
|
PS Unit |
|
3:13 |
1:28 |
4:41 |
|
|
|
|
|
PF Encoder Sensor |
|
3:20 |
--- |
3:20 |
|
|
|
|
|
PF Scale |
|
3:35 |
--- |
3:35 |
|
|
|
|
|
PF Driven Pully Assy |
|
4:10 |
1:10 |
5:20 |
|
|
|
|
|
PF Timing Belt |
|
4:57 |
1:10 |
6:07 |
|
|
|
|
|
Wireless LAN Module |
|
3:18 |
--- |
3:18 |
|
|
|
|
|
EJ Roller Gear |
|
2:58 |
--- |
2:58 |
|
|
|
|
|
EJ Roller |
|
5:08 |
3:18 |
8:26 |
|
|
|
|
|
Hinge |
|
2:02 |
--- |
2:02 |
|
|
|
|
|
Housing Right |
|
2:16 |
--- |
2:16 |
|
|
|
|
|
Cap Assy |
|
3:16 |
--- |
3:16 |
|
|
|
|
|
Porous Pad for Cap Assy |
|
3:23 |
--- |
3:23 |
|
|
|
|
|
Disassembly/Reassembly Overview 22
Confidential
|
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
|
|
Revision A |
|
|||||
|
|
|
|
Table 2-1. Standard Operation Time |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Time (mm:ss) |
|
|
|
|
|
Parts/Unit |
|
|
|
Adjustment/ |
|
|
|
|
|
|
|
|
Replacement |
Total |
|
|
|||
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
inspection |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cap Lever |
|
|
3:32 |
--- |
3:32 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel Unit |
|
|
4:21 |
--- |
4:21 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel Housing Lower Assy |
|
|
5:02 |
--- |
5:02 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel Board Assy |
|
|
5:21 |
--- |
5:21 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel Bottons |
|
|
5:37 |
--- |
5:37 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel Housing Upper Assy |
|
|
5:37 |
--- |
5:37 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR Scale |
|
|
4:06 |
--- |
4:06 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LD Roller Cover |
|
|
4:03 |
--- |
4:03 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LD Roller Assy |
|
|
5:29 |
0:47 |
6:16 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Hopper |
|
|
4:06 |
6:03 |
10:09 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FFC Holder MB |
|
|
4:45 |
--- |
4:45 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Shield Plate |
|
|
7:56 |
--- |
7:56 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PE Sensor Lever |
|
|
9:26 |
0:47 |
10:13 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Main Board |
|
EEPROM Data Copy OK |
|
8:37 |
1:10 |
9:47 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
EEPROM Data Copy NG |
|
8:37 |
27:58 |
36:35 |
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
CR Motor |
|
|
8:44 |
1:00 |
9:44 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR Driven Pulley Assy |
|
|
3:49 |
3:07 |
6:56 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Main Frame Assy |
|
|
7:15 |
11:16 |
18:31 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Paper GuideUpper Assy |
|
|
9:20 |
7:21 |
16:41 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR Unit |
|
|
12:52 |
9:52 |
22:44 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR Timing Belt |
|
|
12:31 |
0:40 |
13:11 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR Encoder Sensor |
|
|
13:13 |
--- |
13:13 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Head FFC |
|
|
14:19 |
--- |
14:19 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FFC Holder |
|
|
13:51 |
--- |
13:51 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frame Base Assy |
|
|
8:07 |
8:51 |
16:58 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pump Unit |
|
|
9:53 |
--- |
9:53 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PF Grounding Spring |
|
|
10:12 |
--- |
10:12 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Spur Gear 16.5 |
|
|
10:21 |
--- |
10:21 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PF Roller Unit |
|
|
13:11 |
5:51 |
19:02 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PF Motor Assy |
|
|
11:43 |
1:08 |
12:51 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frame Base |
|
|
11:43 |
6:53 |
18:36 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tube Cover |
|
|
0:22 |
--- |
0:22 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ink Supply Tank Assy |
|
|
4:57 |
--- |
4:57 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Top Cover |
|
|
0:10 |
--- |
0:10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cap Tank |
|
|
0:22 |
--- |
0:22 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Bottom Cover |
|
|
1:44 |
--- |
1:44 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cover Tube Tank |
|
|
0:55 |
--- |
0:55 |
|
|
|
|
|
Guide Tube Tank |
|
|
1:06 |
--- |
1:06 |
|
|
|
|
|
Left Cover |
|
|
2:34 |
--- |
2:34 |
|
|
|
|
|
Right Cover |
|
|
2:07 |
--- |
2:07 |
|
|
|
|
|
Cover Joint |
|
|
2:39 |
--- |
2:39 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ink Supply Tank (Magenta) |
|
|
4:11 |
--- |
4:11 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ink Supply Tank (Yellow) |
|
|
4:11 |
--- |
4:11 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disassembly/Reassembly |
Overview |
|
|
23 |
|
||||
|
|
|
|
|
|
|
|
|
|
|
Confidential
L365/L366,L360/L362,L310/L312,L220/L222,L130/L132 Series |
|
Revision A |
||||
|
|
Table 2-1. Standard Operation Time |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Time (mm:ss) |
|
|
|
Parts/Unit |
|
|
Adjustment/ |
|
|
|
|
Replacement |
Total |
|
||
|
|
|
|
|||
|
|
|
inspection |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ink Supply Tank (Cyan) |
|
4:11 |
--- |
4:11 |
|
|
Ink Supply Tank (Black) |
|
4:11 |
--- |
4:11 |
|
|
Ink Supply Tank Tube Assy |
|
3:30 |
--- |
3:30 |
|
|
|
|
|
|
|
|
|
Tube Guide Sheet Sub |
|
0:30 |
--- |
0:30 |
|
|
|
|
|
|
|
|
|
Tube Pressing Plate |
|
0:52 |
--- |
0:52 |
|
|
|
|
|
|
|
|
|
Ink Supply Tube Guide 1st |
|
0:06 |
--- |
0:06 |
|
|
|
|
|
|
|
|
|
Ink Supply Tube Guide 2nd |
|
3:25 |
--- |
3:25 |
|
|
|
|
|
|
|
|
|
Joint |
|
2:20 |
--- |
2:20 |
|
|
|
|
|
|
|
|
|
Adapter Cover |
|
0:37 |
--- |
0:37 |
|
|
|
|
|
|
|
|
|
Ink Supply Tube Assy |
|
2:11 |
--- |
2:11 |
|
|
|
|
|
|
|
|
|
Tube Guide Sheet |
|
1:39 |
--- |
1:39 |
|
|
|
|
|
|
|
|
|
Adapter |
|
1:49 |
--- |
1:49 |
|
|
|
|
|
|
|
|
Disassembly/Reassembly |
Overview |
24 |
Confidential