MegaPixel IP Camera
Type numbers NWC-0700, NWC-0800, NWC-0900
en Manual_en
MegaPixel IP Cameras | en |
1 |
|
|
Table of Contents
1 |
Safety |
3 |
1.1 |
Important safety instructions |
3 |
1.2 |
Safety precautions |
5 |
1.3 |
Important notices |
5 |
2 |
Introduction |
9 |
2.1 |
Product information |
9 |
2.2 |
System requirements |
9 |
2.3 |
Network switch or router |
10 |
3 |
Camera reference |
12 |
3.1 |
Introduction |
12 |
3.2 |
Connectors |
13 |
3.3 |
Housing and mounting |
13 |
3.4 |
Network cabling |
14 |
3.5 |
Optics |
14 |
3.5.1 |
Using manual iris lenses |
14 |
3.5.2 |
Auto-iris lenses |
14 |
3.5.3 |
Using auto-iris lenses |
14 |
3.6 |
Accessing cameras |
15 |
3.6.1 |
Supported network services |
15 |
4 |
Software |
16 |
4.1 |
Software installation |
16 |
4.1.1 |
Configure firewall |
17 |
4.1.2 |
Bosch Application Manager |
17 |
4.1.3 |
Camera installer |
18 |
4.1.4 |
Installation tips |
20 |
4.1.4 |
Assigning IP addresses |
20 |
4.1.4 |
Subnets |
20 |
4.1.4 |
Keeping a log of MAC addresses |
20 |
4.2 |
Operating Bosch Video System |
21 |
Bosch Security Systems |
User Manual |
F.01U.064.422 | V 1.0 | 2007.03 |
2 en | |
|
MegaPixel IP Cameras |
|
|
|
4.2.1 |
Toolbar |
21 |
4.2.2 |
Selecting full/reduced resolution and zoom |
23 |
4.2.2 |
Selecting Cameras |
23 |
4.2.2 |
Full/Half camera resolution |
23 |
4.2.2 |
Full size/Reduced size display |
23 |
4.2.2 |
Zooming |
23 |
4.2.3 |
Settings |
24 |
4.2.4 |
Exposure |
25 |
4.2.5 |
Image Quality |
26 |
4.2.6 |
Archive |
28 |
4.2.7 |
Motion Detection |
28 |
4.2.8 |
Save to |
31 |
4.2.9 |
Advanced |
32 |
4.2.10 |
Permission |
33 |
4.2.11 |
Remote Viewing |
33 |
4.2.12 |
Day/Night |
34 |
4.2.13 |
Auto-Iris |
34 |
4.2.14 |
Right-click menu |
35 |
4.2.15 |
User authentication |
37 |
4.2.16 |
Language selection |
37 |
4.2.17 |
Browsing archives |
37 |
4.2.18 |
AVI Maker |
37 |
4.2.19 |
HTTP access |
38 |
4.2.20 |
Firmware Loader - Upgrading the cameras |
38 |
4.3 |
DiBos8 set-up for Bosch Megapixel cameras |
38 |
4.3.1 |
Preparing Megapixel cameras for DiBos8 |
38 |
4.3.2 |
Setting up DiBos8 for Megapixel Cameras |
39 |
4.3.3 |
HTTP command string parameters |
40 |
4.3.3 |
x0 and y0 |
40 |
4.3.3 |
x1 and y1 |
40 |
F.01U.064.422 | V 1.0 | 2007.03 |
User Manual |
Bosch Security Systems |
MegaPixel IP CamerasSafety | en |
3 |
|
|
1 Safety
1.1Important safety instructions
Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit.
1.Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol cleaners.
2.Heat Sources - Do not install the unit near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.
3.Water - Do not use this unit near water, for example near a bathtub, washbowl, sink, laundry basket, in a damp or wet basement, near a swimming pool, in an outdoor installation, or in any area classified as a wet location. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture.
4.Object and liquid entry - Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled with liquids, such as vases or cups, on the unit.
5.Lightning - For added protection during a lightning storm, or when leaving this unit unattended and unused for long periods, unplug the unit from the wall outlet and disconnect the cable system. This will prevent damage to the unit from lightning and power line surges.
6.Controls adjustment - Adjust only those controls specified in the operating instructions. Improper adjustment of other controls may cause damage to the unit. Use of controls or adjustments, or performance of procedures other than those specified, may result in hazardous radiation exposure.
7.Overloading - Do not overload outlets and extension cords. This can cause fire or electrical shock.
8.Power cord and plug protection - Protect the plug and power cord from foot traffic, being pinched by items placed upon or against them at electrical outlets, and its exit from the unit.
9.Power disconnect - Units with or without ON/OFF switches have power supplied to the unit whenever the power cord is inserted into the power source; however, the unit is operational only when the ON/OFF switch is in the ON position. The power cord is the main power disconnect device for switching off the voltage for all units.
Bosch Security Systems |
User Manual |
F.01U.064.422 | V 1.0 | 2007.03 |
4 en | Safety |
MegaPixel IP Cameras |
|
|
10.Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit.
–For external power supplied units, use only the recommended or approved power supplies.
–For limited power source units, this power source must comply with EN60950. Substitutions may damage the unit or cause fire or shock.
–For 9-12 VDC units, voltage applied to the unit's power input should not exceed 12.3 VDC. User-supplied wiring must comply with local electrical codes (Class 2 power levels). Do not ground the supply at the terminals or at the unit's power supply terminals.
–If unsure of the type of power supply to use, contact your dealer or local power company.
11.Servicing - Do not attempt to service this unit yourself. Opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
12.Damage requiring service - Unplug the unit from the main AC power source and refer servicing to qualified service personnel when any damage to the equipment has occurred, such as:
–the power supply cord or plug is damaged;
–exposure to moisture, water, and/or inclement weather (rain, snow, etc.);
–liquid has been spilled in or on the equipment;
–an object has fallen into the unit;
–unit has been dropped or the unit cabinet is damaged;
–unit exhibits a distinct change in performance;
–unit does not operate normally when the user correctly follows the operating instructions.
13.Replacement parts - Be sure the service technician uses replacement parts specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized substitutions may cause fire, electrical shock, or other hazards.
14.Safety check - Safety checks should be performed upon completion of service or repairs to the unit to ensure proper operating condition.
15.Installation - Install in accordance with the manufacturer's instructions and in accordance with applicable local codes.
16.Attachments, changes or modifications - Only use attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the warrantee
F.01U.064.422 | V 1.0 | 2007.03 |
User Manual |
Bosch Security Systems |
MegaPixel IP CamerasSafety | en |
5 |
|
|
or, in the case of an authorization agreement, authority to operate the equipment.
1.2Safety precautions
DANGER! High risk:
This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death.
WARNING! Medium risk:
!Indicates a potentially hazardous situation.
If not avoided, this could result in serious bodily injury or death.
CAUTION! Medium risk:
!Indicates a potentially hazardous situation. If not avoided, this may result in minor or moderate injury. Alerts the user to important instructions accompanying the unit.
CAUTION!
Indicates a potentially hazardous situation.
If not avoided, this may result in property damage or risk of damage to the unit.
NOTICE!
i This symbol indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property.
1.3Important notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over. Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to overturn. Mount the unit per the manufacturer's instructions.
Camera lens - A camera lens must comply and be tested in accordance with UL/IEC60950. Any output or signal lines from the camera must be SELV or Limited Power Source. For safety reasons the environmental specification of the camera lens assembly must be within the environmental specification of -10 °C (14 °F) to 50 °C (122 °F).
Bosch Security Systems |
User Manual |
F.01U.064.422 | V 1.0 | 2007.03 |
6 en | Safety |
MegaPixel IP Cameras |
|
|
Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products. Please dispose of these units at an environmentally compatible recycling facility, per European Directive 2002/96/EC.
Environmental statement - Bosch has a strong commitment towards the environment. This unit has been designed to respect the environment as much as possible.
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.
Power disconnect - Units have power supplied whenever the power cord is inserted into the power source. The power cord is the main power disconnect for all units.
Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights.
Warning - This device is intended for use in public areas only. U.S. federal law strictly prohibits surreptitious recording of oral communications.
|
NOTICE! |
i |
This is a class A product. In a domestic environment this |
product may cause radio interference, in which case the user |
|
|
may be required to take adequate measures. |
|
|
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
–this device may not cause harmful interference, and
–this device must accept any interference received, including interference that may cause undesired operation.
F.01U.064.422 | V 1.0 | 2007.03 |
User Manual |
Bosch Security Systems |
MegaPixel IP CamerasSafety | en |
7 |
|
|
NOTICE!
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-
i ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible for compliance, shall not be made. Any such modifications could void the user's authority to operate the equipment. If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
Disclaimer
Underwriter Laboratories Inc. ("UL") has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested fire, shock and/or casualty hazards as outlined in UL's Standard(s) for Safety for Information Technology Equipment, UL 60950-1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.
Bosch Security Systems |
User Manual |
F.01U.064.422 | V 1.0 | 2007.03 |
8 en | Safety |
MegaPixel IP Cameras |
|
|
NOTICE!
This user guide has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing. The ongoing
i development of the products may mean that the content of the user guide can change without notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between the user guide and the product described.
More Information
For additional information, please contact the Bosch Security Systems location nearest you or visit our web site at www.boschsecuritysystems.com
F.01U.064.422 | V 1.0 | 2007.03 |
User Manual |
Bosch Security Systems |
MegaPixel IP CamerasIntroduction | en |
9 |
|
|
2 Introduction
Bosch MegaPixel® video cameras are state-of-the-art IP units designed to deliver full-motion, high definition digital video across local area networks. The DiBos software system accommodates multiple cameras connected to a single video server and provides a variety of display and digital archiving modes. Delivering over 45 Mpixels/sec of crystal-clear imagery, Bosch MegaPixel cameras represent a superior alternative to low resolution analog and digital video. To accommodate this level of performance certain minimum system requirements have to be met. Please make sure to read this entire manual and to follow the installation instructions given below. For DiBos8 insallation and operation details, refer to its instructions and manuals.
2.1Product information
Contact Bosch Security Systems:
–On the web at http://www.boschsecurity.com/
–By post, e-mail, or phone/fax: from the above mentioned webpage click contact, select Security Systems from the drop down menu and scroll down for your region.
2.2System requirements
The DiBos8 digital video recorder system is the primary viewer and recording system for the Megapixel cameras. In the DiBos8 dongle, the "Network Cameras" must be enabled. Sufficient disk space should be available for the Megapixel cameras files. File size is approximately 200 Kbytes per image.
Camera setup and verification is best done using a dedicated PC with Windows 2000 or Windows XP operating system and running the supplied Bosch Video System.
Personal Computer:
The suggested minimum computer requirements are as follows:
A PC (or laptop) for setup and verification.
–CPU: 1.4 GHz
–RAM: 512 MB
–Video Card: 1024X768, 64 MB RAM
–Network card: 100 base-T
Standard Performance, with live viewing of 16-17 FPS (frames per second) of full-resolution video:
Bosch Security Systems |
User Manual |
F.01U.064.422 | V 1.0 | 2007.03 |
10 en | Introduction |
MegaPixel IP Cameras |
|
|
–CPU: 3.0 GHz
–RAM: 512 MB
–Video Card: 1600x1200, 64 MB RAM
–Network card: 100 base-T
High performance, with best frame rate live viewing:
–CPU: Dual CPU or DualCore 3.2 GHz
–RAM: 1 GB
–Video card: 1920x1200, 128 MB RAM (for NWC-0800 resolution)
–Network card: 100 base-T, 2 network cards - one for cameras and one for other network functions
Monitors, for full resolution live viewing:
–24-inch Wide Aspect Flat Panel LCD Monitor with Height Adjustable Stand (1920x1200 Resolution)
–24 Inch LCD Display (1920 x 1200 resolution)
For Setup and verification:
–Standard PC monitors can be used, images are automatically scaled to the correct size.
2.3Network switch or router
Using a 100 Mbps network switch or router is recommended. Simple hubs do not provide collision management and are not suitable for a multi-camera audio/video system. Suggested models:
Power-over-Ethernet routers:
–"Netgear ProSafe 8PT 100Base-TX Switch with PoE #FS108PNA
10/100Base-TX w/4 PoE 100Base-TX
–"Netgear ProSave 16PT 100Base-TX Switch with PoE #FS116P
10/100Base-TX w/8 PoE 100Base-TX
–"Netgear ProSafe 24+2 Gigabit Switch with PoE 1 Gigabit output w/12 PoE 100Base-TX (www.netgear.com)
–"D-Link Web Smart #DES-1316 (POE Switch/Hub)
F.01U.064.422 | V 1.0 | 2007.03 |
User Manual |
Bosch Security Systems |
MegaPixel IP CamerasIntroduction | en |
11 |
|
|
www.dlink.com 10/100Base-TX
8 PoE ports and 8 non-PoE ports True IEEE 802.3af
–"TRENDnet #TPE-S88 (POE Switch/Hub) www.trendnet.com
10/100Base-TX
8 PoE ports and 8 non-PoE ports True IEEE 802.3af
–"PowerDsine #PD-6001/AC (PoE Single port hub) www.powerdsine.com
10/100Base-TX
Single Midspan POE port True IEEE 802.3af
NOTICE!
i PoE network equipment must be CE marked for use in European Community. Note that the cameras are designed for use with indoor network cabling only.
Bosch Security Systems |
User Manual |
F.01U.064.422 | V 1.0 | 2007.03 |
12 en | Camera reference |
MegaPixel IP Cameras |
|
|
3 Camera reference
3.1Introduction
NWC-0700, NWC-0800 and NWC-0900 are megapixel resolution IP cameras capable of delivering crisp, low-noise images at a video frame rate.
NWC-0700 is a 2-megapixel resolution camera having maximum resolution of 1600 by 1200 and achieving a maximum frame rate of 24.
NWC-0800 is a 3.1-megapixel resolution camera having maximum resolution of 2048 by 1536. It is typically viewed at 1920 by 1200 resolution with the frame rate up to 20.
NWC-0900 is a dual-sensor, day-night camera featuring a 3.1- megapixel color sensor paired with a 1.3-megapixel monochrome sensor sensitive to near infrared illumination. When the scene is well illuminated, the 3.1-megapixel sensor is selected to deliver color images of up to 2048x1536 pixels. To provide seamless transition between day and night modes, the color sensor is set to default resolution of 1920x1200 pixels. In lowlight conditions, NWC-0900 can automatically switch to the 1.3- megapixel (1280x1024) monochrome sensor, enabling the delivery of clear imagery at illumination levels as low as 0.01 lux. NWC-0900 typically delivers 20 fps in day mode and over 30 fps in night mode.
All cameras are equipped with LAN connector and can deliver image data at a maximum data rate of up to 55 Mbps. Images are sent over the network in a compressed Motion JPEG format using TFTP protocol with the supplied software or using HTTP protocol with DiBos8.
Power for all cameras can be supplied via DC jack (+9 V to +12 V) or Power over Ethernet.
CAUTION! Medium risk:
!Never supply power via the Ethernet connection (PoE) when power is already supplied via the power connector.
All cameras feature:
–Automatic exposure (AE) and Gain (AGC) control
–Automatic backlight compensation
–Automatic multi-matrix white balance
–50/60 Hz selectable flicker control
–Electronic pan, tilt, and zoom (PTZ)
F.01U.064.422 | V 1.0 | 2007.03 |
User Manual |
Bosch Security Systems |