INSTALLATION INSTRUCTIONS
EX14/14N
All Environment Camera
MAN-14-04
IMPORTANT SAFETY INSTRUCTIONS
1.Read these instructions.
2.Keep this instruction.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with manufacturer instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in a way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
IMPORTANT
For best results, please read this Instruction Booklet prior to installing the EX14 camera.
WARNING!
CSA Certified / UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety standards.
EU Directives covered by this declaration: 72/9/EC Low Voltage Directives
89/336/EEC Electromagnetic Compatibility Directive
Only qualified personnel shall install any surveillance product.
Bosch Security Systems, Inc. will not be responsible for injuries or damages resulting from the
improper installation or use of any product sold by Bosch Security Systems, Inc their agents,
distributors or dealers.
NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. As part of its’ normal operation this device can generate radio frequency energy and if not installed and used in accordance with the installation manual may cause interference to radio communications. However, there is no guarantee that interference will not occur on a particular installation. If the device does cause interference to radio or television reception the user is encouraged to try to correct the interference by one or more of the following measures:
1)Fit Ferrite beads on all cable to and from the power supply box, within the box walls.
2)Route the composite cable between the camera and the power supply in steel conduit piping over the entire run of the cable up to and including connection to a deep conduit base fitted under the camera and a conduit fitting adaptor in the wall of the PSU box.
3)Contact BOSCH Service Center for further advice.
|
INDEX – EX14/14N |
|
|
|
Page |
Description................................................... |
1 |
|
Unpacking.................................................... |
2 |
|
Parts List...................................................... |
|
2 |
Items Required for Installation..................... |
2 |
|
Initial Preparations....................................... |
3 |
|
Guidelines.................................................... |
3 |
|
Section 1. Camera Mounting ....................... |
4 |
|
Section 2. Camera I/O Connections............ |
9 |
|
Section 3. Input Power Connections………10 |
||
Section 4. |
Camera/LED Adjustments........ |
12 |
Section 5. |
Troubleshooting Guide ............. |
15 |
Section 6. |
General Specifications.............. |
18 |
DESCRIPTION
The EX14 All Environment Camera consists of a twopiece injection molded watertight housing with a tough polycarbonate viewing window. This compact camera meets IP66 ratings for applications wherever environmentally sealed CCD cameras are required. The camera is especially suited for wash down applications in food processing and industrial clean-room installations.
The EX14 can be ordered in monochrome or color versions, featuring varifocal and auto-iris IR-optimized lenses. A rigid nylon mounting bracket is also included with the camera.
A voltage regulator circuit allows for 12V dc or 24V ac operation and a range in between. It also provides protection from voltage surge, transient spikes, and reverse voltage.
The EX14N comes with integrated Infra-Red illumination to permit imaging in 0 Lux conditions
The EX14 is available in several models to meet individual requirements or specific needs.
See the Light. Get the Picture.™
1
UNPACKING
Care should be taken when unpacking the shipped unit. Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit.
Contact BOSCH Service Center if a problem is noted, see the rear page of this booklet for contact numbers.
PARTS LIST (items supplied with unit)
•EX14 Camera or EX14N integrated infraRed
•Two Allen Keys
•One Mounting Bolt
•Nylon Mounting Bracket(supplied with camera)
•Installation Instructions booklet
ITEMS REQUIRED FOR INSTALLATION
(not supplied with unit)
•mounting hardware & tools
2
INITIAL PREPARATIONS
•The camera’s voltage regulator board (VRB) accepts an input voltage of either 12Vdc or 24Vac, and a range in-between, from a regulated power supply.
•The VRB automatically switches between ac or dc inputs, therefore no internal wiring changes are necessary to accommodate these input voltages.
•Determine the optimum location for the camera.
Section 1: Camera Mounting
•All cameras have been tested prior to shipment.
GUIDELINES
The installation of the EX14 Camera is shown in Sections 1 to 4 listed below.
It is important that these steps are followed in sequence:
1.Camera Mounting
2.Camera I/O Connections
3.Input Power Connections
4.Camera/LED Array Adjustments
3
Loading...