TravelPilot Navigation Radio/CD
TravelPilot DX-R52 / DX-R5
Installation instructions
http://www.blaupunkt.com
Installation instructions
Safety instructions
When carrying out installation work and making connections please observe the following safety instructions:
-Disconnect the negative terminal of the battery! When doing so, please observe the vehicle manufacturer’s safety instructions.
-Make sure you do not damage vehicle components when drilling any holes.
-The cross sections of the positive and negative cables must not be less than 1.5 mm2.
-Incorrect installation may cause interference with electronic vehicle systems or your car radio.
-Do not connect the vehicle’s plug connectors to the radio!
-You can obtain the adapter cable required for your vehicle type from any BLAUPUNKT dealer.
-Depending on the model, your vehicle may differ from the description provided here. We accept no responsibility for any damages due to incorrect installation or connection or for any consequential damages.
If the information provided here is not suitable for your specific installation requirements, please contact your Blaupunkt dealer, your vehicle manufacturer or our telephone hotline.
–The TravelPilot can be used in vehicles with:
•10,5-14,4 V battery power
•Negative pole on the chassisInfor mation on proper functioning
To ensure that the TravelPilot functions properly, it is essential that the system be calibrated after it has been completely installed (see Operating instructions / Contents / Calibration).
The system determines the distance travelled via its connection to the vehicle speedometer signal. If there is no speedometer signal, it will be necessary to have a route sensor mounted by an authorised customer service centre.
In this case you will have to order a sensor kit (route sensor, magnet strip, bracket and plug) from your dealer.
Order-No.: 7 607 611 093
256
1. Power supply
1.1Connection to the vehicle ISO standard plug
To prevent electrical malfunctions in vehicle ISO plugs, you have to use the universal ISO adapter cable (OrderNo. 7 607 621 126) (see Fig. 1).
The following vehicles with ISO standard connections can currently be fitted with the universal ISO adapter cable: Alfa Romeo, Citroen, Fiat, Honda, Lancia, Mercedes, Peugeot, Porsche, Renault, Skoda.
For other vehicles with vehicle ISO plugs, use the vehicle-specific ISO adapter cables, e.g. for Audi, Skoda, VW with active antennas (Order-No. 7 607 621 129) (see Fig. 2).
1.2Power connection to vehiclespecific plugs
If the radio connection in your vehicle was fitted with a 10A fuse at the factory (see operating instructions or the fuse box in your car.), you will still need the vehicle-specific adapter cable
(see Fig. 3).
2. Connecting the speakers
2.1Connecting the speakers to the ISO standard plug
In vehicles pre-equipped with passive speakers (with 4-ohm speakers) you can adapt the ISO plug in the vehicle. If necessary, the ISO cable (Order-No.7 607 647 093) can bd¯]sed for extra length (see Fig. 4). Order special adapter cables from your dealer for vehicles pre-equipped with active speakers.
3. Installing the antenna
Connect the antenna wiring to the enclosed bracket (see Fig. 5).
3.1Radio antenna
In pre-equipped vehicles (e.g.: VW, Seat, Audi), the antenna gets its power supply via the antenna wire (see the vehicle operating instructions). If you want to replace the OEM radio with a conventional radio, you will have to order an antenna supply diplexer (Or- der-No. 7 691 290 202) or the adapter cable (Order-No. 7 607 621 129) from your dealer. You will find information on the installation and connection of
the antenna in the antenna installation instructions. (see Fig. 5).
3.2GPS antenna (satellite navigation)
You will find information on how to install the antenna in the enclosed antenna installation instructions.
If the GPS antenna is installed inside the vehicle, we cannot guarantee that the system will function correctly.
4. Installing the TravelPilot
4.1Setting the Gyro
Important: Before the TravelPilot is inserted, the gyroscope must be put in a horizontal position (see Fig. 8).
Important: Installation position of the TravelPilot: right / left: min. -5˚/ max. +5˚, front to back: min. -10˚ / max. +30˚
The TravelPilot is installed in the standard car radio compartment provided by the manufacturer (see Fig. 6 ).
For vehicles without a DIN compartment, Blaupunkt offers vehicle-specif- ic installation kits for 50/52 mm units for the most popular vehicle models. Please check the installation conditions in your vehicle and use a vehi- cle-specific installation kit if necessary.
4.2Installing the bracket
The bracket included with this TravelPilot allows you to install the system in vehicles with a DIN car radio compartment measuring 182 x 53 x165 mm and an instrument panel which is 1 to 20 mm in the area where the fastener tabs are located, (see Fig. 6). For the installation, you have to push the bracket into the compartment and determine which fastener tabs you can bend over with a screwdriver (see Fig. 6a).
Note: Bend over as many of the fastener tabs as possible.
4.3Installing the TravelPilot
Push all of the plugs into the sockets until they lock into place. Now insert the navigation system from the front into the bracket. Apply gentle pressure to both side edges and push it in until the spring locks snap into position on the right and left (you will hear a loud click).
Important! When you push in the system, make sure that you do not put any pressure on the display, the knobs or the keys!
ENGLISH PORTUGUÊS ESPAÑOL
257
Loading...