Beko WMB 81231 User manual

WMB 81231

Washing Machine

User’s Manual

Перална машина

Ръководство за употреба

Plně automatická pračka

Uživatel Manuální

Perilica rublja

Korisnički priručnik

Document Number

2820522427_EN / 16-08-12.(17:52)

1 Important instructions for safety and environment

This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.

1.1 General safety

•This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone.

•Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat.This will cause problems with your product.

•If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent.

There is the risk of electric shock!

•This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.

•Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the grounding

installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

•The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.

•Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.

•Do not force open the locked loading door.The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.

•Unplug the product when not in use.

•Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!

•Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.

•Use detergents, softeners and supplements suitable for automatic washing machines only.

•Follow the instructions on the textile tags and on the detergent package.

•The product must be unplugged during installation, maintenance, cleaning and repairing procedures.

•Always have the installation and repairing procedures carried out by the Authorized Service Agent.

Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

•If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified

person (preferably an electrician) or someone designated by the importer in order to avoid possible risks.

1.2 Intended use

•This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.

•The product must only be used for washing and rinsing of laundry that are marked accordingly.

•The manufacturer waives any responsibility arisen from incorrect usage or transportation.

1.3 Children's safety

•Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.

•Electrical products are dangerous for the children.Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product.

•Do not forget to close the loading door when leaving the room where the product is located.

•Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.

1.4 Package information

•Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

1.5 Disposing of the waste product

•This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling.Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product.

1.6 Compliance with WEEE Directive

This appliance’s packaging material is

recyclable. Help recycle it and protect the environment by dropping it off in the municipal

receptacles provided for this purpose. Your appliance also contains a great amount of

recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste.This way, the appliance recycling

organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

2 / 71 EN	Washing Machine / User’s Manual

2 Installation

Refer to the nearest Authorised Service Agent for installation of the product.To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

C Preparation of the location and electrical,tap water and waste water installations at the place of installation is under customer's responsibility.

B warning: Installation and electrical connections of the product must be carried out by theAuthorized ServiceAgent.Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

A warning: Prior to installation,visually check if the product has any defects on it.If so,do not have it installed. Damaged products cause risks for your safety.

C Make sure that the water inlet and discharge hoses as well as the power cable are not folded,pinched or crushed while pushing the product into its place after installation or cleaning procedures.

2.1 Appropriate installation location

•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

•Total weight of the washing machine and the dryer -with full loadwhen they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

•Do not place the product on the power cable.

•Do not install the product at places where temperature may fall below 0ºC.

•Place the product at least 1 cm away from the edges of other furniture.

2.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

2.Remove transportation safety bolts by turning them gently.

3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

C Never move the product without the transportation safety bolts properly fixed in place!

2.4 Connecting water supply

C The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa).It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly.

Attach a pressure reducing valve if water pressure is higher.

C If you are going to use the double water-inlet product as a single (cold) water-inlet unit,you must install the supplied stopper to the hot water valve before operating the product.(Applies for the products supplied with a blind stopper group.)

A warning: Models with a single water inlet should not be connected to the hot water tap.In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

A warning: Do not use old or used water inlet hoses on the new product.It may cause stains on your laundry.

1.Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90

ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.

2.3 Removing the transportation locks

Awarning: Do not remove the transportation locks before taking out the packaging reinforcement.

Awarning: Remove the transportation safety bolts before operating the washing machine! Otherwise,the product will be damaged.

1.Loosen all the bolts with a suitable spanner until they rotate freely (C).

Awarning: Ensure that the cold and hot water connections are made correctly when installing the product.

Otherwise,your laundry will come out hot at the end of the washing process and wear out.

2.Tighten all hose nuts by hand.Never use a tool when tightening the nuts.

3.Open the taps completely after making the hose connection to check for water leaks at the connection

3 / 71 EN

Washing Machine / User’s Manual

points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

2.5 Connecting to the drain

•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

Awarning: Your house will be flooded if the hose comes out of its housing during water discharge.Moreover,there is risk of scalding due to high washing temperatures!

To prevent such situations and to ensure smooth water intake and discharge of the machine,fix the end of the discharge hose tightly so that it cannot come out.

•The hose should be attached to a height of at least 40 cm, and 100 cm at most.

•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet.Therefore, follow the heights described in the figure.

•To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.

•The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.

•If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m.To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

2.6 Adjusting the feet

Awarning: In order to ensure that the product operates more silently and vibration-free,it must stand level and balanced on its feet.Balance the machine by adjusting the feet.Otherwise,the product may move from its place and cause crushing and vibration problems.

1.Loosen the lock nuts on the feet by hand.

2.Adjust the feet until the product stands level and balanced.

3.Tighten all lock nuts again by hand.

Awarning: Do not use any tools to loosen the lock nuts. Otherwise,they will get damaged.

2.7 Electrical connection

Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

•Connection must comply with national regulations.

•Power cable plug must be within easy reach after installation.

•If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse.

•The voltage specified in the "Technical specifications" section must be equal to your mains voltage.

•Do not make connections via extension cables or multiplugs.

Bwarning: Damaged power cables must be replaced by theAuthorized ServiceAgents.

Transportation of the product

1.Unplug the product before transporting it.

2.Remove water drain and water supply connections.

3.Drain all water that has remained in the product.

4.Install transportation safety bolts in the reverse order of removal procedure;

C Never move the product without the transportation safety bolts properly fixed in place!

Awarning: Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.

4 / 71 EN	Washing Machine / User’s Manual

3 Preparation

3.1 Sorting the laundry

•Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.

•Always obey the instructions given on the garment tags.

3.2 Preparing laundry for washing

•Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.

•Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.

•Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.

•Place curtains in without compressing them. Remove curtain attachment items.

•Fasten zippers, sew loose buttons and mend rips and tears.

•Wash “machine washable” or “hand washable” labeled products only with an appropriate programme.

•Do not wash colours and whites together.New, dark coloured cottons release a lot of dye.Wash them separately.

•Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.

•Use only dyes/colour changers and limescale removers suitable for machine wash.Always follow the instructions on the package.

•Wash trousers and delicate laundry turned inside out.

•Keep laundry items made of Angora wool in the freezer for a few hours before washing.This will reduce pilling.

•Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.

3.3 Things to be done for energy saving

Following information will help you use the product in an ecological and energy-efficient manner.

•Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and consumption table".

•Always follow the instructions on the detergent packaging.

•Wash slightly soiled laundry at low temperatures.

•Use faster programmes for small quantities of lightly soiled laundry.

•Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.

•If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process.

•Do not use detergent in excess of the amount recommended on the detergent package.

3.4 Initial use

Before starting to use the product, make sure that all preparations are made in accordance with the instructions in sections “Important safety instructions” and “Installation”. To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If your product

is not equipped with Drum Cleaning programme, perform the Initial Use procedure in accordance with the methods described under “5.2 Cleaning the loading door and the drum” section of the user manual.

C Use an anti-limescale suitable for the washing machines.

Some water might have remained in the product due to C the quality control processes in the production.It is not

harmful for the product.

3.5 Correct load capacity

The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. The machine automatically adjusts the amount of water according to the weight of the loaded laundry.

Awarning: Follow the information in the“Programme and consumption table”.When overloaded,machine's washing performance will drop.Moreover,noise and vibration problems may occur.

Laundry type	Weight (g)
Bathrobe	1200
Napkin	100
Duvet cover	700
Bed Sheet	500
Pillowcase	200
Tablecloth	250
Towel	200
Hand towel	100
Evening gown	200
Underclothing	100
Men’s overalls	600
Men’s shirt	200
Men’s pajamas	500
Blouses	100

3.6 Loading the laundry

1.Open the loading door.

2.Place laundry items loosely into the machine.

3.Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.

5 / 71 EN	Washing Machine / User’s Manual

The loading door is locked while a programme is running.

C Thecomesdoorto canan end.only be opened a while after the programme

Awarning: In case of misplacing the laundry,noise and vibration problems may occur in the machine.

3.7 Using detergent and softener

When using detergent,softener,starch,fabric dye,bleach

C or limescale remover read the manufacturer's instructions on the package carefully and follow the suggested dosage values.Use measuring cup if available.

Detergent Drawer

The detergent drawer is composed of three compartments:

–(1) for prewash

–(2) for main wash

–(3) for softener

–(*) in addition, there is siphon piece in the softener compartment.

2 3 1

Detergent, softener and other cleaning agents

•Add detergent and softener before starting the washing programme.

•Never leave the detergent drawer open while the washing programme is running!

•When using a programme without prewash,do not put any detergent into the prewash compartment

(compartment nr. "1").

•In a programme with prewash,do not put liquid detergent into the prewash compartment (compartment nr. "1").

•Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the machine.

•If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash compartment (compartment nr. "2").

Choosing the detergent type

The type of detergent to be used depends on the type and colour of the fabric.

•Use different detergents for coloured and white laundry.

•Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely for delicate clothes.

•When washing dark coloured clothes and quilts,it is recommended to use liquid detergent.

•Wash woolens with special detergent made specifically for woolens.

Awarning: Use only detergents manufactured specifically for washing machines.

Awarning: Do not use soap powder.

Adjusting detergent amount

The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

•Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.

•Use lesser detergent for small amounts or lightly soiled clothes.

Using softeners

Pour the softener into the softener compartment of the detergent drawer.

•Do not exceed the (>max<) level marking in the softener compartment.

•If the softener has lost its fluidity,dilute it with water before putting it in the detergent drawer.

Using liquid detergents

If the product contains a liquid detergent cup:

•Make sure that you have placed the liquid detergent cup in compartment nr. "2".

•If the liquid detergent has lost its fluidity, dilute it with water before putting in the detergent cup.

If the product does not contain a liquid detergent cup:

•Do not use liquid detergent for the prewash in a programme with prewash.

•Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use the Delayed Start function, do not use liquid detergent.

Using gel and tablet detergent

Apply the following instructions when using tablet, gel and similar detergents.

•If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup, put the gel detergent into the main wash detergent compartment during first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the programme.

•If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum before washing.

•Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the drum before washing.

Tablet detergents may leave residues in the detergent C compartment.If you encounter such a case,place the tablet detergent between the laundry,close to the lower

part of the drum in future washings.

C Use the tablet or gel detergent without selecting the prewash function.

6 / 71 EN	Washing Machine / User’s Manual

Using starch

•Add liquid starch, powder starch or the fabric dye into the softener compartment.

•Do not use softener and starch together in a washing cycle.

•Wipe the inside of the machine with a damp and clean cloth after using starch.

Using bleaches

•Select a programme with prewash and add the bleaching agent at the beginning of the prewash. Do not put detergent in the prewash compartment.As an alternative application, select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step.

•Do not use bleaching agent and detergent by mixing them.

•Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin irritation.

Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes.

•When using oxygen based bleaches, select a programme that washes at a lower temperature.

•Oxygen based bleaches can be used together with detergents; however, if its thickness is not the same with the detergent, put the detergent first into the compartment nr. "2" in the detergent drawer and wait until the detergent flows while the machine is taking in water.Add the bleaching agent from the same compartment while the machine is still taking in water.

Using limescale remover

•When required, use limescale removers manufactured specifically for washing machines only.

3.8 Tips for efficient washing

<![if ! IE]>

<![endif]>Soiling Level

			Clothes
		Light colours and whites	Colours	Dark colours	Delicates/
					Woolens/Silks
		(Recommended temperature	(Recommended temperature	(Recommended	(Recommended
				temperature range	temperature range
		range based on soiling level:	range based on soiling level:
				based on soiling level:	based on soiling level:
		40-90ºC)	cold-40ºC)	cold-40ºC)	cold-30ºC)
		It may be necessary to pre-	Powder and liquid
		treat the stains or perform
			detergents recommended
		prewash.Powder and liquid			Prefer liquid
	Heavily Soiled		for colours can be used at	Liquid detergents
		detergents recommended			detergents produced
			dosages recommended for	suitable for colours
		for whites can be used at			for delicate clothes.
			heavily soiled clothes.It is	and dark colours can
	(difficult stains such	dosages recommended for			Woolen and silk
			recommended to use powder	be used at dosages
		heavily soiled clothes.It is			clothes must be
	as grass,coffee,		detergents to clean clay and	recommended for
		recommended to use powder			washed with special
	fruits and blood.)		soil stains and the stains that	heavily soiled clothes.
		detergents to clean clay and			woolen detergents.
			are sensitive to bleaches.Use
		soil stains and the stains that
		are sensitive to bleaches.	detergents without bleach.
	Normally Soiled		Powder and liquid detergents	Liquid detergents	Prefer liquid
		Powder and liquid detergents			detergents produced
		recommended for whites	recommended for colours	suitable for colours	for delicate clothes.
			can be used at dosages	and dark colours can
	(For example,stains	can be used at dosages			Woolen and silk
			recommended for normally	be used at dosages
	caused by body on	recommended for normally	soiled clothes.Use detergents	recommended for	clothes must be
	collars and cuffs)	soiled clothes.	without bleach.	normally soiled clothes.	washed with special
					woolen detergents.
			Powder and liquid detergents	Liquid detergents	Prefer liquid
	Lightly Soiled	Powder and liquid detergents			detergents produced
			recommended for colours	suitable for colours
		recommended for whites	can be used at dosages	and dark colours can	for delicate clothes.
		can be used at dosages			Woolen and silk
	(No visible stains		recommended for lightly	be used at dosages
		recommended for lightly soiled			clothes must be
			soiled clothes.Use detergents	recommended for lightly
	exist.)	clothes.			washed with special
			without bleach.	soiled clothes.	woolen detergents.

7 / 71 EN	Washing Machine / User’s Manual

4 Operating the product

4.1 Control panel

1

2

3

4

5

	8		7	6
1	- Programme Selection knob (Uppermost position On / Off)	5	- Start / Pause button
2	- Display	6	- Auxiliary Function buttons
3	- Delayed Start button	7	- Spin Speed Adjustment button
4	- Programme Follow-up indicator	8	- Temperature Adjustment button

Dark wash	Dark wash	Synthetics	Cottons	Pre-wash	Main	Rinse	Wash	Spin	Delicate	Pet hair	Door Ready
(Darkcare)	(Darkcare)				wash					removal
Drain	Anti-	Duvet	Child-	Hand	BabyProtect	Cotton	Woollens expres 14		Daily	mini 30	On/Off
(Pump)	creasing	(Bedding) proof lock		Wash		Eco	Super short
							express
Daily	Rinse hold	Start/	No spin	Quick	Finished	Cold	Temperature	Self	Lingerie	Eco Clean
express		Pause		wash				Clean
Mixed 40	Super 40	Extra rinse	Freshen	Shirts	Jeans	Sport	Time delay Intensive		Fasihon	Anti-
(Mix40)		(Rinse Plus) up							care	allergic

8 / 71 EN	Washing Machine / User’s Manual

4.2 Preparing the machine

Make sure that the hoses are connected tightly. Plug in your machine.Turn the tap on completely.Place the laundry in the machine.Add detergent and fabric softener.

4.3 Programme selection

1.Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the "Programme and consumption table" and the temperature table below.

	90˚C	Heavily soiled white cottons and linens.(coffee table
		covers,tableclothes,towels,bed sheets,etc.)
		Normally soiled,coloured,fade proof linens,cottons or
	60˚C	synthetic clothes (shirt,nightgown,pajamas,etc.) and
		lightly soiled white linens (underwear,etc.)
	40˚C-	Blended laundry including delicate textile (veil curtains,
	30˚C-
		etc.),synthetics and woolens.
	Cold

2.Select the desired programme with the Programme Selection button.

C Programmes are limited with the highest spin speed appropriate for that particular type of fabric.

When selecting a programme,always consider the type C oftemperature.fabric,colour,degree of soiling and permissible water

C Always select the lowest required temperature.Higher temperature means higher power consumption.

C For further programme details,see "Programme and consumption table"

4.4 Main programmes

Depending on the type of fabric, use the following main

programmes.

• Cottons

Use this programme for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.).Your laundry will be washed with vigorous

washing action for a longer washing cycle.

• Synthetics

Use this programme to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a gentle action and has a shorter washing cycle compared to the Cottons programme.

For curtains and tulle, use the Synthetic 40˚C programme with prewash and anti-creasing functions selected.As their meshed texture causes excessive foaming, wash the veils/ tulle by putting little amount of detergent into the main wash compartment. Do not put detergent in the prewash

compartment.

• Woollens

Use this programme to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woolens.

4.5 Additional programmes

For special cases, additional programmes are available in the machine.

C Additional programmes may differ according to the model of the machine.

• Cotton Economic

You may wash your normally soiled durable cotton and linen laundry in this programme with the highest energy and water saving compared to all other wash programmes suitable for cottons.Actual water temperature may differ from the declared cycle temperature. Programme duration may automatically be shortened during later stages of the programme if you wash less amount (e.g. ½ capacity or less) of laundry. In this case energy and water consumption will be further decreased giving you the opportunity for a more economical wash.This feature is available for certain

models having remaining time display.

• BabyProtect

Use this programme to wash baby laundry, and the laundry that belongs to allergic persons. Longer heating time and an

additional rinsing step provide a higher level of hygiene.

• Hand wash

Use this programme to wash your woolen/delicate clothes that bear “not machinewashable” tags and for which hand wash is recommended. It washes laundry with a very gentle

washing action to not to damage clothes.

• Daily express

Use this programme to wash your lightly soiled cotton

clothes in a short time.

• Darkwash

Use this programme to wash your dark coloured laundry or the laundry that you do not want it get faded.Washing is performed with little mechanic action and at low temperatures. It is recommended to use liquid detergent or

woolen shampoo for dark coloured laundry.

• Mixed 40 (Mix 40)

Use this programme to wash your cotton and synthetic clothes together without sorting them.

4.6 Special programmes

For specific applications, select any of the following

programmes.

• Rinse

Use this programme when you want to rinse or starch

separately.

• Spin + Drain

Use this programme to apply an additional spin cycle for your laundry or to drain the water in the machine.

Before selecting this programme, select the desired spin speed and press Start / Pause button. First, the machine will drain the water inside of it.Then, it will spin the laundry with the set spin speed and drain the water coming out of them.

If you wish to drain only the water without spinning your laundry, select the Pump+Spin programme and then select the No Spin function with the help of Spin Speed Adjustment button. Press Start / Pause button.

C Use a lower spin speed for delicate laundries.

9 / 71 EN	Washing Machine / User’s Manual

4.7 Temperature selection

Whenever a new programme is selected, the maximum temperature for the selected programme appears on the temperature indicator.

To decrease the temperature, press the Temperature Adjustment button.Temperature will decrease gradually.

If the programme has not reached the heating step,

C you can change the temperature without switching the machine to Pause mode.

4.8 Spin speed selection

Whenever a new programme is selected, the recommended spin speed of the selected programme is displayed on the spin speed indicator.

To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases gradually.Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the display. See "Auxiliary function selection" section for explanations of these options.

If the programme has not reached the spinning step,

C you can change the speed without switching the machine to Pause mode.

10 / 71 EN	Washing Machine / User’s Manual

4.9 Programme and consumption table

EN		2
Programme			<![if ! IE]> <![endif]>(kg)LoadMax.		<![if ! IE]> <![endif]>ConsumptionWater (l)		<![if ! IE]> <![endif]>ConsumptionEnergy (kWh)		<![if ! IE]> <![endif]>Speed***Max.
Cottons			8		80		2.60		1600
	90
Cottons	60		8		80		1.80		1600
Cottons	40		8		80		0.90		1600
Cotton Economic	60**		8		53		1.27		1600
Cotton Economic	60**		4		44		1.07		1600
Cotton Economic	40**		4		44		0.87		1600
Daily express	90		8		70		2.20		1400
Daily express	60		8		70		1.13		1400
Daily express	30		8		70		0.31		1400
Darkwash	40		4		75		0.63		800
Mix40	40		4		60		0.70		800
Hand wash	30		1.5		35		0.18		600
Woollens	40		2		54		0.35		600
BabyProtect	90		8		100		2.60		1600
Synthetics	60		4		60		1.00		800
Synthetics	40		4		60		0.58		800

	Auxiliary functions
						Selectable temperature
		<![if ! IE]> <![endif]>Quick Wash	<![if ! IE]> <![endif]>Rinse Plus	<![if ! IE]> <![endif]>Anti-Creasing	<![if ! IE]> <![endif]>Rinse Hold	range °C
<![if ! IE]> <![endif]>Prewash
•		•	•	•	•	Cold-90
•		•	•	•	•	Cold-90
•		•	•	•	•	Cold-90
					•	40-60
					•	40-60
					•	40-60
			•		•	Cold-90
			•		•	Cold-90
			•		•	Cold-90
			*		•	Cold-40
•		•	•	•	•	Cold-40
						Cold-30
			•		•	Cold-40
•			*		•	30-90
•		•	•	•	•	Cold-60
•		•	•	•	•	Cold-60

• :Selectable

* :Automatically selected,no canceling.

**:Energy Label programme (EN 60456 Ed.3)

***:If maximum spin speed of the machine is lower then this value,you can only select up to the maximum spin speed. - :See the programme description for maximum load.

**“Cotton eco 40°C and Cotton eco 60°C are standard cycles.”These cycles are known as‘40°C cotton standard cycle’ and ‘60°C cotton standard cycle’ and indicated with the symbols on the panel.

C The auxiliary functions in the table may vary according to the model of your machine.

C Water and power consumption may vary subject to the changes in water pressure,water hardness and temperature,ambient temperature,type and amount of laundry,selection of auxiliary functions and spin speed,and changes in electric voltage.

C You can see the washing time of the programme you have selected on the display of the machine.It is normal that small differences may occur between the time shown on the display and the real washing time.

11 / 71 EN	Washing Machine / User’s Manual

4.10 Auxiliary function selection

Select the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running

programme without pressing the Start / Pause button when the machine is operating. For this, the machine must be in a step before the auxiliary function you are going to select or cancel.

If the auxiliary function cannot be selected or canceled, light of the relevant auxiliary function will blink 3 times to warn the user.

Some functions cannot be selected together.If a

C second auxiliary function conflicting with the first one is selected before starting the machine,the function selected first will be canceled and the second auxiliary function selection will remain active.For example,if you want to select QuickWash after you have selected the Prewash,Prewash will be canceled and QuickWash will remain active.

An auxiliary function that is not compatible with the C programme cannot be selected.(See“Programme and

consumption table”)

C Auxiliary Function buttons may vary according to the model of the machine.

• Prewash

A Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy, water, detergent and time.

C Prewash without detergent is recommended for tulle and curtains.

• Quick Wash

This function can be used in Cottons and Synthetics programmes. It decreases the washing times and also the number of rinsing steps for lightly soiled laundry.

When you select this function,load your machine

C with half of the maximum laundry specified in the programme table.

• Rinse Plus

This function enables the machine to make another rinsing in addition to the one already made after the main wash.

Thus, the risk for sensitive skins (babies, allergic skins, etc.) to be effected by the minimal detergent remnants on the

laundry can be reduced.

• Anti-Creasing

This function creases the clothes lesser when they are being washed. Drum movement is reduced and spinning speed is limited to prevent creasing. In addition, washing is done with

a higher water level.

• Rinse Hold

If you are not going to unload your clothes immediately after the programme completes, you may use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled when there is no water in the machine. Press Start / Pause button after this process if you want to drain the water without spinning your laundry.

Programme will resume and complete after draining the water.

If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause button.

The programme resumes.Water is drained, laundry is spun

and the programme is completed.

• Pet hair removal

This function helps to remove pet hair that remain on your garments more effectively.

When you select this function, Prewash and Extra Rinse steps are added to the normal programme.Thus, washing is performed with more water (30%) and the pet hair is removed more effectively.

A Never wash your pets in the washing machine.

Delayed Start

With the Delayed Start function the startup of the programme may be delayed up to 19 hours. Delayed start time can be increased by increments of 1 hour.

C Do not use liquid detergents when you set Delayed Start!There is the risk of staining of the clothes.

Open the loading door, place the laundry and put detergent, etc. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions. Set the desired time by pressing the Delayed Start button. Press Start / Pause button.The delayed start time you have set is displayed. Delayed start countdown starts.“_” symbol next to the delayed start time moves up and down on the display.

C Additional laundry may be loaded during the delayed start period.

At the end of the countdown, duration of the selected programme will be displayed.“_” symbol will disappear and

the selected programme will start.

Changing the Delayed Start period

If you want to change the time during countdown: Press Delayed Start button.Time will increase by 1 hour

each time you press the button. If you want to decrease the delayed start time, press Delayed Start button repeatedly

until the desired delayed start time appears on the display.

Canceling the Delayed Start function

If you want to cancel the delayed start countdown and start the programme immediately:

Set the Delayed Start period to zero or turn the Programme Selection knob to any programme.Thus, Delayed Start function will be canceled.The End/Cancel light flashes continuously. Then, select the programme you want to run again. Press Start / Pause button to start the programme.

4.11 Starting the programme

Press Start / Pause button to start the programme. Programme follow-up light showing the startup of the programme will turn on.

12 / 71 EN	Washing Machine / User’s Manual

If no programme is started or no key is pressed within C 1 minute during programme selection process,the

machine will switch to Pause mode and the illumination level of the temperature,speed and loading door indicator lights will decrease. Other indicator lights and indicators will turn off.Once the Programme Selection knob is rotated or any button is pressed,indicator lights and indicators will turn on again.

4.12 Child Lock

Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid any changes in a running programme.

If the Programme Selection knob is turned when the C Child Lock is active,“Con”appears on the display.

The Child Lock does not allow any change in the programmes and the selected temperature,speed and auxiliary functions.

Even if another programme is selected with the

C Programme Selection knob while the Child Lock is active,previously selected programme will continue running.

To activate the Child Lock:

Press and hold 1st and 2nd Auxiliary Function buttons for

3 seconds. The lights on the 1st and 2nd Auxiliary Function buttons will flash, and "C03", "C02", "C01" will appear on the display respectively while you keep the buttons pressed for 3 seconds.Then, "Con" will appear on the display indicating that the Child Lock is activated. If you press any button or turn the Programme Selection knob when the Child Lock is active, same phrase will appear on the display.The lights on the 1st and 2nd auxiliary function buttons that are used to deactivate the Child Lock will blink 3 times.

To deactivate the Child Lock:

Press and hold 1st and 2nd auxiliary function buttons for 3 seconds while any programme is running. The lights on the 1st and 2nd Auxiliary Function buttons will flash, and "C03", "C02", "C01" will appear on the display respectively while you keep the buttons pressed for 3 seconds.Then, "COFF" will appear on the display indicating that the Child Lock is deactivated.

In addition to the method above,to deactivate the Child C Lock,switch the Programme Selection knob to On /

Off position when no programme is running,and select another programme.

C Child Lock is not deactivated after power failures or when the machine is unplugged.

4.13 Progress of programme

Progress of a running programme can be followed from the Programme Follow-up indicator.At the beginning of every programme step, the relevant indicator light will turn on and light of the completed step will turn off.

You can change the auxiliary functions, speed and temperature settings without stopping the programme flow while the programme is running.To do this, the change you are going to make must be in a step after the running programme step. If the change is not compatible, relevant lights will flash for 3 times.

If the machine does not pass to the spinning step, C Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the

machine.

4.14 Loading door lock

There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable.

Loading door light will start flashing when the machine is switched to Pause mode. Machine checks the level of

the water inside. If the level is suitable, Loading Door light illuminates steadily within 1-2 minutes and the loading door can be opened.

If the level is unsuitable, Loading Door light turns off and the loading door cannot be opened. If you are obliged to open the Loading Door while the Loading Door light is off, you have to cancel the current programme; see "Canceling the programme".

4.15 Changing the selections after programme has started

Switching the machine to pause mode

Press the Start / Pause button to switch the machine to pause mode while a programme is running. The light of the step which the machine is in starts flashing in the

Programme Follow-up indicator to show that the machine has been switched to the pause mode.

Also, when the loading door is ready to be opened, Loading Door light will also illuminate continuously in addition to the

programme step light.

Changing the speed and temperature settings for auxiliary functions

Depending on the step the programme has reached, you may cancel or activate the auxiliary functions; see, "Auxiliary function selection".

You may also change the speed and temperature settings; see, "Spin speed selection" and "Temperature selection".

C	If no change is allowed,the relevant light will flash for
	3 times.

Adding or taking out laundry

Press the Start / Pause button to switch the machine to pause mode. The programme follow-up light of the relevant step during which the machine was switched into the pause mode will flash. Wait until the Loading Door can be opened. Open the Loading Door and add or take out the laundry. Close the Loading Door. Make changes in auxiliary functions, temperature and speed settings if necessary. Press Start / Pause button to start the machine.

4.16 Canceling the programme

To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be canceled. End / Cancel light will flash continuously to notify that the programme has been canceled.

Pump function is activated for 1-2 minutes regardless of the programme step, and whether there is water in the machine or not.After this period, your machine will be ready to start with the first step of the new programme.

13 / 71 EN	Washing Machine / User’s Manual

Depending on the step where the programme was C canceled in,you may have to put detergent and

softener again for the programme you have selected anew.

4.17 End of programme

“End” appears on the display at the end of the programme. Wait until the loading door light illuminates steadily. Press On / Off button to switch off the machine.Take out your laundry and close the loading door. Your machine is ready for the next washing cycle.

5 Maintenance and cleaning

Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.

5.1 Cleaning the detergent drawer

Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time.

1.Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.

If more than normal amount of water and softener C mixture starts to gather in the softener compartment,the

siphon must be cleaned.

2.Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin.Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning.

3.Insert the drawer back into its place after cleaning and make sure that it is seated well.

If your detergent drawer is the one indicated in the following figure:

functions as well. Run theBefore starting the programme, put max. 100 g of powder anti-limescale into the main wash detergent compartment (compartment nr. 2). If the anti-limescale is in tablet form, put only one tablet into compartment nr. 2. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end.

C Repeat Drum Cleaning process in every 2 months.

C Use an anti-limescale suitable for the washing machines.

After every washing make sure that no foreign substance is left in the drum.

If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick.

Foreign metal substances will cause rust stains in the C drum.Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool

or wire wool.

Awarning: Never use sponge or scrub materials.These will damage the painted and plastic surfaces.

5.3 Cleaning the body and control panel

Wipe the body of the machine with soapy water or noncorrosive mild gel detergents as necessary, and dry with a soft cloth.

Use only a soft and damp cloth to clean the control panel.

5.4 Cleaning the water intake filters

There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty.

Lift the rear part of the siphon to remove it as illustrated.

C After performing the above mentioned cleaning procedures,replace the siphon back to its seating and push its front section downwards to make sure that the locking tab engages.

5.2 Cleaning the loading door and the drum

Residues of softener, detergent and dirt may accumulate in your machine in time and may cause unpleasant odours

and washing complaints.To avoid this, use the Drum Cleaning programme. If your machine is not featured with Drum Cleaning programme, use Cottons-90 programme and select Additional Water or Extra Rinse auxiliary

1.Close the taps.

2.Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an

appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.

3.Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.

14 / 71 EN	Washing Machine / User’s Manual

4.Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.

5.5 Draining remaining water and cleaning the pump filter

The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water.Thus, the water will be discharged without any problem and the service life of the pump will extend.

If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months.Water must be drained off first to clean the pump filter.

In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely.

Awarning: Foreign substances left in the pump filter may damage your machine or may cause noise problem.

In order to clean the dirty filter and discharge the water: 1. Unplug the machine to cut off the supply power.

Awarning: Temperature of the water inside the machine may rise up to 90 ºC.To avoid burning risk,filter must be cleaned after the water in the machine cools down.

2.Open the filter cap.

If the filter cap is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself.

If the filter cap is one piece, pull the cap from both sides at the top to open.

You can remove the filter cover by slightly pushing C downwards with a thin plastic tipped tool,through the

gap above the filter cover.Do not use metal tipped tools to remove the cover.

3.Some of our products have emergency draining hose and some does not have. Follow the steps below to discharge the water.

Discharging the water when the product has an emergency draining hose:

a.Pull the emergency draining hose out from its seat

b.Place a large container at the end of the hose. Drain the water into the container by pulling out the plug at the end of the hose.When the container is full, block the inlet

of the hose by replacing the plug.After the container is emptied, repeat the above procedure to drain the water in the machine completely.

c.When draining of water is finished, close the end by the plug again and fix the hose in its place.

d.Turn the pump filter to take it out.

Discharging the water when the product does not have an emergency draining hose:

a.Place a large container in front of the filter to catch water from the filter.

b.Loosen pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter.Always keep a piece of cloth handy to absorb any spilled water.

c.When the water inside the machine is finished, take out

the filter completely by turning it.

4.Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.

5.Install the filter.

6.If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat the tabs in the lower part into their places first, and then press the upper part to close.

15 / 71 EN	Washing Machine / User’s Manual

6 Technical specifications

Models (EN)	WMB 81231
Maximum dry laundry capacity (kg)	8
Height (cm)	84
Width (cm)	60
Depth (cm)	59
Net weight (±4 kg.)	73
Electrical input (V/Hz)	230 V / 50Hz
Total current (A)	10
Total power (W)	2200
Spin speed (rpm max.)	1200
Stand-by mode power (W)	1.35
Off-mode power (W)	0.25
Main model code	928
Single Water inlet / Double Water inlet	• / -

• Available

C Technical specifications may be changed without prior notice to improve the quality of the product.

C Figures in this manual are schematic and may not match the product exactly.

C Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards.Depending on operational and environmental conditions of the product,these values may vary.

16 / 71 EN	Washing Machine / User’s Manual

7 Troubleshooting

Programme cannot be started or selected.

•Washing machine has switched to self protection mode due to a supply problem (line voltage,water pressure,etc.).>>> To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be cancelled. (See “Canceling the programme”)

Water in the machine.

• Some water might have remained in the product due to the quality control processes in the production.>>> This is not a failure; water is not harmful to the machine.

Machine vibrates or makes noise.

•Machine might be standing unbalanced.>>> Adjust the feet to level the machine.

•A hard substance might have entered into the pump filter.>>> Clean the pump filter.

•Transportation safety bolts are not removed.>>> Remove the transportation safety bolts.

•Laundry quantity in the machine might be too little.>>> Add more laundry to the machine.

•Machine might be overloaded with laundry.>>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine.

•Machine might be leaning on a rigid item.>>> Make sure that the machine is not leaning on anything.

Machine stopped shortly after the programme started.

• Machine might have stopped temporarily due to low voltage.>>> It will resume running when the voltage restores to the normal level.

Programme time does not countdown. (On models with display)

•Timer may stop during water intake.>>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this.

•Timer may stop during heating step.>>> Timer indicator will not countdown until the machine reaches the selected temperature.

•Timer may stop during spinning step.>>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.

•Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment.Laundry should be rearranged and re-spun.

Foam is overflowing from the detergent drawer.

•Too much detergent is used.>>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer.

•Put detergent into the machine suitable for the programmes and maximum loads indicated in the“Programme and consumption table”. When you use additional chemicals (stain removers,bleachs and etc),reduce the amount of detergent.

Laundry remains wet at the end of the programme

•Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage.

>>> Use recommended amount of detergent.

•Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment.Laundry should be rearranged and re-spun.

Awarning: If you cannot eliminate the problem although you follow the instructions in this section,consult your dealer or the Authorized ServiceAgent.Never try to repair a nonfunctional product yourself.

17 / 71 EN	Washing Machine / User’s Manual

Номер на документа

2820522427_BG / 16-08-12.(17:04)

1 Важни указания за безопасност и опазване на околната среда

Този раздел съдържа важни указания, които ще ви помогнат да предотвратите риска от нараняване или щети върху имуществото ви. Неспазването на тези указания правят невалидна гаранцията.

1.1 Обща безопасност

•Този продукт може да се ползва от деца над 8 години включително, както и от лица с физически, сензорни или умствени недъзи или необучени и неопитни хора, но само ако те са наглеждани ли обучени от лице, което ги е

инструктирало относно безпасната употреба на уреда и свързаните рискове. Децата не бива да си играят с уреда. Почистването и поддръжката не бива да се извършват от деца, освен ако те не са надзиравани от възрастен.

•Не поставяйте уреда върху покрит с килим под. В противен случай, блокираният приток на въздух отдолу ще доведе до пренагряване на електрическите части на машината. Това може да доведе до проблеми с уреда.

•Ако уредът е повреден, той не бива да се ползва преди да е поправен от представител на оторизиран сервиз. Съществува риск от електрически удар!

•Уредът е програмиран да продължи работа в случай на прекъсване на електрозахранването. Ако желаете да откажете програма, вижте раздел "Отказ на програма".

•Свържете уреда към заземен контакт, защитен с 16-амперов бушон. Не мислете, че не е важно заземяването на инсталацията Ви да е направено от квалифициран електротехник. Фирмата ни не носи отговорност за щети по причина на ползване на уреда без заземяване направено съгласно местните наредби.

•Водопроводът и отточните тръби трябва да са добре затегнати и да не са повредени. В

противен случай съществува риск от протичане.

•Никога не отваряйте вратата на пералнята за да извадите филтъра ако в резервоара има останала вода. В противен случай съществува риск от изгаряне с горещата вода.

•Не насилвайте заключената врата за да я отворите. Вратата е готова за отваряне само няколко минути след завършване на перилния цикъл. Ако насилите вратата за да я отворите, може да повредите вратата и залючващия механизъм.

•Изключете уреда от контакта когато не го ползвате.

•Никога не мийте уреда с изливане или пръскане на вода отгоре му! Съществува риск от електрически удар!

•Никога не пипайте щепсела с мокри ръце! Никога не изваждайте щепсела като дърпате за кабела, винаги хващайте за щепсела.

•Изполвайте прах за пране, омекотител и други препарати, подходящи за автоматична перална машина.

•Следвайте указанията върху етикетите на дрехите и върху опаковката на препарата.

•Уредът трябва да бъде изключен от контакта при монтаж, подрръжка, почистване и ремонт.

•Монтаж и ремонт на уреда трябва да се извършва само от представител на

оторизирания сервиз. Производителят не носи отговорност за щети, причинени от процедури, извършени от неквалифицирани лица.

•Ако захранвашият кабел е повреден, той трябва да бъде подменен от производителя, следпродажбения сервиз или лице с подобна квалификация (за предпочитане електротеник) или друго определено от внсителя лице, с цел да се избегнат всякакви рискове.

1.2 Предназначение на уреда

•Този уред е предназначен за битова употреба. Уредът не е предназначен за комерсиална употреба и не бива да се ползва за други цели освен предназначението му.

•Уредът може да се ползва за пране и изплакване само на пране, обозначено по съответния начин.

•Производителят не носи отговорност в случай на неправилна употреба или транспортиране.

1.3 Безопасност на децата

•Опаковъчните материали са опасни за децата. Дръжте опаковъчните материали на безопасно място, далеч от достъпа на деца.

•Електическите уреди са опасни за децата. Дръжте децата далеч от уреда когато той работи. Не им позволявайте да си играят с уреда. Използвайте защитата от деца за да предпазите децата от игра с уреда.

•Не забраяйте да затворите вратата на уреда когато напускате помещението, в което е разположен.

•Съхранявайте всички препарати и добавки на безпасно мяст, далеч от достъпа на деца, като покриете контейнера или залепите пакета на препарата.

1.4 Информация за опаковъчните материали

•Опаковъчните материали на продукта са произведени от рециклируеми материали в съответствие с наредбите за опазване на националната околна среда. Не изхвърляйте опаковъчните материали заедно с останалите битови отпадъци. Занесете ги в специалните пунктове за събиране на опаковъчни материали, определени от местните власти.

1.5 Изхвърляне на остарелия уред

•Продуктът е произведен от висококачествени части и материали, които могат да бъдат използвани повторно и са подходящи за рециклиране. Затова не го изхвърляйте заедно

снормалните битови отпадъци в края на сервизния му живот. Занесете го в събирателен пункт за рециклиране на електрическо и електронно оборудване. За да научите къде се намира най-близкият такъв пункт, се свържете

сместните власти. Помогнете в опазването

на околната среда и природните ресурси като рециклирате използваните продукти. С цел безопасността на децата, срежете захранващия кабел и счупете заключващия механизъм на вратата така, че да бъдат нефункционални преди изхвърлянето на продукта.

19 / 71 BG	Перална машина / Ръководство за употреба

1.6 Спазването на Директивата за WEEE

Този продукт носи символа за разделно

събиране на отпадъчно електрическо и

електронно оборудване (WEEE).

Това означава, че при рециклиране или

разглобяване продуктът трябва да се

третира съобразно Директива 2002/96/

EC с цел минимални последствия

за околната среда. За повече информация се

свържете с местните или регионалните власти.

Електронните продукти, които не са включени

в разделното събиране на отпадъци, са

потенциално опасни за околната среда и здравето

поради наличието на опасни вещества.

2 Монтаж

За монтажа на уреда се обърнете към найблизкия оторизиран сервиз. За да подготвите уреда за употреба, прегледайте информацията в това ръководство за употреба и проверете дали електрозахранването, водоподаването и канализацията са наред преди да повикате представител на оторизирания сервиз. Ако не са, се обадете на квалифициран техник и водопроводчик за да ги оправи.

Подготовката на мястото и електрическата, C водната и канализационната инсталация са

задължение на клиента.

BПРЕДУПРЕЖДЕНИЕ: Монтажът и свързването на електрозахранването на уреда трябва да бъдат извършени от представител на оторизирания сервиз. Производителят не носи отговорност за щети, причинени от процедури, извършени от неквалифицирани лица.

AПРЕДУПРЕЖДЕНИЕ:Преди монтажа огледайте уреда за видими дефекти. Ако има такива, не го монтирайте. Повредените уреди носят риск за безопасността ви.

C Проверете дали входящия и изходящия маркуч, както и захранващия кабел не са прегънати, затиснати или премазани при наместването на продукта на мястото му след монтажа или почистването.

2.1 Подходящо място за инсталиране

•Поставете машината върху твърд под. Не поставяйте машината върху черга или подобна повърхност.

•Общото тегло на пералната машина и сушилнята -заредени на пълен капацитетпоставени една върху друга достига до около 180 килограма. Поставете уреда върху здрав, равен под, способен да издържи на това натоварване!

•Не поставяйте уреда върху захранващия кабел.

•Не монтирайте уреда на място, където температурата може да падне под 0ºC.

•Поставете уреда на поне 1 см разстояние от ръба на други мебели.

2.2 Отстраняване на подсилващите

опаковъчни материали

Наклонете машината назад за да отстраните подсилващите опаковъчни материали. Отстранете подсилващите опаковъчни материали като издърпате опаковъчната лента.

2.3 Сваляне на болтовете за транспортиране

AПРЕДУПРЕЖДЕНИЕ:Не сваляйте болтовете за транспортиране преди да сте свалили подсилващите опаковъчни материали.

AПРЕДУПРЕЖДЕНИЕ:Отстранете обезопасяващите болтове за транспортиране преди да използвате пералнята! В противен случай ще повредите уреда.

1.Разхлабете винтовете с подходящ гаечен ключ докато започнат да се въртят свободно (C).

2.Отстранете винтовете за обезопасено пренасяне като ги развиете внимателно.

3.Наместете пластмасовите капачки, доставени в пакета с ръководството за употреба, в дупките от винтовете на задния панел. (P)

Съхранявайте болтовете за обезопасено C транспортиране, за да може да ги ползвате

отново ако се налага пренасяне на пералнята в бъдеще.

C Никога не пренасяйте пералнята без да сте завили правилно болтовете по местата им!

2.4 Свързване на водопровода

Водното налягане, необходимо за работата на C уреда, трябва да е между 1 и 10 бара (0.1 – 1

MPa). За да работи пералнята Ви нормално, са необходими 10 – 80 литра вода изтичащи от крана за една минута. Ако водното налягане е твърде високо, монтирайте понижаваща налягането клапа.

Ако ще ползвате уреда само в един вход за C вода (студена вода) вместо два, трябва да

монтирате капачката на клапата за топлата вода преди да пуснете уреда. (Важи за уреди, оборудвани с капачка.)

AПРЕДУПРЕЖДЕНИЕ:Моделите с единично водно захранване не се свързват с кран с топла вода. В този случай прането ще се повреди или уредът ще премине в режим на безопасност и няма да работи.

AПРЕДУПРЕЖДЕНИЕ:Не използвайте стари или употребявани маркучи с новия уред. Те може да направят петна по дрехите.

20 / 71 BG	Перална машина / Ръководство за употреба

1.Свържете специалните маркучи, доставени заедно с уреда, към входящите отвори за

водно захранване, разположени върху уреда. Червениятмаркуч (вляво) (макс. 90 ºC) е за

топлата вода, синият маркуч (вдясно) (макс. 25 ºC) е за студената вода.

AПРЕДУПРЕЖДЕНИЕ:Уверете се, че отводите за топла и студена вода са свързани правилно при монтажа. В противен случай в края на перилния цикъл прането може да е горещо и повредено.

2.Завийте всички гайки на маркуча с ръка. Никога не използвайте уред за затягането им.

3.Отворете крановете докрай след като свържете маркучите и проверете за изтичане в точките на свързване. Ако има изтичане на вода, затворете крана и свалете гайката. Проверете уплътнението и затегнете добре уплътнението. Когато машината не е в употреба, дръжте крановете затворени за да избегнете протичане на вода.

2.5 Свързване към отводнителната система

•Накрайникът на изходящия маркуч трябва да е свързан директно с канала за мръсна вода или мивката.

AПРЕДУПРЕЖДЕНИЕ:Може да наводните дома си ако маркучът се изтръгне от гнездото си по време на източване на водата. Освен това съществува риск от изгаряне поради високата теммпература на водата! За да избегнете подобни рискове и да осигурите безопасно наточване и източване на водата в машината, затегнете накрайникът на маркуча добре, така че да не може да се изтръгне.

•Маgкучът тgябва да се инсталиgа на най-малко 40 см и най-много 100 см височина.

•В случай, че маркучът е повдигнат след като е поставен на нивото на земята (по-малко от 40см над земята), източването на водата се затруднява и прането може да остане твърде

мокро. Затова спазвайте височините описани на фигурата.

•За да се избегне вливането на мръсна вода обратно в машината и да се осигури лесното й източване, не пъхайте маркуча в мръсната вода и не го вкарвайте в канала по-дълбоко от 15 см. Ако е твърде дълъг, го срежете.

•Краят на маркуча не бива да е извит, внимавайте да не е настъпен или прегънат по пътя между канала и машината.

•Ако маркучът е твърде къс, използвайте оригинално удължение. Дължината на маркуча не бива да надвишава 3.2 м.За да избегнете протичане на вода, свързването на удължението и дренажния маркуч на уреда

трябва да бъде направено с подходяща скоба за да не може да се откъсе и протече.

2.6 Регулиране на крачетата

AПРЕДУПРЕЖДЕНИЕ:За да работи уредът безшумно, без да вибрира, трябва да стои в равно и балансирано положение на крачетата. Балансирайте машината с тяхна помощ. В противен случай уредът може да се размести и да започне да вибрира или да нанесе щети.

1.Разхлабете с ръка гайките на крачетата.

2.Регулирайте крачетата така, че уредът да е нивелиран и балансиран.

3.Затегнете всички гайки на отново с ръка.

AПРЕДУПРЕЖДЕНИЕ:Не използвайте никакви уреди за разхлабване на контрагайките. В противен случай ще ги повредите.

2.7 Свързване на електричеството

Свържете уреда към заземен контакт, защитен с 16-амперов бушон. Фирмата ни не носи

21 / 71 BG	Перална машина / Ръководство за употреба

отговорност за щети по причина на ползване на уреда без заземяване направено съгласно местните наредби.

•Свързването трябва да е направено в съответствие с държавните стандарти.

•След монтажа захранващият кабел трябва да е леснодостъпен.

•Ако стойността на птока на бушона или прекъсвача у дома ви е под 16 ампера, накарайте квалифициран електротехник да монтира 16-амперов бушон.

•Волтажът, обозначен в "Техническите спецификации" трябва да отговаря на вашето захранване.

•Не свързвайте уреда чрез удължител или разклонител.

BПРЕДУПРЕЖДЕНИЕ:Повреденият захранващ кабел трябва да се подмени от представител на оторизирания сервиз.

Транспортиране на уреда

1.Изключете уреда от контакта преди транспортиране.

2.Свалете маркучите за източване и за входяща вода.

3.Източете всичката вода, останала в уреда. Вижте 5.5.

4.Монтирайте обезопасителните болтове в обратен ред на свалянето им; вижте 2.3.

C Никога не пренасяйте пералнята без да сте завили правилно болтовете по местата им!

AПРЕДУПРЕЖДЕНИЕ:Опаковъчните материали са опасни за децата. Дръжте опаковъчните материали на безопасно място, далеч от достъпа на деца.

3 Подготовка

3.1 Сортиране на прането

•Сортирайте прането според вида на тъканите, цвета, степента на замърсяване и допустимата температура на пране.

•Винаги спазвайте указанията върху етикета на дрехите.

3.2 Подготовка на дрехите за пране

•Металните части в прането, като банели на сутиени или катарами на колани могат да повредят пералнята Ви. Свалете металните части или перете дрехите в торбичка за пране или калъфка за възглавница.

•Изпразнете джобовете от монети, химикалки, кламери и други подобни, изкарайте джобовете навън и изчеткайте. Тези предмети могат да повредят машината и да предизвикат шум при прането.

•Поставяйте малки на размер дрешки като бебешки чорапки или найлонови чорапи в торбичка за пране или калъфка за възглавница.

•Поставете пердетата в машината без да ги притискате. Свалете окачалките на пердетата.

•Закопчайте циповете, зашийте разхлабени копчета и скъсани и разпорени места.

•Перете дрехи, означени с етикети “за машинно пране” или “за ръчно пране”, само със съответната за тях програма.

•Не перете цветно и бяло пране заедно. Нови, тъмни дрехи могат да пуснат много боя. Перете ги отделно.

•Упоритите петна трябва да се почистят добре преди изпирането. Ако не сте сигурни, проверете със сух препарат за петна.

•Използвайте бои, оцветители и избелващи вещества, подходящи за машинно пране. Винаги спазвайте инструкциите върху опаковката им.

•Перете панталоните и деликатното пране обърнати от опаката страна.

•Сложете дрехите от ангорска вълна във фризера за няколко часа преди пране. Това ще намали завалването на дрехите.

•Пране, силно напрашено с материали от рода на брашно, вар, мляко на прах и др., трябва добре да се изтупа преди поставяне в машината. В противен случай, тези прахообразни вещества се натрупват по вътрешните части на машината и може да я повредят.

3.3 Какво да направите за

да спестите енергия

Слеващата информация ще ви помогне да използвате уреда по екологичен и енергийноефективен начин.

•Пускайте уреда на максималния капацитет, позволен от програмата, която сте избрали, но не го претоварвайте; виж "Таблица с програми и консумация"

•Винаги спазвайте инструкциите на опаковката на перилния препарат.

•Перете слабо замърсеното пране на ниска температура.

•Използвайте бързи програми за малки количества леко замърсено пране.

•Не използвайте предпране и висока температура за пране, което не е силно замърсено и по него няма петна.

•Ако планирате да сушите прането си в сушилнята, при изпирането изберете най-високата препоръчана скорост на центрофугиране.

•Не използвайте повече препарат от препоръчаното върху пакета му.

3.4 Първоначална употреба

Преди да започнете употребата на продукта, се уверете, че всички подготвителни дейности са направени в съответствие с указанията в раздели "Важни указания за безопасност" и "Монтаж".

За да подготвите уреда за пускане на пране, го пуснете в програма Почистване на барабана първия път. Ако уредът ви е оборудван с

програма за почистване на барабана, извършете процедурата при първоначално ползване съгласно методите, описани в раздел "5.2 Почистване на вратата и барабана" на настоящето ръководство за употреба.

22 / 71 BG	Перална машина / Ръководство за употреба