Apple Studio Display User Manual



Studio Display

User’s Manual

Apple Computer, Inc.

Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. Your rights to the software are governed by the accompanying software license agreement.

The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws.

Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors.

Apple Computer, Inc. 1 Inﬁnite Loop Cupertino, CA 95014-2084 408-996-1010 http://www.apple.com

Apple, the Apple logo, ColorSync, Mac, Macintosh, PowerBook, PowerBook Duo, and Power Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Adobe, Adobe Illustrator, Adobe Photoshop, and PostScript are trademarks of Adobe Systems Incorporated or its subsidiaries and may be registered in certain jurisdictions.

The Energy Star logo is a service mark of the U.S. Environmental Protection Agency. Helvetica is a registered trademark of Linotype-Hell AG and/or its subsidiaries. NuBus is a trademark of Texas Instruments. PANTONE

and other Pantone, Inc. trademarks are the property of Pantone, Inc. Portions © Pantone, Inc. 1995. PowerPC is a trademark of International Business Machines Corporation, used under license therefrom. VESA Display Data Channel (DDC) is a trademark of the Video Electronics Standards Association. Simultaneously published in the United States and Canada. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a

recommendation. Apple assumes no responsibility with regard to the performance or use of these products.

Communications Regulation Information 6

1 Setting Up 7

Important Safety Instructions 7 What About Electromagnetic Emissions? 8 Using the Display 9 Do You Need to Install a Graphics Card? 10 Getting Ready to Set Up 12

Choosing a Good Location for Your Display 12

Positioning the Display 12 Using More Than One Display 14 Your Apple Studio Display at a Glance 16 Before You Set Up 17 Connecting the Display to Your Computer 17

Plugging In the Display 18

Connecting the Display Cable to a Mac OS–Based Computer 19

Connecting the Display Cable to a Windows-Based Computer 20

Connecting a Mac OS–Based Computer Keyboard and Mouse to the Desktop Stand 20 Turning the Display On 21 Turning the Display Off 22 Storing the Keyboard 22 Finding Answers 23 What’s Next 23

2 Installing and Using the Apple Displays Software 25

What’s Included in the Apple Displays Software? 25

Installing the Apple Displays Software on Mac OS–Based Computers 25 Installing Setup Information on Windows-Based Computers 27 Learning About the Apple Displays Software With Mac OS Help 28 Using the Monitors & Sound Control Panel 29 Using the Control Strip 31 About DigitalColor Meter 32 Specifying Colors Using the PANTONE Color Picker 32 Using ColorSync 32 Conserving Energy 32

What Happens After You Turn On the Energy-Saving Feature? 33 Setting Up Energy Saver 33 Using Energy Saver With a Screen Saver 34

Information About Copying Software 34

3 Using Manual Controls and the On-Screen Display 35

Using Manual Controls on Your Display 35 Accessing and Adjusting Controls in the On-Screen Display 37

Using the On-Screen Display in Computer Mode 38 Using the On-Screen Display in Video Mode 40

4 Attaching and Removing the Desktop Stand and Flip-Out Stand 43

Removing the Desktop Stand 43 Attaching the Flip-Out Stand 45 Removing the Flip-Out Stand 46 Attaching the Desktop Stand 47

5 Using Your Display for Video and Image Playback 49

About Video Formats 49 Connecting Video Equipment to Your Display 49

Connecting External Speakers 50 Connecting Video Equipment 51 Connecting to a Television Signal 52

Viewing Images and Making Adjustments to the Picture and Sound 52

6 Tips and Troubleshooting 55

Care and Cleaning 55

Contents

Cleaning the Case 55

Cleaning the Screen 55 Protecting Your Display From Theft 56 Using Mac OS Help 56 Troubleshooting 57

Monitor Power or Screen Appearance 57

Sound 59

Control Strip 60

Monitors & Sound Control Panel for Mac OS–Based Computers 60

Appendix Technical Information 63

General Speciﬁcations 63

Flat Panel Display 63

Desktop Stand 63

Flip-Out Stand 63

Power-Saving and Environmental Features 63

Weight 64

Dimensions of Display (with Desktop Stand) 64

Dimensions of Display (with Flip-Out Stand) 64

Temperature 64

Humidity (noncondensing) 65

Altitude 65

Active Video Image Area 65

Power Adapter Input Electrical Requirements 66

Interfaces 66

Display Cable Speciﬁcations 66

VGA Adapter Speciﬁcations 67

Contents

Communications Regulation Information

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the speciﬁcations in Part 15 of FCC rules. See instructions if interference to radio or television reception is suspected.

Radio and Television Interference

The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly—that is, in strict accordance with Apple’s instructions—it may cause interference with radio and television reception.

This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the speciﬁcations in Part 15 of FCC rules. These speciﬁcations are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

You can determine whether your computer system is causing interference by turning it off. If the interference stops, it was probably caused by the computer or one of the peripheral devices.

If your computer system does cause interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the computer to one side or the other of the television or radio.

Move the computer farther away from the television or radio.

Plug the computer into an outlet that is on a different circuit from the television or radio. (That is, make certain the computer and the television or radio are on circuits controlled by different circuit breakers or fuses.)

If necessary, consult an Apple-authorized service provider or Apple. See the service and support information that came with your Apple product. Or, consult an experienced radio/television technician for additional suggestions.

Important

Changes or modiﬁcations to this product not authorized by Apple Computer, Inc., could void the

FCC Certiﬁcation and negate your authority to operate the product. This product was tested for FCC compliance under conditions that included the use of Apple peripheral devices

and Apple shielded cables and connectors between system components. It is important that you use Apple peripheral devices and shielded cables and connectors between system components to reduce the possibility of causing interference to radios, television sets, and other electronic devices. You can obtain Apple peripheral devices and the proper shielded cables and connectors through an Apple-authorized dealer. For non-Apple peripheral devices, contact the manufacturer or dealer for assistance.

Industry Canada Statement

This Class B device meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du

Canada.

VCCI Class 2 Statement

Communications Regulation Information

CHAPTER

Setting Up

Read this chapter for important safety information and to set up and connect the display to your computer.

Important Safety Instructions

For your own safety and that of your equipment, always take the following precautions.

Warning

computer equipment may look similar, but they may damage your display. Disconnect the power plug (by pulling the plug, not the cord) if any of the following

conditions exists:

the power cord or plug becomes frayed or otherwise damaged

you spill something into the case

your display is exposed to rain or any other excess moisture

your display has been dropped or the case has been otherwise damaged

you suspect that your display needs service or repair

you want to clean the case or screen (use only the recommended procedures described

in “Care and Cleaning” on page 55)

Important

the Apple Desktop Bus (ADB) cable. Make sure at least one end of the power cord is within easy reach so that you can unplug the display when you need to.

Be sure that you always follow these instructions:

Keep your display away from sources of liquids and moisture.

Keep the display’s vents free from obstruction.

Don’t set anything on top of the display.

Read all the setup instructions carefully before you plug your display into a power source.

Use only the power adapter that came with your display. Adapters for other

The only way to disconnect power completely is to unplug the power cord and

Keep these instructions handy for reference by you and others.

Follow all instructions and warnings dealing with your system.

Warning

Never remove the case from the display! You could come in contact with

hazardous voltage. Electrical equipment may be hazardous if misused. Operation of this product, or similar

products, must always be supervised by an adult. Do not allow children access to the interior of any electrical product and do not permit them to handle any cables.

What About Electromagnetic Emissions?

There has been recent public discussion of the possible health effects of prolonged exposure to extremely low frequency (ELF) and very low frequency (VLF) electromagnetic ﬁelds. Such ﬁelds are associated with electromagnetic sources such as television sets, electrical wiring, and some household appliances—as well as computer monitors.

Apple has reviewed scientiﬁc reports and sought the counsel of government regulatory agencies and respected health organizations. Based on the prevailing evidence and opinions, Apple believes that the electric and magnetic ﬁelds produced by computer monitors do not pose a health risk.

In response to those customers who wish to reduce their exposure to electromagnetic ﬁelds, Apple has lowered the emission levels of our products. We are also actively encouraging further scientiﬁc research so we can continue to promote the health and safety of our customers and employees.

Chapter 1

Using the Display

You can use your display in several ways.

You can connect your display to a Power Macintosh computer or a Windows-based

computer.

You can use the ﬂip-out stand if you want the display to be more portable, such as when

you are giving presentations.

Note:

You won’t be able to adjust the tilt or height of the display. To use any of the

controls on the underside of the display, you’ll need to lift the display up slightly.

Setting Up

You can connect a videocassette recorder (VCR), camcorder, or digital camera to the display and view videos or images.

Do You Need to Install a Graphics Card?

To use your display, you need compatible video circuitry built into your computer, or a compatible graphics or video card installed in your computer. The display works with the built-in video circuitry of Power Macintosh computers and PowerPC™-based PowerBook computers that have an external monitor port. If you have another Mac OS–based computer or a Windows-based computer, check to see that its video circuitry operates at the resolutions speciﬁed here.

If you are not sure whether your computer or graphics card has the appropriate built-in video capability, check with an Apple-authorized dealer if you have a Mac OS–based computer, the computer’s manufacturer, or a service provider.

Note:

If you’re using more than one display, you may need a graphics card for each

additional display you are using. The display supports 14 predeﬁned resolutions. Your computer or graphics card must

support at least one of these resolutions for the display to work with your computer.

Note:

Apple recommends that your graphics card support the optimum resolutions.

Chapter 1

The actual resolutions and vertical refresh rates that are available to you depend on the video circuitry of your computer or graphics card. See the documentation that came with your computer or graphics card for more information.

Resolution

640 x 480 640 x 480 640 x 480 640 x 480

Vertical refresh rate (Hertz)

60 67 72

75 720 x 400 70 800 x 600

800 x 600 800 x 600 800 x 600

75 832 x 624 75 1024 x 768

1024 x 768 1024 x 768

Note:

1 1 1

These are the optimal modes for the display—the resolutions that don’t require zoom and provide the sharpest image. If your computer does not support these, you may want to get a graphics card

The Apple 8•24, Apple 8•24GC, Apple 24AC, some NuBus™ graphics cards, and some

74.9/75

third-party PCI cards are not fully compatible with your display. If a card is not fully compatible, the software cannot be used to adjust the screen image or change resolutions, but the controls on the underside of the display can be used to adjust some settings.

If you are using a graphics card, install it before you connect the display to your computer. To install a graphics card in one of the expansion slots inside your computer, see the documentation that came with the computer or graphics card.

Setting Up

Getting Ready to Set Up

As you begin to set up your display system, make sure you have easy access to the following items.

VGA adapter (only if you are connecting the display to a Windows-based computer)

Apple Displays Software

CD-ROM disc Power adapter

Power cord

Choosing a Good Location for Your Display

Consider these factors when determining where to place your display:

Make sure the power adapter cable, power cord, and display cables will easily reach from the back of the display to your computer and an electrical outlet or power strip.

All cables should be unobstructed when you adjust the display. If you don’t allow enough clearance, the connectors might be damaged when the cables hit an obstruction.

Positioning the Display

If you’re using the display with the desktop stand, you can adjust it for your greatest comfort.

Note:

If you’re using the ﬂip-out stand, move the display on the desk or table until you can

see the screen clearly; there are no height adjustments.

Important

Before you adjust the display, make sure there is enough slack in the cables. If

you don’t allow enough clearance, the cables or connectors might be damaged.

Place the display so the screen faces you.

Chapter 1

Adjust the height of the display by pulling up or pushing down on the display.

Adjust the viewing angle of the monitor by tilting it up or down and turning it left or right on

the desktop stand.

Setting Up

Position the display so that when you use it, no bright light is behind the display or reﬂected on the screen. Your eyes should be about level with the top edge of the screen and between 18 and 28 inches (45 and 70 cm) away. Take occasional breaks when using your computer to focus your eyes on a distant object.

Use the following illustration to help you in positioning your monitor.

45–70 cm (18–28 in.)

Shoulders relaxed

Forearms and hands

in a straight line

Forearms level

or tilted up slightly

Lower back supported

Thighs horizontal

Top of the screen at or slightly below eye level (You may need to adjust the height of your display, if you use the desktop stand.)

Tilt screen to avoid reflected glare

Clearance under work surface

Feet flat on the floor

Using More Than One Display

If your computer has expansion slots, you can use your display with one or more additional displays connected to your computer. You may need a graphics card for each additional display you are using. See the manual that came with your computer for more information.

Note:

If you’re connecting the display to a PowerBook computer, you must use the adapter

that came with the computer, not the display. If your Mac OS–based computer has only one ADB port, you can still connect two displays.

You may need a special cable to split the ADB connector cable into two parts.

Chapter 1

Note:

Some displays don’t require the use of an ADB connection. For these displays, you

only need to connect the display cable to a monitor port on your computer.

(includes monitor

connector and

ADB connector)

Important

Display cable

Make sure you use an Apple shielded connector cable. Most third-party ADB

Display cable (includes monitor connector and ADB connector)

Shielded connector cable (Apple part number M5556LL/A)

splitter cables are not shielded and will not work properly with your display. You may experience more radio interference with an unshielded connector cable.

Setting Up

Your Apple Studio Display at a Glance

Display controls

(underneath)

Keyboard storage pads

Power

indicator light

® Power button

(underneath)

Carrying handle

AV port cover

V ADB cable

Desktop stand

V ADB ports

Power adapter cable

V ADB connector

™ Display cable

Chapter 1

Before You Set Up

Consider these factors when you connect cables:

For easier management of the cables when you’re using the desktop stand, use the cable guide. The ADB cable, display cable, and power adapter cable should go through the cable guide.

Cable guide

The ADB cable has a plastic cable capture in the middle of the cable. This capture allows slack in the ADB cable so the cable won’t get damaged when you adjust the display.

Connecting the Display to Your Computer

Follow these steps to connect your display to your computer.

Important

Before you connect any cords or cables, make sure that your computer is

turned off but plugged in to provide proper grounding.

Plug in the display

Connect the display cable to your computer

Connect your Mac OS–based keyboard and mouse to the desktop stand

Turn the display on

Setting Up

Plugging In the Display

Warning

Use only the power adapter that came with your display. Adapters for other

computer equipment may look similar, but they will damage your display.

Plug the power adapter cable from the display into the power adapter.

Power

Power cord

Power adapter

Plug one end of the power cord into the power adapter and the other end into a three-hole

adapter cable

grounded outlet or power strip. If you have a different type of power cord, plug it into the power socket on the back of your

computer.

Warning

This equipment is intended to be electrically grounded. The power adapter

that came with your display is equipped with a three-wire grounding plug—a plug that has a third (grounding) pin. This plug will ﬁt only a grounded AC outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact a licensed electrician to replace the outlet with a properly grounded outlet. Do not defeat the purpose of the grounding plug!

Chapter 1

Connecting the Display Cable to a Mac OS–Based Computer

The display cable is a split cable with two connectors, one for the display and one for the Apple Desktop Bus (ADB).

V ADB connector ™ Display connector

Plug the display connector on the display cable into the monitor port (marked with ™) on the back of the computer.

Monitor port icon

Connector on display cable

If you’re connecting the display to a PowerBook computer, connect the adapter that came with the computer to the display connector on the display cable. You must use the adapter that came with your computer, not the one that came with this display.

If you installed a graphics card in your computer, connect the display connector to the graphics card’s port.

If your computer has more than one monitor port, see the documentation that came with your computer for information on choosing the correct port.

Tighten the thumbscrews on the connector. You can prevent bad connections and accidental damage by tightening the thumbscrews. Do

not overtighten the thumbscrews; you might strip the threads.

3 If necessary, unplug the keyboard or mouse cable from the ADB connector on the back of

your computer.

4 Plug the ADB connector on the display cable into the ADB port (marked with V) on the back

of your computer. Align the symbol on the ADB connector with the same symbol on the port. If you force a

connector the wrong way, you will damage it. Make sure the ADB connector is attached ﬁrmly.

Important The ADB connector is not optional; it’s needed for your Mac OS–based

computer to work correctly with your display. If the ADB connector on the display cable is not connected properly, the maximum number of resolutions and software controls will not be available.

Setting Up

Connecting the Display Cable to a Windows-Based Computer

Although the display cable is a split cable with two connectors, you will use only the display connector with your computer.

1 Connect the VGA adapter to the display connector on the display cable.

Monitor port on Windows-based computer

VGA adapter

Connector on display cable

2 Tighten the thumbscrews on the connector.

You can prevent bad connections and accidental damage by tightening the thumbscrews. Do not overtighten the thumbscrews; you might strip the threads.

3 Connect the VGA adapter end of the display cable to the monitor port on the back of your

computer. If you installed a graphics card in your computer, connect the display cable (with the VGA

adapter attached to it) to the graphics card’s port. For more information about installing graphics cards, see the documentation that came with your computer or graphics card.

4 Tighten the thumbscrews on the connector. 5 Leave the ADB connector on the display cable unplugged.

The ADB connector is for Mac OS–based computers only.

Connecting a Mac OS–Based Computer Keyboard and Mouse to the Desktop Stand

There is one ADB port on each side of the desktop stand for your keyboard and mouse (or any other ADB input device).

Important Always be sure your computer is shut down before you plug in or disconnect

ADB cables to prevent damage to the display.

1 Make sure the ADB connector on the display cable is plugged into the ADB port (marked

with V) on the back of your computer. For more information, see “Connecting the Display Cable to a Mac OS–Based Computer” on

page 19.

20 Chapter 1

2 Decide how you want to connect the keyboard and mouse.

ADB port on the desktop stand

For example, you can connect your mouse cable to your keyboard and then connect the keyboard to one of the ADB ports (marked with V) on either side of the desktop stand. Or, if you prefer, you can plug both your keyboard and mouse into the ADB ports (marked with V) on the desktop stand.

Note: If you have a USB keyboard and mouse, see the documentation that came with your computer for instructions on connecting your keyboard and mouse to your computer.

3 Connect your keyboard and mouse cables to ADB ports (marked with V) on the desktop

stand, according to your preference.

When connecting ADB cables, make sure you align the symbol on the connector with the same symbol on the port. If you force a connector the wrong way, you will damage it. Make sure the ADB connector is attached ﬁrmly.

Turning the Display On

To turn on the display, follow these steps:

1 Make sure the display’s power cord is plugged into a grounded electrical outlet or power

strip. If you plugged the display into the back of your computer, make sure the computer’s power

cord is plugged into a grounded electrical outlet or power strip.

2 Start up your computer.

After a few seconds, the power indicator light on the display turns amber and then green. If you don’t see an amber light, press the power (®) button on the right underside of the display. If the power indicator light doesn’t turn green, shut down and unplug your computer and make sure you’ve connected the display cable, power adapter cable, and power cord properly.

Setting Up 21

+ 47 hidden pages