AEG 750 User Manual

Size:
3.04 Mb
Download

OPERATING INSTRUCTIONS UPS

PROTECT B.

PROTECT B. 750 PROTECT B. 1000 PROTECT B. 1500

PROTECT B. 2000

1

PROTECT B. 3000

Thank you for purchasing a PROTECT B. UPS from AEG Power Solutions.

The following security advices are an important component of the manual and will prevent any operation errors and protect you against possible dangers. Read the manual thoroughly before you first use the appliance.

2

1Notes on these Operating Instructions

Duty to Provide Information

These operating instructions will help you to install and operate the UninterruptiblePowerSupply (UPS), PROTECT B. 750, PROTECT B. 1000, PROTECT B. 1500, PROTECT B. 2000 or PROTECT B. 3000 as well as the associated external battery units PROTECT B. 1500 BP, PROTECT B. 2000 BP or PROTECT B. 3000 BP – all referred to as PROTECT B. in this document – safely and properly, and for its intended purpose. These operating instructions contain important information necessary to avoid dangers during operation.

Please read these instructions carefully prior to commissioning!

These operating instructions are a composite part of PROTECT B.

The operator of this operating instructions up PROTECT B. or work on the unit.

unit is obliged to communicate these to all personnel transporting or starting performing maintenance or any other

Validity

These operating instructions comply with the current technical specifications of PROTECT B. at the time of publication. The contents do not constitute a subject matter of the contract, but serve for information purposes only.

Warranty and Liability

Our goods and services are subject to the general conditions of supply for products of the electrical industry, and our general sales conditions. We reserve the right to alter any specifications given in these operating instructions, especially with regard to technical data and operation.

3

Claims in connection with supplied goods must be submitted within eight days of receipt, along with the packing slip. Subsequent claims cannot be considered.

The warranty does not apply for damage caused by noncompliance with these instructions (such damage also includes damaging the warranty seal). AEG will accept no liability for consequential damage. AEG will rescind all obligations such as warranty agreements, service contracts, etc. entered into by AEG and its representatives without prior notification in the event of maintenance and repair work being carried out with anything other than original AEG spare parts or spare parts purchased by AEG.

Handling

PROTECT B. is designed and constructed so that all necessary steps for start-upand operation can be performed without any internal manipulation of the unit. Maintenance and repair work may only be performed by trained and qualified personnel.

Illustrations are provided to clarify and facilitate certain steps.

If danger to personnel and the unit cannot be ruled out in the case of certain work, it is highlighted accordingly by pictograms explained in Chapter 3.

Hotline

If you still have questions after having read these operating instructions, please contact your dealer or our "Hotline":

Tel.:

+49 (0)180 5 234 787

Fax:

+49 (0)180 5 234 789

Internet:

www.AEGpartnernet.com

Copyright

No part of these operating instructions may be transmitted, reproduced and/or copied by any electronic or mechanical means without the express prior written permission of AEG.

© Copyright AEG 2009 . All rights reserved.

4

Table of Contents

1 Notes on these Operating Instructions .............................

3

2

System Description ..........................................................

7

 

2.1

Overview ...................................................................

7

 

2.2

Functionality ..............................................................

8

3

Safety

.............................................................................

10

 

3.1

General .....................................Safety Instructions

10

 

3.2

Safety ........................Instructions for PROTECT B

10

 

3.3

Certification .............................................................

14

 

3.4

Technical ........................................................Data

15

4

Set-Up ....................................................andOperation

20

 

4.1

Unpacking .......................................and Inspection

20

 

4.2

Point ..................................................of installation

21

 

4.3

Connections, ............Operation / Display Elements

22

 

4.3.1 ........................................................

Front view:

22

 

4.3.2 ...............................................

Operating panel

23

 

4.3.3 .................................

Rear view (connections):

24

5

Commissioning...............................................................

26

 

5.1

Deployment .............................................................

26

 

5.1.1 .....................

Tower (Stand alone deployment)

26

 

5.1.2 .....................................

19” Rack Mount Setup

28

 

5.2

Additional .........................battery installation setup

32

 

5.3

Emergency .......................Power Off (EPO) set up

33

 

5.4

Electric .......................................................start-up

34

 

5.4.1 .......................................................

Connection

34

 

5.4.2 ....................................................

Configuration

35

 

5.5

Operation.................................................................

36

 

5.5.1 .............................................

Normal Operation

36

 

5.5.2 .....

Battery Operation / Autonomous Operation

36

 

5.5.3 ...................................................

Unit Overload

37

 

5.5.4 ......................

System Diagnosis / Battery Test

38

5

5.6 Interfaces and communication ................................

39

5.6.1

Data line protection RJ11 and RJ45

 

 

(modem / telephone / fax / network).................

39

5.6.2

Computer interfaces RS232 and USB .............

40

5.6.3Communication slot

 

 

 

(PROTECT B.1500 / B.2000 / B.3000):............

40

 

5.6.4

Shutdown and UPS management software .....

40

6

Signalling and failure solution.........................................

42

 

6.1

LED display .............................................................

42

 

6.2

Audible Alarm Trouble Shooting: ............................

44

 

6.3

General Fault Diagnosis and Fault Rectification .....

44

7

Maintenance...................................................................

46

 

7.1

Battery replacement ................................................

47

8

Storage, Dismantling and Disposal ................................

52

9

Glossary .........................................................................

53

 

9.1

Technical terms.......................................................

53

6

2 System Description

PROTECT B. is an UninterruptiblePowerSupplyi (UPS) for essential loads such as PCs, workstations, servers, network components,

telecommunication equipment and similar devices.

The PROTECT B. series is a compact, interactive, sinusoidaly operating USP, available with an output power rate of 750, 1000, 1500, 2000 and 3000 VA.

The design of the USP allows horizontal / lying operation (Rack/19" with 2U) and vertical / standing operation (Tower).

2.1Overview

The front of the UPS provides several LEDs and four push buttons for easy configuration, control and management. The panel also informs about the state of the power in the alternating current (AC) branch, indications on net failures and the charging state of the Output of the UPS. You will find two LED bars for output load and battery capacity, two state indicators (net available, battery active) and four alarm indicators (power failure, failure, battery discharged, overload). With the push button the acoustic alarm can be deactivated and the self test of the UPS will be started.

Power connectors, communication interfaces and connections for telephone and network are located on the rear of the PROTECT B. Important UPS parameters and data are constantly monitored and are transmitted via USB or serial RS232 to the “CompuWatch” Software on the management computer. The optional SNMP adapter allows remote monitoring via SNMP connector and multi server shutdown (starting with B.1500).

The main features of the PROTECT B. are:

VI (Line Interactive) protection technology with sinusoidal output voltage

AVR control system

(automatic voltage regulation with mains operation)

7

Micro processor control for high availability, suited for generator mode

Easy extension of battery capacity using external batteries (starting with B.1500)

Advanced battery management with integrated protection against extreme discharge and overcharge

Overload and short circuit proof

Maintenance free, sealed lead batteries, hot swappable (starting with B.1500)

User friendly display

for optimal readability / configuration

Intelligent monitoring system with USB and RS232 interface

Surge protection (RJ11 / RJ45)

for phone, fax, modem and network (10/100MBit/s)

Expansion slot for extension cards, i.e. SNMP (starting with B.1500)

“CompuWatch” software for shutdown, state report and measurement for all popular operating systems (among others Windows, Mac, Linux)

Compact design / variable deployment due to combination design as tower / rack (19” kit available optionally for all models)

2.2Functionality

The UPS is connected to a shockproof socket between the public utility's mains and the loads to be protected.

Under normal operating conditions, i.e. if PROTECT B. is supplied with mains voltage, the battery charger will ensure that the battery is always completely charged.

During this operating status, the loads connected to PROTECT B. are supplied with voltage via mains filters which provide effective protection against mains voltage peaks and high-frequencyfaults.

In case of sustained mains undervoltage or overvoltage within defined ranges, the automatic voltage regulator (AVR) further

8

stabilizes the load voltage. As a result, voltage fluctuations in the public utility's mains are reduced to a level which is acceptable for the loads. This is performed without recourse to the internal energy storage, something which in turn has a positive effect on battery availability.

UPS block diagram PROTECT B.

The static bypass switch is activated in the event of a mains failure. The inverter then takes over the voltage supply of the connected loads, in order to prevent the risk of data loss or damage to the loads. PROTECT B. supplies voltage until the battery is discharged, allowing you to shut down your IT system properly and switch it off. The standby time mainly depends on the connected loads. If the mains power supply is back to normal values, the UPS will switch back the loads to mains supply. The battery charger will then recharge the battery.

For safety reasons (as required by German standards, VDE), the mains input in the unit will be disconnected by a two-poleswitch in the event of a mains failure. Energy backfeed to the mains and voltage supply to the pins of the mains connector are thus reliably avoided.

Furthermore, additional protective measures ensure effective protection for the data/network interface.

9

3 Safety

3.1General Safety Instructions

Read these operating instructions carefully prior to commissioning of the PROTECT B. UPS and observe the safety instructions!

Only use the unit if it is in a technically perfect condition and always in accordance with its intended purpose, while being aware of safety and danger aspects, and in accordance with the operating instructions! Immediately eliminate any faults which could be detrimental to safety.

The following pictograms are used in these operating instructions to identify dangers and important information:

 

Danger!

 

Identifies risk of fatal injury to the operator.

 

Attention!

 

Identifies risk of injury and risk of damage to the

 

unit and parts of the unit.

i

Information!

Useful and important information for operating

the UPS.

3.2Safety Instructions for PROTECT B.

This chapter contains important instructions for the PROTECT B. UPS. These must be followed during assembly, operation and maintenance of the uninterruptible power supply and the batteries.

The UPS carries high voltage. Danger! The unit may only be opened by trained and qualified personnel. Repairs may only be carried out by qualified customer service staff!

10