Sharp NOTEVISION XR-1S Manual

0 (0)

MULTIMEDIA PROJECTOR

MODEL

XR-1X XR-1S

OPERATION MANUAL

Introduction Quick Start

Setup

Connections

(The picture shown above is of the XR-1S.)

Operation

Basic

Features

Useful

Appendix

IMPORTANT

For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 11.

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 5A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth Blue : Neutral

Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

or and of the same rating as above, which is also indicated on the pin

Model No.:

Serial No.:

• The wire which is coloured green-and-yellow must be connected to the terminal in the

plug which is marked by the letter E or by the safety earth symbol green-and-yellow.

or coloured green or

• The wire which is coloured blue must be connected to the terminal which is marked with

the letter N or coloured black.

• The wire which is coloured brown must be connected to the terminal which is marked with

the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese) and Korean. Carefully read through the operation instructions before operating the projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch (Traditionelles Chinesisch und einfaches Chinesisch) und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois, espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et chinois simplifié) et coréen. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska (traditionell kinesiska och förenklad kinesiska) och koreanska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español, italiano, holandés, portugués, chino (chino tradicional y chino simplificado) y coreano. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano, olandese, portoghese, cinese (cinese tradizionale e cinese semplificato) e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans, Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees) en Koreaans. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.

O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês, (Chinês Tradicional e Chinês Simplificado) e Coreano. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.

Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view

directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose

this product to rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

DO NOT REMOVE COVER.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications to

this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

U.S.A. ONLY

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification.

U.S.A. ONLY

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the ON/STANDBY button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

CAUTION ON LITHIUM BATTERY (for Remote Control unit)

If a battery is reversed (positive end where the negative end belongs and vice versa), it can overheat and rupture. This has happened when young children install batteries backwards. Warn children

battery in the remote control.

not

to take out batteries or install them.

Parents should install the lithium

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 55.

LAMP REPLACEMENT WARNING

BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT MODEL AN-XR1LP ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING. HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.

AVERTISSEMENT A OBSERVER LORS DU REMPLACEMENT DE LA LAMPE.

DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS. L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE. NE REMPLACER QUE PAR UNE LAMPE SHARP DE MODÈLE AN-XR1LP. RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX. ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN. LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE. A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.

This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 (XR1X) / 480,000 (XR-1S) pixels micromirrors. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

How to Read this Operation Manual

■ The specifications of the XR-1X are slightly different from those of the XR-1S, however, you can

connect and operate both models in the same manner. This operation manual uses the XR-1S for the purpose of explanation.

• In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly from actual display.

Using the Menu Screen

The menu can be operated to achieve two functions, adjustment and setting. (For setting the menu items, see pages 38 and 39.)

Operating with the projector

When “PRJ - ADJ” - “Guide LEDs” is set to “On”, the buttons used for menu adjustment on the projector light up.

Example: When W, Y and the MENU/HELP button light up on the projector, you can use those buttons for operation.

Adjustment buttons (W/Y/V/X)

MENU/HELP button

Introduction

ENTER button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press BMENU.

• The “Picture” menu screen for the selected input mode is displayed.

Press Q or O to display the other

menu screen.

• The selected menu item is highlighted.

Example: “Picture” screen menu for INPUT 1 (RGB) mode

Menu item

Picture

SCR - ADJ PRJ - ADJ Help Picture Mode Contrast 0

Bright Red Blue CLR Temp Bright Boost sRGB Reset

SEL./ADJ. ENTER END

Info

........Indicates safeguards for using the projector.

.........Indicates additional information for setting up and operating the

Note

projector.

For Future Reference

MENU/HELP button

MOUSE Adjustment button (P/R/O/Q)

ENTER button

RETURN button

Standard

0 0 0 K7500

Off Off

Buttons used in this operation

Button used in this step

On-screen display

PP. 60 and 61

IndexMaintenance Troubleshooting

P. 6 5P. 5 2

Contents

Preparing

Introduction

How to Read this Operation Manual .... 3

Contents ............................................... 4

IMPORTANT SAFEGUARDS ............... 6 How to Access the PDF Operation

Manuals ............................................ 10

Accessories ........................................ 11

Part Names and Functions ................. 12

Inserting the Lithium Battery ................ 14

Usable Range ...................................... 15

Quick Start

Quick Start .......................................... 16

Using

Basic Operation

Turning the Projector On/Off .............. 26

Turning the Projector on ....................... 26 Turning the Power off (Putting the

Projector into Standby Mode) ........... 26

Image Projection................................. 27

About the Setup Guide ........................ 27

Adjusting the Projected Image ............ 27

Switching the Input Mode .................... 29

Adjusting the Volume ........................... 29 Displaying the Black Screen and Turning

off the Sound Temporarily ................. 29

Resize Mode ......................................... 30

Useful Features

Adjusting/Operating with the

Remote Control ................................ 32

Auto Sync (Auto Sync Adjustment) ..... 32

Freezing a Moving Image .................... 32

Selecting the Picture Mode .................. 32

Using Mouse Function ......................... 33

Menu Items ......................................... 34

Using the Menu Screen ...................... 36

Menu Selections (Adjustments) ........... 36

Menu Selections (Settings) .................. 38

Setup

Setting up the Projector ...................... 18

Setting up the Projector ....................... 18

Standard Setup (Front Projection) ....... 18

Projecting a Reversed Image .............. 18 Screen Size and Projection Distance

(XR-1X) ............................................... 19

Screen Size and Projection Distance

(XR-1S) ............................................... 20

Connections

Connections ........................................ 21 Samples of Cables for Connection .... 22

Connecting to a Computer ................. 23

Connecting to Video Equipment......... 24

Connecting the Power Cord ............... 25

Picture Adjustment (“Picture” menu) .. 40

Selecting the Picture mode .................. 40

Adjusting the Image ............................. 40

Adjusting the Color Temperature ......... 41

Emphasizing the Contrast .................... 41

Progressive ........................................... 42

sRGB Setting ........................................ 42

Adjusting the Projected Image

(“SCR - ADJ” menu) ......................... 43

Setting the Resize Mode ...................... 43

Adjusting the Image Position ............... 43

Keystone Correction ............................ 44

Setting On-screen Display ................... 44

Selecting the Background Image ........ 45

Setting the Setup Guide ....................... 45 Reversing/Inverting Projected

Images ............................................... 46

Selecting the On-screen Display

Language ........................................... 46

Setting the Projector Function

(“PRJ - ADJ” menu).......................... 47

Eco/Quiet Mode ................................... 47

Auto Search Function ........................... 47

Auto Power Off Function ...................... 48

Setting the Guide LEDs ........................ 48

System Lock Function .......................... 49

Setting/Changing the keycode ............ 49

Setting the Confirmation Sound ........... 50

Checking the Lamp Life Status ........... 50

Troubleshooting with “Help” menu ..... 51

Displaying “Help” menu screen .......... 51

Reference

Introduction

Appendix

Maintenance ....................................... 52

Maintenance Indicators ...................... 53

Regarding the Lamp ........................... 55

Lamp ..................................................... 55

Caution Concerning the Lamp ............ 55

Replacing the Lamp ............................. 55 Removing and Installing

the Lamp Unit .................................... 56

Resetting the Lamp Timer .................... 57

Connecting Pin Assignments ............. 58

Computer Compatibility Chart ............ 59

Troubleshooting .................................. 60

For SHARP Assistance....................... 62

Specifications ..................................... 63

Dimensions ......................................... 64

Index ................................................... 65

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product

and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with

a grounding terminal. This plug will only fit into a grounding type power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.

Introduction

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e. If the product has been dropped or damaged

in any way.

f. When the product exhibits a distinct change

in performance, this indicates a need for service.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

• DLP\ (Digital Light Processing) and DMD\ (Digital Micromirror Device) are trademarks of Texas Instruments, Inc.

• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the United States.

• Adobe Reader is a trademark of Adobe Systems Incorporated.

• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

• All other company or product names are trademarks or registered trademarks of their respective companies.

Be sure to read the following safeguards when setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass par-

ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for a replacement. See “Replacing the Lamp” on page 55.

AN-XR1LP

Caution concerning the setup of the projector

■ For minimal servicing and to maintain high

image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

Do not set up the projector in places exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct

sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projector.

■ Place the projector on a level site within the

adjustment range of the adjustment foot.

Do not turn the projector upside down immediately after putting into standby mode.

■ This may cause burns due to rise in tempera-

ture of the lamp unit cover.

Warning about placing the projector in a high position

■ When placing the projector in a high position,

be sure to secure it carefully to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■ Take care with the lens so as not to hit or

damage the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long

hours will cause eye strain. Be sure to occasionally rest your eyes.

Avoid locations with extremes of temperature.

■ The operating temperature of the projector is

from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is

from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■ Allow at least 11 13/16 inches (30 cm) of space

between the exhaust vent and the nearest wall or obstruction.

■ Be sure that the intake vent and the exhaust

vent are not obstructed.

■ If the cooling fan becomes obstructed, a pro-

tection circuit will automatically put the projector into standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 53 and 54.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

■ When turning off the projector, the cooling fan

runs to decrease the internal temperature for a while. Unplug the power cord after the cooling fan stops. The period the cooling fan runs will vary, depending on the circumstances and the internal temperature.

Caution regarding transportation of the projector

■ When transporting the projector, be sure not

to subject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. Before moving the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

■ Do not carry the projector by holding the lens. ■ When transporting the projector, be sure to

place the projector in the supplied soft case. (See page 11.)

Other connected equipment

■ When connecting a computer or other audio-

visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.

■ Please read the operation manuals of the pro-

jector and the equipment to be connected for instructions on how to make the connections.

Using the projector in other countries

■ The power supply voltage and the shape of

the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, be sure to use an appropriate power cord for the country you are in.

Info

• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.

• Do not unplug the power cord during projection or cooling fan operation. This can cause damage due to rise in internal temperature, as the cooling fan also stops.

Introduction

Temperature monitor function

■

If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter standby mode. Refer to “Maintenance Indicators” on page 53 for details.

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector, even if you do not have this manual. To utilize these manuals, you need to install Adobe Reader on your computer (Windows or Macintosh).

Please download Adobe Reader from the Internet (http://www.adobe.com).

Accessing the PDF Manuals

For Windows:

1 Insert the CD-ROM in the CD-ROM

drive.

2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4 Double click the language (name of the

folder) that you want to view.

5 Double click the “XR1” pdf file to access

the projector manuals.

Note

• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe Reader first, then specify the desired file using the “File”, “Open” menu.

For Macintosh:

1 Insert the CD-ROM in the CD-ROM

drive.

2 Double click the “CD-ROM” icon. 3 Double click the language (name of the

folder) that you want to view.

4 Double click the “XR1” pdf file to access

the projector manuals.

Accessories

Supplied accessories

Introduction

Lithium battery

(CR2025)

UBATL0011TAZZ

Remote control

RRMCGA256WJSA

Soft case

GCASNA011WJZZ

Power cord*

(1) (2) (3) (4)

For U.S., Canada,

etc.

(6' (1.8 m))

QACCDA029WJPZ

* Use the power cord that corresponds to the wall outlet in your country.

For Europe, except

U.K.

(6' (1.8 m))

QACCVA006WJPZ

RGB/USB cable

(6' (1.8 m))

QCNWGA047WJPZ

• Projector manual CD-ROM UDSKAA045WJN1

• Operation manual (this manual)

For U.K., Hong Kong

and Singapore

(6' (1.8 m))

QACCBA015WJPZ

Cable tieK2

UBNDTA015WJZZ

• For the RGB/USB cable

• For the power cord

For Australia, New

Zealand and Oceania

(6' (1.8 m))

QACCLA024WJPZ

Optional accessories

■ 3 RCA to 15-pin D-sub cable (9n10o (3.0 m)) ■ Lamp unit

Note

• Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.

Carrying the Projector

Using the Soft Case

AN-C3CP AN-XR1LP

Tying the Cables

Tie the cable using the supplied cable ties.

Power cord RGB/USB cable

Info

• Be sure the projector has cooled down sufficiently before placing it in the case.

• This soft case is only for storing and carrying the projector.

• Shipping the projector in the soft case as a parcel may cause damage to the projector. If you send the projector in the carrying case as a parcel, be sure to place it in a sturdy case and with enough shock absorbing material to avoid any damage.

Note

• You cannot store the supplied cables within the soft case. When transporting the projector, prepare a bag for these cables.

Part Names and Functions

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

Projector

Top View

Lamp indicator

ON/STANDBY button

For turning the power on and putting the projector into standby mode.

ENTER button

For setting items selected or adjusted on the menu.

Adjustment buttons (W/Y/V/X)

For selecting menu items.

Front View

HEIGHT ADJUST button

26 54

Setup Guide indicators

Temperature warning

indicator Volume buttons (V/X)

For adjusting the speaker sound level.

MENU/HELP button

For displaying

adjustment and setting screens, and help screen.

INPUT button (W/Y)

For switching input mode 1, 2 or 3.

Focus ring

For adjusting the focus.

Zoom knob

For enlarging/ reducing the picture.

Indicators on the Projector

ON/STANDBY button

Lamp indicator

Temperature warning indicator

FOCUS/ZOOM indicator

HEIGHT ADJUST indicator

Remote control sensor

Red on Green on

Red blinks Abnormal (See page 54.) Green on Green blinks

Red on The lamp is shut down abnormally or

Off Red on

Orange blinks

Normal (Standby) Normal (Power on)

Normal The lamp is warming up or shutting down.

requires to be changed. (See page 54.)

Normal The internal temperature is abnormally

high. (See page 54.)

“1 FOCUS” or “3 ZOOM” is highlighted on the Setup Guide. (See page 27.)

“2 HEIGHT ADJUST” is highlighted on the Setup Guide. (See page 27.)

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

Side View

Introduction

Terminals

INPUT 1 terminal

Terminal for computer RGB and component signals.

USB terminal

Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.

AC socket

Connect the supplied Power cord.

Refer to “INPUT Terminals and Connectable Main Equipment” on page 21.

INPUT 2 terminal

Terminal for connecting video equipment with an S-video terminal.

INPUT 3 terminal

Terminal for connecting video equipment.

AUDIO INPUT

terminal

24 25

Exhaust vent

Kensington Security Standard connector

Rear adjust-

Intake vent

Remote control sensor

Using the Kensington Lock

• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

ment foot

Part Names and Functions (Continued)

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

ON/STANDBY button

For turning the power on and putting the projector into standby mode.

INPUT 1, 2, and 3 buttons

For switching to the respective input modes.

AUTO SYNC button

For automatically adjusting images when connected to a computer.

RESIZE button

For switching the screen size (NORMAL, BORDER, etc.).

PICTURE MODE buttons

For switching the picture mode.

Volume buttons

For adjusting the speaker sound level.

Note

• All the buttons on the remote control, except the MOUSE/Adjustment button, are made of luminous rubber, that is visible in the dark. (The luminous light weakens over time.)

Inserting the Lithium Battery

MENU/HELP button

For displaying adjustment

and setting screens, and help screen.

MOUSE/Adjustment

buttons (P/R/O/Q)

• For moving the computer cursor when connecting the projector USB terminal to the computer with RGB/ USB cable.

• For selecting menu items.

L CLICK/ENTER button

• For the Left click when

connecting the projector USB terminal to the computer with RGB/USB cable.

• For setting items selected or adjusted on the menu.

R CLICK/RETURN button

• For the Right click when

connecting the projector USB terminal to the computer with RGB/USB cable.

• For undoing an operation or returning to the previous display.

FREEZE button

For freezing images.

AV MUTE button

For temporarily displaying the black screen and turning off the sound.

While pressing the tab (1), pull the battery holder

(2).

Pull the battery holder.

Insert the supplied lithium battery (CR2025).

• Insert the lithium battery with the + side of the battery facing the + mark of the battery holder.

Insert the battery holder into the remote control.

+ mark

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Note

• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

When using the remote control

• Be sure not to drop, expose to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp.

Front view

Remote control signal transmitters

30°

Remote control

Rear view

Remote control sensor

Introduction

Remote control sensor

13n (4 m)

30°

Remote control signal

13n (4 m)

transmitters

30°

Notes the Use of the Lithium Battery

CAUTION The battery used in this device may present a risk of fire of chemical burn if mis-

treated. Do not recharge, disassemble, heat above 212°F (100°C) , or incinerate. Replace battery with the type CR2025 only. Use of another battery may present a risk of fire or explosion. Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose of in fire.

• See page 2 for caution on the lithium battery.

• Do not short-circuit, recharge, disassemble, or heat the lithium battery.

• Should the lithium battery leak, wipe the battery compartment clean, and then insert a new battery.

Replacement of lithium battery

• Replace with a new battery (CR2025) if remote control operation often fails.

• When disposing the battery, follow the recycling or disposal regulations in your community.

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

INPUT button

ENTER button

ON/STANDBY button

HEIGHT

ADJUST button

Zoom knob

Focus ring

ON/STANDBY button

INPUT 1 button

ENTER button

1. Place the projector facing a wall or a screen

_P. 18

2. Connect the projector to the computer and plug the power cord

into the AC socket of the projector

When connecting equipment other than the computer, see pages 24 and 25.

3. Press the ON/STANDBY button to turn the projector on

On the projector On the remote control

_PP. 21–25

_P. 26

4. Adjust the projected image with the Setup Guide

1 After the projector turns on, the Setup

Guide appears. (When “Setup Guide” is set to “On”. n page 45)

3 Angle (See page 28.)

• Adjust the projector angle using the HEIGHT ADJUST button.

Quick Start

HEIGHT ADJUST

button

4 Zoom (See page 28.)

• Adjust the projected image size using the

• Refer to the Setup Guide screen to adjust the focus, angle and zoom.

• Press TENTER to finish the Setup Guide.

Focus (See page 27.)

• Bring the projected image into focus using the focus ring.

zoom knob.

Zoom knob

zoom in

zoom out

5 After adjusting the focus, height and screen

size, press TENTER to finish the Setup

Focus ring

Guide.

_P. 27

5. Select the INPUT mode

Select the “INPUT 1” using the INPUT button on the projector or C INPUT 1 on the remote control.

projector

• When pressing the INPUT button on the projector, input mode switches in order of

INPUT1 INPUT2 INPUT3

• When using the remote control, press the CINPUT 1/DINPUT 2/EINPUT 3 button to

switch the INPUT mode.

On the

On the remote

control

On-screen display (RGB)

_P. 29

6. Turn the Power off

Press the ON/STANDBY button, then press that button again while the confirmation message is displayed, to put the projector into standby mode.

On the

projector

• While the cooling fan is running, the Adjustment buttons blinks. (When “Guide LEDs” is set to “On”. n page 48)

• Unplug the power cord from the AC outlet after the cooling fan stops.

On the remote

control

On-screen Display

_P. 26

+ 49 hidden pages