High Resolution Camera
User Manual
HCD-7010R/7020R/7030R
HCV-7010R/7020R/7030R
HCO-7010R/7020R/7030R
High Resolution Camera
User Manual
Copyright
©2017 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal
guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description.
■ HCD-70X0R/HCV-70X0R/HCO-70X0R SERIES
•NTSCMODEL |
•PALMODEL |
HCD-70X0R |
HCD-70X0RP |
HCV-70X0R |
HCV-70X0RP |
HCO-70X0R |
HCO-70X0RP |
■MODELDESCRIPTION
•HCX-70X0RX_
SIGNALSYSTEM
•SIGNALSYSTEM N→ NTSCMODEL P→ PALMODEL
safety information
|
|
|
|
|
|
CAUTION |
|
|
|
RISKOFELECTRICSHOCK. |
|
|
|
DONOTOPEN |
|
|
|
|
|
CAUTION: |
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER |
||
|
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO |
||
|
QUALIFIED SERVICE PERSONNEL. |
||
|
|
|
|
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
•To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.
•To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
WARNING
1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.
2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.
3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.
4.Securely plug the power cord into the power receptacle. insecure connection may cause fire.
5.When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
4_ safety information
6. |
Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled |
|
|
|
with water on top of the camera. doing so may cause personal injury due to fire, electric shock, |
|
|
|
or falling objects. |
|
|
7. |
Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric |
|
|
|
shock. |
● |
|
|
|
||
|
|
|
|
8. |
If any unusual smells or smoke come from the unit, stop using the product. in such case, |
safety |
|
|
|||
|
immediately disconnect the power source and contact the service center. continued use in |
|
|
|
|
|
|
|
such a condition may cause fire or electric shock. |
information |
|
9. |
If this product fails to operate normally, contact the nearest service center. never disassemble |
|
|
|
|
or modify this product in any way. (Hanwha Techwin is not liable for problems caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may cause fire or electric shock.
CAUTION
1.Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibrationor magnetic interference.
2.Do not install in a location subject to high temperature (over 55°C), low temperature (below -10°C(HCO-7070R:-30°C)), or high humidity. Doing so may cause fire or electric shock.
3.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4.Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or damage to the product.
5.Keep out of direct sunlight and heat radiation sources. It may cause fire.
6.Install it in a place with good ventilation.
7.Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CMOS image sensor.
8.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
9.The Mains plug is used as a disconnect device and shall stay readily operable at any time
10.Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.
English_5
safety information
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
1)This device may not cause harmful interference, and
2)This device must accept any interference received including interference that may cause undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interference.-Causing Equipment Regulations of ICES-003.
Correct Disposal ofThis Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.
6_ safety information
important safety instructions
1. |
Read these instructions. |
|
|
2. |
Keep these instructions. |
|
|
3. |
Heed all warnings. |
|
|
4. |
Follow all instructions. |
● |
|
|
|||
5. |
Do not use this apparatus near water. |
important |
|
|
|
||
6. |
Clean only with dry cloth. |
|
|
7. |
Do not block any ventilation openings. Install in accordance with the manufacturer’s |
safety |
|
|
instructions. |
|
|
|
|
|
|
8. |
Do not install near any heat sources such as radiators, heat registers, or other apparatus |
instructions |
|
|
a third grounding prong. The wide blade or the third prong is provided for your safety. If |
|
|
|
(including amplifiers) that produce heat. |
|
|
9. |
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug |
|
|
|
has two blades with one wider than the other. A grounding type plug has two blades and |
|
|
the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 24 Vac (50/60 Hz) min.0.37 A or 12 Vdc, min.0.41A.
16. If you use excessive force when installing the product, the camera may be damaged and malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.
English_7
important safety instructions
17.Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table.
This may cause damage to the product.
18.When installing the product, be careful not to allow the surface of the product to be stained with chemical substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.
19.If you install/disassemble the product in a manner that has not been recommended, the production functions/performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
20.Installing or using the product in water can cause serious damage to the product.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
8_ important safety instructions
contents
introduction |
10 |
Features |
|
10 |
11 |
Components and Accessories |
|
14 |
Component names and functions |
||
Installation |
17 |
Before installation |
|
17 |
17 |
Installation |
|
22 |
Adjusting the monitoring |
||
|
direction for the camera
Contents ●
connection |
24 |
Connecting to Monitor |
24 |
25 |
Connecting to Power |
27 |
Using Coaxial Communications |
|
cameraoperation |
29 |
Menu Configuration |
29 |
29 |
Menu Setup |
troubleshooting |
40 |
Troubleshooting |
40 |
|
|
specifications |
41 |
Specifications |
41 |
|
(HCD-7010R/7020R/7030R) |
43 |
Specifications |
|
|
(HCv-7010R/7020R/7030R) |
|
45 |
Specifications |
|
|
|
(HCO-7010R/7020R/7030R) |
|
47 |
Dimension |
English_9
introduction
Features
yy High Resolution
Use of a 4.1 mega pixel CMOS device provides clear pictures with a resolution of 2560x1440.
yy Excellent Sensitivity
-HCD-7010R/HCV-7010R/HCO-7010R Color : 0.26Lux (F1.8, 1/30sec)
B/W : 0Lux(IR LED on)
-HCD-7020R/HCV-7020R/HCO-7020R HCD-7030R/HCV-7030R/HCO-7030R Color : 0.27Lux (F2.0, 1/30sec)
B/W : 0Lux(IR LED on)
yy D-WDR
If an object has a large variance between bright and dark areas, it will keep bright areas bright and make selected dark areas bright, so that the overall brightness can be maintained.
yy Day&Night
This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and B/W mode operates in night-time conditions to enhance the definition of the image.
yy MiscellaneousFunctions
HLC(High Light Compensation), REVERSE , SHARPNESS and PRIVACY functions are provided.
yy Communication
AHD : ACP (AHD Coax Protocol), CVBS : Pelco-C (Coaxitron)
yy OSD
The camera’s OSD is complimented by 14 languages.
-English, German, Italian, French, Spanish, Russian, Czech, Polish, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese
10_ introduction
ComponentsandAccessories
Check if the following items are included in the product package.
<HCD-7010R/7020R/7030R>
introduction ●
Camera |
QuickManual |
Screws |
Template |
Video Output Cable
English_11
introduction
<HCV-7010R/7020R/7030R>
Camera |
QuickManual |
Template |
Tapping Screw |
MachineScrews |
LWrench |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Card-type moisture |
Video Output Cable |
|
absorbent |
||
|
12_ introduction
<HCO-7010R/7020R/7030R>
introduction ●
Camera |
QuickManual |
Screws |
|
|
|
|
|
|
Template |
Wrench |
Card-type moisture |
|
absorbent |
|||
|
|
Video Output Cable
English_13
introduction
Componentnamesandfunctions
HCD-7010R/7020R/7030R
9 |
3 |
2 |
|
|
1
5 |
|
4 |
6 |
|
8
7
1Dome Cover
2Shield Case
3Rotate base : control rotating angle of camera.
4Vari-focalLensModule:HCD-7010R : 2.8mm(F1.8) HCD-7020R : 4.0mm(F2.0) HCD-7030R : 6.0mm(F2.0)
5Function Setup switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item.
Switching between AHD and CVBS modes: Press the SET button for
more than 5 seconds.
6VideoOutputTerminaltoMonitor
7PanBase:Control panning angle of camera.
8PowerInputConnector
9Video Output Jack : Video signals are output through this port. Connect this port to the Video IN port of a AHD DVR.
IRLED:These infrared LED’s are controlled by the illumination sensor.IIIumination sensor : Detects incoming light to control the IR LED.
14_ introduction
HCV-7010R/7020R/7030R
9 |
|
|
3 |
2 |
|||
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
4 |
8
7
6 |
introduction ●
1Dome Cover
2Rotate base : control rotating angle of camera.
3Vari-focalLensModule:HCV-7010R : 2.8mm(F1.8) HCV-7020R : 4.0mm(F2.0) HCV-7030R : 6.0mm(F2.0)
4Function Setup switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item.
Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
5VideoOutputTerminaltoMonitor
6PanBase:Control panning angle of camera.
7PowerInputConnector
Video Output Jack : Video signals are output through this port. Connect this port to the Video IN port of a AHD DVR.
IRLED:These infrared LED’s are controlled by the illumination sensor.IIIumination sensor : Detects incoming light to control the IR LED.
English_15