Dishwasher
Installation manual
DW80R706* Series
DW8000R_DD68-00210A-00_EN.indd 1 |
|
|
4/25/2019 11:09:59 AM |
|
|
||
|
|
|
|
Contents
Contents
Safety instructions |
3 |
|
|
Important safety instructions |
3 |
Before using your dishwasher |
5 |
Installation |
6 |
|
|
Product dimensions |
11 |
Cabinet dimensions |
12 |
Specifications |
34 |
|
|
Scan the QR code* to view our helpful installation videos.
* Requires reader to be installed on your smartphone.
2 English
DW8000R_DD68-00210A-00_EN.indd 2 |
|
|
4/25/2019 11:10:00 AM |
|
|
||
|
|
|
|
Safety instructions
Throughout this manual, you will see Warning and Caution notes. The warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.
Important safety instructions
What the icons and signs in this installation guide mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in personal injury or property damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when using the dishwasher, follow these basic safety precautions:
NOTE
Indicates that a risk of personal injury or material damage exists.
These warning signs are here to prevent injury to you and others. Please follow them explicitly.
After reading this section, keep it in a safe place for future reference.
|
These installation instructions are intended for use by qualified installers. |
|
STOP |
If you are having problems installing this dishwasher |
|
U.S.A |
||
|
||
|
Please call: 1-800-SAMSUNG (726-7864) |
|
|
1-844-SAM-PAYS (726-7297) |
|
|
for assistance: www.samsung.com/us/support |
|
|
CANADA |
|
|
Please call: 1-800-SAMSUNG (726-7864) |
|
|
for assistance: www.samsung.com/ca/support (English) |
|
|
www.samsung.com/ca_fr/support (French) |
instructions Safety
SAVE THESE INSTRUCTIONS
English 3
DW8000R_DD68-00210A-00_EN.indd 3 |
|
|
4/25/2019 11:10:01 AM |
|
|
||
|
|
|
|
Safety instructions
instructions Safety
California Proposition 65 Warning
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Read all instructions before using the appliance.
Install and store the dishwasher inside, away from exposure to weather.
CAUTION
•Do not install the dishwasher near electrical components. Keep the dishwasher away from open flames.
•Do not install the dishwasher on a carpet as this is a fire hazard.
•Do not install the dishwasher in a location where the water may freeze (where the temperature falls below 32 °F (0 °C)). Frozen water in the hoses or pipes may damage the dishwasher.
•As with all equipment using electricity, water, and moving parts, potential hazards exist. To safely operate this appliance, become familiar with its operation and exercise care when using it.
The dishwasher must be properly grounded. Never connect it to an ungrounded outlet.
Prior to removal of original dishwasher and the installation of your new unit, make sure to switch off your circuit breaker. Do not connect the dishwasher until you have
completed the installation. Connecting the power cable is the last step when installing the dishwasher.
All wiring and grounding must be done in accordance with the electrical code applicable to the region.
GROUNDING INSTRUCTIONS
For a permanently connected appliance:
This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or more people are needed to move a dishwasher and avoid potential injuries.
CAUTION
•If the power cable is damaged, it must be replaced by the manufacturer, a service agent or similarly qualified person in order to avoid a hazard.
•Do not touch the power cable with wet hands.
•Do not connect another appliance to the same power outlet as the dishwasher.
SAVE THESE INSTRUCTIONS
4 English
DW8000R_DD68-00210A-00_EN.indd 4 |
|
|
4/25/2019 11:10:01 AM |
|
|
||
|
|
|
|
Make sure to use a new water supply line. Old lines are susceptible to breakage because they become hardened and may cause property damage due to a water leakage.
The dishwasher must be connected to a hot water supply with a temperature between 120 °F (49 °C)~149 °F (65 °C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 °F (65 °C) to prevent damage to dishes.
Ensure that the water supplied to the dishwasher does not freeze. Frozen water can damage the hoses, valves, pump, or other components.
Certified residential dishwashers are not intended for licensed food establishments.
(NSF/ANSI Standard 184 for Residential Dishwashers)
For a full list of safety information, please refer to the User Manual.
Before using your dishwasher
WARNING
Tip-Over Hazard
•Do not use the dishwasher until it is correctly installed.
•Do not push down on the dishwasher door when it is open.
•Do not place excessive weight on the dishwasher door when it is open.
Electric Shock Hazard
Failure to follow these instructions can result in death, fire, or electric shock:
•Electrically ground the dishwasher.
•Connect the ground wire to the green ground connector in the junction box.
•Do not use an extension cord.
To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.
instructions Safety
SAVE THESE INSTRUCTIONS
English 5
DW8000R_DD68-00210A-00_EN.indd 5 |
|
|
4/25/2019 11:10:02 AM |
|
|
||
|
|
|
|
Installation
Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you are not at risk of injury when washing dishes.
STEP 1 Check the parts and tools
Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process.
Parts required
Provided with the dishwasher. Check when you unbox the dishwasher in STEP 5.
2 Installation |
Kick Plate |
6 screws |
Protective sticker |
brackets |
|
(for the Kick plate & |
|
|
|
Bracket Installation) |
|
Paper ruler |
Nut connector & |
6 Plastic caps |
|
seal (for 3/4" 90° |
|
|
fitting) |
|
Installation
6 English
DW8000R_DD68-00210A-00_EN.indd 6 |
|
|
4/25/2019 11:10:06 AM |
|
|
||
|
|
|
|
Not provided
Power cable |
Twist on wire |
Strain relief |
Electrical tape & |
|
connector |
|
Standard duct tape |
Hot water supply |
90° Fitting (3/4") |
Tube fittings |
Hose clamp |
line |
|
|
|
Air gap |
Rubber connector |
NOTE
For the hot water supply line – We strongly recommend using 3/8" minimum O.D. copper tubing with a compression fitting or a flexible stainless steel braided hot water supply line.
[Warning: Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube fitting.]
You also need a 90° Fitting with 3/4" N.P.T. external pipe threads on one end and a fitting sized to fit your hot water supply line (copper tubing/compression fitting or braided hose) on the other.
For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes may require the cable to have a BX style metal jacket.
Installation
English 7
DW8000R_DD68-00210A-00_EN.indd 7 |
|
|
4/25/2019 11:10:15 AM |
|
|
||
|
|
|
|
Installation
Tools required
Installation
Electric drill |
Safety glasses |
Gloves |
Flashlight |
Adjustable wrench |
|
Wire stripper |
|
Pliers |
|
Nipper |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tape measure |
Pencil |
Phillips screwdriver |
Flat screwdriver |
Tubing cutter |
Cutting knife |
Hole saw |
Level |
Torx t20 |
Hex L-wrench |
8 English
DW8000R_DD68-00210A-00_EN.indd 8 |
|
|
4/25/2019 11:10:32 AM |
|
|
||
|
|
|
|
NOTE
New installation
If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place.
Replacement
If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Replace the existing connections as necessary.
STEP 2 Select the best location for the dishwasher
The following criteria are important to ensure the best location for the dishwasher:
•The location must have a solid floor that is able to support the weight of the dishwasher.
•The location must be near a sink with easy access to the water supply, drain, and electrical outlet.
NOTE
For the drain to operate properly, the dishwasher should be installed within 9.8 ft (3 m) of the sink.
•The location must let you load your dishes into the dishwasher easily.
•The location must have sufficient space for the dishwasher door to open easily and provide enough space between the dishwasher and the cabinet sides (at least 0.1 in (2 mm)).
NOTE
If the dishwasher is installed in a corner, ensure that the side of the dishwasher is more than 2 in. (50 mm) from the wall or cabinet to its right or left.
•The wall at the back must be free of obstructions.
•Make sure the cabinet for the dishwasher is secured to the floor. If the cabinet is not secured, it may increase noise when the dishwasher is operating.
Installation
English 9
DW8000R_DD68-00210A-00_EN.indd 9 |
|
|
4/25/2019 11:10:33 AM |
|
|
||
|
|
|
|
Installation
Installation
If this is a new installation, follow these steps:
1.Using a 21/2 inch hole saw, cut a hole into the side of the cabinet that holds the sink as shown in Figure 1-1 below.
2.If the base inside the sink cabinet is raised above the kitchen floor and is higher than the connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet
as shown in Figure 1-2.
NOTE
Depending on where your electrical outlet is, you may need to cut a hole in the opposite cabinet side.
Figure 1-1 |
Figure 1-2 |
The hole for the water supply line, drain hose and power cables.
CAUTION
Make sure the edges of the cabinet hole are smooth before you insert the drain hose through the hole. Sharp edges from the cabinet hole may cause damage to the drain hose, resulting in a leak from the hose.
10 English
DW8000R_DD68-00210A-00_EN.indd 10 |
|
|
4/25/2019 11:10:35 AM |
|
|
||
|
|
|
|
Product dimensions
Front view
DW80R7060 Series |
|
DW80R7061 Series |
|
|
237/8" (605 mm) |
|
237/8" (605 mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
35"-33⅞ |
35"-33⅞ |
890-(860 |
890-(860 |
mm) |
mm) |
Junction box |
Junction box |
Side view |
|
DW80R7060 Series |
DW80R7061 Series |
|
275/16" (693 mm) |
mm) (107 "5/14 |
|
mm) (140 "4/35 mm) (60 "2/12 |
23/4" (70 mm) |
|
21/2" (60 mm) |
201/2" (520 mm) |
201/2" (520 mm) |
You must arrange the |
|
|
|
25" (636 mm) |
25" (636 mm) |
water supply line, |
|
|
power cable and drain |
|
|
hose in the space |
|
|
behind the dishwasher. |
English 11
Installation
DW8000R_DD68-00210A-00_EN.indd 11 |
|
|
4/25/2019 11:10:36 AM |
|
|
||
|
|
|
|
Installation
Cabinet dimensions
24" (610 mm) minimum
24" (610 mm) minimum
Installation
12 English
mm) 897-(867 35⅓"-34⅛
NOTE
This dishwasher is designed to be enclosed on the top and on both sides by a standard residential kitchen cabinet unit.
The installation cabinet must be clean and free of any obstructions.
The cabinet must be at least 24 inches wide,
24 inches deep, and 341/8 inches high. For the front door of the dishwasher to be flush with the leading edge of the counter top, the counter top must be at least
25 inches deep.
DW8000R_DD68-00210A-00_EN.indd 12 |
|
|
4/25/2019 11:10:36 AM |
|
|
||
|
|
|
|
STEP 3 Check water supply requirements and cautions
•The hot water supply line pressure must be between 20~120 psi (140~830 kPa).
•Adjust the water heater to deliver water between 120 °F (49 °C)~149 °F (65 °C).
-The dishwasher must be connected to a hot water supply between 120 °F
(49 °C)~149 °F (65 °C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 °F (65 °C) to prevent damage to dishes.
-Ensure that the water supply valve is turned off before connecting the hot water supply line to the dishwasher.
-Seal the hot water supply line connections using teflon tape or sealing compound to stop any water leakage.
-The drain hose connected to the dishwasher must be run through the hole in the side wall so it can be connected to the drain outlet of the sink. When you install the dishwasher, ensure there is nothing on the drain hose and be careful not to damage it during the installation process.
Figure 2
Power cable
Hot Water
Supply Line
4¼-6¼ in. (110-160 mm)
Inlet valve
Dishwasher bottom
English 13
Installation
DW8000R_DD68-00210A-00_EN.indd 13 |
|
|
4/25/2019 11:10:37 AM |
|
|
||
|
|
|
|
Installation
STEP 4 Check the electrical requirements and cautions
The electrical requirements for the dishwasher are as follows:
•In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes.
•In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/ Provincial and Municipal codes and/or local codes.
•For cable direct connections.
-Use flexible, armored or non-metallic sheathed, copper wire with a grounding wire that meets the wiring requirements for your local codes and ordinances.
-Use the strain relief method provided with the wiring junction box or install a U.L.- listed/CSA-certified clamp connector to the wiring junction box. If using conduit, use a U.L.-listed/CSA-certified conduit connector.
Figure 3
Power cable 21/2-31/2 in. (64-89 mm)
Hot Water
Supply Line
Installation
Power cable channel |
Dishwasher bottom |
|
14 English
DW8000R_DD68-00210A-00_EN.indd 14 |
|
|
4/25/2019 11:10:37 AM |
|
|
||
|
|
|
|
STEP 5 Unpacking and inspecting the dishwasher
Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We recommend that you retain all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the packing materials prior to disposal.
Unpacking
1. Position the carton right-side-up with top arrows pointing upwards.
2.Unbuckle or cut the straps securing the packaging.
3. Unpack the product packaging with care.
4. Put the straps and all of the packing |
Kick plate |
|
materials from around the dishwasher |
||
|
||
inspecting them for any signs of |
|
|
damage. |
|
5. Locate and set aside the dishwasher's kick plate. The Kick plate is attached to packing material of the dishwasher.
6.Lift the dishwasher from the packing tray, and then place it on the floor.
CAUTION
• ALWAYS LIFT THE DISHWASHER TO MOVE IT. Sliding it over rough surfaces can damage the dishwasher’s feet and sliding the feet over finished surfaces can, in some cases, damage that finish or the underlying surface.
• Use caution, and do not grab the upper air duct when moving the dishwasher.
7.There is also packing inside the dishwasher that you may want to leave in place until the dishwasher is installed.
8.DO NOT, under any circumstances, remove the sound-absorbent padding that surrounds the exterior of the tub of the dishwasher.
Installation
English 15
DW8000R_DD68-00210A-00_EN.indd 15 |
4/25/2019 11:10:39 AM |
Installation
Installation
Inspecting
Mechanical
1.Check the plastic base assembly to ensure that it is intact
2.Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level and secure the dishwasher.
3.Check all the visible components on the bottom of the dishwasher to ensure they are intact and secure.
4.Check the door latch, the operation of the hinges, and confirm the door is properly secured to the dishwasher.
Plumbing
1.Check the hot water connection on the back left-side of the base of the dishwasher. The mounting plate should be secured to the back of the base, the threads inside the connection should be smooth and shiny, and the area should be clean and free of any debris.
2.Make sure the dishwasher and the accessories are all included in the package to ensure these assemblies are not cracked and that all connections are secure.
3.Check the drain hose for any holes or deformities that could allow a water leak during draining.
Electrical
1.Confirm the junction box cover is secured to the junction box on the front right-side of the base of the dishwasher.
2.Confirm the electrical box was not damaged during shipping and that it is secured to the base of the dishwasher.
Appearance
1.Confirm there are no dents or scratches on the front of the dishwasher.
2.Check the edges of the doors for any roughness or cracking.
3.Check the control panel to ensure it is clear and unscratched, and that all the control markers are in their proper places.
Parts
Confirm you have all the parts listed in STEP 1 on page 6.
16 English
DW8000R_DD68-00210A-00_EN.indd 16 |
|
|
4/25/2019 11:10:39 AM |
|
|
||
|
|
|
|
STEP 6 Preparing the dishwasher
1.Attach the protective sticker (A).
-To prevent damage, put the protective sticker on the bottom of the counter top as shown in the picture.
NOTE
•Before putting the protective sticker, clean the counter top as shown in the picture.
•For information, the length of the protective sticker is 26 inches (660 mm).
A |
2.Ensure that the circuit breaker and water supply valve are turned off before proceeding with the following steps.
CAUTION
Before you move or lay down the dishwasher for installation, make sure to adjust the height of the legs so the legs are as short as possible. This prevents the legs from breaking. Level the dishwasher by adjusting the height of the legs after you have the dishwasher in place.
Installation
English 17
DW8000R_DD68-00210A-00_EN.indd 17 |
|
|
4/25/2019 11:10:40 AM |
|
|
||
|
|
|
|
Installation
3.Use the provided nut connector to connect the water hose to the dishwasher. Follow these steps:
01
A |
B
02 |
03 |
|
E |
C D F
01 Disconnect the 90° fitting (A) from the hose (B).
02 Remove the seal (C) and the nut (D) from the 90° fitting.
03 From the provided nut connector, separate the seal (E) and the nut (F), and then assemble them to the 90° fitting as shown in the figure. You must insert the smaller side of the seal.
|
4. Then, insert the 3/4" 90 degree fitting into the inlet valve (See Figure 4-B). Tighten until |
|
|
the 3/4" fitting is tight. Do not over tighten. |
|
|
5. Detach the Velcro strips that secure the drain hose to the back of the dishwasher. Roll- |
|
|
out the hose. Make sure there are no kinks and that the hose is not bent at any extreme |
|
|
angles that could constrict the flow of water. |
|
Installation |
6. Remove the junction box cover located at the bottom front right of the dishwasher |
|
using a screwdriver, and then Install the strain relief (Figure 4-C). Make sure to keep |
||
|
||
|
the junction box cover you removed. It is used in STEP 11, Wiring Connections. |
|
|
7. If the countertop is made of wood or a material that is not damaged by drilling, attach |
|
|
the two (2) Installation brackets that were supplied with the dishwasher using the |
|
|
supplied screws (Figure 4-A). They will be used in STEP 9, Securing the Dishwasher. |
|
|
If the drain hose needs to go to the |
|
|
right of the dishwasher, secure the |
|
|
drain hose into the drain hose bracket, |
|
|
mounted on the base. |
|
|
The drain hose bracket can be adjusted |
|
|
in 3 positions. To adjust the height |
|
|
of the drain hose bracket, gently |
|
|
squeeze the bracket and turn it too the |
|
|
left. Insert the bracket in the desired |
|
|
position and turn it to the right to lock |
|
|
it into place. |
18 English
DW8000R_DD68-00210A-00_EN.indd 18 |
|
|
4/25/2019 11:10:42 AM |
|
|
||
|
|
|
|
Figure 4
A
A A’
B |
C |
|
|
|
Junction box |
|
Strain relief |
|
90° fitting |
CAUTION
Do not overtighten the 90° Fitting. (Below 280 lb·in (31.6 N·m)) Doing so may damage the water inlet valve and cause a water leak.
Installation
English 19
DW8000R_DD68-00210A-00_EN.indd 19 |
|
|
4/25/2019 11:10:49 AM |
|
|
||
|
|
|
|
Installation
STEP 7 Placing the dishwasher and connecting the hot water supply line
1. |
Adjust the three leveling legs at the bottom of the dishwasher after measuring the |
|
height of the cabinet opening from under the countertop to the floor. (See STEP 8, |
|
Leveling the Dishwasher.) |
2. |
Locate the hot water supply line and the power cable. |
3. |
Place the dishwasher so that the hot water supply line is in the left side and the power |
|
cable is in the right channel of the base of the dishwasher. The right-side channel for |
|
the power cable has a built-in hook on the base so that you secure the power cable. |
4. |
Pull the drain hose through the hole in the sink cabinet side wall. Keep it free of kinks. |
5. |
Make sure the hot water supply line is not twisted, and then connect the hot water |
|
supply line to the fitting joint. |
6. |
Slide the dishwasher carefully into the installation space. If possible, gently pull any |
|
excess lengths of water supply line, drain hose, or power cable back as you move the |
|
dishwasher. Get a second person to help you do this if necessary. |
|
CAUTION |
Do not place the dishwasher on the water supply line, drain hose, or power cable. Also, |
|
make sure they are not folded or twisted. |
|
• Make sure the supply line is properly connected. |
|
|
Wrap Teflon tape around every connection to prevent water leaks. |
Installation |
Make sure the side gaskets are inserted seamlessly. Otherwise, it may increase noise |
operating. |
when the dishwasher is operating.
• Make sure both side gaskets are 13/16" to 1" (20-25 mm) backward from the front end of the kitchen cabinet. Less distance may increase noise when the dishwasher is
20 English
DW8000R_DD68-00210A-00_EN.indd 20 |
|
|
4/25/2019 11:10:50 AM |
|
|
||
|
|
|
|
Figure 5
Side gasket
Side gasket
1 inch
Drain hose
Hot Water Supply Line
Power cable
Inlet valve
Hot Water Supply Line
Elbow (3/4" (9.5 mm))
CAUTION
Do not overtighten the 90° Fitting.
Doing so may damage the water inlet valve and cause a water leak.
Junction box
built-in hook
Make sure the dishwasher is positioned to the center.
Installation
English 21
DW8000R_DD68-00210A-00_EN.indd 21 |
|
|
4/25/2019 11:10:51 AM |
|
|
||
|
|
|
|
Installation
Installation
STEP 8 Leveling the dishwasher
1.Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level.
See the first note below for instructions on adusting the height of the front legs.
2.Use the level to check if the dishwasher is level front to back, as shown in the figure to the right.
If the dishwasher is not level front to back, adjust the height of the rear leg until the dishwasher is level.
See the second note below for instructions on adusting the the rear leg.
NOTE
To prevent leaks from the door, make sure that the front of the dishwasher is not lower than the back.
3.Open the door of the dishwasher and check if both the tub and door clearances are correct.
If not, rotate the leveling legs on the bottom front of the dishwasher. You can aslo check this by placing a level against an inside front vertical surface of the tub.
22 English
DW8000R_DD68-00210A-00_EN.indd 22 |
|
|
4/25/2019 11:10:53 AM |
|
|
||
|
|
|
|