Saeco 10001872, 10001864, 10001863, 10001860, 10001257 Operating And Maintenance Manual

...

0 (0)

Type SUP030ND Cod.15001585 Rev.00 del 15-10-08

Saeco International Group S.p.A.

Via Torretta, 240 I-40041 Gaggio Montano, Bologna Tel: + 39 0534 771111

Fax: + 39 0534 31025 www.saeco.com

The manufacturer reserves the right to change the features of the product without prior notice.

Le producteur se réserve le droit d“appor ter toutes modifications sans préavis.

Operation and maintenance manual

Before using the machine, please read the attached operating instructions.

Carefully read the safety rules

Mode d'emploi

Veuillez lire attentivement le mode d'emploi

(notamment les consignes de sécurité) avant d'utiliser l'appareil.

FOR HOUSEHOLD USE ONLY

USAGE DOMESTIQUE SEULEMENT

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons do not immerse

cord, plugs, or appliance in water or other liquid.

4. Close supervision is necessary when the appliance is used by or near

children.

5. Unplug from outlet when not in use and before cleaning. Allow to cool before

putting on or taking off parts, and before cleaning the appliance.

6. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

7. The use of accessory attachments not recommended by the appliance

manufacturer may result in fire, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated oven.

11. Always attach plug to appliance first, then plug cord into wall outlet. To

disconnect, turn any control to “off”, then remove plug from wall outlet.

12. Do not use appliance for other than intended use.

13. Warning! Do not open the service door during the brewing, dispensing,

washing or rinse

14. Save these instructions.

SAVE THESE INSTRUCTIONS

CAUTION

This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate

corresponds with your voltage.

2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during

operation.

4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft

cloth dampened with water.

5 For optimal taste of your coffee, use purified or bottled water. Periodic

descaling is still recommended every 2-3 months.

6 Do not use flavored or carmelized coffee.

INSTRUCTIONS FOR THE POWER

SUPPLY CORD

A. A short power-supply cord (or detachable power-supply cord) is to be

provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.

B. Longer detachable power-supply cords or extension cords are available and

may be used if care is exercised in their use.

C. If a long detachable power-supply cord or extension cord is used,

1. The marker electrical rating of the detachable power-supply cord or

extension cord should be at least as great as the electrical rating of the appliance

2. If the appliance is of the grounded type, the extension cord should be a

grounding-type 3-wire cord, and

3. The longer cord should be arranged so that it will not drape over the counter

top or table top where it can be pulled on by children or tripped over.

2 INDEX

GENERAL INFORMATION .................................................................................................................3

MACHINE .......................................................................................................................................4

ACCESSORIES .................................................................................................................................................4

INSTALLATION ...............................................................................................................................5

STARTING THE MACHINE .....................................................................................................................................5

SETTING THE LANGUAGE .....................................................................................................................................6

INTENZA WATER FILTER ......................................................................................................................................7

DISPLAY ........................................................................................................................................8

AROMA OPTI-DOSE ...........................................................................................................................................8

ADJUSTMENTS ..............................................................................................................................9

MILK CONTAINER .............................................................................................................................................9

DRIP TRAY HEIGHT ADJUSTMENT ............................................................................................................................ 9

COFFEE STRENGTH .........................................................................................................................................10

SAECO ADAPTING SYSTEM .................................................................................................................................10

BEVERAGE DISPENSING................................................................................................................11

BREWING WITH WHOLE BEANS ............................................................................................................................11

BREWING WITH PRE-GROUND COFFEE ....................................................................................................................12

LATTE MACCHIATO .........................................................................................................................................13

ESPRESSO MACCHIATO .....................................................................................................................................15

CAPPUCCINO ................................................................................................................................................15

HOT MILK ...................................................................................................................................................16

HOT WATER .................................................................................................................................................16

BEVERAGE PROGRAMMING...........................................................................................................17

1. MANUAL PROGRAMMING ...............................................................................................................................17

PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU ........................................................................................... 17

PROGRAMMING THE MACHINE......................................................................................................19

MACHINE SETTINGS ........................................................................................................................................20

LANGUAGE ...............................................................................................................................................................20

CUP WARMING SURFACE ................................................................................................................................................21

WATER FILTER ...........................................................................................................................................................21

RINSE CYCLE .............................................................................................................................................................22

WATER HARDNESS - INTENZA AROMA SYSTEM ....................................................................................................................... 22

ACOUSTIC ALARM .......................................................................................................................................................23

MAINTENANCE MENU ......................................................................................................................................24

MILK CLEANING CYCLE ..................................................................................................................................................24

COFFEE CLEANING CYCLE ...............................................................................................................................................25

MILK WASH CYCLE ......................................................................................................................................................26

DESCALING CYCLE .......................................................................................................................................................29

CLOCK SETTINGS ...........................................................................................................................................31

TIME SETTING ...........................................................................................................................................................31

DATE SETTING ...........................................................................................................................................................32

TIME FORMAT............................................................................................................................................................32

STANDBY SETTING ..........................................................................................................................................33

ENERGY SAVING .........................................................................................................................................................33

TIMER SETTING ..........................................................................................................................................................33

SPECIAL FUNCTIONS ........................................................................................................................................35

FACTORY SETTINGS .....................................................................................................................................................35

COFFEE OF THE WORLD .................................................................................................................................................36

BEVERAGE COUNTERS ...................................................................................................................................................37

CLEANING AND MAINTENANCE .....................................................................................................38

MAINTENANCE DURING OPERATION ........................................................................................................................ 38

GENERAL MACHINE CLEANING .............................................................................................................................38

MILK CONTAINER MAINTENANCE AND CLEANING .........................................................................................................39

CLEANING THE BREW GROUP. .............................................................................................................................41

GRINDER MAINTENANCE ....................................................................................................................................42

STORING THE MACHINE ....................................................................................................................................43

RESTARTING THE MACHINE ................................................................................................................................43

ERROR CODES .............................................................................................................................44

SAFETY RULES ............................................................................................................................45

TECHNICAL DATA .........................................................................................................................47

This coffee machine is intended for preparing espresso by using either coffee beans or ground coffee. It includes an automatic device for preparing milk beverages and a hot water dispenser. This machine is designed for domestic use only, and is not suitable for continuous heavy or professional use.

Warning: No liability is assumed for any damage caused by:

• Incorrect use not in accordance with the intended uses;

• Repairs not carried out by authorized customer service centers;

• Tampering with the power cord;

• Tampering with any part of the machine;

• The use of non-original spare parts and accessories;

• Failure to descale the machine or use at temperatures below 0°C (32°F).

IN THESE CASES, THE WARRANTY IS NOT VALID.

Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee machine. For further information or if you experience problems not completely or sufﬁ ciently addressed in these instructions, please contact an authorized service center.

KEEP THESE INSTRUCTIONS

A WARNING TRIANGLE DRAWS ATTENTION TO ALL THE INSTRUCTIONS THAT ARE IMPORTANT FOR USER SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO AVOID SERIOUS INJURY!

HOW TO USE THESE OPERATING INSTRUCTIONS

GENERAL INFORMATION

Cappuccinatore

maintenance kit

Pre-ground coffee

scoop

Brew group cleaning

tablets

Water hardness

test strip

Grinder

adjustment key

Lubricant for the

brew group

Detergent for cleaning

milk container

Intenza water ﬁ lter

Descaling

solution

ACCESSORIES

Control panel

SBS dial

MACHINE

Pre-ground bypass doser

Brew group

Dregdrawer

Socket for power cord

Open coffee bean hopper button

Coffee bean hopper

Cup warming surface

Power button

Service door

Coffee bean hopper lid

Drip tray

Button for raising/lowering the drip tray

Dispensing head

Drip tray + grill

Compartment for milk container

Hot water spout

Water tank

Milk compartment button

1 2 3

INSTALLATION

Insert the plug into the socket located on the back of the machine and insert the other end into a power outlet with suitable current.

Place a container beneath the hot water spout.

Open the coffee bean hopper by pressing the button on the lid. Fill the bean hopper with coffee beans.

Close the lid pushing it down completely.

Remove the water tank. We recommend installing the water ﬁ lter (see page 7).

Press the power button to the “On” position.

Make sure the power button is not pressed and the machine is turned off.

Fill the tank with fresh drinking water. Do not exceed the “max” level indicated on the water tank. Once ﬁ lled place the tank back into the machine.

STARTING THE MACHINE

BEFORE PERFORMING ANY OPERATION, COMPLETE THE INSTALLATION (PAGES 6 – 7).

TO ADJUST THE WATER HARDNESS LEVEL AND SET THE INTENZA AROMA SYSTEM SEE THE «WATER HARDNESS MENU» ON PAGE 22.

BEFORE A LONG PERIOD OF INACTIVITY, AND BEFORE THE MACHINE IS RESTARTED, PLEASE CHECK THE RELEVANT INFORMATION IN THE CLEANING AND MAINTENANCE SECTION.

press ok

boiler filling

Press the to prime the water circuit. The machine will stop automatically.

warming up

please wait

rinsing

please wait

strong aroma

espresso coffee 08:33

When the priming is completed, the machine will warm up.

Once the heating phase is completed, a small quantity of water is dispensed. Wait for this cycle to be completed automatically. Refer to page 22 to enable/disable the function.

The machine is now ready for use.

INSTALLATION

1 2

SETTING THE LANGUAGE

When the machine is switched-on for the ﬁ rst time, it requires the selection of the desired language. This allows you to adjust the parameters of the beverages to the typical parameters of the country where the machine is used. This is why some languages are differentiated also by country.

english

language

Choose the desired language by navigating the click wheel with your ﬁ nger.

When the desired language is displayed, press

. The machine now displays the messages in the selected language.

english

language

Remove the small white ﬁ lter from the tank and store it in a dry place sheltered from dust.

Fill the tank with fresh drinking water and reinsert it into the machine.

Set the Intenza Aroma System: A = Light water B = Medium water (standard) C = Hard water For further details see page 22.

INTENZA WATER FILTER

To improve the quality of the water you use, and extend the life of your machine at the same time, it is recommended that you install the water ﬁ lter. After installation, go to the water ﬁ lter menu to initialize (see programming). By activating the water ﬁ lter, the machine informs the user when the water ﬁ lter must be replaced.

Remove the water ﬁ lter from its packaging, immerse it vertically (with the opening facing upwards) in cold water and gently press its sides so as to let the air bubbles out.

Insert the ﬁ lter in the empty tank. The reference mark and the groove must match. Push ﬁ rmly until it is completely inserted.

NOTE: If the Intenza water ﬁ lter is not available, insert the small white ﬁ lter previously removed (see point 1) into the tank.

Place a container beneath the hot water spout.

Please refer to the ﬁ lter initialization as described on page 21.

• Press the button twice to make 2 cups. This operation can be performed until the grinding is complete.

Press twice

It is possible to choose three aroma options (strong, medium and mild) by pressing the

button. These indicate the quantity of coffee the machine grinds for each beverage. This button is also used to select the pre-ground coffee function.

DISPLAY

Programming menu

AROMA OPTI-DOSE

strong aroma

espresso coffee 08:33

Milk button

Brew button

Hot water button

strong aroma

espresso coffee 08:33

strong aroma

double espresso 08:33

• To brew 2 cups, the machine dispenses the ﬁ rst coffee and brieﬂ y interrupts dispensing in order to grind the second serving of coffee.

Coffee dispensing is then restarted and completed. If a milk beverage has been chosen, the machine

automatically dispenses the milk.

strong aroma

espresso coffee 08:33

SELECT THE DESIRED AROMA BEFORE DISPENSING THE BEVERAGE.

medium aroma

espresso coffee 08:33

mild aroma

espresso coffee 08:33

pre-ground

espresso coffee 08:33

Click wheel

Aroma Opti-Dose

Open the milk compartment by pressing the button and remove the milk container.

Remove the cover and pour in the milk. DO NOT EXCEED THE MAXIMUM LEVEL shown in the ﬁ gure.

Replace the lid on the container and place it back in the milk compartment. Make sure to carefully close the compartment.

21 3

To raise the drip tray, press lightly on the lower part of the button. To lower the tray, press lightly on the upper part of the button; when the desired height is reached, release the button.

DRIP TRAY HEIGHT ADJUSTMENT

MILK CONTAINER

ADJUSTMENTS

Adjust the drip tray to the appropriate cup size before selecting the beverage.

WARNING! DO NOT OPEN THE SERVICE DOOR DURING THE BREWING, DISPENSING, WASHING OR RINSE CYCLE.

The container with the cappuccinatore must be ﬁ lled before preparing any milk beverage. Use only fresh milk. Do not use milk after the best-before date.

(Important! Refer to the instructions for maintenance and cleaning of the cappuccinatore on page 39-40).

MEDIUM

COFFEE

STRONG COFFEE

MILD

COFFEE

SBS adjusts the fullness of the brewed coffee, and can even be adjusted while brewing. Any adjustment has an immediate effect on the brewing coffee.

COFFEE STRENGTH

SBS – SAECO BREWING SYSTEM

The SBS dial has been carefully designed to give your coffee the fullness and intensity you desire. Simply turn the dial, and you will notice that the coffee brewed will adjust to the setting selected.

ADJUSTMENTS

SAECO ADAPTING SYSTEM

Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The Saeco coffee machine is equipped with a self-adjusting system that allows the use of all types of coffee beans available on the market (not including ﬂ avored or carmelized).

• The machine automatically adjusts itself in order to optimize the extraction of the coffee, ensuring perfect compression of the beans to obtain a creamy espresso coffee that is able to release all the aromas, regardless of the type of coffee used.

• The optimization process is a learning process that requires the brewing of a certain number of coffees to allow the machine to adjust the compactness of the ground coffee.

1 2 3

THE DISPENSING OF COFFEE, HOT WATER AND MILK MAY BE STOPPED AT ANY TIME BY PRESSING THE BUTTON AGAIN.

THE DISPENSED MILK CAN REACH HIGH TEMPERATURES: THERE IS A DANGER OF SCALDING. DO NOT TOUCH IT WITH BARE HANDS.

USE ONLY FRESH MILK. DO NOT USE IT AFTER THE EXPIRATION DATE ON THE PACKAGE.

Check that all containers are clean by following the "Cleaning and Maintenance" instructions on page 38.

WHEN YOU HAVE FINISHED PREPARING BEVERAGES CONTAINING MILK, PROCEED BY CLEANING THE CONTAINER AND THE MACHINE’S CIRCUIT.

To brew 2 cups, the machine dispenses the ﬁ rst coffee, and brieﬂ y interrupts dispensing in order to grind the second coffee dose. Coffee dispensing is then restarted and completed. If a milk beverage has been chosen, the machine automatically manages milk dispensing.

BREWING WITH WHOLE BEANS

Select the coffee aroma by pressing the

button one or

more times.

Press the

button once for 1 cup and twice for 2 cups. The selected beverage will be brewed.

BEVERAGE DISPENSING

This procedure shows how to dispense an espresso. To dispense another type of coffee, select it by sliding the click wheel with a ﬁ nger. Use appropriate espresso or coffee cups so that the coffee will not overﬂ ow.

The machine dispenses automatically according to the quantity determined by the manufacturer. It is possible to customize this quantity (see page 17).

strong aroma

espresso coffee 08:33

strong aroma

espresso coffee 08:33

brewing in progress

espresso coffee

Select the desired beverage by navigating the click wheel with your ﬁ nger.

1 2 3

BREWING WITH PRE-GROUND COFFEE

Pre-ground coffee must be scooped into the bypass doser next to the coffee bean hopper. Only use coffee that is ground speciﬁ cally for espresso machines and never coffee beans or instant coffee.

WARNING: PUT PRE-GROUND COFFEE IN THE BYPASS DOSER ONLY WHEN YOU WISH TO DISPENSE THIS TYPE OF BEVERAGE.

INSERT ONLY ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE DISPENSED AT THE SAME TIME.

Select the function by pressing the

button one or more times. Press the

button.

one scoop of ground coffee into the bypass doser using the measuring scoop provided.

Note:

• After 1 minute from when the "add preground coffee" message appears (3), if brewing has not started the machine will return to the main menu and dump any inserted coffee into the dregdrawer.

• If no pre-ground coffee is poured into the bypass doser, only water will be dispensed

• If 2 or more scoops of coffee are added, the machine will not dispense the beverage and the coffee in the bypass doser will be dumped into the dregdrawer.

The example given below shows how to brew an espresso using pre-ground coffee. The customized option of using pre-ground coffee is shown on the display.

strong aroma

espresso coffee 08:33

Select the desired beverage by navigating the click wheel with your ﬁ nger.

pre-ground

espresso coffee 08:33

A message appears, reminding the user to pour ground coffee in the bypass doser.

add pre-ground coffee

espresso coffee

Press the button to start brewing.

brewing in progress

espresso coffee

BEVERAGE DISPENSING

1 2 3

4 5 6

If the user wishes to continue preparing other drinks the machine will keep the “rinsing milk circuit” signal active.

After 20 minutes of inactivity, the machine requires the user to perform a rinsing cycle as described in step 7. If the machine is turned off immediately after dispensing a milk beverage, the next time the machine is turned on it will require the user to perform a rinsing cycle.

Note: Before performing the “milk rinsing circuit” function make sure that:

1. a large enough container is positioned under the dispensing head;

2. the water tank contains a sufﬁ cient quantity of water.

After 14 days from the ﬁ rst dispensing of a milk-based beverage, the message “milk circuit washing” is displayed; it is advisable to clean the milk circuits as shown on page 26.

After another 7 days the machine stops dispensing milk-based beverage and the milk circuits must be washed; during this phase, coffee and hot water may be dispensed.

milk circuit washing

espresso coffee 08:33

After this, the machine allows you to dispense more milk if you wish. This option remains active for approx. 3 seconds. To activate it, press the

button. Once the desired

quantity has been reached, press the

button again to stop dispensing.

LATTE MACCHIATO

Fill the milk container

strong aroma

espresso coffee 08:33

Press the button.

strong aroma

latte macchiato 08:33

Select latte macchiato by navigating the click wheel with your ﬁ nger.

strong aroma

latte macchiato 08:33

Select the aroma by pressing the

button one or more times.

brewing in progress

latte macchiato

Press the button once for 1 cup and twice for 2 cups. The latte macchiato will be brewed.

add milk?

latte macchiato

The machine will propose cleaning the milk circuits. Press the

button to clean the

internal circuits.

rinsing milk circuit

latte macchiato 08:33

SEE INSTRUCTIONS ON PAGE 39-40 FOR OPTIMAL MILK DISPENSING.

WARNING! DO NOT OPEN THE SERVICE DOOR DURING THE BREWING, DISPENSING, WASHING OR RINSE CYCLE.

7 8

Wait for the cycle to be completed. After this, the machine returns to the main menu.

Remove the container, rinse and dry.

rinsing milk circuit

in progress

milk circ. rinse cycle

Press to perform the rinse cycle.

THIS PROCEDURE MUST BE PERFORMED FOR ALL MILK BEVERAGES!

AFTER USE, ALWAYS REMOVE THE MILK CONTAINER AND PUT IT IN THE REFRIGERATOR IF IT

CONTAINS REMAINING MILK.

THE CONTAINER MAY BE LEFT IN THE MACHINE ONLY IF IT HAS BEEN WASHED WITH

DRINKING WATER AND IT DOES NOT CONTAIN MILK (SEE PAGE 39-40).

After performing the rinse cycle, the machine reminds the user to remove the container with the remaining milk through the message “remove milk”.

REMOVE THE MILK CONTAINER ONLY WHEN THE MACHINE IS ON.

remove milk

espresso coffee 08:33

BEVERAGE DISPENSING

1 2 3

ESPRESSO MACCHIATO

CAPPUCCINO

When “milk circuit rinsing” ﬂ ashes, rinse the milk circuits as described for the latte macchiato (see page 13, step

6).

strong aroma

espresso coffee 08:33

Press the button.

strong aroma

espresso macchiato 08:33

Select espresso macchiato by navigating the click wheel with your ﬁ nger.

Select the aroma by pressing the

button one or more times.

strong aroma

espresso macchiato 08:33

strong aroma

espresso macchiato 08:33

If you wish, press the button. Once the desired milk quantity has been reached, press the button again.

Press the

button once or

twice to start brewing.

add milk?

espresso macchiato

strong aroma

espresso coffee 08:33

Press the button.

strong aroma

cappuccino 08:33

Select cappuccino by navigating the click wheel with your ﬁ nger.

Select the aroma by pressing the

button one or more times.

strong aroma

cappuccino 08:33

Fill the milk container

WARNING! DO NOT OPEN THE SERVICE DOOR DURING THE BREWING, DISPENSING, WASHING OR RINSE CYCLE.

1 2 3

1 2

When “milk circuit rinsing” ﬂ ashes, rinse the milk circuits as described for the latte macchiato (see page 13, step

6).

brewing in progress

cappuccino

If you wish, press the button. Once the desired milk quantity has been reached, press the

button again.

Press the

button once or

twice to start brewing.

add milk?

cappuccino

HOT MILK

Repeat the operation to brew another cup of milk. When “rinsing milk circuit” ﬂ ashes, rinse the milk circuits as described for the latte macchiato (see page 13, step 6).

strong aroma

espresso coffee 08:33

Press the button.

hot milk 08:33

Select hot milk and press the button.

add milk?

hot milk

If you wish, press the button. Once the desired milk quantity has been reached, press the

button again.

Fill the milk container

HOT WATER

DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER AND SCALDING IS POSSIBLE. THE HOT WATER SPOUT MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS.

The machine brews the preset water quantity. Press the

button after brewing, to exit the “hot water” function.

hot water 08:33

Press the button.

brewing in progress

hot water

Press to start brewing.

BEVERAGE DISPENSING

WARNING! DO NOT OPEN THE SERVICE DOOR DURING THE BREWING, DISPENSING, WASHING OR RINSE CYCLE.

select the quantity of coffee to be ground (opti-dose), or select pre-ground coffee, and/or set:

- coffee temperature

- coffee prebrewing

navigate the click wheel with your

ﬁ nger to select:

- the quantity of coffee to be brewed;

- the quantity of milk to be dispensed;

- the coffee temperature;

- the coffee prebrewing.

restore factory settings.

select coffee or milk to change the quantity per cup.

save the new settings.

1. MANUAL PROGRAMMING

Each beverage can be programmed according to your individual taste.

The following page describes how to program a beverage containing milk and coffee; the programmable settings for each beverage may differ according to the type of beverage.

For all beverages you can quickly program the quantity of coffee and/or milk dispensed in the cups whenever the brew button is pressed. Select the type of beverage you want to program, then press and hold the

button until the display

shows (for example):

self-instruction active

espresso coffee

The machine dispenses coffee or milk. When the desired amount is reached, press the

button again.

The display will show:

(Only beverages with coffee and milk): for beverages with coffee and milk, you need to save the desired quantity of both milk and coffee by pressing the

button. This adjustment must be performed during the

relevant dispensing phase in the normal beverage dispensing process.

The dispensed quantity of coffee and/or milk remains stored and replaces any previous settings.

new quantity saved

espresso coffee

2. PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU

To adjust the settings for preparing beverages: press the button and select “beverage settings” by navigating the click wheel with your ﬁ nger.

In this phase you can:

exit the programming

mode.

beverage settings

BEVERAGE PROGRAMMING

1 2

4 5 6

7 8 9

10 11

Check that the water tank and coffee bean hopper are full; place the cup under the dispensing head.

Press the button.

Press the

button one or more times to adjust the aroma or select the use of pre-ground coffee. Press the

button to save.

Select the beverage to be programmed. Press the button to conﬁ rm.

Select “beverage settings”. Press the

button to conﬁ rm.

Change the coffee quantity by navigating the click wheel with your ﬁ nger; conﬁ rm with

. Press

to change the setting from

coffee to milk.

Change the milk quantity by navigating the click wheel with your ﬁ nger; conﬁ rm with

Press the

button for more than two seconds to access the other settings to be programmed.

Change the temperature value (high, medium, low) by navigating the click wheel with your ﬁ nger. Press the

button to save.

Press the button to select the prebrewing setting.

Change the prebrew value (normal, strong, off) by navigating the click wheel with your ﬁ nger. Press the

button to save. Press

the

button to exit.

Prebrewing: the coffee is slightly dampened before brewing to bring out the full aroma of the coffee which acquires an excellent taste.

strong aroma

espresso coffee 08:33

beverage settings

latte macchiato

strong aroma

latte macchiato

coffee:¸¿¸¿

latte macchiato

milk :¸¿¸¿

latte macchiato

temperature: high

latte macchiato

temperature: high

latte macchiato

prebrewing: normal

latte macchiato

prebrewing: normal

latte macchiato

beverage settings

BEVERAGE PROGRAMMING

Some of the machine›s functions can be programmed according to your individual preferences.

strong aroma

espresso coffee 08:33

Press the button to:

- conﬁ rm the selection;

- save the new settings.

1 Press the

button.

2 Navigate the click wheel with your ﬁ nger to:

- select the functions

- change the function settings.

beverage settings

Beverage settings (see page 17).

machine settings

special functions

Machine settings (see page 20).

Special functions (see page 35).

To exit the programming mode:

exit exit

PROGRAMMING THE MACHINE

1 2 3

LANGUAGE

MACHINE SETTINGS

To change the machine operation settings, press the key and select “machine settings”. Navigate the click wheel with your ﬁ nger to:

machine settings

language

machine settings

water filter

machine settings

water hardness

machine settings

rinse cycle

machine settings

cup warming plate

machine settings

acoustic alerts

machine settings

maintenance

machine settings

clock settings

machine settings stand-by setting

machine settings

maintenance

change the display language.

activate/deactivate the message to replace the water ﬁ lter.

change the water hardness setting.

set the circuit rinse cycle.

activate/deactivate the cup warmer.

set/activate the acoustic alarms.

clean the machine's internal circuits.

set the clock.

set the standby and the timers.

To exit any level of “machine settings” without saving the changes made, press the

button. For example:

machine settings machine settings

language

deutsch sprache

Select the desired language. After this, the machine displays all the messages in the language selected.

> machine settings > language . To change the language of the display.

PROGRAMMING THE MACHINE

1 2 3

1 2

CUP WARMING SURFACE

machine settings machine settings

cup warming plate

Select by navigating the click wheel with your ﬁ nger. It is possible to set:

- always on

- always off.

> machine settings > cup warming plate.

To activate/deactivate the cup warming surface located on the top of the machine. The cup warming surface is always off when the machine is in stand-by mode. A warm cup allows you to fully savor the coffee and taste its full aroma.

WATER FILTER

machine settings machine settings

water filter

Select by navigating the click wheel with your ﬁ nger. It is possible to set:

- on

- off

> machine settings > water filter.

When activated, this function informs the user when the water ﬁ lter needs to be replaced. This function must:

• be activated when the water ﬁ lter is in use;

• be deactivated when the water ﬁ lter is not in use.

water filter

water filter activation

water filter

initialization

The ﬁ lter control can be activated or deactivated from this menu.

A newly installed ﬁ lter can be initialized from this menu.

Press the

button to save.

Press the

button to save.

1 2 3

3 4 5

1234

Intenza Aroma System

Machine water hardness setting

Check the water hardness level obtained from the test.

The measurement can be used to set the Intenza Aroma System correctly (see page 7). Matching parameters are described on the upper part.

Immerse the water hardness test strip (included in the accessories) for one second in water.

The test strip can be used only for one measurement.

RINSE CYCLE

machine settings machine settings

rinse cycle

Note: This rinse cycle is performed every time the machine is turned on after the warming phase.

> machine settings > rinse cycle.

To clean the internal circuits in order to guarantee that the beverages are dispensed only with fresh water. This function is activated by default by the manufacturer.

Select by navigating the click wheel with your ﬁ nger. It is possible to set:

- yes

- no

WATER HARDNESS MENU - INTENZA AROMA SYSTEM

> machine settings > water hardness.

To adjust your machine and the Intenza water ﬁ lter to the level of hardness of the water you use, so that the machine will request descaling at the right moment.

The water hardness in the Intenza water ﬁ lter is expressed on a scale from A to C. The water hardness in the machine is expressed on a scale from 1 to 4.

machine settings machine settings

water hardness

- 3 + water hardness

Set and store the water hardness according to the value on the test strip.

Press the

button to save.

PROGRAMMING THE MACHINE

1 2 3

ACOUSTIC ALARM

machine settings machine settings

acoustic alerts

> machine settings > acoustic alerts

To enable/disable the acoustic alarms of the machine.

acoustic alerts

key tone

Select by navigating the click wheel with your ﬁ nger. You may set:

- key tone: to activate/deactivate a tone each time a button is pressed.

- milk quality warning: to activate/deactivate a tone when the milk container has been in the machine for too long.

- confirmation tone: to activate/deactivate a tone to conﬁ rm that a command (beverage saved, etc.) has been performed.

- milk circ. rinsing tone: to activate/deactivate a tone when the machine requires milk circuit cleaning.

- milk circ. rinse warning: to activate/deactivate a tone when the milk circuits have to be rinsed.

Press the

button to save.

1 2 3

MAINTENANCE MENU

machine settings

maintenance

milk circ. rinse cycle

> machine settings > maintenance.

To clean all the machine’s internal circuits used for making coffee and milk. Navigate the click wheel with your ﬁ nger to:

maintenance

milk circ. rinse cycle

maintenance

milk cleaning cycle

rinse the milk circuits after making the beverages.

thoroughly clean the milk circuits. This must be performed after a ﬁ xed time has elapsed from the ﬁ rst dispensing.

maintenance

coffee cleaning cycle

maintenance

descaling cycle

clean the brew group.

Perform the descaling cycle.

Milk circuit rinse cycle

> machine settings > maintenance > milk circ. rinse cycle

WARNING! DO NOT OPEN THE SERVICE DOOR DURING THE BREWING, DISPENSING, WASHING OR RINSE CYCLE.

To rinse the machine’s internal circuits used for preparing milk. This short cycle must be performed after 20 minutes from the last dispensing of a beverage with milk. If it is not performed, the machine comes to a halt and does not allow the dispensing of milk beverages. Note: Before performing this function make sure that:

1. a large enough container is positioned under the spout;

2. the milk container has been correctly inserted in the machine;

3. the water tank contains a sufﬁ cient quantity of water.

yes

milk circ. rinse cycle

in progress

milk circ. rinse cycle

Remove the container, rinse and dry.

Wait for the cycle to complete.

AFTER USE, ALWAYS REMOVE

THE MILK CONTAINER AND PUT IT

IN THE REFRIGERATOR.

The container may be left in the machine only if it has been washed with drinking water and it does not contain milk; see page 39.

PROGRAMMING THE MACHINE

1 2 3

4 65

machine settings

maintenance

coffee cleaning cycle

Coffee cleaning cycle

> machine settings > maintenance > coffee cleaning cycle

yes

coffee cleaning cycle

insert cleaning tablet

coffee cleaning cycle

Insert the tablet as shown above. Press

to start.

To clean the machine’s internal circuit used for brewing coffee.

To wash the brew group, simply clean with water as shown on page 41. This wash completes maintenance of the brew group. Packages of Saeco detergent tablets may be purchased directly from Saeco or an authorized service center.

It is advisable to perform this wash cycle after 500 coffee brewing cycles, or monthly.

Note: Before performing this function make sure that:

1. a large enough container is positioned under the spout;

2. the appropriate tablet for cleaning the brew group has been inserted into the pre-ground bypass doser;

3. the water tank contains a sufﬁ cient quantity of water

THE WASH CYCLE CANNOT BE INTERRUPTED. A PERSON MUST BE PRESENT DURING THE OPERATION.

in progress

coffee cleaning cycle

Wait for the cycle to complete.

Exiting programming mode. (see page 19)

done

coffee cleaning cycle

When the cleaning cycle has ﬁ nished, press

to conﬁ rm.

THE MAINTENANCE AND CLEANING OF THE BREW GROUP IS DESCRIBED ON PAGE 41.

1 2 3

machine settings

maintenance

milk cleaning cycle

Milk cleaning cycle

> machine settings > maintenance > milk cleaning cycle

yes

milk cleaning cycle

WARNING! DO NOT OPEN THE SERVICE DOOR DURING THE BREWING, DISPENSING, WASHING OR RINSE CYCLE.

To clean the machine’s internal circuits used for preparing milk.

This cycle is proposed after 14 days from the ﬁ rst dispensing of a milk-based beverage. After 14 days, the “milk circuit washing” message starts ﬂ ashing (see page 13).

Perform the wash cycle as indicated in this section. If the milk circuit washing cycle is not performed, dispensing milk-based products will be possible for only 7 more days.

After 21 days (the machine warns the user 3 days before the deadline is reached with the message “milk circuit washing -3”), the “milk circuit washing” message stops ﬂ ashing and appears any time the button to select a milk-based beverage is pressed.

At this point, the milk circuit washing cycle must be performed, because the dispensing of milk-based beverages is disabled. (The machine still enables dispensing hot water and coffee).

When the message “milk circuit washing” appears on the display, press the button

and follow the

instructions on page 26, step 4. The screen will appear as shown in step 9.

Note: Before performing this function make sure that:

1. a large enough container is at hand;

2. the milk container has been adequately cleaned of all milk residue;

3. the water tank contains a sufﬁ cient quantity of water.

THE WASH CYCLE CANNOT BE INTERRUPTED. A PERSON MUST BE PRESENT DURING THE OPERATION. USE THE PROVIDED MILK CLEANING DETERGENT.

Select and press

Detergent residue or water may remain in the container during the wash and rinse cycles. In this case, empty the container and rinse out any residue before ﬁ lling it again.

PROGRAMMING THE MACHINE

Fill the milk container with fresh water up to the «max» level.

Insert the contents of the detergent packet into the container.

Open the compartment and insert the container with the detergent.

Close the compartment. Press

to start.

Position an adequately sized container under the dispensing head.

Open the compartment and remove the milk container.

The wash cycle starts automatically. Wait for the wash cycle to ﬁ nish.

When the wash cycle has ﬁ nished the following appears… The machine signals the cycle is complete with an acoustic tone.

Remove the milk container.

add cleaner into

milk cleaning cycle

in progress

milk cleaning cycle

rinse

milk cleaning cycle

5 6

+ 70 hidden pages