NEFF T2144, T2144SOWO, T2124W0EU, T2124S1, T2124S0 User Manual
...
en
de
fr
it
es
nl
pt
tr
hu
el
ru Руководство по монтажу
лоуцмистжц, тоьецдржн пцддон еиэоаоптжао
5
5
480
a |
b |
c
a |
b |
c |
|
X4 |
|
d
e
Ø max. |
12,4 |
10 |
en
All installation, regulation and adaptation to other types of gas must be carried out by an authorised installation technician, respecting all applicable regulations, standards and the country's electrical and gas supply companies' specifications.
It is recommended that you call our Technical Assistance Service for adaptation to other types of gas. Before you begin, turn off the appliance's electricity and gas supply.
(see
table I).
If no oven is installed under an electrical or mixed (gas and electric) hob, place a separator of non-flammable material e.g. plywood or metal at a distance of 10 mm. from the bottom of the hob to prevent access to the lower part of the hob.
If no oven is installed under a gas hob, it is suggested to place a separator of nonflammable material e.g. plywood or metal at a distance of 10 mm. from the bottom of the hob to prevent access to the lower part of the hob.
In the event that a drawer is located beneath the appliance, please make sure that the drawer contains no heat-sensitive or easily combustible objects, such as spray cans or shoe polish. Use a heat-resistant utility drawer only.
If the cooking hob is to be installed above an oven, check that the oven is fitted with power ventilation, and check the dimensions according to the assembly manual.
2- The chipboard used to make the worktops tends to swell quite quickly when it comes into contact with moisture. Thus we recommend treating the cut edges with a special glue, to protect them from steam or any condensation
that might drip down beneath the cooker unit's work surface.
Depending on the model, the clips and the watertight seal (lower edge of the cooking hob) may already be fitted; if this is the case, do not remove them under any circumstance.
The seal ensures that the entire work surface will be watertight, and prevents water seepage.
If this item has not been fitted in the factory, remove the pan supports and the gas burner covers and diffusers from your cooking hob, and turn it upside down. Now fit the adhesive seal supplied with the appliance onto the lower edge of the cooking hob, depending on the model Fig. 3a/3b/3c.Remove the clips from the attached accessories bag and screw them into the lower points designed for this purpose, depending on the model Fig. 4d.,or place them in the holes provided for this purpose according to the clip model Fig. 4a or Fig. 4b.
At the same time, press down on the hob edges to ensure that the cooking hob is supported all the way round Fig. 5.
If your cooking hob model comes with the clip type which corresponds to Fig. 4d., once the hob is fitted you should turn the clip and tighten the screw as shown in Fig. 4e.
3- For disassembly, unscrew the clip and proceed in the reverse manner.
If your clip is type Fig. 4a you should push from below upwards.
If your clip is type Fig. 4b you should use a screwdriver to lever it upwards Fig. 4c.
(20,955 mm)
(L min. 1m - max. 3m).
All installation, regulation and adaptation to other types of gas must be carried out by an authorised installation technician, respecting all applicable regulations, standards and the country's electrical and gas supply companies' specifications.
It is recommended that you call our Technical Assistance Service for adaptation to other types of gas.
(see table II).
It has a flexible rubber seal. Simply apply pressure with the tip of the screwdriver to release the thread toward the tap´s adjusting screw. Fig. 9.
(Fig. 10):
Loading...