JLG 1932RS/6RS, 3248RS/10RS Operation And Safety Manual

ANSI

Operation and Safety Manual

Original Instructions - Keep this manual with the machine at all times.

Model(s)
1932RS/6RS
3248RS/10RS

3121272

June 29, 2018 - Rev F

WARNING

Operating, servicing and maintaining this vehicle or equipment
can expose you to chemicals including engine exhaust, carbon
monoxide, phthalates, and lead, which are known to the State of
California to cause cancer and birth defects or other
reproductive harm. To minimize exposure, avoid breathing
exhaust, do not idle the engine except as necessary, service your
vehicle or equipment in a well-ventilated area and wear gloves
or wash your hands frequently when servicing. For more
information go to www.P65Warnings.ca.gov.

SECTION - FOREWORD

FOREWORD

This manual is a very important tool! Keep it with the machine at all times.

The purpose of this manual is to provide owners, users, operators, lessors, and lessees with the precautions and operating proce­dures essential for the safe and proper machine operation for its intended purpose.

Due to continuous product improvements, JLG Industries, Inc. reserves the right to make specification changes without prior noti­fication. Contact JLG Industries, Inc. for updated information.

3121272 – JLG Lift – 1

SECTION - SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS

SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS

This is the Safety Alert Symbol. It is used to alert you to the potential personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.

INDICATES AN IMMINENTLY HAZARDOUS SITUATION. IF NOT AVOIDED, WILL
RESULT IN SERIOUS INJURY OR DEATH. THIS DECAL WILL HAVE A RED BACK­GROUND.

INDICATES A POTENTIALITY HAZARDOUS SITUATION. IF NOT AVOIDED, MAY
RESULT IN MINOR OR MODERATE INJURY. IT MAY ALSO ALERT AGAINST
UNSAFE PRACTICES. THIS DECAL WILL HAVE A YELLOW BACKGROUND.

NOTICE

INDICATES A POTENTIALITY HAZARDOUS SITUATION. IF NOT AVOIDED,
COULD RESULT IN SERIOUS INJURY OR DEATH. THIS DECAL WILL HAVE AN
ORANGE BACKGROUND.

2 – JLG Lift – 3121272

INDICATES INFORMATION OR A COMPANY POLICY THAT RELATES DIRECTLY
OR INDIRECTLY TO THE SAFETY OF PERSONNEL OR PROTECTION OF PROP­ERTY.

SECTION - SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS

THIS PRODUCT MUST COMPLY WITH ALL SAFETY RELATED BULLETINS. CON­TACT JLG INDUSTRIES, INC. OR THE LOCAL AUTHORIZED JLG REPRESENTA­TIVE FOR INFORMATION REGARDING SAFETY RELATED BULLETINS WHICH
MAY HAVE BEEN ISSUED FOR THIS PRODUCT.

NOTICE

JLG INDUSTRIES, INC. SENDS SAFETY RELATED BULLETINS TO THE OWNER OF
RECORD OF THIS MACHINE. CONTACT JLG INDUSTRIES, INC. TO ENSURE THAT
THE CURRENT OWNER RECORDS ARE UPDATED AND ACCURATE.

NOTICE

JLG INDUSTRIES, INC. MUST BE NOTIFIED IMMEDIATELY IN ALL INSTANCES
WHERE JLG PRODUCTS HAVE BEEN INVOLVED IN AN ACCIDENT INVOLVING
BODILY INJURY OR DEATH OF PERSONNEL OR WHEN SUBSTANTIAL DAMAGE
HAS OCCURRED TO PERSONAL PROPERTY OR THE JLG PRODUCT.

For:

• Accident Reporting

• Product Safety Publica-

tions

• Current Owner Updates

• Questions Regarding

Product Safety

• Standards and Regulations
Compliance Information

• Questions Regarding Special
Product Applications

• Questions Regarding Prod­uct Modifications

Contact:

Product Safety and Reliability Department
JLG Industries, Inc.
13224 Fountainhead Plaza
Hagerstown, MD 21742
USA

or Your Local JLG Office
(See addresses on manual rear cover)

In USA:

Toll Free: 877-JLG-SAFE (877-554-7233)

Outside USA:

Phone: [phone]
E-mail: [e-mail]

3121272 – JLG Lift – 3

SECTION - REVISION LOG

Original Issue A - January 10, 2012

Revised B - January 4, 2013

Revised C - April 8, 2013

Revised D - January 5, 2015

Revised E - May 26, 2016

Revised F - June 29, 2018 - Revised Covers, Prop 65

REVISION LOG

4 – JLG Lift – 3121272

TABLE OF CONTENTS

SECTION - PARAGRAPH, SUBJECT PAGE SECTION - PARAGRAPH, SUBJECT PAGE

FOREWORD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A

SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS . . . . . B

Contact: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C

In USA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C

Outside USA:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C

REVISION LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D

SECTION - 1 - SAFETY PRECAUTIONS

1.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.2 PRE-OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Operator Training and Knowledge. . . . . . . . . . . . . . . . . . . . . .1-2

Workplace Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Machine Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

1.3 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Trip and Fall Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Electrocution Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

Tipping Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

Crushing and Collision Hazards. . . . . . . . . . . . . . . . . . . . . . . . .1-9

1.4 TOWING, LIFTING, AND HAULING. . . . . . . . . . . . . . . . . . . . . . . 1-11

1.5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Maintenance Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Battery Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

SECTION - 2 - USER RESPONSIBILITIES, MACHINE PREPARATION
AND INSPECTION

2.1 PERSONNEL TRAINING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Operator Training. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Training Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Operator Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

2.2 PREPARATION, INSPECTION, AND MAINTENANCE . . . . . . . . .2-2

2.3 PRE-START INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

2.4 DAILY WALK-AROUND INSPECTION . . . . . . . . . . . . . . . . . . . . . .2-6

2.5 FUNCTION CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

SECTION - 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

3.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

3.2 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

3.3 OPERATING CHARACTERISTICS/LIMITATIONS . . . . . . . . . . . . .3-2

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

Placards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

3.4 PLATFORM LOADING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

3.5 MACHINE CONTROL LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . .3-3

3.6 GROUND CONTROL STATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

Ground Emergency Stop Switch . . . . . . . . . . . . . . . . . . . . . . . .3-6

Key Selector Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6

Platform Lift/Lower Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6

3121221 – JLG Lift – i

TABLE OF CONTENTS

SECTION - PARAGRAPH, SUBJECT PAGE SECTION - PARAGRAPH, SUBJECT PAGE

MDI-Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6

Overload Indicator (If Equipped) . . . . . . . . . . . . . . . . . . . . . . .3-7

3.7 PLATFORM CONTROL STATION. . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

Platform Emergency Stop Switch. . . . . . . . . . . . . . . . . . . . . .3-10

Lift/Drive Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

Forward/Reverse/Lift/Lower Direction Decal. . . . . . . . . . .3-10

Drive/Lift/Steer Joystick Control . . . . . . . . . . . . . . . . . . . . . . .3-11

Steering And Traveling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Traveling Forward and Reverse. . . . . . . . . . . . . . . . . . . . . . . .3-12

Raising And Lowering Platform. . . . . . . . . . . . . . . . . . . . . . . .3-14

Arm Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

Overload Indicator (If Equipped) . . . . . . . . . . . . . . . . . . . . . .3-14

Tilt Indicator Warning Light and Alarm . . . . . . . . . . . . . . . .3-15

Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

Low Battery Charge and System Fault Indicator . . . . . . . .3-15

Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

3.8 PLATFORM EXTENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16

3.9 PLATFORM RAILS - FOLD-DOWN PROCEDURE - (3248RS/10RS

AND 6RS-CE ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

3.10 BATTERY CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

Battery Charger Fault (LED Flash) . . . . . . . . . . . . . . . . . . . . . .3-21

3.11 DC TO AC INVERTER OPERATION (OPTION) . . . . . . . . . . . . . .3-22

3.12 PARKING AND STOWING MACHINE. . . . . . . . . . . . . . . . . . . . . .3-23

3.13 SCISSOR ARM - SAFETY PROP . . . . . . . . . . . . . . . . . . . . . . . . . . .3-24

3.14 MACHINE LIFTING AND TIE DOWN . . . . . . . . . . . . . . . . . . . . . .3-26

Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-26

Tie Down. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-26

3.15 TOWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-29

Electric Brake Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-29

Mechanical Brake Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-30

SECTION - 4 - EMERGENCY PROCEDURES

4.1 GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2 EMERGENCY OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Operator Unable to Control Machine . . . . . . . . . . . . . . . . . . .4-1

Platform Caught Overhead. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Righting of Tipped Machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.3 PLATFORM MANUAL DESCENT. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.4 INCIDENT NOTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

SECTION - 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

5.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Other Publications Available:. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.2 OPERATING SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Platform Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Machine Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4

Tires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

ii – JLG Lift – 3121221

TABLE OF CONTENTS

SECTION - PARAGRAPH, SUBJECT PAGE SECTION - PARAGRAPH, SUBJECT PAGE

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

5.3 CRITICAL STABILITY WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

5.4 LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Lubrication Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

5.5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8

Hydraulic Oil Check Procedure . . . . . . . . . . . . . . . . . . . . . . . . .5-8

5.6 BATTERY MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9

Battery Maintenance and Safety Practices. . . . . . . . . . . . . . .5-9

Battery Quick-Disconnect - (If Equipped) . . . . . . . . . . . . . . . .5-9

5.7 TIRES AND WHEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

Tire Wear and Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

Wheel and Tire Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

Wheel Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

5.8 SUPPLEMENTAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . 5-12

5.9 DECAL INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

5.10 DIAGNOSTIC TROUBLE CODES (DTC). . . . . . . . . . . . . . . . . . . . 5-17

5.11 DTC CHECK TABLE INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17

5.12 DIAGNOSTIC TROUBLE CODES (DTC)

CHECK TABLES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

0-0 Help Comments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

2-1 Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19

2-2 Platform Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19

2-3 Ground Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

2-5 Function Prevented . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

3-1 Line Contactor Open Circuit . . . . . . . . . . . . . . . . . . . . . . 5-22

3-2 Line Contactor Short Circuit . . . . . . . . . . . . . . . . . . . . . . 5-22

3-3 Ground Output Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22

4-2 Thermal Limit (SOA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25

4-4 Battery Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25

6-6 Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26

7-7 Electric Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26

8-2 LSS - Load Sensing System. . . . . . . . . . . . . . . . . . . . . . . . 5-27

8-4 Elevation Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28

9-9 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29

SECTION - 6 - INSPECTION AND REPAIR LOG

LIST OF FIGURES

2-1. Daily Walk-Around Inspection - All Machines . . . . . . . . . .2-7

2-2. Machine Limit Switch Location . . . . . . . . . . . . . . . . . . . . . . .2-9

3-1. 1932RS/6RS - Location of Machine Controls.. . . . . . . . . . . 3-3

3-2. 3248RS/10RS - Location of Machine Controls. . . . . . . . . .3-4

3-3. Ground Control Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

3-4. MDI Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7

3-5. Location of Manual Descent Control . . . . . . . . . . . . . . . . . .3-8

3-6. Platform Control Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

3121221 – JLG Lift – iii

TABLE OF CONTENTS

SECTION - PARAGRAPH, SUBJECT PAGE SECTION - PARAGRAPH, SUBJECT PAGE

3-7. Platform Control Components. . . . . . . . . . . . . . . . . . . . . . .3-11

3-8. Grade and Sideslope Definition . . . . . . . . . . . . . . . . . . . . . .3-13

3-9. Platform Deck Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16

3-10. Platform Rails - Fold Down Sequence -

3248RS/10RS Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

3-11. Platform Rails - Fold Down Sequence -

6RS (CE Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19

3-12. Charger Decal LED Indicators . . . . . . . . . . . . . . . . . . . . . . . .3-20

3-13. Location of AC Inverter ON/OFF - Toggle Switch. . . . . .3-22

3-14. Securing Control Station to Platform. . . . . . . . . . . . . . . . .3-23

3-15. 1932RS/6RS - Scissor Arm - Safety Prop . . . . . . . . . . . . . .3-25

3-16. 3248RS/10RS - Scissor Arm - Safety Prop . . . . . . . . . . . . .3-25

3-17. Fork Lift Pockets - Location . . . . . . . . . . . . . . . . . . . . . . . . . .3-26

3-18. Lifting Using Spreader Bar and

Lift Lug Locations - All Machines . . . . . . . . . . . . . . . . . . . . .3-27

3-19. Tie Down and Lift Lug Locations - All Machines. . . . . . .3-28

3-20. Electric Brake Release - Location - All Machines. . . . . . .3-29

3-21. Brake - Manual Disengage. . . . . . . . . . . . . . . . . . . . . . . . . . .3-30

4-1. Location of Manual Descent Control . . . . . . . . . . . . . . . . . .4-2

5-1. Hydraulic Oil Check Procedure - All Machines . . . . . . . . . 5-8

5-2. Battery Fluid Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9

5-3. Wheel Lug Nut Tightening Sequence . . . . . . . . . . . . . . . .5-11

5-4. Machine Decal Installation - All Machines . . . . . . . . . . . .5-12

LIST OF TABLES

1-1 Minimum Approach Distances (M.A.D.) . . . . . . . . . . . . . . .1-6

1-2 Beaufort Scale (For Reference Only) . . . . . . . . . . . . . . . . . . .1-8

2-1 Inspection and Maintenance Table. . . . . . . . . . . . . . . . . . . .2-3

2-2 High Drive Cutout Height. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

2-3 Tilt Activation Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

3-1 Battery Charger Fault (LED Flash) . . . . . . . . . . . . . . . . . . . .3-21

5-1 Operating Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

5-2 Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3

5-3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4

5-4 Tire Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

5-5 Battery Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

5-6 Electrical System Specifications . . . . . . . . . . . . . . . . . . . . . . .5-5

5-7 Critical Stability Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

5-8 Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

5-9 Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

5-10 Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

5-11 Hydraulic Oil Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

5-12 Wheel Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11

5-13 Machine Decal Installation Chart. . . . . . . . . . . . . . . . . . . . .5-13

6-1 Inspection and Repair Log . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

iv – JLG Lift – 3121221

SECTION 1. SAFETY PRECAUTIONS

SECTION 1 - SAFETY PRECAUTIONS

1.1 GENERAL

This section outlines the necessary precautions for proper
and safe machine usage and maintenance. In order to pro­mote proper machine usage, it is mandatory that a daily
routine is established based on the content of this manual.
A maintenance program, using the information provided
in this manual and the Service and Maintenance Manual,
must also be established by a qualified person and must
be followed to ensure that the machine is safe to operate.

The owner/user/operator/lessor/lessee of the machine
must not accept operating responsibility until this manual
has been read, training is accomplished, and operation of
the machine has been completed under the supervision of
an experienced and qualified operator.

These sections contain the responsibilities of the owner,
user, operator, lessor, and lessee concerning safety, train­ing, inspection, maintenance, application, and operation.If
there are any questions with regard to safety, training,
inspection, maintenance, application, and operation,
please contact JLG Industries, Inc. (“JLG”).

FAILURE TO COMPLY WITH THE SAFETY PRECAUTIONS LISTED IN THIS MAN­UAL COULD RESULT IN MACHINE DAMAGE, PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH.

3121272 – JLG Lift – 1-1

SECTION 1 - SAFETY PRECAUTIONS

1.2 PRE-OPERATION

Operator Training and Knowledge

• The Operation and Safety Manual must be read and under­stood in its entirety before operating the machine. For clari­fication, questions, or additional information regarding any
portions of this manual, contact JLG Industries, Inc.

• An operator must not accept operating responsibilities
until adequate training has been given by competent and
authorized persons.

• Allow only those authorized and qualified personnel to
operate the machine who have demonstrated that they
understand the safe and proper operation and mainte­nance of the unit.

• Read, understand, and obey all DANGERS, WARNINGS, CAU­TIONS, and operating instructions on the machine and in
this manual.

• Ensure that the machine is to be used in a manner which is
within the scope of its intended application as determined
by JLG.

• All operating personnel must be familiar with the emer­gency controls and emergency operation of the machine as
specified in this manual.

• Read, understand, and obey all applicable employer, local,
and governmental regulations as they pertain to your utili­zation and application of the machine.

Workplace Inspection

• Precautions to avoid all hazards in the work area must be
taken by the user before and during operation of the
machine.

• Do not operate or raise the platform from a position on
trucks, trailers, railway cars, floating vessels, scaffolds or
other equipment unless the application is approved in writ­ing by JLG.

• Before operation, check work area for overhead hazards
such as electric lines, bridge cranes, and other potential
overhead obstructions.

• Check floor surfaces for holes, bumps, drop-offs, obstruc­tions, debris, concealed holes, and other potential hazards.

1-2 – JLG Lift – 3121272

SECTION 1 - SAFETY PRECAUTIONS

• Check the work area for hazardous locations. Do not oper­ate the machine in hazardous environments unless
approved for that purpose by JLG.

• Ensure that the ground conditions are adequate to support
the maximum tire load indicated on the tire load decals
located on the chassis adjacent to each wheel.

• This machine can be operated in nominal ambient temper­atures of 0
mize operation outside of this temperature range.

o

F to 104o F (-20o C to 40o C). Consult JLG to opti-

Machine Inspection

• Do not operate this machine until the inspections and func­tional checks have been performed as specified in Section 2
of this manual.

• Do not operate this machine until it has been serviced and
maintained according to the maintenance and inspection
requirements as specified in the machine’s Service and
Maintenance Manual.

• Ensure all safety devices are operating properly. Modifica­tion of these devices is a safety violation.

MODIFICATION OR ALTERATION OF AN AERIAL WORK PLATFORM SHALL BE
MADE ONLY WITH PRIOR WRITTEN PERMISSION FROM THE MANUFACTURER.

• Do not operate any machine on which the safety or instruc­tion placards or decals are missing or illegible.

• Check the machine for modifications to original compo­nents. Ensure that any modifications have been approved
by JLG.

• Avoid accumulation of debris on platform deck. Keep mud,
oil, grease, and other slippery substances from footwear
and platform deck.

1.3 OPERATION

General

• Machine operation requires your full attention. Bring the
machine to a full stop before using any device, i.e. cell
phones, two-way radios, etc. that will distract your attention
from safely operating the machine.

• Do not use the machine for any purpose other than posi­tioning personnel, their tools, and equipment.

• Before operation, the user must be familiar with the
machine capabilities and operating characteristics of all
functions.

• Never operate a malfunctioning machine. If a malfunction
occurs, shut down the machine. Remove the unit from ser­vice and notify the proper authorities.

3121272 – JLG Lift – 1-3

SECTION 1 - SAFETY PRECAUTIONS

• Do not remove, modify, or disable any safety devices.

• Never slam a control switch or lever through neutral to an

opposite direction. Always return switch to neutral and stop
before moving the switch to the next function. Operate
controls with slow and even pressure.

• Do not allow personnel to tamper with or operate the
machine from the ground with personnel in the platform,
except in an emergency.

• Do not carry materials directly on platform railing unless
approved by JLG.

• When two or more persons are in the platform, the operator
shall be responsible for all machine operations.

• Always ensure that power tools are properly stowed and
never left hanging by their cord from the platform work
area.

• Do not assist a stuck or disabled machine by pushing or
pulling except by pulling at the chassis tie-down lugs.

• Fully lower platform and shut off all power before leaving
machine.

• Remove all rings, watches, and jewelry when operating
machine. Do not wear loose fitting clothing or long hair
unrestrained which may become caught or entangled in
equipment.

• Persons under the influence of drugs or alcohol or who are
subject to seizures, dizziness or loss of physical control must
not operate this machine.

• The following information is provided in accordance with
the requirements of the European Machinery Directive
2006/42/EC and is only applicable to CE machines.
For electric powered machines, the equivalent continuous
A-Weighted sound pressure level at the work platform is
less than 70dB(A).
For combustion engine powered machines, guaranteed
Sound Power Level (LWA) per European Directive 2000/ 14/
EC (Noise Emission in the Environment by Equipment for
Use Outdoors) based on test methods in accordance with
Annex III, Part B, Method 1 and 0 of the directive, is 109 dB.
The vibration total value to which the hand-arm system is
subjected does not exceed 2,5 m/s2. The highest root mean
square value of weighted acceleration to which the whole
body is subjected does not exceed 0,5 m/s2.

1-4 – JLG Lift – 3121272

SECTION 1 - SAFETY PRECAUTIONS

Trip and Fall Hazards

• Prior to operation, ensure all gates and rails are fastened
and secured in their proper position.

• JLG Industries, Inc. recommends that all persons in the plat­form wear a full body harness with a lanyard attached to an
authorized lanyard anchorage point while operating this
machine. For further information regarding fall protection
requirements on JLG products, contact JLG Industries, Inc.

• Identify the designated lanyard anchorage point(s) at the
platform and securely attach the lanyard. Attach only one
(1) lanyard per lanyard anchorage point.

• Enter and exit only through gate area. Use extreme caution
when entering or leaving platform. Ensure that the platform
assembly is fully lowered. Face the machine when entering
or leaving the platform. Always maintain “three point con­tact” with the machine, using two hands and one foot or
two feet and one hand at all times during entry and exit.

.

• Keep both feet firmly positioned on the platform floor at all
times. Never position ladders, boxes, steps, planks, or simi­lar items on unit to provide additional reach for any pur­pose.

• Never use the scissor arm assembly to gain access to or
leave the platform.

• Keep oil, mud, and slippery substances cleaned from foot­wear and the platform floor.

3121272 – JLG Lift – 1-5

SECTION 1 - SAFETY PRECAUTIONS

Electrocution Hazards

• This machine is not insulated and does not provide protec­tion from contact or proximity to electrical current.

• Maintain distance from electrical lines, apparatus, or any
energized (exposed or insulated) parts according to the
Minimum Approach Distance (MAD) as shown in Table 1-1.

• Allow for machine movement and electrical line swaying.

• Maintain a clearance of at least 10 ft. (3m) between any part

of the machine and its occupants, their tools, and their
equipment from any electrical line or apparatus carrying up
to 50,000 volts. One foot additional clearance is required for
every additional 30,000 volts or less.

1-6 – JLG Lift – 3121272

• The minimum approach distance may be reduced if insulat-

ing barriers are installed to prevent contact, and the barri­ers are rated for the voltage of the line being guarded.
These barriers shall not be part of (or attached to) the
machine. The minimum approach distance shall be reduced
to a distance within the designed working dimensions of
the insulating barrier. This determination shall be made by
a qualified person in accordance with the employer, local,
or governmental requirements for work practices near
energized equipment.

DO NOT MANEUVER MACHINE OR PERSONNEL INSIDE PROHIBITED ZONE (MAD).
ASSUME ALL ELECTRICAL PARTS AND WIRING ARE ENERGIZED UNLESS KNOWN OTH­ERWISE.

Table 1-1. Minimum Approach Distances (M.A.D.)

VOLTAGE RANGE

(Phase to Phase)

MINIMUM APPROACH DISTANCE

in Feet (Meters)

0 to 50 KV 10 (3)

Over 50KV to 200 KV 15 (5)

Over 200 KV to 350 KV 20 (6)

Over 350 KV to 500 KV 25 (8)

Over 500 KV to 750 KV 35 (11)

Over 750 KV to 1000 KV 45 (14)

NOTE: This requirement shall apply except where employer, local or govern-

mental regulations are more stringent.

SECTION 1 - SAFETY PRECAUTIONS

Tipping Hazards

• Ensure that the ground conditions are adequate to support
the maximum tire load indicated on the tire load decals
located on the chassis adjacent to each wheel. Do not travel
on unsupported surfaces.

• The user must be familiar with the driving surface before
driving. Do not exceed the allowable sideslope and grade
while driving.

• Do not elevate platform or drive with platform elevated
while on or near a sloping, uneven, or soft surface. Ensure
machine is positioned on a firm, level and smooth surface
before elevating platform or driving with the platform in
the elevated position.

• Before driving on floors, bridges, trucks, and other surfaces,
check allowable capacity of the surfaces.

• Never exceed the maximum work load as specified on the
platform. Keep all loads within the confines of the platform,
unless authorized by JLG.

• Keep the chassis of the machine a minimum of 2 ft. (0.6m)
from holes, bumps, drop-offs, obstructions, debris, con­cealed holes, and other potential hazards at the ground
level.

• Do not operate the machine when wind conditions exceed
specifications shown in Section 5, Table 5-2 or as shown on
the capacity placard on the platform billboard.

3121272 – JLG Lift – 1-7

SECTION 1 - SAFETY PRECAUTIONS

DO NOT OPERATE THE MACHINE WHEN WIND CONDITIONS EXCEED SPECIFICATIONS SHOWN IN SECTION 5, TABLE 5-2 OR AS SHOWN ON THE CAPACITY PLACARD ON THE PLAT­FORM BILLBOARD.

Table 1-2. Beaufort Scale (For Reference Only)

BEAUFORT

NUMBER

WIND SPEED

DESCRIPTION LAND CONDITIONS

mph m/s

0 0 0-0.2 Calm Calm. Smoke rises vertically.

1 1-3 0.3-1.5 Light air Wind motion visible in smoke.

2 4-7 1.6-3.3 Light breeze Wind felt on exposed skin. Leaves rustle.

3 8-12 3.4-5.4 Gentle breeze Leaves and smaller twigs in constant motion.

4 13-18 5.5-7.9 Moderate breeze Dust and loose paper raised. Small branches begin to move.

5 19-24 8.0-10.7 Fresh breeze Smaller trees sway.

6 25-31 10.8-13.8 Strong breeze Large branches in motion. Flags waving near horizontal. Umbrella

use becomes difficult.

7 32-38 13.9-17.1 Near Gale/Moderate Gale Whole trees in motion. Effort needed to walk against the wind.

8 39-46 17.2-20.7 Fresh Gale Twigs broken from trees. Cars veer on road.

9 47-54 20.8-24.4 Strong Gale Light structure damage.

1-8 – JLG Lift – 3121272

SECTION 1 - SAFETY PRECAUTIONS

• Never attempt to use the machine as a crane. Do not tie-off
machine to any adjacent structure. Never attach wire, cable,
or any similar items to platform.

• Do not cover the platform sides or carry large surface-area
items in the platform when operating outdoors. The addi­tion of such items increases the exposed wind area of the
machine.

• Do not increase the platform size with unauthorized deck
extensions or attachments.

• If the scissor arm assembly or platform is caught so that one
or more wheels are off the ground, all persons must be
removed before attempting to free the machine. Use
cranes, forklift trucks, or other appropriate equipment to
stabilize machine and remove personnel.

Crushing and Collision Hazards

• Approved head gear must be worn by all operating and
ground personnel.

• Keep hands and limbs out of the scissor arm assembly dur­ing operation and when elevated without safety prop
engaged.

• Watch for obstructions around machine and overhead
when driving. Check clearances above, on sides, and bot­tom of platform when lifting or lowering platform.

3121272 – JLG Lift – 1-9

SECTION 1 - SAFETY PRECAUTIONS

• During operation, keep all body parts inside platform rail­ing.

• Always post a lookout when driving in areas where vision is
obstructed.

• Keep non-operating personnel at least 6 ft. (1.8m) away
from machine during all operations.

• Under all travel conditions, the operator must limit travel
speed according to conditions of ground surface, conges­tion, visibility, slope, location of personnel, and other fac­tors.

• Be aware of stopping distances in all drive speeds. When
driving in high speed, switch to low speed before stopping.
Travel grades in low speed only.

• Do not use high speed drive in restricted or close quarters
or when driving in reverse.

• Exercise extreme caution at all times to prevent obstacles
from striking or interfering with operating controls and per­sons in the platform.

• Ensure that operators of other overhead and floor level
machines are aware of the aerial work platform’s presence.
Disconnect power to overhead cranes. Barricade floor area
if necessary.

• Do not operate over ground personnel. Warn personnel not
to work, stand, or walk under a raised platform. Position
barricades on floor as necessary.

1-10 – JLG Lift – 3121272

SECTION 1 - SAFETY PRECAUTIONS

1.4 TOWING, LIFTING, AND HAULING

• Never allow personnel in platform while towing, lifting, or
hauling.

• This machine should not be towed, except in the event of
emergency, malfunction, power failure, or loading/unload­ing. Refer to emergency towing procedures.

• Ensure platform is fully retracted and completely empty of
tools prior to towing, lifting or hauling.

• When lifting machine with a forklift, position forks only at
designated areas of the machine. Lift with a forklift of ade­quate capacity.

• Refer to Section 3 for lifting information.

1.5 MAINTENANCE

This sub-section contains general safety precautions which
must be observed during maintenance of this machine. Addi­tional precautions to be observed during machine mainte­nance are inserted at the appropriate points in this manual
and in the Service and Maintenance Manual. It is of utmost
importance that maintenance personnel pay strict attention
to these precautions to avoid possible injury to personnel or
damage to the machine or property. A maintenance program

must be established by a qualified person and must be fol­lowed to ensure that the machine is safe.

Maintenance Hazards

• Shut off power to all controls and ensure that all moving
parts are secured from inadvertent motion prior to per­forming any adjustments or repairs.

• Never work under an elevated platform until it has been
fully lowered to the full down position, if possible, or other­wise supported and restrained from movement with appro­priate safety props, blocking, or overhead supports.

• DO NOT attempt to repair or tighten any hydraulic hoses or
fittings while the machine is powered on or when the
hydraulic system is under pressure.

• Always relieve hydraulic pressure
from all hydraulic circuits before
loosening or removing hydraulic
components.

• DO NOT use your hand to check for
leaks. Use a piece of cardboard or
paper to search for leaks. Wear
gloves to help protect hands from
spraying fluid.

• Ensure replacement parts or components are identical or
equivalent to original parts or components.

3121272 – JLG Lift – 1-11

SECTION 1 - SAFETY PRECAUTIONS

• Never attempt to move heavy parts without the aid of a
mechanical device. Do not allow heavy objects to rest in an
unstable position. Ensure adequate support is provided
when raising components of the machine.

• Use only approved non-flammable cleaning solvents.

• Do not replace items critical to stability, such as batteries or

solid tires, with items of different weight or specification.
Do not modify unit in any way to affect stability.

• Reference the Service and Maintenance Manual for the
weights of critical stability items.

MODIFICATION OR ALTERATION OF AN AERIAL WORK PLATFORM SHALL BE
MADE ONLY WITH PRIOR WRITTEN PERMISSION FROM THE MANUFACTURER.

Battery Hazards

• Always disconnect batteries when servicing electrical com­ponents or when performing welding on the machine.

• Do not allow smoking, open flame, or sparks near battery
during charging or servicing.

• Do not contact tools or other metal objects across the bat­tery terminals.

• Always wear hand, eye, and face protection when servicing
batteries. Ensure that battery acid does not come in contact
with skin or clothing.

BATTERY FLUID IS HIGHLY CORROSIVE. AVOID CONTACT WITH SKIN AND
CLOTHING AT ALL TIMES. IMMEDIATELY RINSE ANY CONTACTED AREA WITH
CLEAN WATER AND SEEK MEDICAL ATTENTION.

• Charge batteries only in a well ventilated area.

• Avoid overfilling the battery fluid level. Add distilled water

to batteries only after the batteries are fully charged.

1-12 – JLG Lift – 3121272

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

SECTION 2. USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

2.1 PERSONNEL TRAINING

The aerial platform is a personnel handling device; so it is neces­sary that it be operated and maintained only by trained person­nel.

Operator Training

Operator training must cover:

• Use and limitations of the controls in the platform and at the
ground, emergency controls and safety features.

• Control labels, instructions, and warnings on the machine.

• Rules of the employer and government regulations.

• Use of approved fall protection equipment.

• Enough knowledge of the mechanical operation of the machine to

recognize a malfunction or potential malfunction.

• The safest means to operate the machine where overhead obstruc­tions, other moving equipment, and obstacles, depressions, holes,
and drop-offs exist.

• Means to avoid the hazards of unprotected electrical conductors.

• Specific job requirements or machine application.

• Reading and understanding the Operation and Safety Manual.

3121272 – JLG Lift – 2-1

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

Training Supervision

Training must be done under the supervision of a qualified per­son in an open area free of obstructions until the trainee has
developed the ability to safely control and operate the machine.

Operator Responsibility

The operator must be instructed that he/she has the responsi­bility and authority to shut down the machine in case of a mal­function or other unsafe condition of either the machine or the
job site.

NOTE: The Manufacturer or Distributor will provide qualified

people for training assistance with the first unit(s) deliv­ered and from that time forward as requested by the user
or his/her personnel.

2.2 PREPARATION, INSPECTION, AND MAINTENANCE

Table 2-1 explains the periodic machine inspections and main­tenance recommended by JLG Industries, Inc. Consult local reg­ulations for further requirements for aerial work platforms. The
frequency of inspections and maintenance must be increased
as necessary when the machine is used in a harsh or hostile
environment, if the machine is used with increased frequency,
or if the machine is used in a severe manner.

2-2 – JLG Lift – 3121272

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

NOTICE

Table 2-1. Inspection and Maintenance Table

TYPE FREQUENCY

Pre-Start Inspec tion Before using each day; or

whenever there’s an Operator change.

Pre-Delivery Inspection

(see note below)

Frequent Inspection In service for 3 months or 150 hours, whichever comes

Annual Machine
Inspection

(see note below)

Preventative Maintenance At intervals as specified in the Ser vice and Mainte-

NOTE: Inspection forms are available from JLG. Use the Service and Maintenance Manual to perform inspections.

JLG INDUSTRIES, INC. RECOGNIZES A FACTORY-TRAINED SERVICE TECHNICIAN AS A PERSON WHO HAS SUCCESSFULLY COMPLETED THE JLG SERVICE TRAINING SCHOOL FOR
THE SPECIFIC JLG PRODUCT MODEL.

Before each sale, lease, or rental delivery. Owner, Dealer, or User Qualified JLG

first; or Out of service for a period of more than 3
months; or Purchased used.

Annually, no later than 13 months from the date of
prior inspection.

nance Manual.

PRIMARY

RESPONSIBILITY

User or Operator User or Operator Operation and Safety Manual

Owner, Dealer, or User Qualified JLG

Owner, Dealer, or User Factory Trained Ser-

Owner, Dealer, or User Qualified JLG

SERVICE

QUALIFICATION

Mechanic

Mechanic

vice Technician
(Recommended)

Mechanic

REFERENCE

Service and Maintenance Manual and
applicable JLG inspection form

Service and Maintenance Manual and
applicable JLG inspection form

Service and Maintenance Manual and
applicable JLG inspection form

Service and Maintenance Manual

3121272 – JLG Lift – 2-3

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

2.3 PRE-START INSPECTION

The Pre-Start Inspection should include each of the following:

1. Cleanliness – Check all surfaces for leakage (oil or bat­tery fluid) or foreign objects. Report this to the proper
maintenance personnel.

2. Structure - Inspect the machine structure for dents,
damage, weld or parent metal cracks or other discrep­ancies. Report this to the proper maintenance person­nel.

.

Parent Metal Crack Weld Crack

3. Decals and Placards – Check all for cleanliness and
legibility. Ensure none of the decals and placards are
missing. Ensure all illegible decals and placards are
cleaned or replaced. (See Section 5.8, DECAL INSTAL­LATION)

4. Operation and Safety Manuals - Ensure that a copy
of the Operation and Safety Manual, AEM Safety Man­ual (ANSI markets only), and ANSI Manual of Responsi­bilities (ANSI markets only) is enclosed in the weather
resistant storage container.

5. “Walk-Around” Inspection – Refer to Figure 2-1. on
page 2-7.

6. Battery – Charge as required.

7. Hydraulic Oil Level - Check the hydraulic oil level in

the pump reservoir, add as required. (See Section 5.5)

8. Accessories/Attachments - Reference the Operation
and Safety Manual of each attachment or accessory
installed upon the machine for specific inspection,
operation, and maintenance instructions.

9. Function Check – Once the “Walk-Around” Inspection
is complete, perform a functional check of all systems
in an area free of overhead and ground level obstruc­tions. Refer to Section 3 for more specific instructions
on the operation of each function.

2-4 – JLG Lift – 3121272

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

1

1

1

10. Platform Gate - Keep gate and surrounding area
clean and unobstructed. Check that gate closes prop­erly and is not bent or damaged. During operation
keep gate closed.

Chain Gate

11. Lanyard Anchorage Points - JLG Industries, Inc. rec­ommends personnel in the platform wear a full body
harness with a lanyard attached to an authorized lan­yard anchorage point (1).

Self-Closing Swing Gate

3121272 – JLG Lift – 2-5

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

NOTICE

2.4 DAILY WALK-AROUND INSPECTION

Begin the “Walk-Around Inspection” at item 1, see Figure 2-1. on
page 2-7. Continue checking each item in sequence for the con­ditions listed in the following checklist.

TO AVOID POSSIBLE INJURY, BE SURE MACHINE POWER IS “OFF”. DO NOT
OPERATE UNTIL ALL MALFUNCTIONS HAVE BEEN CORRECTED.

DO NOT OVERLOOK VISUAL INSPECTION OF CHASSIS UNDERSIDE. CHECKING
THIS AREA MAY RESULT IN DISCOVERY OF CONDITIONS WHICH COULD CAUSE
EXTENSIVE MACHINE DAMAGE.

INSPECTION NOTE: On all components, make sure there are no
loose or missing parts, that they are securely fastened, and that
no visible damage, leaks or excessive wear exists in addition to
any other criteria mentioned.

1. Frame/Chassis - See Inspection Note. Ensure that pas-
sive pothole components on frame are in place,
undamaged, not bent or worn.

2. Ground Controls - Placard secure and legible, control
switches return to neutral position, emergency stop
switch functions properly. Control markings legible.

3. Hydraulic Pump/Motor, Control Valve Installation - No
unsupported wires or hoses; no damaged or broken
wires - See Inspection Note.

4. Front Wheels - Steer linkage, and Steer Cylinder - See
Inspection Note.

5. Battery Compartment - See Inspection Note.

6. Rear Wheels, Tires and Drive Motors - Properly

secured, no missing lug nuts. Refer to Section 5.7,
TIRES AND WHEELS. Inspect wheels for damage and
corrosion - See Inspection Note.

7. Manual Descent Control - See Inspection Note.

8. Beacon (if equipped) - See Inspection Note.

9. Scissor Arms, Pivot Pins and Sliding Wear Pads, Lift Cyl-

inder - See Inspection Note.

10. Platform/Handrail/Gate Installation - Deck extension
slides in and out and locks in place properly. Gate
closes properly. All fold-down rail pins in place and
secure (3248RS/10RS and 6RS CE ONLY) - See Inspec-

tion Note.

11. Platform Control Console - Ensure that the control
console is firmly secured in the proper location. Plac­ards secure and legible, control lever and switches
return to neutral, and emergency stop switch function
properly, required manuals in storage box.

2-6 – JLG Lift – 3121272

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

1

2

3

5

7

6

8

9

10

11

4

8

1

1

1

3121272 – JLG Lift – 2-7

Figure 2-1. Daily Walk-Around Inspection (Side Covers Removed) - All Machines

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

2.5 FUNCTION CHECK

Perform the Function Check as follows:

1. From the Ground Control Panel with no load in the
platform:

a. Ensure that the key selector switch and the plat-

form lift switch operates properly.

b. Ensure that all machine functions are disabled

when the Emergency Stop Button is depressed.

c. With platform raised a few feet (1m), ensure that

the manual descent control (located at the right
rear of the machine), lowers the platform properly.

2. From the Platform Control Console:

a. Ensure that the control console is firmly secured

in the proper location.

b. Ensure that all guards protecting switches are in

place.

c. Operate all functions, drive/lift mode select

switch, and horn button.

d. Operate all platform joystick functions to ensure

proper operation of drive, lift, steer, and enable
trigger switch operation.

e. With the platform elevated on a smooth, firm,

level surface with no overhead obstructions, drive
the machine to check if the high drive cutout

speed-limit is engaged at the height indicated in
Table 2-2. Ensure drive speed is reduced from a
top speed to a slower speed. Limit switch loca­tions shown in Figure 2-2. on page 2-9.

Table 2-2. High Drive Cutout Height

MODEL

1932RS/6RS 68.9 in. (1.75m) 2.5 mph (4 kph) to

3248RS/10RS 88.5 in. (2.25 m)

f. Ensure that all machine functions are disabled

3. With the platform in the transport (stowed) position.
a. Drive the machine on a grade, not to exceed the

b. Check the tilt indicator light/alarm to ensure

NOTE: When the tilt indicator warning is activated the following

functions are affected; drive and lift up functions are dis-

HIGH DRIVE SPEED

CUTOUT HEIGHT

when the platform Emergency Stop Button is
depressed.

rated gradeability, and stop to ensure the drive
motor brakes hold.

proper operation. The light/alarm should be acti­vated, and lift up disabled when tilted at or
beyond the values in Table 2-3.

DRIVE SPEED REDUCTION

0.3 mph (0.5 kph)

2-8 – JLG Lift – 3121272

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

1

1

abled, platform must be fully lowered (stowed) to drive
out of tilt condition.

Table 2-3. Tilt Activation Setting

MODEL

TILT SETTING

(front to back)

TILT SETTING
(side to side)

1932RS/6RS - ALL 3° 1.5°

3248RS/10RS - ANSI/CSA/JPN 3° 2°

3248RS/10RS - CE 3° 1.5°

1932RS/6RS

3248RS/10RS

Figure 2-2. Machine Limit Switch Location

1. Elevation Switch

3121272 – JLG Lift – 2-9

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION

NOTES:

2-10 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

NOTICE

SECTION 3. MACHINE CONTROLS, INDICATORS AND OPERATION

3.1 GENERAL

THE MANUFACTURER HAS NO DIRECT CONTROL OVER MACHINE APPLICA­TION AND OPERATION, THE USER AND OPERATOR ARE RESPONSIBLE FOR
CONFORMING WITH GOOD SAFETY PRACTICES.

This section provides the necessary information needed to
understand controls and their functions.

DO NOT RAISE PLATFORM EXCEPT ON A SMOOTH, FIRM AND LEVEL SURFACE
FREE OF OBSTRUCTIONS AND HOLES.

TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY CONTROL
LEVERS OR TOGGLE SWITCHES CONTROLLING PLATFORM MOVEMENT DO NOT
RETURN TO THE OFF OR NEUTRAL POSITION WHEN RELEASED.

IF THE PLATFORM DOES NOT STOP WHEN A CONTROL SWITCH OR LEVER IS
RELEASED, USE THE EMERGENCY STOP SWITCH TO STOP THE MACHINE.

3121272 – JLG Lift – 3-1

3.2 DESCRIPTION

This machine is a self-propelled aerial work platform on top of
an elevating scissor arm mechanism. The Lift’s intended pur­pose is to position personnel with their tools and supplies at
positions above ground level. The machine can be used to reach
work areas located above machinery or equipment positioned
at ground level.

This JLG Lift has a primary operator control station in the plat­form. From this control station, the operator can drive and steer
the machine in both forward and reverse directions, raise and
lower the platform.
The machine can be driven on a smooth, firm, and level surface
from an elevated platform position - Reference “Steering And
Traveling” on page 3-12. of this manual for specific require­ments.

The machine also has a ground control station which can over­ride the platform control station. Ground controls operate lift up
and down. Ground controls are to be used only in an emergency
to lower the platform to the ground should the operator in the
platform be unable to do so.

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

3.3 OPERATING CHARACTERISTICS AND LIMITATIONS

General

A thorough knowledge of the operating characteristics and lim­itations of the machine is always the first requirement for any
user, regardless of user’s experience with similar types of equip­ment.

Placards

Important points to remember during operation are provided at
the control stations by DANGER, WARNING, CAUTION, NOTICE,
and INSTRUCTION placards. This information is placed at various
locations for the express purpose of alerting personnel of
potential hazards constituted by the operating characteristics
and limitations of the machine. See foreword for definitions of
placard safety signal words.

3.4 PLATFORM LOADING

The platform maximum rated load capacity is shown on a plac­ard located on the platform billboard and ground control sta­tion and is based upon the machine positioned on a smooth,
firm, and level surface. Refer to Section 5, Table 5-2 on page 5-4,
for the maximum platform capacity.

The platform is entered through an entry gate at the rear of the
platform. Keep entry gate closed during machine operation.

NOTE: It is important to remember that the load should be

evenly distributed on the platform. The load should be
placed near the center of the platform when possible.

3-2 – JLG Lift – 3121272

3.5 MACHINE CONTROL LOCATIONS

1

2

3

3

4

5

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1. Ground Control Station

2. Platform Control Station

3. Platform Manual Descent Control

4. AC Plug - To Platform AC Receptacle Outlet Box

5. AC Plug - Battery Charger Input Plug

3121272 – JLG Lift – 3-3

Figure 3-1. 1932RS/6RS - Location of Machine Controls.

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

4

5

2

3

3

1. Ground Control Station

2. Platform Control Station

3. Platform Manual Descent Control

4. AC Plug - To Platform AC Receptacle Outlet Box

5. AC Plug - Battery Charger Input Plug

Figure 3-2. 3248RS/10RS - Location of Machine Controls.

3-4 – JLG Lift – 3121272

3.6 GROUND CONTROL STATION

1001132360A

1

2

3

4

5

1001146979A

DO NOT OPERATE FROM GROUND CONTROL STATION WITH PERSONNEL IN
THE PLATFORM EXCEPT IN AN EMERGENCY.

PERFORM AS MANY PRE-OPERATIONAL CHECKS AND INSPECTIONS FROM
THE GROUND CONTROL STATION AS POSSIBLE.

Ground Emergency Stop Switch - (Item 3 - Figure 3-3.)

Power is turned on by pulling the switch out, and is turned off
by depressing switch. A two-position, red, mushroom-shaped
emergency stop switch, when positioned to ON with the key
selector switch positioned to ground, furnishes operating
power to the ground control station key switch. In addition, the
switch can be used to turn off power to the function controls in
the event of an emergency.

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1. Platform Lift/Lower Switch

2. Key Selector Switch

Figure 3-3. Ground Control Station

4. MDI - Indicator

5. Overload Indicator (If Equipped)

3. Ground Emergency Stop Button

3121272 – JLG Lift – 3-5

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

2

3

Key Selector Switch - (Item 2 - Figure 3-3.)

The key selector switch on the
Ground Control Station functions to
direct electrical power to the desired
control station. With the switch
turned to the ground position (1),
power is supplied to the controls at
the ground control station. When the
switch is turned to the platform
position (2), power is supplied to the
controls at the platform control sta­tion. The switch should be set to the OFF position (3) when
parking the machine overnight.

Platform Lift/Lower Switch - (Item 1 - Figure 3-3.)

A three position, momentary contact lift control switch provides
raising and lowering of the platform from the Ground Control
Station.

When operating platform from the ground controls -

Toggle the lift/lower switch to up position and hold to raise plat­form, or down position and hold to lower an elevated platform.
Release to center position to stop all movement.

MDI-Indicator - (Item 4 - Figure 3-3.)

The MDI indicator or Multifunction Digital Indicator displays a
Battery Discharge Indicator (BDI), an LCD display which shows
the current hour-meter reading or Diagnostic Trouble Code(s)

(DTC) when a functional problem occurs with the machine, and
a system distress LED.

When a problem occurs (DTC Code displayed):

A wrench Icon (item 1) will display on the Diagnostic Trouble

Code LCD display (item 2). (See Figure 3-4.)

• A three to five digit DTC code will display on the Diagnostic
Trouble Code LCD display (item 2), below the wrench

icon.

• The system distress LED indicator (RED) (item 3) lights up
solid on the MDI when a DTC Code is displayed on the LCD
display.

NOTE: When more than one DTC exists, each DTC will be dis-

played on the LCD for 3 seconds before changing to the
next DTC. Once the last active DTC is displayed, the display
will recycle indefinitely until the DTC’s are corrected.
For DTC’s and descriptions, refer to Section 5.9.

Also located on the MDI are Battery Discharge Indicators
(BDI) (items 4 thru 7). (4) GREEN LEDs indicate the level of

charge (voltage) remaining in the batteries.

NOTE: When the battery voltage is low and will need a charge

soon, the LED (item 4) in the 0-25% range "red area" will
flash.

Under normal operating conditions the BDI’s and hour-meter
will be displayed. When a DTC exists (other than 00x

DTC’s) the

3-6 – JLG Lift – 3121272

BDI LEDs and hour-meter will not be displayed. Also when plat-

1

2

3

7

6

5

4

form is elevated and the machine is being driven the creep
mode (turtle) is displayed.

Overload Indicator (If Equipped) - (Item 5 - Figure 3-3.)

Overload Indicator - Indicates the platform has been over­loaded. An audible alarm will also signal when the platform is
overloaded.

NOTE: CE/Australia/Japan/ANSI Export: If the Overload Indi-

cator is illuminated, all platform controls are prevented,
unless the platform has been raised less than 9.84 ft. (3m)
then lift down only is permitted. Reduce the weight in the
platform to not exceed the rated workload indicated on
the capacity decal.

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Figure 3-4. MDI Indicator

1. HourMeter, Wrench, Creep Icon
Indicators

2. Hour-meter/DTC Code Display

3. System Fault LED Indicator (RED

LED)

4. 0-25% Charge Indicator
(RED AREA)

5. 50% Charge Indicator
(YELLOW AREA)

6. 75% Charge Indicator
(GREEN AREA)

7. 100% Charge Indicator
(GREEN AREA)

3121272 – JLG Lift – 3-7

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Platform Manual Descent Control

The platform manual descent control is used in the event of
total power failure to lower the platform using gravity. The man­ual descent control T-handle is located on the right rear of the
machine, just in front of the drive wheel.

The lowering procedure is as follows:

1. Locate the manual descent control T-handle.

(See Figure 3-5.)

KEEP HANDS AND ARMS OUT OF THE PATH OF THE SCISSOR ARMS AND PLAT­FORM WHILE LOWERING.

2. Grasp the T-handle and slowly pull out to lower the
scissor arms/platform, when the platform is lowered
to desired level, allow the T-handle to return to it’s
closed position.

1932RS/6RS

3248RS/10RS

Figure 3-5. Location of Manual Descent Control

(Right Rear of Machine)

3-8 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1001132362 B

1

3

4

8

9

10

2

5

1

2

6

7

11

3.7 PLATFORM CONTROL STATION

1. Steer Control Switch

2. Drive and Lift Joystick Control

3. Trigger Switch

4. Forward/Reverse/Lift/Lower Direction Decal

5. Alarm

6. Overload Indicator (If Equipped)

7. Machine Tilt Indicator

8. Emergency Stop Switch

9. Horn Button

10. Drive and Lift Select Switch

11. Low Battery Charge and

System Fault Indicator

Figure 3-6. Platform Control Station.

3121272 – JLG Lift – 3-9

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1001132362 B

Platform Emergency Stop Switch - (Item 8 - Figure 3-6.)

NOTE: Both the ground and platform emergency stop buttons

must be set to ON in order to operate the machine.

When power is directed to the platform from the ground control
station, the platform emergency stop switch is turned on by
pulling the switch out (on), and is turned off by pushing the
switch in (off). The two-position, red, mushroom-shaped emer­gency stop switch functions to provide power to the platform
control station and also to turn off power to machine functions
in the event of an emergency.

Lift/Drive Select - (Item 10 - Figure 3-6.)

NOTE: When selecting between the Lift and Drive functions the

joystick control must be returned to the neutral position
for approximately 1/2 second before the function change
is operable.

This toggle switch is used to select operation of either the drive
or lift function. After selecting a function, the joystick controller
must be moved in the proper direction in order to activate that
function. Only change the function selected, with the joystick in
the neutral position. Otherwise, the function selected will not
change until the joystick is returned to the neutral position.

Forward/Reverse/Lift/Lower Direction Decal - (Item 4 - Figure 3-6.)

This decal indicates the proper direction to
mount the platform control box, the black
arrow must point to the front of the machine.
The black/white arrow also indicates the
direction to move the joystick control per the
lift/drive selector switch decal for the lift and drive select func­tions.

3-10 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

2

3

1

Drive/Lift/Steer Joystick Control

Figure 3-7. Platform Control Components

1. Trigger Switch

2. Steer Switch

3. Joystick Controller

1. Trigger Switch - This switch is located on the front of
the joystick controller. The trigger switch acts as an
enable and must be depressed before operating the
drive, steer and lift functions. When released, the func­tion being operated will stop.

NOTE: Once the trigger switch is pressed, the operator has (5)

seconds to begin operating a function, after 5 seconds you
must release the trigger switch and press it again to oper­ate a joystick function.

The speed on all selected functions is proportionally con­trolled by the distance from the neutral (center) position
of the joystick controller.

NOTE: If the machine is equipped with a footswitch (Japanese

Specification Only), the footswitch must be depressed in
conjunction with the red trigger switch, located on the
controller. Power is removed from the platform controls
when the footswitch is released.

2. Steer Switch - The steer switch is a thumb operated
switch located at the top of the control handle.
Depressing the switch to the right will steer the
wheels to the right. Depressing the switch to the left
will steer the wheels to the left.

3. Joystick Controller - The control handle controls
three functions: drive, lift, and steer.

3121272 – JLG Lift – 3-11

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Steering And Traveling

DO NOT DRIVE WITH PLATFORM RAISED EXCEPT ON A SMOOTH, FIRM AND
LEVEL SURFACE FREE OF OBSTRUCTIONS AND HOLES.

TO AVOID LOSS OF TRAVEL CONTROL OR UPSET ON GRADES AND SIDESLOPES,
DO NOT DRIVE MACHINE ON GRADES OR SIDESLOPES EXCEEDING THOSE
SPECIFIED IN TABLE 5-1 ON PAGE 5-2.

BEFORE DRIVING, LOCATE THE DECALS WITH THE BLACK/WHITE ORIENTA­TION ARROWS ON THE CHASSIS AND THE PLATFORM CONTROLS. MOVE THE
JOYSTICK IN THE DIRECTION OF THE BLACK OR WHITE ARROW THAT
MATCHES THE COLOR OF THE ARROW ON THE CHASSIS FOR THE INTENDED
DIRECTION OF TRAVEL.

IF THE TILT INDICATOR WARNING LIGHT/ALARM IS ACTIVATED WHILE DRIV­ING WITH PLATFORM RAISED, LOWER PLATFORM COMPLETELY AND DRIVE
TO A FIRM LEVEL SURFACE.

1. Place key selector switch at the ground control station
to platform operation.

2. Position emergency stop switches, one at the platform
and one at the ground control station to the ON posi­tion.

Steering

(Item 2 - Figure 3-7.)

On the platform control station, position the
lift/drive select switch to the drive position.

To steer the machine, press the thumb oper­ated steer rocker-switch on the joystick han­dle to the right for steering right, or to the
left for steering left. When released, the switch will return to the
center-off position and the wheels will remain in the previously
selected position. To return the wheels to the center position,
the switch must be activated in the opposite direction until the
wheels are centered.

Traveling Forward and Reverse

(Item 1 and 3 - Figure 3-7.)

Position the platform lift/drive
select switch to drive/steer posi­tion. Squeeze the trigger switch
on front of the joystick, and
move the joystick forward to
drive forward or backward to
drive in reverse. The drive system is proportional, for additional
drive speed push the joystick further from the neutral position
in the direction of travel. Releasing the trigger switch or return­ing the joystick to center will stop machine movement.

3-12 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

HORIZONTAL (LEVEL)

GRADE

SIDESLOPE

Figure 3-8. Grade and Sideslope Definition

3121272 – JLG Lift – 3-13

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Raising And Lowering Platform

1. If the machine was shut down, place the key selector
switch to the desired position (platform or ground).

2. Position emergency stop switches, one at the platform
and one at the ground control station to the ON posi­tion.

3. Position the lift/drive
select switch to lift.

(Item 10 - Figure 3-6.)

4. Squeeze and hold the

trigger switch, and
move the joystick back
(platform up - white arrow direction) or move the joy­stick forward (platform down - black arrow direction)
and hold until desired elevation is reached. Releasing
the trigger switch or moving the joystick back to it’s
center position will stop the function being operated.

(Item 1 and 3 - Figure 3-7.)

NOTE: To ensure proper operation of the desired platform func-

tion, move the joystick in the direction of the black or
white arrow that matches the color of the arrow on the
chassis for the intended direction of travel.

Arm Guards (If equipped)

If the machine is equipped with electronic arm guards, the plat­form will stop lowering at a predetermined height, lowering can
continue after a three (3) second delay. Once the lowering func­tion is reengaged an audible alarm will sound and the machine
beacons will flash to warn ground personnel near the machine.
After a one and a half (1.5) second delay the platform will con­tinue lowering.

Overload Indicator (If Equipped) -

(Item 6 - Figure 3-6.)

Indicates the platform has been over­loaded. An audible alarm will also signal
when the platform is overloaded.

NOTE: If the Overload Indicator is illuminated;

ANSI Export: All functions will be prevented from the

platform and ground controls. Lower platform using the
machine manual descent control.
CE/Australia/Japan: All platform functions will be pre­vented. Fully lower the platform from the ground controls
or using the machine manual descent control. Reduce the
weight in the platform to not exceed the rated workload
indicated on the capacity decal.

NOTE: CE/Australia/Japan/ANSI Export: If the Overload Indi-

cator is illuminated, all platform controls are prevented,
unless the platform has been raised less than 9.84 ft. (3m)

3-14 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

then lift down only is permitted. Reduce the weight in the
platform to not exceed the rated workload indicated on
the capacity decal.

Tilt Indicator Warning Light and Alarm -

(Item 7 - Figure 3-6.)

A red warning light on the control panel illu­minates and an audible alarm sounds when
the chassis is at or beyond the tilt cutout set­tings.

IF THE TILT INDICATOR WARNING LIGHT/ALARM IS ACTIVATED WHEN PLAT­FORM IS RAISED LOWER PLATFORM AND DRIVE TO A SMOOTH FIRM LEVEL
SURFACE.

Horn - (Item 9 - Figure 3-6.)

This push-button switch, when pressed, per­mits the operator to warn job site personnel
when the machine is operating in the area.

Low Battery Charge and System Fault Indicator - (Item 11 - Figure 3-6.)

This indicator light comes on and stays lit
when the battery charge level is very low,

indicating the batteries will need recharging
soon.

When indicator light is flashing a system
fault has occurred, possibly stopping
machine operation. Check the MDI indicator on the Ground
Control Station to see if a (DTC) Diagnostic Trouble Code(s) is
displayed. An explanation of DTC codes is shown in Section 5.9.
If the code cannot be cleared by the operator, the machine will
require service by a qualified JLG mechanic.

Alarm - (Item 5 - Figure 3-6.)

This alarm mounted on the front of the platform control station
will sound for various machine conditions or warnings such as,
system ready chirp or if the machine tilt warning is activated.

3121272 – JLG Lift – 3-15

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

2

3.8 PLATFORM EXTENSION

(See Figure 3-9.)

This machine is equipped with an extension deck, giving the
operator better access to certain work areas. The deck extension
adds length to the front of the platform.

FOR MAXIMUM CAPACITY OF THE DECK EXTENSION SEE SECTION 5, TABLE 5­2 OR REFER TO THE CAPACITY PLACARD ON THE PLATFORM BILLBOARD.

DO NOT “LOWER” WITHOUT COMPLETELY RETRACTING THE PLATFORM
EXTENSION.

To exten d the de c k:

1. Pull up on the locking pin (1) on left side mid-rail near

the front of the machine. Rotate pin 90° to hold in up
position.

2. Grasp the top handrails (2) of the extendible deck
and push the extension out until it hits the stops.

3. Re-engage the locking pin (1) and move platform
extension in or out until the locking pin engages.

To retract the deck:

1. Pull up on the mid-rail locking pin (1) and turn the pin

90° to hold in up position.

2. Pull the extension deck all the way back into the main
deck using the top handrail (2).

3. Re-engage the mid-rail locking pin (1) back to the
locked position and engage the hole in the mid-rail.

Figure 3-9. Platform Deck Extension

3-16 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

3.9 PLATFORM RAILS - FOLD-DOWN PROCEDURE ­(3248RS/10RS and 6RS-CE Only)

(See Figure 3-10. and Figure 3-11.)

DO NOT RAISE PLATFORM WITH RAILS FOLDED DOWN. THE RAILS MUST BE
IN THE UPRIGHT POSITION AND PROPERLY PINNED WHEN RAISING THE
PLATFORM.

NOTE: The rails must only be folded down when the machine is in

the stowed (platform fully lowered) position.
The platform control box should be removed from mount
before the side rails are folded down.

The platform rails fold down from the mid rail only, except for
the rear gate rail.

NOTE: If equipped with the optional self-closing gate, the gate

must be held open while lowering the rear and side rails.

The platform rails fold down in the following sequence;

(See Figure 3-10. and Figure 3-11.)

• First - pull pins, fold down rear gate rail (1).

NOTE: Front deck extension top rail pins must be removed and

deck extension top side rails slid towards rear of machine
before lowering side rails. Place pins back in the extension
side top rails before folding main platform side rails down.

• Second - pull pins, fold down both side rails (2 & 3).

• Last - pull pins, fold down front platform extension rail
(4).

1. To fold down each of the rails, remove the bail pins for

that rail.

2. Taking a firm hold on the top rail, carefully lower until
the top rail is fully folded in the down position.

3. To raise the rails back to the upright position, unfold
the rails in the reverse sequence they were folded.
Firmly pull the rails back up into position and replace
the bail pins into the rails.

4. Retract the extension deck and set it’s lock pin.

AFTER THE RAILS HAVE BEEN FOLDED DOWN, USE EXTREME CAUTION WHEN
EXITING AND ENTERING THE PLATFORM. ENTER AND EXIT PLATFORM ONLY
AT THE GATE AREA AND LADDER PROVIDED.

IF OPERATING (DRIVING) MACHINE WITH PLATFORM CONTROL STATION
FROM GROUND, WITH RAILS FOLDED, KEEP AT LEAST 3 FT. (1 M) DISTANCE
FROM MACHINE.

3121272 – JLG Lift – 3-17

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

1

3

3

2

2

4

4

3-18 – JLG Lift – 3121272

Figure 3-10. Platform Rails - Fold Down Sequence - 3248RS/10RS Only

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

1

3

3

2b

2a

2

4

4

Figure 3-11. Platform Rails - Fold Down Sequence - 6RS (CE Only)

3121272 – JLG Lift – 3-19

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

GREEN (ON) ­Battery Fully Charged

AMBER (ON) ­Battery Charging

AMBER (FLASHING) ­Battery/System
Problem

RED (FLASHING) ­Charger Problem

GREEN

AMBER

RED

LEDS

3.10 BATTERY CHARGING

through the opening on the rear panel where the
charger AC cord is accessed.

NOTE: Be sure that machine is parked in a well ventilated area

before charging begins.

4. The batteries are fully charged when the green light
on the battery charger status panel is illuminated.

NOTE: If the charger is left plugged in, the charger will automati-

ONLY PLUG THE CHARGER INTO A PROPERLY INSTALLED AND GROUNDED
OUTLET. DO NOT USE GROUND ADAPTORS OR MODIFY PLUG. DO NOT TOUCH
NON-INSULATED PORTION OF OUTPUT CONNECTOR OR NON-INSULATED

cally restart a complete charge cycle if the batteries volt­age drops below a minimum voltage or 30 days has
elapsed.

BATTERY TERMINAL.
DO NOT OPERATE CHARGER IF THE AC SUPPLY CORD IS DAMAGED OR IF THE
CHARGER HAS RECEIVED A SHARP BLOW, BEEN DROPPED, OR OTHERWISE
DAMAGED IN ANY WAY.
ALWAYS DISCONNECT THE CHARGER AC SUPPLY BEFORE MAKING OR BREAK­ING THE (POS/NEG) CONNECTIONS TO THE BATTERY.
DO NOT OPEN OR DISASSEMBLE CHARGER.

1. The battery charger AC input plug is located in an
opening on the panel at the lower rear of the machine.

2. Connect the charger AC input plug to a grounded out­let using a 3 wire heavy duty extension cord. (See
Table 5-6, “Electrical System Specifications,” on page 5­6, for battery charger AC input specifications.)

3. When powered up the charger will go through a short
LED indicator self-test. The battery charger LED indica­tors on the charger (Figure 3-12.), will flash in sequence
for two seconds. These LED indicators can be viewed

3-20 – JLG Lift – 3121272

Figure 3-12. Charger Decal LED Indicators

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Battery Charger Fault (LED Flash)

If a fault has occurred during battery charging, the (AMBER or
RED) LED on the charger LED indicator (See Figure 3-12.) will
flash corresponding to the fault which occurred. Refer to Table
3-1 following for the charger LED flash codes and their meaning.

Table 3-1. Battery Charger Fault (LED Flash)

FLASHING LED FAULT REMEDY

AMBER Battery High Voltage

AMBER Batte ry Low Voltage

AMBER Failed Trickle to min V

RED Charger Internal Fault Signals a hardware fault of the charger and shall indicate flashing red LED.

Upon battery voltage >2.5V per cell @ startup, charger shall flash amber LED and not
allow charging - Battery or System problem.

Upon battery voltage <0.17V per cell @ startup, charger shall flash amber LED and
not allow charging - Battery or System problem.

Should battery fail to reach 1.75V per cell charge shall flash an amber LED until char­ger is power cycled - Battery or System problem.

If required, further general and troubleshooting information
about the battery charger can be found in the charger manufac­turers Owner’s Guide.

3121272 – JLG Lift – 3-21

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

NOTICE

INVERTER

ON

OFF

1001143010A

1

2

3.11 DC TO AC INVERTER OPERATION (OPTION)

The platform AC receptacle box extension cable plug,
also located at the rear of the machine can be plugged
into the inverter AC extension cable, or a device can
be plugged directly into the inverter AC cable at this
point.

NOTE: Turn off any device before connecting to inverter AC cir-

cuit. Connect devices one at a time to the AC receptacle
box. Do not connect to many high-surge devices at once.

IF INVERTER SWITCH IS LEFT ON AND EMERGENCY STOP BUTTON IS NOT
PUSHED IN, POWER WILL DRAIN FROM THE BATTERIES.

3. To turn off the AC current to the platform AC recepta­cle box, set the inverter toggle switch to the OFF posi-

Figure 3-13. Location of AC Inverter ON/OFF -

Toggle S w itch

NOTE: The inverter audible alarm may make a momentary chirp

tion.

when the inverter is turned OFF. This same alarm may also

1. Inverter ON/OFF Switch 2. Ground Control Panel

sound when the inverter is being connected to or discon­nected from the 24 volt battery bank.

1. The AC inverter ON/OFF toggle switch (1) is located
on the machines’ ground control panel (2).

2. When the toggle switch is set to the ON position this
will allow AC current from the inverter to flow to the
inverter AC extension cable plug located at the right

NOTE: Further General and Troubleshooting information about

the Inverter can be found in the Service Manual for this
machine.

rear of the machine.

3-22 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

NOTICE

1001132362 B

1

2

3.12 PARKING AND STOWING MACHINE

1. Drive the machine to a well-protected and well-venti­lated area.

2. Ensure the platform is fully lowered.

WHEN THE MACHINE IS SHUT DOWN FOR OVERNIGHT PARKING OR BATTERY
CHARGING, THE EMERGENCY STOP AND POWER SELECT SWITCHES MUST BE
POSITIONED TO OFF TO PREVENT DRAINING THE BATTERIES.

3. At the ground control station, turn the platform ­ground selector key switch to OFF and remove the key
to disable the machine and prevent unauthorized use.

NOTE: For added protection, the platform control station can be

secured to it’s mounting plate see Figure 3-14.

4. At the ground control station, depress emergency
stop switch to the off position.

5. If necessary, cover the platform control box, instruc­tion placards, caution and warning decals so that they
will be protected from hostile environment.

6. Chock at least two wheels when parking the machine
for an extended period of time.

To prevent unauthorized removal, the platform control sta­tion can be secured to it’s mount by replacing the lock pin
located on it’s mounting tab with a keyed or combination
lock.

Figure 3-14. Securing Control Station to Platform

3121272 – JLG Lift – 3-23

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

3.13 SCISSOR ARM - SAFETY PROP

NEVER WORK UNDER AN ELEVATED PLATFORM UNTIL IT HAS BEEN
RESTRAINED FROM MOVEMENT WITH THE SAFETY PROP, BLOCKING OR
OVERHEAD SLING.

The safety prop is located at the rear of the machine on the rod
end of the lift cylinder located between the scissor arms.

To engage the safety prop:

1. From the Ground Control Station, raise the platform

far enough to allow the safety prop to be engaged on
the lift cylinder rod.

2. Pull out/up on the stop handle to release the safety
prop locking pin.

3. Rotate the prop assembly until it rests on the lift cylin­der rod.

4. Lower the platform until the safety prop rests against
the head of the lift cylinder, stopping all downward
movement of the platform/scissor arm assembly.

To release the safety prop:

1. Raise the platform enough to release the safety prop

off the head of the cylinder.

2. Pull the prop handle downward to restore the prop
back to its released position.

3. Ensure the locking pin to hold the safety prop in the
released position is engaged.

3-24 – JLG Lift – 3121272

Prop Engaged

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Prop Engaged

Prop Released and Locked

Figure 3-15. 1932RS/6RS - Scissor Arm - Safety Prop

3121272 – JLG Lift – 3-25

Figure 3-16. 3248RS/10RS - Scissor Arm - Safety Prop

Prop Released and Locked

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

1

3.14 MACHINE LIFTING AND TIE DOWN

Lifting

The machine may be lifted using a fork lift truck. Lift only from
the rear of the machine and only with the platform in the
stowed position. Adjust the width of the forklift truck, lifting
tines (1) to properly fit the machine, see Figure 3-17.

The machine can also be lifted using a spreader bar and four
equal length straps or chains capable of supporting the full
gross weight of the machine, see Figure 3-18. Lift only using the
lifting lugs provided at the four corners of the machine. (See Sec-
tion 5 for machine gross weight).

Tie Down

When transporting the machine, the platform must be fully low­ered in the stowed position with the machine securely tied
down to the truck or trailer deck. There are two tie-down/lift
lugs located at the front and rear of the machine. (See Figure 3-

19.)

1932RS/6RS

3-26 – JLG Lift – 3121272

Figure 3-17. Fork Lift Pockets - Location

3248RS/10RS

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

2

1

Figure 3-18. Lifting Using Spreader Bar and Lift Lug Locations - All Machines

1. Four (4) equal length chains or lifting straps. 2. Spreader Bar Assembly.

3121272 – JLG Lift – 3-27

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

Figure 3-19. Tie Down and Lift Lug Locations - All Machines

3-28 – JLG Lift – 3121272

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

2

1

3.15 TOWING

It is not recommended that this machine be towed, except in
the event of an emergency such as a machine malfunction or a
total machine power failure.

Electric Brake Release

(See Figure 3-20.)

NOTE: Electrical release of the brakes requires enough battery

power to hold the brakes in released mode until destina­tion is reached.

1. Chock wheels or secure machine with tow vehicle.

2. Turn power on in ground mode on the ground con­trol station (1).

3. The brake release switch (2) is located inside the

hydraulic components side cover, remove cover to
access the switch.

4. Depress the brake release switch once to release
brakes.

5. When finished towing depress brake release switch
again or turn power off at the ground control station
to re-engage the brakes.

NOTE: Any action which causes a loss of power from the brakes

such as, depressing the ground control emergency stop
switch, or switching the key switch to OFF or PLATFORM
MODE will re-engage the brakes.

3121272 – JLG Lift – 3-29

Figure 3-20. Electric Brake Release - Location - All

Machines

SECTION 3 - MACHINE CONTROLS, INDICATORS AND OPERATION

1

2

4

3

Mechanical Brake Release

(See Figure 3-21.)

CHOCK WHEELS OR SECURE MACHINE WITH TOW VEHICLE.

1. At the ground control station turn power off by press­ing the Emergency Stop switch in.

2. Remove the two cover bolts (1), and the cover (2),
from the back of drive motor unit.

3. Insert the cover bolts (1) into the two disengage
holes in the brake housing (4), see Figure 3-21.,

Brake - Manual Disengage.

4. Tighten down the cover bolts (3) in the disengage
holes and the brake on that drive motor will disen­gage.

5. Repeat this procedure on opposite wheel drive. With
both drive motor brakes now disengaged the machine
can be moved manually.

6. After towing is complete, chock wheels and remove
cover bolts from disengage holes.

7. Reinstall cover (2) - before installation check the
cover gasket (3) for damage, replace if necessary.

AFTER THE MACHINE IS TOWED THE COVER BOLTS (1) MUST BE REMOVED
FROM THE BRAKE DISENGAGE HOLES (4). THE BRAKES CANNOT BE ENGAGED
IF THE DISENGAGE BOLTS ARE LEFT IN THE DISENGAGE HOLES. THIS WILL
CAUSE THE MACHINE TO ROLL WHEN PARKED ON AN INCLINE.

3-30 – JLG Lift – 3121272

Figure 3-21. Brake - Manual Disengage.

SECTION 4 - EMERGENCY PROCEDURES

SECTION 4. EMERGENCY PROCEDURES

4.1 GENERAL INFORMATION

This section explains the steps to be taken in case of an emer­gency situation during operation.

4.2 EMERGENCY OPERATION

Operator Unable to Control Machine

IF THE PLATFORM OPERATOR IS UNABLE TO OPERATE OR CON­TROL THE MACHINE:

1. Other personnel should operate the machine from
ground controls only as required.

2. Only qualified personnel in the platform may use the
platform controls. DO NOT CONTINUE OPERATION IF
CONTROLS DO NOT FUNCTION PROPERLY.

3. Rescue equipment can be used to remove the plat­form occupant(s). Cranes and forklifts can be used to
stabilize motion of the machine.

Platform Caught Overhead

If the platform becomes jammed or snagged in overhead struc­tures or equipment, rescue the platform occupant(s) prior to
freeing the machine.

Righting of Tipped Machine

A fork truck of suitable capacity or equivalent equipment
should be placed under the elevated side of the chassis, with a
crane or other suitable lifting equipment used to lift the plat­form while the chassis is lowered by the forklift or other equip­ment.

4.3 PLATFORM MANUAL DESCENT

The platform manual descent control is used in the event of
total power failure to retract and lower the platform using grav­ity. The manual descent control T-handle is located on the right
rear of the machine, just in front of the drive wheel. Look for the
instruction decal located beside the release handle.

The lowering procedure is as follows:

1. Locate the manual descent control T-handle.
(See Figure 4-1.)

KEEP HANDS AND ARMS OUT OF THE PATH OF THE SCISSOR ARMS AND PLAT­FORM WHILE LOWERING.

2. Grasp the T-handle and slowly pull out to lower the
scissor arms/platform, when the platform is lowered
to desired level, allow the T-handle to return to it’s
closed position.

3121272 – JLG Lift – 4-1

SECTION 4 - EMERGENCY PROCEDURES

NOTICE

4.4 INCIDENT NOTIFICATION

JLG Industries, Inc. must be notified immediately of any incident
involving a JLG product. Even if no injury or property damage is
evident, JLG must be contacted by telephone and provided
with all necessary details.

USA: 877-JLG-SAFE (554-7233)

EUROPE: (44) 1 698 811005

AUSTRALIA: (61) 2 65 811111

E-mail: [e-mail]

Failure to notify the manufacturer of an incident involving a JLG
Industries product within 48 hours of such an occurrence may
void any warranty consideration on that particular machine.

Figure 4-1. Location of Manual Descent Control

(Right Rear of Machine - All Machines)

4-2 – JLG Lift – 3121272

FOLLOWING ANY INCIDENT, THOROUGHLY INSPECT THE MACHINE. DO NOT
ELEVATE PLATFORM UNTIL YOU ARE SURE THAT ALL DAMAGE HAS BEEN
REPAIRED, AND THAT ALL CONTROLS ARE OPERATING CORRECTLY. TEST ALL
FUNCTIONS FIRST FROM THE GROUND CONTROL STATION, THEN FROM THE
PLATFORM CONTROL CONSOLE.

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

SECTION 5. GENERAL SPECIFICATIONS AND MAINTENANCE

5.1 INTRODUCTION

This section of the manual provides additional necessary infor­mation to the operator for proper operation and maintenance
of this machine.

The maintenance portion of this section is intended as informa­tion to assist the machine operator to perform daily mainte­nance tasks only, and does not replace the more thorough
Preventive Maintenance and Inspection Schedule included in
the Service and Maintenance Manual.

3121272 – JLG Lift – 5-1

Other Publications Available Specific to this Machine:

Service and Maintenance Manual......................................3121273

Illustrated Parts Manual .........................................................3121274

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

5.2 OPERATING SPECIFICATIONS

Table 5-1. Operating Specifications

DESCRIPTION 1932RS/6RS 3248RS/10RS

PLATFORM

Maximum Platform Height 19 ft. (5.79 m) 32 ft. (9.75 m)

DRIVING

M a xi m u m D r i ve S p e e d S to wed:

Elevated:

Maximum Stowed Travel Grade (Gradeability)
(Reference Figure 3-8. on page 3-13)

Inside Turning Radius 23.6 in. (0.6 m) 47.2 in. (1.2 m)

Outside Turning Radius 84.4 in. (2.22 m) 124.8 in. (3.17 m)

CHASSIS

Approximate Gross Machine Weight ANSI/CSA/JPN:

5-2 – JLG Lift – 3121272

Frame - P/N - 1001133090 - 3,000 lb. (1,360 kg)
P/N - 1001146792 - 3,450 lb. (1,565 kg)

CE:

3,450 lb. (1,565 kg)

2.5 mph (4 kph)

0.3 mph (0.5 kph)

25% (14°)

Frame - P/N - 1001129996 - 5,070 lb. (2,300 kg)
P/N - 1001146791 - 6,050 lb. (2,744 kg)

6,050 lb. (2,744 kg)

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Table 5-1. Operating Specifications (Continued)

DESCRIPTION 1932RS/6RS 3248RS/10RS

Maximum Tire Load (per wheel) ANSI/CSA/JPN:

CE:

1,365 lb. (620 kg)

1,835 lb. (832 kg)
2,070 lb. (940 kg)

CHASSIS (continued)

Ground Bearing Pressure ANSI/CSA/JPN:

CE:

130 PSI (9.18 kg/cm

2

)

81 PSI (5.69 kg/cm
108 PSI (7.6 kg/cm

2

)

2

)

Ground Clearance (Chassis Base Plate) 3 in. (76.2 mm) 4 in. (102 mm)

Maximum Hydraulic Pressure (Main Relief) 2300 psi (159 bar) 2500 psi (172 bar)

3121272 – JLG Lift – 5-3

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Platform Capacities

Table 5-2. Platform Capacities

MAXIMUM

SPECIFICATION MACHINE MODEL

ANSI/CSA/JPN 1932 500 Lb. (227 Kg) 250 Lb. (113 Kg) 2 100 Lb. (445 N) 28 mph

3248 705 Lb. (320 Kg) 250 Lb. (113 Kg) 2 100 Lb. (445 N) 28 mph

ANSI EXPORT 1932 480 Lb. (218 Kg) 240 Lb. (109 Kg) 2 100 Lb. (445 N) 28 mph

3248 683 Lb. (310 Kg) 236 Lb. (107 Kg) 2 100 Lb. (445 N) 28 mph

CE 6RS 230 Kg 120 Kg Indoor - 2 Persons + 70 Kg 400 N 0 m/s

10RS 320 Kg 120 Kg Indoor - 2 Persons + 160 Kg 400 N 0 m/s

NOTE: (1) Maximum Platform Capacity includes platform and platform extension.

5-4 – JLG Lift – 3121272

PLATFORM

CAPACITY

MAXIMUM CAPACITY

(1)

ALLOWED ON

PLATFORM EXTENSION

MAXIMUM PERSONS

ALLOWED IN PLATFORM

Outdoor - 1 Person + 150 Kg 200 N 12.5 m/s

Outdoor - 1 Person + 240 Kg 200 N 12.5 m/s

MAX. SIDE FORCE

(Platform Fully Extended

@ Max. Capacity)

MAXIMUM

OPERATING

WIND SPEED

Machine Dimensional Data

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Table 5-3. Dimensions

DESCRIPTION 1932RS/6RS 3248RS/10RS

Platform Height - Elevated
(Ground to Platform Floor)

Platform Height - Stowed
(Ground to Platform Floor)

Working Height 25 ft. (7.6 m) 38 ft. (11.5 m)

Rail Height
(Platform Floor to Top of Rail)

Rail Height - Folded
(Ground to Mid R ail)

Overall Machine Width 32 in. (81.28 cm) 48 in. (122 cm)

Overall Machine Length

Platform Size - Length 71.7 in. (1.82 m) 84.75 in. (2.15 m)

Platform Size - Width 26.9 in. (68.4 cm) 42.5 in. (1.07 m)

Wheelbase 55 in. (139.7 cm) 73 in. (185.4 cm)

3121272 – JLG Lift – 5-5

19 ft. (5.79 m) 32 ft. (9.75 m)

39.5 in. (100 cm) 54.75 in. (139 cm)

40 in. (101.6 cm)

69.3 in. (176 cm) - CE ONLY

81.4 in. (2.07 m)

41 in. (104.3 cm) - ANSI

43.6 in. (110.7 cm) - CE

78.3 in. (198.9 cm)- ANSI

77.6 in. (197.1 cm) - CE

90 in. (2.28 m) - ANSI

94.8 in. (240.7 cm) - CE

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Tires

Table 5-4. Tire Specifications

DESCRIPTION 1932RS/6RS 3248RS/10RS

Size 12.71 in. x 3.94 in.

(323 mm x 100 mm)

Wheel Bolt Torque 120 ft lb. (163 Nm)

16 in. x 5 in.

(406 mm x 127 mm)

Batteries

Table 5-5. Battery Specifications

DESCRIPTION ALL MACHINES

Voltage (24V System - Series) 6 V per battery

Amp Hour (Standard Battery) 220 Amp Hour @ 20 HR. Rate

Reserve Capacity (Standard Battery) 447 Minutes

Electrical System

Table 5-6. Electrical System Specifications

DESCRIPTION ALL MACHINES

Electrical System Voltage (DC) 24V

Battery Charger: (1001129847)

Input:

AC Inp ut Volta ge:

Nominal AC Input Voltage:

Input Frequency:

Max. AC Input Current:

Ingress Protection:

Operatin g Temperature:

Output:

Nominal DC Output Voltage:

Max. DC Output Voltage:

Max DC Output Current:

Max. Interlock Current:

Protection:

Output Reverse Polarity:

Output Short Circuit:

AC Ove rloa d:
DC Overload:

DC t o A C I n ve r te r - O ut p ut R at in g :
(OPTION)

85-265V AC
120VAC / 230VAC RMS
45 - 65Hz
12A - RMS @ 108V AC
IP46 NEMA4 Type 4

-22°F (-30°C) to 122°F (+50°C)

24V

33.6V
25A
1A

Electronic Protection-Auto Reset
Electronic Protection-Auto Reset
Current Li mited
Current Li mited

120V-AC, 60Hz - 7.5 Amps - 900 Watts ­Mod. Sinewave

5-6 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

5.3 CRITICAL STABILITY WEIGHTS

DO NOT REPLACE ITEMS CRITICAL TO STABILITY, SUCH AS BATTERIES OR
SOLID TIRES, WITH ITEMS OF DIFFERENT WEIGHT OR SPECIFICATION. DO
NOT MODIFY UNIT IN ANY WAY TO AFFECT STABILITY.

Table 5-7. Critical Stability Weights

COMPONENT 1932RS/6RS 3248RS/10RS

Wheel and Tire Assembly (each)

Front:

Rear:

Wheel/Tire and Drive Assembly
(each)

Batteries (each) Standard:

AGM:

Batteries (combined) Standard :

AGM:

21.6 lb. (9.8 kg)

21.6 lb. (9.8 kg)

113 lb. (51.3 kg) 134 lb. (60.8 kg)

248 lb. (111.1 kg)

43 lb. (19.5 kg)

40.5 lb. (18.4 kg)

62 lb. (28.1 kg)
65 lb. (29.5 kg)

260 lb. (118 kg)

5.4 LUBRICATION

Lubrication Capacities

Table 5-8. Capacities

COMPONENT 1932RS/6RS 3248RS/10RS

Hydraulic

Reservoir 1.32 Gal. (5 L) 2.38 Gal. (9 L)

Hydraulic System
(Including

Reservoir)

1.85 Gal. (7 L) 3.96 Gal. (15 L)

Hydraulic Oil

Table 5-9. Hydraulic Oil

HYDRAULIC SYSTEM OPERATING

TEMPERATURE RANGE

0° F to +23° F (-18° C to -5° C) 10W

0° F to 210° F (-18° C to + 99° C) 10W-20, 10W-30

50° F to 210° F (+10° C to +210° C) 2 0W-20

NOTE: Aside from JLG recommendations, it is not advisable to

mix oils of different brands or types, as they may not con­tain the same required additives or be of comparable vis­cosities.

SAE VISCOSITY GRADE

3121272 – JLG Lift – 5-7

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Lubrication Specifications

Table 5-10. Lubrication Specifications

KEY SPECIFICATIONS

MPG Multipurpose Grease having a minimum dripping point of 350° F. Excel-

lent water resistance and adhesive qualities, and being of extreme pres­sure type. (Timken OK 40 pounds minimum.)

EPGL Ex treme Pressure Gear Lube (oil) meeting API service classification GL-5 or

MI L-S pe c M IL- L-2 10 5.

HO JLG Recommends - Mobil DTE 10 EXCEL 15

ATF - Automatic Transmission Fluid

Mobil EAL ENVIRONSYN H 32

Mobil EAL HYDRAULIC OIL 32

Table 5-11. Hydraulic Oil Specifications

MOBIL

SPECIFICATION

ISO Viscosity Grade #15 #32 #32

Spec Gravity API 31.9 0.950 —

Pour Point, M ax

Flash Point, Min. 330° F (166° C) 514.4° F (268° C) 478° F (248° C)

VISCOSITY SPECIFICATIONS

at 40° C 15 cSt

at 100° C 4.1 cSt

at 100° F 80 SUS

at 210° F 43 SUS

cp at -30° F 3.2

Viscosity Index 140 147 189

Operating Temp — -20° F (-29° C) to 200° F (93° C)

DTE 10

EXCEL 15

-40° F

(-40° C)

MOBIL EAL

ENVIRONSYN

H 32

-59° F

(-51° C)

33.1 cSt 32 cSt

6.36 cSt 7 cSt

——

——

——

MOBIL EAL

HYDRAULIC OIL 32

-38.2° F
(-39° C)

1001102685_3

5-8 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

1

2

3

4

5.5 MAINTENANCE

NOTE: Care should be taken not to introduce any impurities (dirt,

water, etc.) while cap is removed.

Hydraulic Oil Check Procedure

Lube Point(s) - Hydraulic Reservoir
Reservoir Capacity - See Table 5-8 on page 5-7.
Lube - Hydraulic Oil
Interval - Check Daily

NOTE: Check the hydraulic oil level with the platform in the

stowed position ONLY. Be certain the hydraulic oil has
warmed to operating temperature before checking the oil
level in the reservoir.

1. On the left side of the machine, remove the side
access door on the base frame. Locate the hydraulic
oil reservoir (1) on the pump unit (2). Check the oil

level in the hydraulic reservoir by looking at the mark­ings on the side. The reservoir is marked with a MAX
(maximum) marking (3). The oil level must be kept at
or within one (1) inch of this marking to operate prop­erly.

2. If additional oil is required, wipe all dirt and debris
from the filler/breather cap (4) area, add proper
grade of oil. Fill until oil level is close to the MAX

marking (3), but not over the MAX marking.

Figure 5-1. Hydraulic Oil Check Procedure - All Machines

NOTE: Recommended lubricating intervals are based on

machine operations under normal conditions. For
machines used in multi-shift operations and/or exposed
to hostile environments or conditions, lubrication fre­quencies must be increased accordingly.

3121272 – JLG Lift – 5-9

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

1/8 "

BATTERY

FILLER CAP

FLUID LEVEL OF FULLY

CHARGED BATTERY

VENT TUBE

PLATES

1706740A

5.6 BATTERY MAINTENANCE

Battery Maintenance and Safety Practices

NOTE: These instructions are for unsealed (wet) batteries only.

if machine is equipped with sealed batteries, no mainte­nance other than cleaning corroded battery terminals is
required.

ENSURE THAT BATTERY ACID DOES NOT COME INTO CONTACT WITH SKIN OR
CLOTHING. WEAR PROTECTIVE CLOTHING AND EYEWEAR WHEN WORKING
WITH BATTERIES. NEUTRALIZE ANY BATTERY ACID SPILLS WITH BAKING
SODA AND WATER.
BATTERY ACID RELEASES AN EXPLOSIVE GAS WHILE CHARGING, ALLOW NO
OPEN FLAMES, SPARKS OR LIGHTED TOBACCO PRODUCTS IN THE AREA
WHILE CHARGING BATTERIES. CHARGE BATTERIES ONLY IN A WELL VENTI­LATED AREA.
ADD ONLY DISTILLED WATER TO BATTERIES. WHEN ADDING DISTILLED
WATER TO THE BATTERIES, A NON-METALLIC CONTAINER AND/OR FUNNEL
MUST BE USED.

Check the electrolyte level of the batteries often, adding only
distilled water when required. When fully charged, battery fluid
level should be 1/8" below vent tubes. (See Figure 5-2.).

• DO NOT fill to bottom of vent tubes.

• DO NOT allow fluid level to go below the top of the plates

Figure 5-2. Battery Fluid Level.

Battery Quick-Disconnect ­(If Equipped)

Machines equipped with the battery
quick-disconnect allow all machine
power to be easily disconnected at the
batteries without removing battery cables from the battery
posts. To disconnect power, locate the RED quick-disconnect
connector on top of the batteries inside the battery compart­ment and pull halves apart.

5-10 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

5.7 TIRES AND WHEELS

Tire Wear and Damage

The tire and rim assemblies installed on RS machines have been
approved by the tire manufacturer for applications in which
those products are intended to be used. The tire and rims
installed on each product model have been designed for stabil­ity requirements, which consist of track width, tire compound,
and load capacity. Tire changes such as rim width, centerpiece
location, larger or smaller diameter, tire compound, etc., with­out written manufacturers approval, could result in an unsafe
condition regarding stability.

The tires and rims installed on RS machines are to be inspected
daily as part of the daily walk-around inspection. JLG requires
that the daily walk-around inspection be performed at each
operator change during a shift and at each shift change.

Wheel and Tire Replacement

JLG recommends that any replacement tire be the same size
and brand as originally installed on the machine or offered by
JLG as an approved replacement. Please refer to the JLG Parts
Manual for the part number of the approved tires for a partic­ular machine model.

If any of the following is discovered during tire inspection,
measures must be taken to remove the JLG product from ser­vice immediately. Arrangements must be made for replace­ment of the tire(s) or tire assembly(s). Both tires/wheels on the
same axle must be replaced:

• If the overall diameter of the tire is less than one of the fol­lowing:

100 x 323 Tire – 12.25 in. (311mm) minimum
127 x 406 Tire – 15.50 in. (394mm) minimum

• If any uneven wear is discovered.

A tire with significant damage in the tread area or sidewall
requires immediate evaluation before placing the machine
into service. If a cut, tear, chunk, or other discrepancy
exceeds any one or more of the following dimensions, the
tire must be replaced:

3.0 in. (76 mm) long

0.75 in. (19 mm) wide

0.75 in. (19 mm) deep

• If the metal wheel is visible at any point through the tread
area of the tire.

• If more than one discrepancy exists in any quadrant of the
wheel (within 90 degrees of one another).

3121272 – JLG Lift – 5-11

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

1

2

3

4

5

2

3

4

6

5

1

Wheel Installation

Check torque every 3 months or 150 hours of opera­tion.

It is extremely important to apply and maintain proper wheel
mounting torque.

WHEEL LUG NUTS MUST BE INSTALLED AND MAINTAINED AT THE PROPER
TORQUE TO PREVENT LOOSE WHEELS, BROKEN LUG NUTS, AND POSSIBLE
SEPARATION OF WHEEL FROM THE AXLE. BE SURE TO USE ONLY THE LUG
NUTS MATCHED TO THE CONE ANGLE OF THE WHEEL.

Tighten the lug nuts to the proper torque to prevent wheels
from coming loose. Use a torque wrench to tighten the fasten­ers. Over-tightening will result in breaking the lug nuts or per­manently deforming the mounting holes in the wheel. The
proper procedure for attaching wheels is as follows:

1. Start all lug nuts by hand to prevent cross threading.

Figure 5-3. Wheel Lug Nut Tightening Sequence

5 LUG WHEEL 6 LUG WHEEL

DO NOT use a lubricant on threads or nuts.

2. Tighten lug nuts in the following sequence. (See Figure
5-3.)

3. The tightening of the lug nuts should be done in
stages. Following the recommended sequence,
tighten lug nuts per wheel torque.

4. Wheel lug nuts should be torqued after the first 50
hours of operation and after each wheel removal.

5-12 – JLG Lift – 3121272

1st Stage 2nd Stage 3rd Stage

20-30 ft. lb.

(28 - 42 Nm)

Table 5-12. Wheel Torque Chart

TORQUE SEQUENCE

65-80 ft. lb.

(91 - 112 Nm)

(142 - 163 Nm)

105 -120 ft. lb.

5.8 DECAL INSTALLATION

3

1

2

5

6

7

9

10

11

12

13

14

16

17

19

21

20

22

24

25

(1932/6RS)

25

(3248/10RS)

8

15

4

13

14

26

18

18

23

(3248/10RS)

4

(1932/6RS)

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

3121272 – JLG Lift – 5-13

Figure 5-4. Machine Decal Installation - All Machines

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Table 5-13. Machine Decal Installation Chart (See Figure 5-4.)

ITEM

1 1001131270 — 1001131270 1001131270 — — —

2 1701504 1701504 1701504 1701504 1701504 1701504 1701504

3 1701509 1701509 1701509 1701509 1701509 1701509 1701509

4 1001136794 1001136794 1001136794 1001136794 1001136794 1001136794 1001146795

5 1703819 1703819 1703819 1703819 1703819 1703819 1703819

6 1703822 1703822 1703822 1703822 1703822 1703822 1703822

7 1704016 1704016 1704016 1704016 1704016 1704016 1704016

8 1704277 1704277 1704277 1704277 1704277 1704277 1704277

9 1704412 1704412 1704412 1704412 1704412 1704412 1704412

10

11 1705679 1705679 1705727 1705679 1705679 1705679 —

12 1705686 1705720 1705726 1705723 (CAN) 1705946 1706057 1001092497

ANSI/

CSA

1706311 -

3248RS/10RS

1704134 -

1932RS/6RS

ANSI

(LAT)

1706311 -

3248RS/10RS

1704134 -

1932RS/6RS

ANSI

(BRZ)

1706311 -

3248RS/10RS

1704134 -

1932RS/6RS

ANSI

(FRE)

1706311 -

3248RS/10RS

1704134 -

1932RS/6RS

ANSI
(CHI)

1706311 -

3248RS/10RS

1704134 -

1932RS/6RS

ANSI

(KOR)

1706311 -

3248RS/10RS

1704134 -

1932RS/6RS

CE/JPN

(ALL)

1001147258 -

3248RS/10RS

1001147259 -

1932RS/6RS

5-14 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Table 5-13. Machine Decal Installation Chart (See Figure 5-4.)

ITEM

13 1705694

14 1705695

15 1001115695 1001115695 1001115695 1001115695 1001115695 1001115695

16 4110226 4110226 4110226 4110226 4110226 4110226 4110226

17 1001132359 1001132359 1001132359 1001132359 1001132359 1001132359 1001132359

18

19 1001132376 1001132376 1001132396 1001132376 1001132376 1001132376 —

20

21 1001134280 1001134280 1001134280 1001134280 1001134280 1001134280 1001134280

ANSI/

CSA

1001132364 -

3248RS/10RS

1705699 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

ANSI

(LAT)

1705694

1705725 (SPA)

1705695

1705724 (SPA)

1001132364 -

3248RS/10RS

1705699 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

ANSI

(BRZ)

1705722

1705725 (POR)

1703834

1702724 (POR)

1001132364 -

3248RS/10RS

1705699 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

ANSI

(FRE)

1705694

1705717 (CAN)

1705695

1705718 (CAN)

1001132364 -

3248RS/10RS

1705699 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

ANSI
(CHI)

1705694

1705943 (CHI)

1705695

1705944 (CHI)

1001132364 -

3248RS/10RS

1705699 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

ANSI

(KOR)

1705694

1706052 (KOR)

1705695

1706056 (KOR)

1001132364 -

3248RS/10RS

1705699 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

CE/JPN

(ALL)

1705673

1705671

1001115696 - CE

1001115697- JPN

1001146903 -

3248RS/10RS

1001146902 -

1932RS/6RS

1001133159 -

3248RS/10RS

1001137394 -

1932RS/6RS

3121272 – JLG Lift – 5-15

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

Table 5-13. Machine Decal Installation Chart (See Figure 5-4.)

ITEM

22 1706350 1706350 1706350 1706350 1706350 1706350 170635014

23 1703072 1703072 1703072 1703072 1703072 1703072 1703072

24 — 1705719 (SPA) 1705719 (POR) 3253098 (CAN) 1705945 (CHI) 1706053 (KOR) —

25 1703464 1703464 1703464 1703464 1703464 1703464 3252507

26 1705303 (CSA) ————— —

NOTE: Reference applicable Illustrated Parts Manual for decal description.

ANSI/

CSA

ANSI

(LAT)

ANSI

(BRZ)

ANSI

(FRE)

ANSI
(CHI)

ANSI

(KOR)

CE/JPN

(ALL)

5-16 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

NOTICE

5.9 DIAGNOSTIC TROUBLE CODES (DTC)

The DTC tables following are sorted in groups by the first two
digits, these digits represent the number of flashes the system
distress indicator lamp will flash on the platform indicator panel
when a fault occurs.

For example: a “2-1 Power-Up” on page 19 would be indicated
by 2 flashes, a pause, then 1 flash, a pause, then would keep
repeating until the fault is cleared.

The more detailed three digit code numbers in the DTC column
of the following tables are only indicated on a JLG handheld
diagnostic analyzer.

To troubleshoot multiple DTCs, start with the DTC with the
higher first two digits. If a correction is made during a check,

conclude the check by cycling the machine power off then
back on, using the emergency stop switch.

SHOULD A FAULT OCCUR WHICH CANNOT BE CORRECTED BY THE OPERATOR,
THE PROBLEM MUST BE REFERRED TO A MECHANIC QUALIFIED TO REPAIR
THIS MODEL OF JLG LIFT.

5.10 DTC CHECK TABLE INDEX

DTC TABLE PAGE

0-0 Help Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18

2-1 Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19

2-2 Platform Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19

2-3 Ground Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-20

2-5 Function Prevented . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-21

3-1 Line Contactor Open Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22

3-2 Line Contactor Short Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22

3-3 Ground Output Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22

4-2 Thermal Limit (SOA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-24

4-4 Battery Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25

6-6 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25

7-7 Electric Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-26

8-2 LSS - Load Sensing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-27

8-4 Elevation Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-28

9-9 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-28

3121272 – JLG Lift – 5-17

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

5.11 DIAGNOSTIC TROUBLE CODES (DTC) CHECK TABLES

0-0 Help Comments

DTC FAULT MESSAGE DESCRIPTION CHECK

001 EVERYTHING OK The normal help message in platform mode.

Displays on the analyzer only.

002 GROUND MODE OK The normal help message in ground mode.

Displays on the analyzer only.

004 DRIVING AT CUTBACK - ABOVE ELEVA-

TION

005 DRIVE & LIFT UP PREVENTED - TILTED &

ELEVATED

008 FUNCTIONS LOCKED OUT - SYSTEM

POWERED DOWN

The platform is elevated and the machine is in
the driving in creep speed.

Driving is not possible since the platform is
elevated and the chassis is not level.

After 2 hours without activity, the control sys­tem enters a low-power st ate to preser ve bat­tery c harge.

• Fully stow the platform.

• Check that the elevation sensor is securely mounted.

Refer problem to a qualified JLG mechanic.

• Check that the machine is tilted. If so, lower the platform and reposition the
machine to a level surface.

• Fully stow the platform.

• Check that the tilt sensor is securely mounted.

• Check that the elevation sensor is securely mounted.

Refer problem to a qualified JLG mechanic.

• Normal operation should resume after power is cycled off then back on.

• Check batteries charge, condition, etc.

Refer problem to a qualified JLG mechanic.

5-18 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

2-1 Power-Up

DTC FAULT MESSAGE DESCRIPTION CHECK

211 POWER CYCLE This help message is issued at each power

cycle. Displays on the analyzer only.

Normal operation. No check necessary.

2-2 Platform Controls

DTC FAULT MESSAGE DESCRIPTION CHECK

221 FUNCTION PROBLEM - HORN PERMA-

NENTLY SELECTED

223 FUNCTION PROBLEM - DRIVE & LIFT

ACTIVE TOGETHER

224 FUNCTION PROBLEM - STEER LEFT PER-

MANENTLY SELECTED

225 FUNCTION PROBLEM - STEER RIGHT

PERMANENTLY SELECTED

226 ACCELERATOR FAULT Y - WIPER OUT OF

RANGE

227 STEER SWITCHES FAULTY The steer left and steer right inputs were

The horn switch was closed during power-up
in platform mode.

The drive and lift inputs are closed simultane­ously in platform mode.

The steer left switch was closed during power­up in platform mode.

The steer right switch was closed during
power-up in platform mode.

There is a problem with the joystick. • Center joystick and check to see if a power cycle will clear DTC.

closed simultaneously.

• Check if the horn switch is damaged, obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Check drive/lift switch for visible damage.

Refer problem to a qualified JLG mechanic.

• Check if the steer left switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Check if the steer right switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

• Check if the steer switches are damaged, obstructed or jammed.

Refer problem to a qualified JLG mechanic.

3121272 – JLG Lift – 5-19

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

2-2 Platform Controls

DTC FAULT MESSAGE DESCRIPTION CHECK

228 FUNCTION LOCKED OUT - ACCELERATOR

NOT CENTERED

229 FUNCTION PROBLEM - TRIGGER PER-

MANENTLY CLOSED

2210 TRIGGER CLOSED TOO LONG WHILE IN

NEUTRAL

2232 FUNC TION PROBLEM - DRIVE & LIFT

BOTH OPEN

The joystick was not centered at power-up. • Release joystick and allow to center.

• Check if the joystick is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

The trigger switch was closed during power­up in platform mode.

The trigger switch was closed for more than
five seconds while the joystick was centered.

The drive and lift inputs are both de-energized
in platform mode.

• Check if the trigger switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Check if the trigger switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Check if either function is active, if Yes;
Refer problem to a qualified JLG mechanic.

2-3 Ground Controls

DTC FAULT MESSAGE DESCRIPTION CHECK

231 FUNCTION PROBLEM - LIFT PERMA-

NENTLY SELECTED

232 GROUND LIFT UP / DOWN ACTIVE

TOGETHER

233 FUNCTION PROBLEM - BRAK E RELEASE

PERMANENTLY SELECTED

5-20 – JLG Lift – 3121272

The ground control box lift switch was closed
up or down, during power-up in ground mode.

The lift up / down inputs are closed simultane­ously.

The electric brake release switch was closed
during power-up.

• Check if the lift switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Check if the lift switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Check if the brake release switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

2-5 Function Prevented

DTC FAULT MESSAGE DESCRIPTION CHECK

253 DRIVE PREVENTED - CHARGER CON-

NECTED

254 DRIVE & LIFT UP PREVENTED - CHAR-

GER CONNECTED

255 PLATFORM OVERLOAD The Load Sensing System (LSS) measured

258 DRIVE & LIFT PREVENTED - BRAKES

ELECTRICALLY RELEASED FOR TOWING

259 MODEL CHANGED - HYDRAULICS SUS-

PENDED - CYCLE EMS

2510 DRIVE PREV ENTED - BRAKES NOT

RELEASING

Driving is not possible while the vehicle is
charging.

Drive or lift is not possible while the vehicle is
charging AND is configured to prevent all
motion.

platform load is excessive.

Electric brake release mode is activated with
the switch in the battery box near the ground
control box. Drive or lift is not possible.

The model selection has been changed. Refer problem to a qualified JLG mechanic.

There is a problem with the drive or brake sys­tem.

• Check if the charger is connected to off board power source and disconnect if
desired.

Refer problem to a qualified JLG mechanic.

• Check if the charger is connected to off board power source and disconnect if
desired.

Refer problem to a qualified JLG mechanic.

• Remove excess weight from the platform.

• Check that platform is not caught on something, preventing up or down

movement.

Refer problem to a qualified JLG mechanic.

• Push manual brake release switch again or cycle power to clear manual brake
release mode.

• Check if the brake release switch is obstructed or jammed.

Refer problem to a qualified JLG mechanic.

• Ensure vehicle is not stuck on something preventing movement.

Refer problem to a qualified JLG mechanic.

3121272 – JLG Lift – 5-21

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

3-1 Line Contactor Open Circuit

DTC FAULT MESSAGE DESCRIPTION CHECK

311 OPEN CIRCUIT LINE CONTACTOR There is a problem with the line contactor. Refer problem to a qualified JLG mechanic.

314 AUXILIARY RELAY - OPEN CIRCUIT The auxiliary relay did not close when ener-

gized.

• Check the auxiliary relay coil and the associated wiring.

Refer problem to a qualified JLG mechanic.

3-2 Line Contactor Short Circuit

DTC FAULT MESSAGE DESCRIPTION CHECK

321 LINE CONTACTOR MISWIRED ON OR

WELDED

326 AUXILIARY RELAY - SHORT TO BATTERY There is a problem with the auxiliary relay con-

There is a problem with the line contactor. Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

tacts or wiring.

3-3 Ground Output Driver

DTC FAULT MESSAGE DESCRIPTION CHECK

333 LIFT UP SHORT TO BATTERY A problem has been detec ted in this function. Refer problem to a qualified JLG mechanic.

334 LIFT UP OPEN CIRCUIT A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

335 LIFT DN SHORT TO BATTERY A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

336 LIFT DN OPEN CIRCUIT A problem has been detected in this fun ction. Refer problem to a qualified JLG mechanic.

5-22 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

3-3 Ground Output Driver

DTC FAULT MESSAGE DESCRIPTION CHECK

337 STEER LEFT SHORT TO BATTERY A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

338 STEER LEFT OPEN CIRCUIT A problem has been detec ted in this function. Refer problem to a qualified JLG mechanic.

339 STEER RIGHT SHORT TO BATTERY A problem has been detected in this func tion. Refer problem to a qualified JLG mechanic.

3310 STEER RIGHT OPEN CIRCUIT A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

3312 LEFT BRAK E SHORT TO BATTERY A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

3313 RIGHT BRAKE SHORT TO BATTERY A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

3314 LEFT BRAK E OPEN CIRCUIT A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

3315 RIGHT BRAKE OPEN CIRCUIT A problem has been detec ted in this function. Refer problem to a qualified JLG mechanic.

3349 LINE CONTACTOR COIL - SHORT TO

GROUND

33297 LEFT BRAKE - SHORT TO GROUND A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

33298 STEER LEFT VALVE - SHORT TO GROUND A problem has been detected in this func tion. Refer problem to a qualified JLG mechanic.

33299 LINE CONTACTOR COIL - SHORT TO BAT-

TERY

33302 NEGATIVE SUPPLY - SHORT TO BATTERY A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

33303 NEGATIVE SUPPLY - SHORT TO GROUND A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

33304 RIGHT BRAKE - SHORT TO GROUND A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

3121272 – JLG Lift – 5-23

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

3-3 Ground Output Driver

DTC FAULT MESSAGE DESCRIPTION CHECK

33305 STEER RIGHT VALVE - SHORT TO

GROUND

33406 LIFT UP VALVE - SHORT TO GROUND A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

33407 LIFT DN VALVE - SHORT TO GROUND A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

A problem has been detected in this function. Refer problem to a qualified JLG mechanic.

4-2 Thermal Limit (SOA)

DTC FAULT MESSAGE DESCRIPTION CHECK

421 POWER MODULE TOO HOT - PLEASE

WAI T

422 DRIVING AT CUTBACK - POWER MOD-

ULE CURRENT LIMIT

423 LIFT UP AT CUTBACK - POWER MODULE

CURRENT LIMIT

5-24 – JLG Lift – 3121272

The power module has reached thermal cut­out.

The drive portion of the power module has
reached thermal limit.

The lift up portion of the power module has
reached thermal limit.

• Power down and allow to cool.

• Do not operate in ambients over 140° F (60° C).

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

4-4 Battery Supply

DTC FAULT MESSAGE DESCRIPTION CHECK

441 BATTERY VOLTAGE TOO LOW - SYSTEM

SHUTDOWN

442 BATTERY VOLTAGE TOO HIGH - SYSTEM

SHUTDOWN

446

LOGIC SUPPLY VOLTAGE OUT OF RANGE The System Module logic supply voltage was
4421
4422

A problem has been detected with the batter­ies or power module.

A problem has been detected with the batter­ies or power module.

m e a s u r e d t o b e o u t o f n o r m a l o p e r a t i n g r a n g e .

• Recharge batteries or check for damaged batteries.

• Check battery charger function.

Refer problem to a qualified JLG mechanic.

• May be due to improper battery charging or incorrect voltage batteries being
used.

Refer problem to a qualified JLG mechanic.

• Check for severely discharged battery, loose cables or for damaged battery;
otherwise;

• Refer problem to a qualified JLG mechanic.

6-6 Communication

DTC FAULT MESSAGE DESCRIPTION CHECK

661 CANBUS FAILURE - POWER MODULE The control system failed to receive messages

from the power module.

6643 CANB US FAILURE - LSS ANGLE SENSOR The control system failed to receive messages

from the angle sensor.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

3121272 – JLG Lift – 5-25

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

7-7 Electric Motor

DTC FAULT MESSAGE DESCRIPTION CHECK

772 STALLED TRACTION MOTOR OR POWER

WIRING ERROR

773 CAPACITOR BANK FAULT - CHECK

POWER CIRCUITS

774 SHORT CIRCUIT FIELD WIRING The power module detected a problem in the

775 OPEN CIRCUIT FIELD WIRING The power module detected a problem in the

776 STALLED PUMP MOTOR OR POWER

WIRING ERROR

777 OPEN CIRCUIT PUMP MOTOR WIRING The power module detected a problem in the

778 TRACTION T HIGH - CHECK POWER CIR-

CUITS

779 TRACTION T LOW - CHECK POWER CIR-

CUITS

7710 PUMP P HIGH - CHECK POWER CIRCUITS The power module detected a problem in the

The power module detected a problem in the
drive motors' power circuit wiring.

The power module detected a problem in the
pump or drive motors' power circuit wiring.

drive motors' power circuit wiring.

drive motors' power circuit wiring.

The power module detected a problem in the
drive motors' power circuit wiring.

drive motors' power circuit wiring.

The power module detected a problem in the
drive motors' power circuit wiring.

The power module detected a problem in the
drive motors' power circuit wiring.

drive motors' power circuit wiring.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

5-26 – JLG Lift – 3121272

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

7-7 Electric Motor

DTC FAULT MESSAGE DESCRIPTION CHECK

7711 PUMP P LOW - CHECK POWER CIRCUITS The power module detected a problem in the

drive motors' power circuit wiring.

7741 ARMATURE BRAKING CURRENT TOO

HIGH

7742 FIELD VOLTAGE IMPROPER The power module detected a problem in the

The power module has detected excessive
braking current.

drive motors' power circuit wiring.

Refer problem to a qualified JLG mechanic.

Th i s c a n b e c a us e d b y t r an s po r ti n g a n ex ce s si ve l oa d o n a s t ee p g r ad e.

Recycle power on/off, if problem persists;

Refer problem to a qualified JLG mechanic.

8-2 LSS - Load Sensing System

DTC FAULT MESSAGE DESCRIPTION CHECK

8212 LSS PRESSURE SENSOR -

DISAGREEMENT

8213 LSS ANGLE SENSOR -

DISAGREEMENT

8214 LSS ANGLE SENSOR -

DIRECTION DISAGREEMENT

3121272 – JLG Lift – 5-27

Pressure Sensor 1 and Pressure Sensor 2 do not
agree. The system shall assume the machine is
overloaded until the sensors agree.

The angle sensor’s change in reading does not
agree with the direction of themachine
motion (lift up).

The angle sensor’s reading when the machine
is at maximum elevation does not fall within
the high end acceptable range.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

8-2 LSS - Load Sensing System

DTC FAULT MESSAGE DESCRIPTION CHECK

8215 LSS ANGLE SENSOR -

OUT OF RANGE LOW

8216 LSS ANGLE SENSOR HAS NOT BEEN CAL-

IBRATED

The angle sensor’s reading when the machine
is stowed does not fall within the low end
acceptable range.

The Angle Sensor has never been calibrated
and the control system assumes that the plat­form is overloaded.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

8-4 Elevation Switch

DTC FAULT MESSAGE DESCRIPTION CHECK

84109 ELEVATION SWITCH CONTACTS DIS-

AGREEMENT

The elevation switch is repeating an incorrect
value.

Refer problem to a qualified JLG mechanic.

9-9 Hardware

DTC FAULT MESSAGE DESCRIPTION CHECK

995 POWER MODULE FAILURE - PERSONAL-

ITY RANGE ERROR

996 POWER MODULE FAILURE - INTERNAL

ERROR

5-28 – JLG Lift – 3121272

A problem has been detected with the power
module.

A problem has been detected with the power
module.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

9-9 Hardware

DTC FAULT MESSAGE DESCRIPTION CHECK

998 EEPROM FAILURE - CHECK ALL SET-

TINGS

999 FUNCTION LOCKED OUT - POWER MOD-

ULE SOFTWARE VERSION IMPROPER

The control system detected an EEPROM fail­ure.

The power module software version i s not
compatible with the rest of the system.

Refer problem to a qualified JLG mechanic.

Refer problem to a qualified JLG mechanic.

3121272 – JLG Lift – 5-29

SECTION 5 - GENERAL SPECIFICATIONS AND MAINTENANCE

9-9 Hardware

DTC FAULT MESSAGE DESCRIPTION CHECK

POWER MODULE FAILURE - INTERNAL

9950

ERROR

9951
9952
9953
9954
9955
9956
9957
9958
9960
9962
9963
9964
9969
9970

9971
99143
99144
99145
99146
99147
99148
99149

A problem has been detected with the power
module.

Cycle machine power on /off a few times if this doesn’t clear the DTC,
refer problem to a qualified JLG mechanic.

5-30 – JLG Lift – 3121272

SECTION 6. INSPECTION AND REPAIR LOG

Machine Serial Number _____________________________________ __

Table 6-1. Inspection and Repair Log

DATE COMMENTS

SECTION 6 - INSPECTION AND REPAIR LOG

3121272 – JLG Lift – 6-1

SECTION 6 - INSPECTION AND REPAIR LOG

Table 6-1. Inspection and Repair Log

DATE COMMENTS

6-2 – JLG Lift – 3121272

Corporate Office

JLG Industries, Inc.

1 JLG Drive

McConnellsburg, PA 17233-9533 USA

[phone] (Corporate)

[phone] (Customer Support)

[phone]

Visit our website for JLG Worldwide Locations.

www.jlg.com