Operator's Manual
MZ5225 / 968999717 |
MZ6125 / 968999718 |
MZ7227 / 968999719 |
MZ5225BF / 968999720 |
MZ6125BF / 968999721 |
MZ5225C / 968999748 |
MZ6125C / 968999749 |
MZ25 / 968999780 |
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
English
©2008 HTC. All rights reserved. Beatrice, NE. Printed in U.S.A.
Contents
INTRODUCTION............................................................... |
5 |
General........................................................................ |
5 |
Driving and Transport on Public Roads....................... |
5 |
Towing......................................................................... |
5 |
Operating..................................................................... |
5 |
Good Service............................................................... |
6 |
Symbols and Decals.................................................. |
7 |
Safety............................................................................. |
9 |
Safety Instructions....................................................... |
9 |
General Operation....................................................... |
9 |
Personal Safety Equipment....................................... |
11 |
Slope Operation........................................................ |
11 |
Safe Handling of Gasoline......................................... |
13 |
General Maintenance................................................ |
14 |
Transport................................................................... |
16 |
Roll over Protection system (ROPS)......................... |
17 |
Controls..................................................................... |
18 |
Control Locations...................................................... |
18 |
Steering Control Levers............................................. |
19 |
Parking Brake............................................................ |
20 |
Throttle Control.......................................................... |
20 |
Blade Switch.............................................................. |
20 |
Ignition Switch........................................................... |
21 |
Choke Control........................................................... |
21 |
Fuses......................................................................... |
21 |
Fuel Tank................................................................... |
22 |
Fuel Shut Off Valve................................................... |
23 |
Hour Meter................................................................ |
24 |
Tracking Knob........................................................... |
24 |
Operation.................................................................... |
25 |
Training..................................................................... |
25 |
Steering..................................................................... |
25 |
Before Starting.......................................................... |
26 |
Starting the Engine.................................................... |
26 |
Jumper cables................................................. |
30 |
Running..................................................................... |
31 |
Operating on hills...................................................... |
32 |
Mowing Tips ............................................................. |
33 |
Stopping the Engine.................................................. |
34 |
Pump release valves................................................. |
35 |
Maintenance............................................................... |
36 |
Maintenance Schedule.............................................. |
36 |
Battery....................................................................... |
38 |
Ignition System.......................................................... |
39 |
Safety System........................................................... |
39 |
Engine Cooling Air Intake.......................................... |
40 |
Throttle Cable............................................................ |
40 |
Choke Cable ............................................................. |
40 |
Air Filter Maintenance............................................... |
41 |
Replacing Air Filter.......................................... |
41 |
Servicing Precleaner....................................... |
41 |
Servicing Paper Element................................. |
41 |
Replacing the Fuel Filter........................................... |
42 |
Tire Pressures........................................................... |
42 |
Parking Brake............................................................ |
43 |
V-belts....................................................................... |
43 |
Deck belt................................................................... |
44 |
Pump Belt.................................................................. |
45 |
Cutting Blades........................................................... |
45 |
Blade replacement.......................................... |
46 |
Adjusting the Mower Deck......................................... |
47 |
Leveling deck.................................................. |
47 |
Anti-scalp rollers.............................................. |
48 |
Cleaning and Washing.............................................. |
49 |
Caster Wheels........................................................... |
49 |
Hardware................................................................... |
49 |
LUBRICATION................................................................. |
50 |
Lubricating the Cables............................................... |
51 |
Front Wheel Mount.................................................... |
51 |
Front Wheel Bearings................................................ |
51 |
Deck spindle.............................................................. |
51 |
Engine Oil.................................................................. |
52 |
Engine Oil Filter............................................... |
52 |
Changing the Engine Oil................................. |
52 |
Engine Oil Levels............................................ |
53 |
Hydraulic Pump ........................................................ |
54 |
Fluid Change................................................... |
54 |
Purging Procedures......................................... |
54 |
TROUBLESHOOTING..................................................... |
55 |
STORAGE....................................................................... |
57 |
Storage...................................................................... |
57 |
Service...................................................................... |
57 |
schematics................................................................. |
58 |
TECHNICAL DATA........................................................... |
59 |
Accessories............................................................... |
63 |
Torque Specifications................................................ |
63 |
CONFORMITY CERTIFICATES...................................... |
65 |
SERVICE JOURNAL....................................................... |
66 |
After the First 5-8 Hours............................................ |
67 |
25-Hour Service........................................................ |
68 |
50-Hour Service........................................................ |
69 |
100-Hour Service...................................................... |
70 |
300-Hour Service...................................................... |
71 |
At Least Once Each Year.......................................... |
72 |
WARNING!
Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower.
Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WARNING!
Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Congratulations
Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.
This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance, etc.) by all who operate this machine is important for the safety of the operator and others. It can also considerably increase the life span of the machine and increase its resale value.
If you sell your machine, be sure to give the operator’s manual to the new owner.
The final chapter of this operator’s manual provides a Service Journal. Ensure that service and repair work are documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s resale value. Please contact your dealer for more information. Take the operator’s manual along when the machine is taken to your dealer for service.
In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving direction.
Continuous dedication to improve our products require that specifications and design are subject to change without notice.
Check applicable road traffic regulations before transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways.
Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and possible serious injury to the operator.
This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones, tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed.
Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense.
The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to maintain this machine.
Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail.
Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage.
English-5
INTRODUCTION
Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the certificate in the Service Journal in this operator’s manual.
When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional:
|
|
|
This Operator’s Manual belongs to the machine with |
Engine |
Transmission |
the manufacturing number: |
|
|
|
|
|
Manufacturing Number
The machine’s manufacturing number can be found on the printed plate affixed to the left in the engine compartment. Stated on the plate, from the top are:
•The machine’s type designation (I.D.).
•The manufacturer’s type number (Model).
•The machine’s serial number (Serial no.)
Please have the type designation and serial number available when ordering spare parts.
The engine’s manufacturing number is stamped on one of the valve covers. The plate states:
•The engine’s model.
•The engine’s type.
•Code
Please have these available when ordering spare parts.
The wheel motors and hydrostatic pumps have a barcode decal affixed at the rear.
English-6
These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.
WARNING!
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
IMPORTANT INFORMATION
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.
R N
Reverse Neutral Fast Slow Choke Fuel
P
Warning! |
Parking Brake |
CE conformity |
Warning! Rotating blades, |
Do not touch parts |
|
|
marking. Only for |
keep away from the |
|
|
|
European market |
discharge deck |
|
Battery acid is corrosive, explosive and flammable |
Do not stand here |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
Noise emissions to the surroundings in accordance with the European Union’s directive. The machine’s emission is stated in the chapter TECHNICAL DATA and on the decals.
Use protective glasses |
Use protective gloves |
Only machines for European |
market |
English-7
symbols and decals
Read |
Shut off engine and |
Keep a safe |
Use on slopes |
No passengers |
Operator’s |
remove key before |
distance from |
no greater |
|
Manual |
performing any |
the machine |
than 10° |
|
|
maintenance or repair work |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Whole body |
Severing of fingers |
Do not open or |
Careful backing up, |
|
Careful going |
||||||||
exposure to |
and toes |
remove safety |
watch for other |
forward, watch for |
|||||||||
thrown objects |
|
shields while |
|
people |
|
other people |
|||||||
|
|
engine is running |
|
|
|
|
|
|
|
|
|
|
|
Moving sharp blades under cover
English-8
These instructions are for your safety. Read them carefully.
WARNING!
This symbol means that important safety instructions need to be emphasized. It concerns your safety.
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
•Read, understand, and follow all instructions on the machine and in the manual before starting.
•Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
•Only allow responsible adults, who are familiar with the instructions, to operate the machine.
•Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.
•Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
•Never carry passengers. The machine is only intended for use by one person.
•Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
•Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.
•Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working
•Slow down before turning.
•Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.
•Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge chute.
8011-512 |
Read the operator’s manual before starting the machine
8011-513
Clear the area of objects before mowing
English-9
SAFETY
•Operate machine only in daylight or good artificial light.
•Do not operate the machine while under the influence of alcohol or drugs.
•Watch for traffic when operating near or crossing roadways.
•Use extra care when loading or unloading the machine into a trailer or truck.
•Always wear eye protection when operating machine.
•Data indicates that operators age 60 years and above are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.
•Follow the manufacturer’s recommendation for wheel weights or counterweights.
•Anyone who operates this machine must first read and understand this Operation Manual. Local laws may regulate the age of the user.
•Keep machine free of grass, leaves or other debris buildup which can touch hot exhaust / engine part and burn. Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.
8011-520 |
Never take passengers
WARNING!
Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
English-10
SAFETY
WARNING!
When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.
•Make sure that you have first aid equipment close at hand when using the machine.
•Never use the machine when barefoot.
• Always wear protective shoes or boots, preferably with steel toe caps.
• Always wear approved protective glasses or a full visor when assembling or driving.
•Always wear gloves when handling the blades.
• Never wear loose clothing that can get caught in moving parts.
•Use ear protectors to avoid damage to hearing.
Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
•Mow up and down slopes (10 degrees maximum), not across.
•Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
•Choose a low ground speed so that you will not have to stop while on the slope.
•Do not mow on wet grass. Tires may lose traction.
•Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.
•Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over.
•Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine.
8011-670a
Personal protective equipment
6003-004 |
Mow up and down, not side to side
WARNING!
Do not drive up or down hills with slopes greater than 10 degrees. And do not drive across any slopes.
English-11
SAFETY
•Do not use on steep slopes.
•Do not try to stabilize the machine by putting your foot on the ground.
•Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in.
Children
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity.
Never assume that children will remain where you last saw them.
•Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator.
•Be alert and turn machine off if a child enters the area.
•Before and while backing, look behind and down for small children.
•Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
•Never allow children to operate the machine.
•Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child.
English-12
8011-509 |
Be extra cautious when driving on slopes
8011-517 |
Never allow children to operate the machine
8011-518 |
Keep children away from work area
SAFETY
WARNING!
The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed.
To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
•Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
•Use only approved gasoline container.
•Never remove gas cap or add fuel with the engine running. Allow engine to cool at least two (2) minutes before refueling.
•Never fuel the machine indoors.
•Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliance.
•Before you begin refueling, minimize the risk of static electricity by touching a metal surface.
•Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from the vehicle when filling.
•Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.
•Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
•If fuel is spilled on clothing, change clothing immediately.
•Never overfill fuel tank. Replace gas cap and tighten securely.
•Do not start the engine near spilled fuel.
•Never use gasoline as a cleaning agent.
•If leaks arise in fuel system, engine must not be started until problem has been resolved.
•Check the fuel level before each use and leave space for the fuel to expand, as the heat from the engine and the sun may otherwise cause the fuel to expand and overflow.
8011-516 |
Never fill the fuel tank indoors
WARNING!
The engine and the exhaust system become very hot during operation.
There is risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling.
English-13
SAFETY
•Never operate machine in a closed area.
•Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
•Never tamper with safety devices. Check their proper operation regularly.
•Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage
and remove any fuel-soaked debris. Allow machine to cool before storing.
•If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting.
•Never make any adjustments or repairs with the engine running.
•Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts, when necessary.
•Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.
•Check brake operation frequently. Adjust and service as required.
•Maintain or replace safety and instruction labels, as necessary.
•Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
•Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
•Be very careful when handling battery acid. Acid on skin can cause serious corrosive burns. If you spill battery acid on your skin, rinse immediately with water.
•Acid in the eyes can cause blindness, contact a doctor immediately.
•Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks.
•The battery can explode and cause serious injury/damage.
8011-515 |
Never drive the machine in an enclosed space
Use protective glasses for maintenance work.
WARNING!
The battery contains lead and lead compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery.
English-14
SAFETY
•Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition.
•Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
•Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
•Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery.
WARNING!
Avoid electrical sparking and its consequences by the following routines:
•Use protective goggles.
•Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel.
•Never work with the starter circuit if there is spilled fuel.
•Disconnect the chassis cable from the battery first and reconnect it last.
•Do not make a bridge short circuit across the starter relay to run the starter.
•Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas.
•Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.
•Never make adjustments with the engine running.
•The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.
6003-009 |
Do not smoke when performing maintenance on the battery. The battery can explode and cause serious injury/damage.
8009-728 |
Risk of sparking
English-15
SAFETY
•The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them.
•Check the parking brake’s functionality regularly. Adjust and service as necessary.
•The mulch blades should only be used in familiar areas when higher quality mowing is desired.
•Reduce the risk of fire by removing grass, leaves, and other debris that may have accumulated on the machine. Allow the machine to cool before putting it in storage.
•Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.
•The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.
•Use an approved trailer to transport the machine. Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting.
•Do not operate this machine on public roadways.
•Check and abide by local traffic regulations before transporting the machine on any road.
•Do not tow this machine, it may cause damage to the drive system.
•Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator.
•Load the unit onto truck or trailer by driving up ramps of suitable strength using a slow speed. Do not lift! The machine is not intended to be lifted by hand.
8011-514 |
Regularly clean deck
WARNING!
Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately.
IMPORTANT INFORMATION
The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the
transport vehicle to avoid tipping it over.
English-16
SAFETY
The ROPS increases the basic weight of the unit by 42 lbs/19 kg. The ROPS is an accessory.
•Do not use ROPS as a lifting, attaching or anchoring point.
•Do not use ROPS for wrecking or towing.
•Do not exceed Max GVW: 2822 lbs/1283 kg.
•Read machine operator´s manual before each use.
•Securely fasten your seat belt if the unit has a ROPS.
•Where possible, avoid operating the unit near ditches, embankments and holes.
•Reduce speed when turning, crossing slopes and on rough, slick or muddy surfaces.
•Stay off slopes too steep for safe operation.
•Watch where you are going, especially at row ends, on roads and around trees.
•Do not permit others to ride.
•Operate the mower smoothly - no jerky turns, starts or stops.
•When mower is stopped, set brakes securely and use park brake.
•If any part of ROPS is damaged, the entire ROPS must be replaced.
•Check all bolts including seat belt for correct torque before each use.
•Check ROPS structure for damage before each use.
•ROPS bar is NOT intended for use in sub zero temperatures.
WARNING!
The rollover protection system's capabilities may be impaired by damage if the mower is overturned or if alteration to the ROPS occurs. If these conditions
take place, the total structure MUST be replaced.
WARNING!
This mower is equipped with an internal combustion engine and should not
be used on or near any unimproved forested, bush covered or grassy lands unless the engine's system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
English-17
This operator’s manual describes the Husqvarna
Zero Turn Rider. The rider is fitted with a Kohler fourstroke overhead valve engine developing 25-27 horse power*.
Transmission from the engine is made via a belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed.
9 |
8 |
|
7 |
13 |
2 |
|
|
|
|
|
1 |
|
|
|
|
|
10 |
|
|
|
|
|
11 |
|
|
|
|
|
12 |
|
6 |
5 |
4 |
3 |
|
1. |
Motion control levers |
8. |
Fuel tank cap |
2. |
Parking brake |
9. |
Fuel shut off valve |
3. |
Throttle control |
10. |
Deck lift |
4. |
Blade switch |
11. |
Seat adjustment lever |
5. |
Ignition switch |
12. |
Hour meter |
6. |
Choke control |
13. |
Tracking knob |
7. |
Fuses |
|
|
*As rated by the engine manufacturer.
English-18
CONTROLS
The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about
a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.
When both controls are in the neutral position (N), the machine stands still.
By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver.
If the steering controls are in uneven positions when standing still or do not fit in the slots for moving the controls outward, they can be adjusted.
8011-789
Steering controls
WARNING!
The machine can turn very rapidly if one steering control is moved much further forward than the other.
1 |
|
2 |
3 |
4 |
|
|
8011-7912 |
1.Forward
2.Neutral
3.Neutral slot, Neutral lock
4.Reverse
Motion control lever, right side
English-19
CONTROLS
IMPORTANT INFORMATION
The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower.
The parking brake is found on the left of the machine. Pull the lever backward to activate the brake and forward to release it.
8061-010 |
Parking brake not activated
The throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the Mower Deck.
In order to increase or decrease the engine speed, the control is moved forward or back respectively.
Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs.
USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging.
8061-001 |
Throttle control
In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed.
English-20
8061-002 |
Blade switch
CONTROLS
The ignition key is placed on the control panel and is used to start and stop the engine.
The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.
For cold starts the control should be pulled out to its extent.
8061-003 |
Ignition switch
8061-004 |
Choke control
Fuses are located on the left hand side of the machine. They are accessed by tilting the seat forward. They are flat pin fuses of the same type used in automobiles.
There are two fuses with ratings and functions:
•20 A, Primary fuse.
•7.5 A, Mower deck coupling.
8011-420 |
Fuses |
English-21 |
CONTROLS
Read the safety instructions before refueling. The machine has one fuel tank, just behind the seat. The tank capacity is 5.7 gallons (22 liters).
Make sure the fuel cap is properly tightened and the cap gasket is not damaged.
The engine will run on a minimum of 85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel. Damage to engine and components may occur.
WARNING!
Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the safety instruction).
WARNING!
The engine and the exhaust system, become very hot during operation.
Risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling
WARNING!
Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to help insure good cold weather starting.
8011-625 |
Fuel tank
IMPORTANT INFORMATION
Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.
English-22
CONTROLS
The fuel shut off valve is located at the left rear of the seat. The valve is off when the handle tab is turned perpendicular to the fuel line.
8011-419 |
Fuel shut off valve in the CLOSED position.
10. Lifting Lever for the Mower Deck
The lifting lever is used to transfer the mower deck from the transport position into the preferred cutting height position.
To set the cutting height, pull out the detent ring and place it in the desired height’s corresponding hole.
To lower the deck from the transport position, press forward on the foot pedal while pulling back on the transport latch. This releases it from the locked position and allows it to ease down to the detent pin, setting the selected cutting height.
IMPORTANT INFORMATION
In order to obtain an even cutting height, it is important that the air pressure in the front tires is 15 psi and the rear tires is 10 psi.
IMPORTANT INFORMATION
Always use the high position to transport.
1 |
2 |
3 |
8061-007 |
1.Detent Pin
2.Transport latch
3.Foot Pedal
The mower deck’s lifting lever
English-23
CONTROLS
11. Seat Adjustment Lever
The seat can be adjusted lengthways. When making adjustments, the lever under the front edge of the seat is moved to the left (as seen by the driver in the seat), after which the seat can be moved backward or forward.
The hour meter displays the total operating time.
It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on
and shut off automatically. The hour meter cannot be manually reset.
8011-441 |
Lengthways adjustment
8011-441 |
Hour meter
If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 10 psi. (.7 bar) for the front tires and 15 psi (1 bar) for the rear tires. Tracking must be checked on a flat and level concrete or blacktop surface.
Rotating the tracking knob allows fine tuning adjustments so the machine tracks straight with the steering control levers in the full forward position.
Rotate the knob clockwise (as viewed from the operation position) to increase the speed on the left lever. Rotate counterclockwise to decrease speed.
English-24
8011-441 |
Lengthways adjustment