Fairchild Semiconductor NM24C08ULM8X, NM24C08UEM8, NM24C08UEM8X, NM24C08UEN, NM24C08UFEM8 Datasheet

1

www.fairchildsemi.com

NM24C08U/09U Rev. B.1

NM24C08U/NM24C09U – 8K-Bit

Ł Serial EEPROM 2-Wire Bus Interface

NM24C08U/NM24C09U
8K-Bit Serial EEPROM
2-Wire Bus Interface

General Description,

The NM24C08U/09U devices are 8K (8,192) bit serial interface
CMOS EEPROMs (Electrically Erasable Programmable Read­Only Memory). These devices fully conform to the Standard I2C™
2-wire protocol which uses Clock (SCL) and Data I/O (SDA) pins
to synchronously clock data between the "master" (for example a
microprocessor) and the "slave" (the EEPROM device). In addi­tion, the serial interface allows a minimal pin count packaging
designed to simplify PC board layout requirements and offers the
designer a variety of low voltage and low power options.

NM24C09U incorporates a hardware "Write Protect" feature, by
which, the upper half of the memory can be disabled against
programming by connecting the WP pin to VCC. This section of
memory then effectively becomes a ROM (Read-Only Memory)
and can no longer be programmed as long as WP pin is connected
to VCC.

Fairchild EEPROMs are designed and tested for applications requir­ing high endurance, high reliability and low power consumption for a
continuously reliable non-volatile solution for all markets.

Block Diagram

August 1999

Functions

■ I2C™ compatible interface
■ 8,192 bits organized as 1,024 x 8
■ Extended 2.7V – 5.5V operating voltage
■ 100 KHz or 400 KHz operation
■ Self timed programming cycle (6ms typical)
■ "Programming complete" indicated by ACK polling
■ NM24C09U: Memory "Upper Block" Write Protect pin

Features

■ The I2C™ interface allows the smallest I/O pincount of any

EEPROM interface

■ 16 byte page write mode to minimize total write time per byte
■ Typical 200µA active current (I

CCA

)

■ Typical 1µA standby current (ISB) for "L" devices and 0.1µA

standby current for "LZ" devices

■ Endurance: Up to 1,000,000 data changes
■ Data retention greater than 40 years

© 1999 Fairchild Semiconductor Corporation

H.V. GENERATION

TIMING &CONTROL

E2PROM

ARRAY

YDEC

DATA REGISTER

XDEC

CONTROL

LOGIC

WORD
ADDRESS
COUNTER

SLAVE ADDRESS

REGISTER &

COMPARATOR

START

STOP

LOGIC

CK

D

IN

R/W

SDA

SCL

V

SS

WP

V

CC

D

OUT

A2

DS800009-1

I2C™ is a registered trademark of Philips Electronics N.V.

2

www.fairchildsemi.com

NM24C08U/09U Rev. B.1

NM24C08U/NM24C09U – 8K-Bit

Ł Serial EEPROM 2-Wire Bus Interface

NC
NC

A2

V

SS

V

CC

NC
SCL
SDA

8
7
6
5

1
2
3
4

Connection Diagrams

Dual-In-Line Package (N), SO Package (M8), and TSSOP Package (MT8)

Top View

See Package Number N08E, M08A, and MTC08

Pin Names

A2 Device Address Input

V

SS

Ground
SDA Serial Data I/O
SCL Serial Clock Input

NC No Connection
V

CC

Power Supply

Pin Names

NC No Connection

A2 Device Address Input

V

SS

Ground
SDA Serial Data I/O
SCL Serial Clock input

WP Write Protect
V

CC

Power Supply

NC
NC

A2

V

SS

V

CC

WP
SCL
SDA

8
7
6
5

1
2
3
4

NM24C08U

NM24C09U

DS800009-2

DS800009-5

Dual-In-Line Package (N), SO Package (M8), and TSSOP Package (MT8)

Top View

See Package Number N08E, M08A, and MTC08

3

www.fairchildsemi.com

NM24C08U/09U Rev. B.1

NM24C08U/NM24C09U – 8K-Bit

Ł Serial EEPROM 2-Wire Bus Interface

Ordering Information
NM 24 C XX U F LZ E XX Letter Description

Package N 8-pin DIP

M8 8-pin SOIC
MT8 8-pin TSSOP

Temp. Range None 0 to 70°C

V -40 to +125°C
E -40 to +85°C

Voltage Operating Range Blank 4.5V to 5.5V

L 2.7V to 5.5V
LZ 2.7V to 5.5V and

<1µA Standby Current

SCL Clock Frequency Blank 100KHz

F 400KHz

Ultralite CS100UL Process

Density 08 8K

09 8K with Write Protect

C CMOS Technology
W Total Array Write Protect

Interface 24 IIC

NM Fairchild Non-Volatile

Memory

4

www.fairchildsemi.com

NM24C08U/09U Rev. B.1

NM24C08U/NM24C09U – 8K-Bit

Ł Serial EEPROM 2-Wire Bus Interface

Product Specifications
Absolute Maximum Ratings

Ambient Storage Temperature –65°C to +150°C
All Input or Output Voltages

with Respect to Ground 6.5V to –0.3V

Lead Temperature

(Soldering, 10 seconds) +300°C

ESD Rating 2000V min.

Operating Conditions

Ambient Operating Temperature

NM24C08U/09U 0°C to +70°C
NM24C08UE/09UE -40°C to +85°C
NM24C08UV/09UV -40°C to +125°C

Positive Power Supply

NM24C08U/09U 4.5V to 5.5V
NM24C08UL/09UL 2.7V to 5.5V
NM24C08ULZ/09ULZ 2.7V to 5.5V

Standard VCC (4.5V to 5.5V) DC Electrical Characteristics

Symbol Parameter Test Conditions Limits Units

Min Typ Max

(Note 1)

I

CCA

Active Power Supply Current f

SCL

= 400 KHz 0.2 1.0 mA

f

SCL

= 100 KHz

I

SB

Standby Current VIN = GND or V

CC

10 50 µA

I

LI

Input Leakage Current VIN = GND to V

CC

0.1 1 µA

I

LO

Output Leakage Current V

OUT

= GND to V

CC

0.1 1 µA

V

IL

Input Low Voltage –0.3 VCC x 0.3 V

V

IH

Input High Voltage VCC x 0.7 VCC + 0.5 V

V

OL

Output Low Voltage I

OL

= 3 mA 0.4 V

Low VCC (2.7V to 5.5V) DC Electrical Characteristics

Symbol Parameter Test Conditions Limits Units

Min Typ Max

(Note 1)

I

CCA

Active Power Supply Current f

SCL

= 400 KHz 0.2 1.0 mA

f

SCL

= 100 KHz

I

SB

Standby Current VIN = GND VCC = 2.7V - 4.5V 1 10 µA

or V

CC

VCC = 2.7V - 4.5V 0.1 1 µA
VCC = 4.5V - 5.5V 10 50 µA

I

LI

Input Leakage Current VIN = GND to V

CC

0.1 1 µA

I

LO

Output Leakage Current V

OUT

= GND to V

CC

0.1 1 µA

V

IL

Input Low Voltage –0.3 V

CC

x 0.3 V

V

IH

Input High Voltage VCC x 0.7 VCC + 0.5 V

V

OL

Output Low Voltage IOL = 3 mA 0.4 V

Capacitance T

A

= +25°C, f = 100/400 KHz, VCC = 5V (Note 2)

Symbol Test Conditions Max Units

C

I/O

Input/Output Capacitance (SDA) V

I/O

= 0V 8 pF

C

IN

Input Capacitance (A0, A1, A2, SCL) VIN = 0V 6 pF

Note 1: Typical values are TA = 25°C and nominal supply voltage (5V).
Note 2: This parameter is periodically sampled and not 100% tested.