Epson PowerLite 5300, PowerLite 7200, PowerLite 7300 User Manual

EPSON PowerLite®

5300/7200/7300 User’s Guide

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions.

SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION.

EPSON and PowerLite are registered trademarks of SEIKO EPSON CORPORATION.

SoundAdvice is a service mark and FaxAdvice is a trademark of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.

Copyright © 1998 by Epson America, Inc.	CPD-7925
Torrance, California, USA	7541655
	12/98

Important Information About Your Projector

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Remote Control Information

You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions:

There is an object between the remote control IR emitter and the IR receiver on the projector.

Ambient light is too bright.

Certain types of fluorescent lighting are used.

A strong light source shines into the IR receiver.

Other equipment that emits infrared energy, such as a radiant room heater, is in the room.

These conditions commonly cause problems for most infrared-controlled equipment. Try the following:

The remote control unit’s batteries may be low on power; replace them.

Dim the ambient lighting and/or turn off any fluorescent lights.

Close any window coverings and/or move the projector out of direct sunlight.

Turn off other equipment that emits infrared energy.

If the remote control still does not work properly, remember you can always control your computer-based presentation directly from the computer, even in an environment containing one of the conditions listed above.

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.

Contents

Introduction	1
Getting the Most Out of Your Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 3
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 4
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 5
Where to Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 6
Electronic Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 6
Automated Telephone Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 7
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 8
1 Setting Up the Projector	11
Unpacking the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	12
Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	14
Before You Connect the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	15
Installing the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	16

i

Connecting to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	.18
Connecting to a PC Desktop Computer . . . . . . . . . . . . . . . . . . . . . . . . . . .	.19
Connecting to a PC Laptop Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	26
Connecting to a Desktop Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	31
Connecting to a PowerBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	40
Connecting to a High-End Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . .	49
Connecting to a Video Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	49
Connecting to an External Speaker or PA System . . . . . . . . . . . . . . . . . . . . . . . . .	53
Turning the Equipment On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	54
Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	55
2 Using the Projector	57
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	58
Calculating Image Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . .	60
Focusing and Positioning the Screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	63
Resize Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	65
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	65
Controlling the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	66
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	67
Using the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	70
Projector Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	72
3 Using the Projector Menus	75
Accessing the Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	76
Changing a Menu Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	78
Video Menu (Image Source = Computer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	80
Video Menu (Image Source = Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	82
Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	83
Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	85

ii

Custom Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

About Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Reset All Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

4 Using the ELP Link III Software	91
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 92
Connecting Needed Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 92
Installing the Software for Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 92
Installing the Software for a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 94
Launching the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 94
Launching the Software from Windows . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 95
Launching the Software on a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 96
Using the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 96
Customizing the Remote Control Effects Buttons . . . . . . . . . . . . . . . . . . .	. . 96
Controlling Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 103
5 Maintenance	117
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 118
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 118
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 119
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 120
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 123
6 Troubleshooting	125
Problems with the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 126
Problems with the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	129
Problems with the Image or Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	130

iii

7 Technical Specifications	133
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	.137
Glossary	139
Index	141

iv

Introduction

Your PowerLite® projector is a brilliant, lightweight, portable projector that allows you to project full-color images and video onto a large screen for presentations. You can connect it simultaneously to three image sources: two computers or workstation sources, plus one video source, such as a VCR or camcorder. You can also connect audio for each image source.

Images are displayed in full color (16,770,000 colors) at an SVGA resolution of 800 × 600 pixels on the PowerLite 5300, or an XGA resolution of 1024 × 768 pixels on the PowerLite 7200 and PowerLite 7300. The projector supports a wide variety of video inputs, from VGA to SXGA with resolutions up to 1280 × 1024. It produces bright images that can be easily seen in rooms light enough to take notes.

Your projector’s two speakers employ a built-in 3D Sound System for rich, powerful audio output. You can even connect an external speaker when further amplification is required.

1

For your presentations, you can select front, rear, or ceiling projection. This provides maximum flexibility in choosing the best display method for each environment.

You control your projector through a hand-held remote control unit, with menus provided for image source switching and image adjustment. The remote control can also act as a wireless mouse to control operations on your computer screen during presentations. Additionally, you can install the projector’s ELP Link III software to control the projector’s settings from your computer and enhance your presentations with special effects.

Your projector features a new patented SizeWise™ chip for support of VGA, SVGA, XGA, and SXGA output. No matter what type of computer output is used, the result is a full-size video image of outstanding clarity.

The projector supports a wide range of computers and workstations: IBM® compatible PCs and laptops, Apple® Macintosh,® Power Macintosh,™ and PowerBook™ computers, and workstations such as the Sun® SPARCstation™ (The PowerLite 5300 is not recommended for use with high-end workstations). The video source can be NTSC, PAL, or SECAM. The projector automatically senses the video format, which can be composite video, S-Video, or component video. See Chapter 7 for details on supported computers and video formats.

2 Introduction

Getting the Most Out of Your Projector

Your projector comes with a full set of features that enable you to control the settings for the image display, video, and audio. To get the most out of the projector, read this section for a quick summary of the important features.

Remote Control

The buttons on the remote control enable you to turn the projector on and off, and provide direct access to blank, freeze, volume, mute, and image source switching. Use the remote control buttons to access custom functions (with the ELP Link III software) and the projector’s menu system. You can even use the remote control to control your computer in place of your computer’s mouse.

Sleep Mode

Sleep mode conserves electricity by automatically turning off the lamp after the projector has not been used for 30 minutes. In sleep mode, the projector remains on but the lamp is turned off, conserving electricity, cooling the projector, and extending the life of the lamp.

Control Panel

The control panel buttons on the projector duplicate the remote control buttons.

Getting the Most Out of Your Projector

3

Optional Accessories

To enhance your use of the projector, EPSON provides the following:

●Customized carrying cases for the projector and its cables:

	Hard Shell Carrying Case	ELPKS12
	Soft Shell Carrying Case	ELPKS10
●	Replacement lamp and air filter	ELPLP05
●	Long throw zoom lens	ELPLL01

●Communication kit cable set and computer cable so you can connect your projector to a second computer. There is also a Mac® adapter set so you can connect to a second Macintosh. You may also need the VGA-13W3 video cable if you’re connecting the projector to a high-end workstation.

	ELP communication cable set	ELPKC04
	Computer video cable	ELPKC02
	Mac adapter set	ELPAP01
	VGA-13W3 video cable	ELPKC06
	VGA-5BNC video cable	ELPKC07
●	Portable projection screen	ELPSC06
● Remote control receiver module		ELPST02
●	Mediaphile™ PAS	ELPPAS1
	(personal audio system)

You can purchase these accessories from your dealer or by calling EPSON Accessories at [phone]; or visit our web site at www.epsonsupplies.com (U.S. sales only). In Canada, please call [phone] for dealer referral.

4 Introduction

About This Guide

This guide describes how to set up and use the EPSON PowerLite 5300, PowerLite 7200, and PowerLite 7300 projectors. The instructions pertain to all these models, except where otherwise noted.

Chapter 1, “Setting Up the Projector,” provides step-by-step instructions on how to set up your projector; connect it to your computer, video source, or other optional equipment; and turn it on.

Chapter 2, “Using the Projector,” explains how to position the projector relative to the screen, focus and position the screen image, control the projector using the remote control and the control panel, and monitor the projector’s operating status.

Chapter 3, “Using the Projector Menus,” describes how to use the projector’s built-in menus to adjust the color and image settings, change the display of the projected image, and modify audio settings such as bass and treble.

Chapter 4, “Using the ELP Link III Software,” explains how to use the ELP Link III software to control the projector settings from the computer and use the special effects functions.

Chapter 5, “Maintenance,” covers basic procedures for maintaining your projector in good working order and gives guidelines for transporting it.

Chapter 6, “Troubleshooting,” describes how to interpret your projector’s warning lights and gives helpful information for avoiding errors, optimizing image quality, and solving problems.

About This Guide

5

Chapter 7, “Technical Specifications,” lists the technical specifications for the projector.

A Glossary and Index are provided at the end of the manual.

Where to Get Help

If you are having trouble setting up or running your projector, first see Chapter 6, “Troubleshooting.” If you cannot resolve the problem, EPSON provides technical assistance through electronic support services and automated telephone services 24 hours a day. The following tables list the contact information.

Electronic Support Services

Service	Access
World Wide Web	From the Internet, you can reach EPSON’s Home Page at
	http://www.epson.com.
EPSON Internet FTP Site	If you have Internet FTP capability, use your Web
	browser (or other software for FTP downloading) to log
	onto ftp.epson.com with the user name anonymous
	and your e-mail address as the password.
EPSON Download Service	You can call the EPSON Download Service at
	[phone]. Set your communications software
	to 8 data bits, 1 stop bit, no parity. Modem speed can be
	up to 28.8 Kbps.
EPSON Forum on	Members of CompuServe can type GO EPSON at the
CompuServe®	menu prompt to reach the Epson America Forum.
	For a free introductory CompuServe membership, call
	[phone] and ask for representative #529.

6 Introduction

Automated Telephone Services

Service	Access
EPSON SoundAdviceSM	For pre-recorded answers to commonly asked questions
	about EPSON products 24 hours a day, seven days a
	week, call [phone].
EPSON FaxAdvice™	Access EPSON’s technical information library by calling
	[phone]. You must provide a return fax number to
	use this service.
EPSON Referral Service	For the location of your nearest Authorized EPSON
	Reseller or Customer Care Center, call [phone].

When you need support, follow the calling instructions on the back of the EPSON Private Line Technical Support card included with the projector. Technical support is also available by calling

[phone] between 6 AM and 6 PM, Pacific Time, Monday through Friday. Toll or long distance charges may apply.

Before you call, please have the following information ready:

●Product name

●Product serial number

●Personal identification number (PIN) for EPSON Private Line Technical Support

●Computer configuration

●Description of the problem

Where to Get Help

7

You can purchase accessories from EPSON Accessories at

[phone], or visit our web site at www.epsonsupplies.com (U.S. sales only). In Canada, please call [phone] for dealer referral.

Safety Instructions

Follow these safety instructions when setting up and using the projector:

1.Do not place the projector on an unstable cart, stand, or table.

2.Do not use the projector near water or sources of heat.

3.Use attachments only as recommended.

4.Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.

5.Place the projector near a wall outlet where the plug can be easily unplugged.

6.Insert the projector’s three-wire grounding-type plug into a properly grounded outlet. If you have a two-prong outlet, contact an electrician to replace it. Do not hold the plug with wet hands.

7.Take the following precautions for the plug. Failure to comply with these precautions could result in sparks or fire.

●Do not insert the plug into an outlet with dust present.

●Insert the plug firmly into the outlet.

8 Introduction

8.Do not overload wall outlets, extension cords, or integral convenience receptacles. This can cause fire or electric shock.

9.Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug.

10.Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.

11.Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or in a closed-in cabinet unless proper ventilation is provided.

12.Never push objects of any kind through cabinet slots. Never spill liquid of any kind into the projector.

13.Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.

14.Unplug the projector during lightning storms or when it will not be used for extended periods.

15.Do not place the projector and remote control on top of heat-producing equipment or in a heated place, such as a car.

Safety Instructions

9

16.Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:

●When the power cord or plug is damaged or frayed

●If liquid has been spilled into the projector, or if it has been exposed to rain or water

●If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service

●If it has been dropped or the housing has been damaged.

10 Introduction

1

Setting Up the Projector

This chapter describes how to unpack your projector, connect it to your other equipment, and turn everything on. The projector must be connected to a computer or a video source such as a VCR, camcorder, or laser disc player before it can project any images. You may also want to set up the projector for one or more of the following:

●Connect the mouse cable to use the remote control as a wireless mouse. Except for some laptops, this disables your computer’s mouse. If you are also viewing the display on your monitor, you use the remote control’s pointer to control the screen cursor.

●Provide audio for one or both image sources. The audio source can be the computer, video source, or another device such as a stereo.

●Connect to an external speaker or PA system to amplify the audio.

11

Unpacking the Projector

When you unpack the projector, make sure you have all these components:

●	Projector
●	Remote control
●	2 AA batteries
●	Power cord
●	Projector video cable
●	Audio cable
●	Audio/video (A/V) cable

12	1 • Setting Up the Projector

●Macintosh adapter set:

Macintosh desktop adapter

	Macintosh monitor adapter
●	Main cable (for connecting a mouse cable to
	use the remote as a wireless mouse and/or a
	serial cable to use the ELP Link III software)
●	PS/2® mouse cable (for the PC)
●	Serial mouse cable (for the PC)
●	Mac mouse cable (for the Macintosh)
●	PC serial cable
●	Macintosh serial cable
●	Projector Software CD ROM

Unpacking the Projector

13

You will not need all these components; your configuration will determine which ones you need.

Save all packaging in case you need to ship the projector in the future. Always transport the projector in its original packaging (or the equivalent), or use a carrying case if you are carrying the projector by hand. (See page 123 for instructions.)

Additional Components

Depending on how you plan to use the projector, you may need additional components:

●To receive an S-Video signal, you need an S-Video cable. (One is usually provided with your video device.) A separate cable is required for each video source.

●

●

To connect a second computer, you need a computer video and audio cable.

To connect the projector to a Macintosh PowerBook, you need a video-out cable. (One is provided by—or can be purchased from—Apple for all new PowerBooks that have video-out capability.) If your PowerBook does not include one, see your Macintosh dealer.

●To connect the projector to an external sound system, you need an RCA-to-3.5 mm stereo audio cable. You can obtain one from your computer dealer.

●To connect the mouse cable to your computer, you may require a special connector, cable, or other components. You can obtain these items from your computer dealer.

14	1 • Setting Up the Projector

Note: You can connect a Kensington MicroSaver® anti-theft device in the hole on the projector’s right side. Contact your computer dealer.

Before You Connect the Projector

Before you start connecting the projector to your equipment, decide where you will want to place your projector and computer or video source. The distance between the projector and the screen determines the actual image size. Place the projector somewhere between 4 and 54.7 feet (1.2 and 16.7 meters) away from the screen; use the general guidelines in the table below to determine the proper distance. (For more precise calculations, see “Positioning the Projector” on page 58.)

Caution: Do not hold or lift the projector by the lens. This can damage the lens.

	Horizontal distance from projector to screen
Image size (diagonal)	Minimum	Maximum
200 inches (5.1 m)	324.1 inches (8.2 m)	436.5 inches (11.1 m)
100 inches (2.54 m)	160.8 inches (4.1 m)	217.1 inches (5.5 m)
80 inches (2.03 m)	128.1 inches (3.3 m)	173.1 inches (4.4 m)
60 inches (1.52 m)	95.5 inches (2.4 m)	129.2 inches (3.3 m)
40 inches (1.02 m)	62.8 inches (1.6 m)	85.3 inches (2.2 m)
30 inches (0.76 m)	46.5 inches (1.2 m)	63.3 inches (1.6 m)
23 inches (0.58 m)	35.1 inches (0.9 m)	48.0 inches (1.2 m)

Before You Connect the Projector

15

Be sure to place the projector on a sturdy, level surface within five feet of the computer or video source.

Installing the Remote Control Batteries

You can use the remote control as a wireless mouse instead of your computer’s mouse to control your presentation. You can also use it to control the projector menus and use the Effects buttons.

Follow these steps to install the batteries in the remote control:

1. Slide off the battery compartment cover.

16	1 • Setting Up the Projector

2.Insert the two AA batteries included with the projector. Make sure the polarity of the batteries is correct.

3. Replace the battery compartment cover.

When replacing batteries, take the following precautions:

●Do not mix old and new batteries.

●Replace batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.

●Remove batteries if you will not be using the projector for a long period of time.

Before You Connect the Projector

17

Connecting to a Computer

You can connect the projector to any computer capable of producing standard VGA, Super VGA, XGA, or Super XGA output, such as:

●IBM compatible desktop PCs

●IBM compatible laptop PCs

●Apple Macintosh desktop computers, including Macintosh Quadra,® Macintosh Centris,® and Power Macintosh

●Any Apple PowerBook with video-out capability

●(PowerLite 7200 and 7300 only) Most high-end workstations from Sun, Silicon Graphics,® IBM, and Hewlett-Packard®. (You may need an adapter cable to connect to a high-end workstation; see page 49.)

See the section that applies to your computer. Make sure both the computer and projector are turned off before you start.

When you have finished connecting all your components, go to page 54 to turn on the projector and equipment.

18	1 • Setting Up the Projector

The illustration below identifies all the interface ports on the back of the projector; you may want to refer to this as you connect your computer or other equipment to the projector.

Audio Out	Audio 2	Audio 1
IR Repeater
		Mouse/Com 2
		Mouse/Com 1
		Computer 2
		Computer 1
		BNC HD/Sync VD
Power Inlet Computer Out	S-Video	Composite Video
R/R-Y G/Y G Sync B/B-Y

Connecting to a PC Desktop Computer

To connect the projector to your PC desktop computer, you need to:

●Connect the projector video cable and computer monitor cable

●Connect the mouse and/or serial cable (if you want to use the remote control as a mouse or use the ELP Link III software)

●Connect the audio cable (if you’ll be projecting with audio)

Connecting to a Computer

19

Follow the steps in each section for the cables you need to connect. Before beginning, turn off the projector and computer if they are on.

Note: Computer configurations vary. See your computer manual for the location of the ports needed to connect your projector.

Connecting the Video and Monitor Cables

First connect the projector video cable and computer monitor cable. Refer to this illustration while following the steps below.

Computer 1 port

projector video cable

Computer

monitor cable

Out port

20	1 • Setting Up the Projector

1.If you will be viewing the video on your computer monitor as well as the projector screen, disconnect the monitor cable from the video port on the back of your computer. Then connect the monitor cable to the projector’s Computer Out port, as shown below. (This is useful when you need to view the video output but the projection screen is behind you.)

2.Connect one end of the projector video cable to the projector’s Computer 1 port. (Use the Computer 2 port if you are connecting a second computer.)

	Connecting to a Computer	21

3.Connect the other end of the projector video cable to the computer’s video port.

4.Tighten the screws on all connectors.

Connecting the Mouse and Serial Cables

If you want to use the remote control as a mouse or use the ELP Link III software, you need to connect the main cable. It provides connectors for:

●The PS/2 mouse cable (to use the remote control as a mouse)

●The serial cable (to use the ELP Link III software and the Effects buttons on the remote control)

Refer to this illustration while following the steps below.

PS/2 mouse cable

Mouse/Com 1 port

9-pin serial cable

main cable

22	1 • Setting Up the Projector