|
|
Start Here |
|
|
Easy Setup Instructions |
|
|
|
|
Unpack the Printer |
• Please confi rm bundled thing by the illustration printed on the fl apped lid of the packing box. |
|
||
|
• A USB cable is necessary to connect the printer with your computer. |
|
|
||
|
|
|
QT5-0755-V01
1 Prepare the printer
aPlace the printer on a fl at and horizonal surface, and do not place any objects in front of the printer. Open the Paper Feed Tray and fold it in half.
Place fi nger here to open the Paper Feed Tray and fold it in half.
Paper Feed Tray
The Paper Output Tray will open
automatically.
Caution
Before turning on the printer, remove all of the shipping tapes.
bConnect the power cord to the AC Adapter, and then plug the AC Adapter into the printer. Connect the other end of the power cord to a power outlet and then press the ON/OFF button.
Important
If the Alarm lamp is lit orange and an error message is displayed, see “Error Message Is Displayed on the LCD” in the Photo Printing Guide.
cUse the { or } button or the Easy-Scroll Wheel on the Operation Panel to select the language for the LCD, then press the OK button.
Easy-Scroll Wheel
Important
If you selected the wrong language by mistake, press the Back button to select again.
dSlide the Lock Switch to the right, and then lift the Printer Cover. The cover will be locked if it is fully lifted.
2 Install the Print Head
aUnlock the Print Head Lock Lever by gently squeezing the tabs on both ends inward, and then raise the Print Head Lock Lever until it stops.
Print Head Lock Lever
bRemove the Print Head from its package.
Important
There might be some transparent or light blue ink on the inside of the bag the Print Head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.
cRemove the orange protective cap from the Print Head and discard it.
Protective Cap
Print Head Nozzles
Electrical Contacts
Important
Do not touch the Print Head nozzles and the electrical contacts.
dInsert the Print Head.
Align the mark on the Print Head and the mark on the printer.
eLower the Print Head Lock Lever carefully by pressing down the tabs on both ends until it clicks into place.
a
Click
b
Click
3 Install the ink tank
aRemove the orange protective cap and discard it.
Protective Cap
Ink Ports
Electrical Contacts
Important
Do not touch the electrical contacts and the ink ports.
bInsert the ink tank at a slant.
Align the mark ▲ on the ink tank and the mark ▼ on the printer.
cPress the mark on the ink tank until it clicks into place and then its lamp lights red.
Important
If the lamp does not light red after it is inserted, repeat steps 2 and 3.
dOpen the Printer Cover slightly, pull the Lock Lever to unlock, and then close the Printer Cover.
Lock Lever
Important
Once you have installed the ink tank, wait for about 90 seconds until the printer has stopped making operating noises, before proceeding.
Note
An error message will be displayed on the LCD if the lock lever is not set properly or the ink tank is not installed properly. Open the Printer Cover and make sure that the lock lever is set properly or ink tank is installed properly.
4 Align the Print Head
aLoad two sheets of the supplied 4” x 6” paper into the Auto Sheet Feeder with the whiter side facing front. Align the paper with the right side of the Auto Sheet Feeder, then slide the Paper Guide toward the left edge of the paper.
Paper Guide
Align the right side.
Auto Sheet Feeder
bWhen the message requesting head alignment is displayed on the LCD, press the OK button.
The pattern is printed and the Print Head is aligned automatically.
Note
•The pattern is printed in black and blue.
•Print Head alignment will take about 3 minutes to complete. Do not start another operation here.
•If the Auto Head alignment cannot be executed correctly and a message is displayed on the LCD, please refer to “Error Message Is Displayed on the LCD” in the Photo Printing Guide.
Hardware setup and Print Head alignment is complete.
If you are connecting the printer to a computer, please see the back side of this sheet for Software Installation Instructions.
Important
Be sure to Lock the Print Head Lever until it “clicks” into place.