Loading...
DIVAR IP 3000
DIP-3040-00N, DIP-3042-2HD, DIP-3042-4HD
en Quick Installation Guide
DIVAR IP 3000 Table of Contents | en 3
Table of Contents
1 |
Safety precautions |
4 |
1.1 |
General safety precautions |
4 |
1.2 |
Electrical safety precautions |
6 |
1.3 |
ESD precautions |
8 |
1.4 |
Operating precautions |
9 |
2 |
|
|
System overview |
10 |
|
2.1 |
Device views |
11 |
2.2 |
LED description - front panel |
13 |
2.3 |
LAN port LED description - rear panel |
14 |
3 |
|
|
System setup - first steps |
16 |
|
3.1 |
Introduction |
16 |
3.2 |
Setup instruction |
16 |
3.3 |
Starting the application |
17 |
3.4 |
Using Bosch VMS Config Wizard |
19 |
3.5 |
Adding additional licenses |
20 |
3.6 |
Using Bosch VMS Operator Client |
21 |
4 |
|
|
Additional Documentation and client software |
23 |
|
5 |
End-user license agreement (EULA) |
24 |
Bosch Sicherheitssystem GmbH |
2014.11 | V6 | DOC |
4 |
en | Safety precautions |
DIVAR IP 3000 |
|
|
|
1 Safety precautions
Observe the safety precautions in this chapter.
1.1General safety precautions
Follow these rules to ensure general safety:
–Keep the area around the system clean and free of clutter.
–Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won't accidentally be stepped on.
–While working on the system, do not wear loose clothing such as neckties and unbuttoned shirt sleeves, which can come into contact with electrical circuits or be pulled into a cooling fan.
–Remove any jewelry or metal objects from your body, which are excellent metal conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present.
Warning!
Interruption of mains supply:
Voltage is applied as soon as the mains plug is inserted into the
!However, for devices with a mains switch, the device is only ready for operation when the mains switch (ON/OFF) is in the
ON position. When the mains plug is pulled out of the socket, the supply of power to the device is completely interrupted.mains socket.
2014.11 | V6 | DOC |
Bosch Sicherheitssystem GmbH |
|
DIVAR IP 3000 |
Safety precautions | en |
5 |
|
|
|
Warning!
Removing the housing:
To avoid electric shock, the housing must only be removed by qualified service personnel.
!Before removing the housing, the plug must always be removed from the mains socket and remain disconnected while the
housing is removed. Servicing must only be carried out by qualified service personnel. The user must not carry out any repairs.
Warning!
Power cable and AC adapter:
When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any
!other cables and adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables (that have UL/CSA shown on the code) for any other electrical devices.
Warning!
Lithium battery:
Batteries that have been inserted wrongly can cause an explosion. Always replace empty batteries with batteries of the same type or a similar type recommended by the manufacturer.
!Handle used batteries carefully. Do not damage the battery in any way. A damaged battery may release hazardous materials into the environment.
Dispose of empty batteries according to the manufacturer's instructions.
Warning!
Handling of lead solder materials used in this product may
!expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.
Bosch Sicherheitssystem GmbH |
2014.11 | V6 | DOC |
6 |
en | Safety precautions |
DIVAR IP 3000 |
|
|
|
Notice!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried out correctly. When handling electrostatically sensitive printed circuits,
grounded anti-static wrist bands must be worn and the ESD safety precautions observed.
Notice!
Installation should only be carried out by qualified customer service personnel in accordance with the applicable electrical regulations.
Disposal
Your Bosch product has been developed and manufactured using high-quality materials and components that can be reused.
This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of separately from household waste.
In the EU, separate collecting systems are already in place for used electrical and electronic products. Please dispose of these devices at your local communal waste collection point or at a recycling center.
1.2Electrical safety precautions
Basic electrical safety precautions should be followed to protect you from harm and the system from damage:
–Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet. If an electrical accident occurs, you can then quickly remove power from the system.
2014.11 | V6 | DOC |
Bosch Sicherheitssystem GmbH |
|
DIVAR IP 3000 |
Safety precautions | en |
7 |
|
|
|
–Do not work alone when working with high voltage components.
–Power should always be disconnected from the system when removing or installing main system components, such as the motherboard or memory modules. When disconnecting power, you should first turn off the system and then unplug the power cords from all the power supply modules in the system.
–When working around exposed electrical circuits, another person who is familiar with the power-off controls should be nearby to switch off the power if necessary.
–Use only one hand when working with powered-on electrical equipment. This is to avoid making a complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which can easily damage any electrical components or circuit boards they come into contact with.
–The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets. The unit has more than one power supply cord. Disconnect both power supply cords before servicing to avoid electrical shock.
–Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature Coefficient) fuses on the mainboard must be replaced by trained service technicians only. The new fuse must be the same or equivalent as the one replaced. Contact technical support for details and support.
Caution!
Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside down, which will reverse its
!polarities. This battery must be replaced only with the same or an equivalent type recommended by the manufacturer
(CR2032). Dispose of used batteries according to the manufacturer's instructions.
Bosch Sicherheitssystem GmbH |
2014.11 | V6 | DOC |
8 |
en | Safety precautions |
DIVAR IP 3000 |
|
|
|
1.3ESD precautions
Electrostatic Discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic components and printed circuit boards. The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD:
–Do not use mats designed to decrease electrostatic discharge as protection from electrical shock. Instead, use rubber mats that have been specifically designed as electrical insulators.
–Use a grounded wrist strap designed to prevent static discharge.
–Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready for use.
–Touch a grounded metal object before removing the board from the antistatic bag.
–Do not let components or printed circuit boards come into contact with your clothing, which may retain a charge even if you are wearing a wrist strap.
–Handle a board by its edges only. Do not touch its components, peripheral chips, memory modules or contacts.
–When handling chips or modules, avoid touching their pins.
–Put the mainboard and peripherals back into their antistatic bags when not in use.
–For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the mainboard.
2014.11 | V6 | DOC |
Bosch Sicherheitssystem GmbH |
|
DIVAR IP 3000 |
Safety precautions | en |
9 |
|
|
|
1.4Operating precautions
The chassis cover must be in place when the system is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed.
Note:
Please handle used batteries carefully. Do not damage the battery in any way. A damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landfill. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly.
Bosch Sicherheitssystem GmbH |
2014.11 | V6 | DOC |
10 en | System overview |
DIVAR IP 3000 |
|
|
2 System overview
The DIVAR IP 3000 system is an affordable and easy to use all-in- one recording, viewing, and management solution for network surveillance systems of up to 32 channels. All channels are prelicensed. Running the full Bosch VMS solution and powered by Bosch VRM (Video Recording Manager) including the Video Streaming Gateway to integrate 3rd party cameras,
DIVAR IP 3000 is an intelligent IP storage device that eliminates the need for separate NVR (Network Video Recorder) server and storage hardware.
DIVAR IP 3000 is a 4-bay mini tower unit that combines advanced management and state-of-the-art recording management into a single cost-effective, plug and play IP recording appliance for IT-minded customers which are seeking for a state-of-the-art “second generation” DVR and NVR recording solution.
Easy to install and operate, DIVAR IP 3000 features wizardbased set-up and centralized configuration to reduce installation times. All components are pre-installed and pre-configured. Simply connect to the network and turn on the unit —
DIVAR IP 3000 is ready to begin recording straight out of the box.
Bosch Video Management System manages all IP and digital video and audio, plus all the security data being transmitted across your IP network. It seamlessly combines IP cameras and encoders, provides system-wide event and alarm management, system health monitoring, user and priority management. DIVAR IP 3000 features front-swappable SATA-II hard drives. All system software is pre-installed and pre-activated — creating an out-of-the-box ready-to-use video management appliance. DIVAR IP 3000 utilizes Windows Storage Server 2008 R2 operating system.
2014.11 | V6 | DOC |
Bosch Sicherheitssystem GmbH |
|
Loading...