Z170I PRO GAMING
Motherboard
E10725
First Edition
August 2015
Copyright © 2015 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either
(1)for free by downloading it from http://support.asus.com/download
or
(2)for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address gpl@asus.com, stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).
ii
Contents
Safety information....................................................................................... |
iv |
About this guide.......................................................................................... |
iv |
Package contents........................................................................................ |
vi |
Z170I PRO GAMING specifications summary........................................... |
vi |
Chapter 1: |
Product introduction |
|
|
1.1 |
Before you proceed...................................................................... |
1-1 |
|
1.2 |
Motherboard overview................................................................. |
1-1 |
|
1.3 |
Central Processing Unit (CPU).................................................... |
1-3 |
|
1.4 |
System memory............................................................................ |
1-7 |
|
1.5 |
Wi-Fi antenna installation.......................................................... |
1-10 |
|
1.6 |
Expansion slots.......................................................................... |
1-11 |
|
1.7 |
Headers |
........................................................................................ |
1-12 |
1.8 |
Connectors.................................................................................. |
1-13 |
|
1.9 |
Onboard .............................................................................LEDs |
1-22 |
|
1.10 |
Software ........................................................................support |
1-24 |
|
Chapter 2: |
BIOS information |
|
|
2.1 |
Managing and updating your BIOS |
............................................. 2-1 |
|
2.2 |
BIOS setup program..................................................................... |
2-6 |
|
2.3 |
My Favorites................................................................................ |
2-15 |
|
2.4 |
Main menu................................................................................... |
2-16 |
|
2.5 |
Ai Tweaker menu........................................................................ |
2-18 |
|
2.6 |
Advanced menu.......................................................................... |
2-26 |
|
2.7 |
Monitor menu.............................................................................. |
2-34 |
|
2.8 |
Boot menu................................................................................... |
2-38 |
|
2.9 |
Tool menu.................................................................................... |
2-43 |
|
2.10 |
Exit menu..................................................................................... |
2-44 |
|
Appendix |
|
|
|
Notices....................................................................................................... |
|
A-1 |
|
ASUS contact information........................................................................ |
A-6 |
||
iii
Safety information
Electrical safety
•To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
•When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
•Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
•Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.
•Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
•If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
Operation safety
•Before installing the motherboard and adding components, carefully read all the manuals that came with the package.
•Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
•To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
•Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may be exposed to moisture.
•Place the product on a stable surface.
•If you encounter technical problems with the product, contact a qualified service technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the motherboard.
How this guide is organized
This guide contains the following parts:
•Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it supports. It includes descriptions of the switches, jumpers, and connectors on the motherboard.
•Chapter 2: BIOS information
This chapter discusses changing system settings through the BIOS Setup menus. Detailed descriptions for the BIOS parameters are also provided.
iv
Where to find more information
Refer to the following sources for additional information and for product and software updates.
1.ASUS websites
The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.
2.Optional documentation
Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when completing a task.
CAUTION: Information to prevent damage to the components when completing a task
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text |
Indicates a menu or an item to select. |
Italics |
Used to emphasize a word or a phrase. |
<Key> |
Keys enclosed in the less-than and greater-than sign |
|
means that you must press the enclosed key. |
|
Example: <Enter> means that you must press the Enter or |
|
Return key. |
<Key1> + <Key2> + <Key3> |
If you must press two or more keys simultaneously, the key |
|
names are linked with a plus sign (+). |
v
Package contents
Check your motherboard package for the following items.
Motherboard |
ASUS Gaming Motherboard – Z170I PRO GAMING |
|
|
|
|
Cables |
4 x Serial ATA 6.0 Gb/s cables |
|
|
|
|
|
1 x I/O Shield |
|
|
1 x M.2 2242 Mounting Kit |
|
Accessories |
1 x M.2 screw package |
|
1 x PRO GAMING cable labels |
||
|
||
|
1 x CPU installation tool |
|
|
1 x Wi-Fi 2T2R Antenna |
|
|
|
|
Application DVD |
Support DVD |
|
|
|
|
Documentation |
User Guide |
|
|
|
If any of the above items is damaged or missing, contact your retailer.
Z170I PRO GAMING specifications summary
|
LGA1151 socket for Intel® 6th Generation Core™ i7 / i5 / i3, Pentium®, and |
|
|
Celeron® processors |
|
CPU |
Supports Intel® 14nm CPU |
|
Supports Intel® Turbo Boost Technology 2.0* |
||
|
||
|
* The Intel® Turbo Boost Technology 2.0 support depends on the CPU types. |
|
|
** Refer to www.asus.com for Intel® CPU support list. |
|
Chipset |
Intel® Z170 Express Chipset |
|
|
2 x DIMM, max. 32GB, DDR4 3400(O.C.)*/ 3333(O.C.)*/ 3200(O.C.)*/ |
|
|
3100(O.C.)*/ 3000(O.C.)*/ 2933(O.C.)*/ 2800(O.C.)*/ 2666(O.C.)*/ |
|
|
2600(O.C.)*/ 2400(O.C.)*/ 2133 MHz, non-ECC, un-buffered memory |
|
Memory |
Dual-channel memory architecture |
|
|
Supports Intel® Extreme Memory Profile (XMP) |
|
|
* Hyper DIMM support is subject to the physical characteristics of individual CPUs. |
|
|
** Refer to www.asus.com for the latest Memory QVL (Qualified Vendors List). |
|
|
|
|
|
Integrated Graphics Processor - Intel® HD Graphics support |
|
|
Multi-VGA output support: DisplayPort, HDMI |
|
|
Supports DisplayPort with max. resolution 4096 x 2304 @60Hz |
|
Graphics |
Supports HDMI with max. resolution 4096 x 2160 @ 24 Hz / 2560 x 1600 @ 60 |
|
Hz /1920 x 1080@ 120 Hz |
||
|
||
|
Supports Intel® InTru™ 3D, Quick Sync Video, Clear Video HD Technology, |
|
|
Insider™ |
|
|
Maximum shared memory of 1024 MB |
|
|
|
|
Expansion slots |
1 x PCI Express 3.0 x16 slot |
|
|
|
|
|
(continued on the next page) |
vi
Z170I PRO GAMING specifications summary
|
SupremeFX 8-Channel High Definition Audio CODEC |
||
|
- Supports : Jack-detection, Multi-streaming, Front Panel MIC Jack- |
||
|
|
retasking |
|
|
- High quality 115dB SNR stereo playback output |
||
Audio |
Audio Features : |
||
|
- |
SupremeFX Shielding™ Technology |
|
|
- |
Headphone AMP |
|
|
- Optical S/PDIF out port at back panel |
||
|
- |
Sonic Radar II |
|
|
Intel® Z170 Express Chipset with RAID 0, 1, 5, 10 and Intel® Rapid Storage |
||
|
Technology 14 support |
||
|
- |
1 x SATA Express port (gray, compatible with 2 x SATA 6.0 Gb/s ports) |
|
Storage |
- |
1 x M.2 Socket 3 with M key, type 2242/2260/2280 storage devices |
|
|
|
support (both SATA & PCIE x4 mode) |
|
|
- |
4 x SATA 6.0 Gb/s ports (gray, 2 from SATA Express Port) |
|
|
- |
Supports Intel® Smart Response Technology |
|
|
Intel® Gigabit LAN |
||
LAN |
Anti-surge LANGuard |
||
|
GameFirst III |
||
Wireless Data |
Speedy Wi-Fi 802.11 a/b/g/n/ac supports dual frequency band 2.4/5 GHz + |
||
Network |
Bluetooth |
||
|
|
||
|
ASMedia® USB 3.1 Controller - supports ASUS USB 3.1 Boost |
||
|
- 2 x USB 3.1 ports (2 Type-A, red, black at back panel) |
||
USB |
Intel® Z170 Express Chipset |
||
- 6 x USB 3.0/2.0 ports (2 ports at mid-board; 4 ports at back panel, blue) |
|||
|
|||
|
- 4 x USB 2.0/1.1 ports (2 ports at mid-board; 2 ports at back panel, black) |
||
|
* with ASUS USB 3.0 Boost support |
||
|
|
||
|
1 x 19-pin USB 3.0/2.0 connector supports additional 2 USB 3.0/2.0 ports |
||
|
1 x USB 2.0/1.1 connectors support additional 2 USB 2.0/1.1 ports |
||
|
1 x System panel header |
||
|
1 x Front panel audio connector (AAFP) |
||
|
4 x SATA 6.0 Gb/s connectors (gray, 2 from SATA Express Port) |
||
|
1 x M.2 Socket 3 for M Key, type 2242/2260/2280 devices |
||
Internal |
1 x SATA Express connector: gray, compatible with 2 x SATA 6.0 Gb/s ports |
||
1 x CPU fan connector (4-pin) |
|||
connectors |
|||
|
|
||
|
2 x Chassis Fan connectors (4-pin) for both 3-pin(DC mode) and 4-pin (PWM |
||
|
mode) coolers control |
||
|
1 x Speaker header |
||
|
1 x TPM header |
||
|
1 x 24-pin EATX Power connector |
||
|
1 x 8-pin EATX 12V Power connector |
||
|
1 x Clear CMOS jumper (2-pin) |
||
|
|
(continued on the next page) |
|
vii
Z170I PRO GAMING specifications summary
|
Gamer’s Guardian II |
|
|
- |
DIGI+ VRM |
|
- |
DRAM Overcurrent Protection |
|
- |
ESD Guards on VGA, LAN, Audio, KBMS and USB3.1/3.0/2.0 ports |
|
- |
Highly durable components |
|
- Stainless Steel Back I/O |
|
|
Performance Optimization |
|
|
ASUS DIGI+ VRM |
|
|
- |
ASUS DIGI+ VRM utility |
|
ASUS EPU |
|
|
- |
EPU |
|
ASUS TPU |
|
|
- |
Auto Tuning, TurboV, GPU Boost |
|
Fan Xpert 2+ |
|
|
RAM Cache |
|
|
Media Streamer |
|
ASUS gaming |
- |
Pipe music or movies from your PC to a smart TV, your entertainment |
|
goes wherever you go! |
|
features |
- |
Media Streamer app for portable smartphone/tablet, supporting iOS 7 & |
|
||
|
|
Android 4.0 systems |
|
EZ DIY |
|
Push Notice
-Monitor your PC status with smart devices in real time
-UEFI BIOS EZ Mode featuring friendly graphics user interface
-O.C. Tuner
-CrashFree BIOS 3
-EZ Flash 3
Q-Design
-ASUS Q-Shield
-ASUS Q-DIMM
-ASUS Q-LED (CPU, DRAM, VGA, Boot Device LED)
ASUS Exclusive Features
-USB 3.1 Boost featuring speedy USB 3.1 transmission
-AI Suite 3
-Disk Unlocker
-AI Charger+
-ASUS CPU-Z
(continued on the next page)
viii
Z170I PRO GAMING specifications summary
|
1 x PS/2 keyboard/mouse combo port |
|
|
1 x Optical S/PDIF out |
|
|
1 x HDMI |
|
|
1 x DisplayPort |
|
Rear Panel I/O |
2 x Wi-Fi antenna ports |
|
ports |
1 x LAN (RJ45) port |
|
|
2 x USB 3.1 ports (2 Type-A, red) |
|
|
4 x USB 3.0/2.0 ports |
|
|
2 x USB 2.0/1.1 ports |
|
|
8-channel audio I/O ports |
|
|
128Mb Flash ROM, UEFI AMI BIOS, PnP, DMI 2.7, WfM2.0, SM BIOS 2.7, |
|
|
ACPI 5.0, Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS 3, F11 |
|
BIOS features |
EZ Tuning Wizard, F6 Qfan Control, F3 My Favorites, Quick Note, Last |
|
|
Modified log, F12 PrintScreen, and ASUS DRAM SPD (Serial Presence |
|
|
Detect) memory information |
|
Manageability |
WfM 2.0, DMI 2.7, WOL by PME, PXE |
|
|
|
|
|
Drivers |
|
Support DVD |
ASUS utilities |
|
EZ Update |
||
|
||
|
Anti-virus software (OEM version) |
|
|
Windows® 10 |
|
OS support |
Windows® 8.1 |
|
Windows® 7 |
||
|
* Please refer to ASUS official website and download “Windows® 7 Installation Guide” |
|
|
and “EZ Installer” to install Windows® 7. |
|
Form factor |
Mini-ITX Form Factor, 6.7”x 6.7” (17cm x 17cm) |
|
|
|
Specifications are subject to change without notice.
ix
x
Product introduction |
1 |
1.1Before you proceed
Take note of the following precautions before you install motherboard components or change any motherboard settings.
• Unplug the power cord from the wall socket before touching any component.
•Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
•Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.
1.2Motherboard overview
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits.
Unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage to motherboard components.
1.2.1Placement direction
When installing the motherboard, place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image.
1.2.2Screw holes
Place four screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
ASUS Z170I PRO GAMING |
1-1 |
Place this side towards the rear of the chassis
1.2.3Motherboard layout
1 |
2 |
3 |
4 |
4 |
17.0cm(6.7in)
|
|
CPU_LED |
KBMS_USB910 CPU_FAN |
EATX12V |
|
|
DIGI |
|
|
|
|
|
DIGI |
+VRM |
|
+EPU |
|
HDMI_DP CHA_FAN2
|
USB3_5-8 |
18 |
LGA1151 |
|
LAN1 _USB3.1
_E12 ASM 1142
M.2(WIFI)
|
|
I219V |
17 |
BATT_CON |
Super |
I/O |
||
16 |
|
AAFP |
|
AUDIO |
SUPREMEFX |
|
|
|
|
|
ALC |
|
|
1150 |
|
SupremeFX LED |
|
128Mb |
BIOS |
SPDIF_OUT
TPU
TPM CHA_FAN1
VGA_LED
|
BOOT_DEVICE_LED |
|
|
M.2(SOCKET3) |
3 |
Intel® |
SATA6G4 |
|
|
|
|
H170 |
|
SATA6G |
|
CLRTC |
|
SB_PWR 
PCIEX16
15 |
4 |
1 |
14 |
13 |
12 11 |
5 |
|
4 |
|
|
|
|
A1DIMMDDR4(64bit, 288-pin module) |
B1DIMMDDR4(64bit, 288-pin module) |
|
|
SATA6G2SATA6G1 EATX PWR |
17.0cm(6.7in) |
2 |
SPEAKER |
F PANEL |
7 |
||||
|
|
LED DRAM |
|
|
|
|
|
|
|
|
|
|
6 |
|
|
12 USB1112 |
|
SATAEXPRESS |
|
8 |
|
|
_ |
|
|
|
|
|
|
USB3 |
|
|
|
|
|
|
|
|
|
|
9 |
7 |
|
10 |
|
|
|
|
1-2 |
Chapter 1: Product introduction |
1.2.4Layout contents
Connectors/Jumpers/Slots/LED |
Page |
|
1. |
CPU, chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1~2) |
1-16 |
2. |
ATX power connectors (24-pin EATXPWR, 8-pin ATX12V) |
1-17 |
3. |
Intel® LGA1151 CPU socket |
1-3 |
4. |
Q LEDs (BOOT_DEVICE_LED, VGA_LED, DRAM_LED, CPU_LED) |
1-22 |
5. |
DDR4 DIMM slots |
1-7 |
6. |
System panel connector (10-1 pin F_PANEL) |
1-20 |
7. |
Intel® Z170 Serial ATA 6.0 Gb/s connector (7-pin SATA6G_1~4, |
1-19 |
|
SATAEXPRESS) |
|
|
|
|
8. |
USB 3.0 connector (20-1 pin USB3_12) |
1-18 |
9. |
USB 2.0 connector (10-1 pin USB1112) |
1-18 |
10. |
Speaker connector (4-pin SPEAKER) |
1-19 |
11. |
Clear RTC RAM (2-pin CLRTC) header |
1-12 |
12. |
Standby Power LED (SB_PWR) |
1-22 |
13. |
M.2 Socket 3 |
1-21 |
14. |
TPM connector (14-1 pin TPM) |
1-15 |
15. |
SupremeFX LED Lighting |
1-23 |
16. |
Front panel audio connector (10-1 pin AAFP) |
1-16 |
17. |
RTC battery header (2-pin BATT_CON) |
1-12 |
18. |
Digital audio connector (4-1 pin SPDIF_OUT) |
1-15 |
1.3Central Processing Unit (CPU)
This motherboard comes with a surface mount LGA1151 socket designed for the 6th Generation Intel® Core™ i7 / Core™ i5 / Core™ i3, Pentium® , and Celeron® processors.
Z170I PRO GAMING CPU socket LGA1151
ASUS Z170I PRO GAMING |
1-3 |
Unplug all power cables before installing the CPU.
•Ensure that you install the correct CPU designed for the LGA1151 socket only. DO
NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets on the
LGA1151 socket.
•Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
•Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA1151 socket.
•The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.
1.3.1Installing the CPU
Top of CPU
1-4 |
Chapter 1: Product introduction |
Bottom of CPU
Bottom of CPU
Top of CPU
ASUS Z170I PRO GAMING |
1-5 |
To install the CPU heatsink and fan assembly
1 A 2
B
B
A
3 |
4 |
To uninstall the CPU heatsink and fan assembly
1 |
2 |
|
A
B B 
A
1-6 |
Chapter 1: Product introduction |
1.4System memory
1.4.1Overview
This motherboard comes with two Double Data Rate 4 (DDR4) Dual Inline Memory Module (DIMM) sockets. A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
According to Intel® CPU spec, DIMM voltage below 1.2 V is recommended to protect the CPU.
DIMM_B1
DIMM_A1
Z170I PRO GAMING 288-pin DDR4 DIMM sockets
1.4.2Memory configurations
You may install 2 GB, 4 GB, 8 GB, and 16 GB unbuffered non-ECC DDR4 DIMMs into the DIMM sockets. You can refer to the recommended memory population below.
Recommended memory configurations
ASUS Z170I PRO GAMING |
1-7 |
•You may install varying memory sizes in Channel A and Channel B. The system
maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
•Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB or more memory on the motherboard, the actual usable memory for the OS can be about 3GB or less. For effective use of memory, we recommend that you do any of the following:
-Use a maximum of 3 GB system memory if you are using a 32-bit Windows® OS.
-Install a 64-bit Windows® OS if you want to install 4GB or more on the motherboard.
-For more details, refer to the Microsoft® support site at http://support.microsoft. com/kb/929605/en-us.
• The default memory operation frequency is dependent on its Serial Presence Detect (SPD), which is the standard way of accessing information from a memory module. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value. To operate at the vendor-marked or at a higher frequency, refer to section 2.5 Ai Tweaker menu for manual memory frequency adjustment.
•Always install the DIMMS with the same CAS Latency. For an optimum compatibility, we recommend that you install memory modules of the same version or data code (D/C) from the same vendor. Check with the vendor to get the correct memory modules.
•Visit the ASUS website at www.asus.com for the latest QVL.
1.4.3Installing a DIMM
1
1-8 |
Chapter 1: Product introduction |
2
3
To remove a DIMM
B 
A
ASUS Z170I PRO GAMING |
1-9 |
1.5Wi-Fi antenna installation
Connect the bundled ASUS 2T2R dual band Wi-Fi antenna connector to the Wi-Fi ports at the back of the chassis.
IO Shield
• Ensure that the ASUS 2T2R dual band Wi-Fi antenna is securely installed to the Wi-Fi ports.
•Ensure that you install the Bluetooth driver before installing the Wi-Fi GO! software.
•Ensure that the antenna is at least 20 cm away from all persons.
The illustration above is for reference only. The I/O port layout may vary with models, but the Wi-Fi antenna installation procedure is the same for all models.
1-10 |
Chapter 1: Product introduction |
1.6Expansion slots
In the future, you may need to install expansion cards. The following sub sections describe the slots and the expansion cards that they support.
Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
1.6.1Installing an expansion card
To install an expansion card:
1.Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.
2.Remove the system unit cover (if your motherboard is already installed in a chassis).
3.Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.
4.Align the card connector with the slot and press firmly until the card is completely seated on the slot.
5.Secure the card to the chassis with the screw you removed earlier.
6.Replace the system cover.
1.6.2Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for information on BIOS setup.
2.Assign an IRQ to the card.
3.Install the software drivers for the expansion card.
1.6.3PCI Express 3.0 x16 slot
This motherboard has one PCI Express 3.0 x16 slot that supports PCI Express 3.0 x16 graphic cards complying with the PCI Express specifications.
IRQ assignments for this motherboard
|
|
A |
B |
C |
I.G.D. |
|
Shared |
– |
– |
|
||||
|
|
|
|
|
HD Audio Controller |
|
Shared |
– |
– |
XHCI Controller |
|
Shared |
– |
Shared |
SATA Controller |
|
Shared |
– |
– |
Intel LAN |
|
Shared |
– |
– |
WIFI |
|
– |
Shared |
– |
PCIE x16_1 |
|
Shared |
– |
– |
Asmedia U3.1 |
|
– |
Shared |
Shared |
ASUS Z170I PRO GAMING |
1-11 |
1.7Headers
1.Clear RTC RAM (2-pin CLRTC)
This header allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
CLRTC |
|
BAT |
|
_ |
GND |
+3V |
|
PIN 1 |
|
Z170I PRO GAMING Clear RTC RAM
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Use a metal object such as a screwdriver to short the two pins. 3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup to reenter data.
• If the steps above do not help, remove the onboard battery and short the two pins again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
• You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature. Shut down and reboot the system, then the BIOS automatically resets parameter settings to default values.
2. RTC Battery header (2-pin BATT_CON)
This connector is for the lithium CMOS battery.
BATT_CON
PIN 1
VBAT
GND
Z170I PRO GAMING RTC battery header
1-12 |
Chapter 1: Product introduction |
1.8Connectors
1.8.1Rear panel connectors
|
1 |
|
2 |
|
|
|
|
|
3 |
4 5 |
6 |
7 |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
14 |
13 |
12 |
11 |
10 |
9 |
8 |
1.PS/2 Mouse/Keyboard combo port. This port connects to a PS/2 mouse or PS/2 keyboard.
2 DisplayPort. This port connects a display monitor or a home-theater system.
3.LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub.
LAN port LED indications
Activity/Link LED |
Speed LED |
||
Status |
Description |
Status |
Description |
Off |
No link |
OFF |
10Mbps connection |
Orange |
Linked |
ORANGE |
100Mbps connection |
Orange |
Data activity |
GREEN |
1Gbps connection |
(Blinking) |
|
|
|
Orange |
Ready to wake |
|
|
(Blinking |
up from S5 |
|
|
then steady) |
mode |
|
|
ACT/LINK SPEED LED LED
LAN port
4.Center / Subwoofer port (orange). This port connects the center/subwoofer speakers.
5.Rear Speaker Out port (black). This port connects the rear speakers in a 4.1 channel, 5.1 channel, or 7.1 channel audio configuration.
6.Line In port (light blue). This port connects to the tape, CD, DVD player, or other audio sources.
7.Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1, and 7.1-channel configurations, the function of this port becomes Front Speaker Out.
ASUS Z170I PRO GAMING |
1-13 |
8.Microphone port (pink). This port connects to a microphone.
9.Optical S/PDIF out port. This port allows you to connect your PC to amplified speakers, headphones, or Sony/Phillips Digital Interconnect Format (S/PDIF) compliant devices.
Refer to the audio configuration table for the function of the audio ports in 2.1, 4.1, 5.1 or 7.1-channel configuration.
Audio 2, 4.1, 5.1, or 7.1-channel configuration
Port |
Headset |
4.1-channel |
5.1-channel |
7.1-channel |
|
2-channel |
|||||
|
|
|
|
||
Light Blue |
Line In |
Line In |
Line In |
Line In |
|
Lime |
Line Out |
Front Speaker Out |
Front Speaker Out |
Front Speaker Out |
|
Pink |
Mic In |
Mic In |
Mic In |
Mic In |
|
Orange |
– |
– |
Center/Subwoofer |
Center/Subwoofer |
|
Optical S/ |
– |
– |
– |
Side Speaker Out |
|
PDIF out |
|
|
|
|
|
Black |
– |
Rear Speaker Out |
Rear Speaker Out |
Rear Speaker Out |
10.ASUS WLAN Cards. These WLAN cards allow your computer to connect to a wireless network.
For details, refer to the section 1.5 Wi-Fi antenna installation.
11.USB 3.1 Type A port. This Universal Serial Bus (USB) Type A port is for USB 3.1 peripheral devices.
12.USB 3.0 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.0 devices.
• USB 3.0 devices can only be used for data storage.
• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster and better performance from your USB 3.0 devices.
•Due to the design of the Intel® 100 series chipset, all USB devices connected to the USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB devices must update their firmware for better compatibility.
13. HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector, and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected content.
14.USB 2.0 ports. These 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices.
1-14 |
Chapter 1: Product introduction |
1.8.2Internal connectors
1.TPM connector (14-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which securely store keys, digital certificates, passwords and data. A TPM system also helps enhance the network security, protects digital identities, and ensures platform integrity.
TPM
CLKRUN_F SERIRQ_F FRAME#_F LAD3_F LAD2_F LAD1_F LAD0_F
PIN 1
S 
__C _PCIRST#_PCICLK +3VSBTBDGNDTPM+3V+3V
Z170I PRO GAMING TPM connector
2.Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+5V |
SPDIFOUT GND |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SPDIF_OUT
Z170I PRO GAMING Digital audio connector
The S/PDIF module is purchased separately.
ASUS Z170I PRO GAMING |
1-15 |
3.CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1~2)
Connect the fan cable to the fan connector on the motherboard, ensuring that the black wire of the cable matches the ground pin of the connector
A
B
C
A B
CPU_FAN |
CHA_FAN2 |
|||||||||||||||
|
|
|
|
|
|
|
|
GND |
|
|
|
GND |
||||
|
|
|
|
|
|
|
|
CPU FAN PWR |
|
|
|
CHA FAN PWR |
||||
|
|
|
|
|
|
|
|
CPU FAN IN |
|
|
|
CHA FAN IN |
||||
|
|
|
|
|
|
|
|
CPU FAN PWM |
|
|
|
+5V |
||||
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
C |
|
|
|
|
|||||||||
CHA_FAN1 |
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+5V CHA FAN IN CHA FAN PWR GND |
|
|
|
|
||||||||||
Z170I PRO GAMING Fan connectors
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan of maximum 1A (12 W) fan power.
4.Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
AAFP
SENSE2_RETUR |
PORT2 L |
NC |
Line out_L |
|
SENSE_SEND |
|
NC |
SENSE1_RETUR |
PORT2 R |
NC |
Line out_R |
NC |
PORT1 R |
NC |
MICPWR |
AGND |
PORT1 L |
AGND |
MIC2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PIN 1 |
PIN 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HD-audio-compliant |
Legacy AC’97 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
pin definition |
compliant definition |
Z170I PRO GAMING Front panel audio connector
•We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
•If you want to connect a high-definition front panel audio module to this connector, set the Front Panel Type item in the BIOS setup to [HD]. If you want to connect an AC’97 front panel audio module to this connector, set the item to [AC97]. By default, this connector is set to [HD]. See section 2.6.7 Onboard Devices Configuration for details.
1-16 |
Chapter 1: Product introduction |
Loading...