Asus Z10PC-D8/SAS, Z10PC-D8/10G-2S User’s Manual

Z10PC-D8 Series

User Guide

E13694

Revised Edition V3

December 2017

Copyright © 2017 ASUSTeK COMPUTER INC. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

ii

Contents

Notices ......................................................................................................................	viii
Safety information.......................................................................................................	x
Z10PC-D8 Series specifications summary.............................................................	xiii

Chapter 1: Product Introduction

1.1	Welcome!	.....................................................................................................	1-2
1.2	Package contents.......................................................................................		1-2
1.3	Serial number label.....................................................................................		1-3
1.4	Special features..........................................................................................		1-3
	1.4.1	Product highlights........................................................................	1-3
	1.4.2	Innovative ASUS features............................................................	1-4

Chapter 2: Hardware Information

2.1	Before you proceed....................................................................................		2-2
2.2	Motherboard overview...............................................................................		2-3
	2.2.1	Placement direction.....................................................................	2-3
	2.2.2	Screw holes.................................................................................	2-3
	2.2.3	Motherboard layout......................................................................	2-4
	2.2.4	Layout contents...........................................................................	2-8
2.3	Central Processing Unit (CPU)................................................................		2-10
	2.3.1	Installing the CPU......................................................................	2-10
2.4	System memory........................................................................................		2-15
	2.4.1	Overview....................................................................................	2-15
	2.4.2	Memory Configurations..............................................................	2-15
	2.4.3	Installing a DIMM on a single clip DIMM socket........................	2-17
2.5	Expansion slots........................................................................................		2-18
	2.5.1	Installing an expansion card......................................................	2-18
	2.5.2	Configuring an expansion card..................................................	2-18
	2.5.3	Interrupt assignments................................................................	2-19
	2.5.4	PCI Express x16 slot (x16 link)..................................................	2-19
	2.5.5	PCI Express x8 slot (x8 link)......................................................	2-19
	2.5.6	PCI Express x8 slot (x4 link)......................................................	2-19
	2.5.7	Installing ASMB8 series management board.............................	2-21

iii

Contents

2.6	Onboard LEDs...........................................................................................		2-22
2.7	Jumpers	.....................................................................................................	2-27
2.8	Connectors................................................................................................		2-31
	2.8.1 ...............................................................	Rear panel connectors	2-31
	2.8.2 ....................................................................	Internal connectors	2-33

Chapter 3: Powering Up

3.1	Starting up for the first time......................................................................		3-2
3.2	Powering off the computer........................................................................		3-3
	3.2.1	Using the OS shut down function................................................	3-3
	3.2.2	Using the dual function power switch..........................................	3-3

Chapter 4: BIOS Setup

4.1	Managing and updating your BIOS...........................................................		4-2
	4.1.1	ASUS CrashFree BIOS 3 utility...................................................	4-2
	4.1.2	ASUS EZ Flash Utility..................................................................	4-3
	4.1.3	BUPDATER utility........................................................................	4-4

4.2	BIOS setup program...................................................................................		4-6
	4.2.1	BIOS menu screen......................................................................	4-7
	4.2.2	Menu bar......................................................................................	4-7
	4.2.3	Menu items..................................................................................	4-8
	4.2.4	Submenu items............................................................................	4-8
	4.2.5	Navigation keys...........................................................................	4-8
	4.2.6	General help................................................................................	4-8
	4.2.7	Configuration fields......................................................................	4-8
	4.2.8	Pop-up window............................................................................	4-8
	4.2.9	Scroll bar......................................................................................	4-8

4.3	Main menu...................................................................................................		4-9
	4.3.1	System Date [Day xx/xx/xxxx].....................................................	4-9
	4.3.2	System Time [xx:xx:xx]................................................................	4-9
4.4	Advanced menu........................................................................................		4-10
	4.4.1	ACPI Settings............................................................................	4-11
	4.4.2	Smart Settings...........................................................................	4-11
	4.4.3	NCT6779D Super IO Configuration...........................................	4-12
	4.4.4	Onboard LAN I210 Configuration .............................................	4-13
	4.4.5	Serial Port Console Redirection.................................................	4-14
	4.4.6	APM...........................................................................................	4-17
	4.4.7	Advanced Power Management Configuration...........................	4-18

iv

Contents

	4.4.8	PCI Subsystem Settings............................................................	4-18
	4.4.9	Network Stack Configuration.....................................................	4-19
	4.4.10	CSM Configuration....................................................................	4-20
	4.4.11	Trusted Computing....................................................................	4-21
	4.4.12	USB Configuration.....................................................................	4-22
	4.4.13	iSCSI Configuration...................................................................	4-23
4.5	IntelRCSetup menu...................................................................................		4-24
	4.5.1	Processor Configuration............................................................	4-25
	4.5.2	Advanced Power Management Configuration...........................	4-27
	4.5.3	Common RefCode Configuration...............................................	4-28
	4.5.4	QPI Configuration......................................................................	4-29
	4.5.5	Memory Configuration...............................................................	4-30
	4.5.6	IIO Configuration........................................................................	4-34
	4.5.7	PCH Configuration.....................................................................	4-35
	4.5.8	Miscellaneous Configuration......................................................	4-38
	4.5.9	Server ME Configuration...........................................................	4-38
	4.5.10	Runtime Error Logging Support.................................................	4-39
4.6	Server Mgmt menu...................................................................................		4-40
4.7	Event Logs menu......................................................................................		4-45
	4.7.1	Change Smbios Event Log Settings..........................................	4-45
	4.7.2	View Smbios Event Log.............................................................	4-46
4.8	Monitor menu............................................................................................		4-47
4.9	Security menu...........................................................................................		4-48
4.10	Boot menu.................................................................................................		4-51
4.11	Tool menu..................................................................................................		4-52
4.12	Exit menu...................................................................................................		4-53

Chapter 5: RAID Configuration

5.1	Setting up RAID..........................................................................................		5-2
	5.1.1	RAID definitions...........................................................................	5-2
	5.1.2	Installing hard disk drives............................................................	5-3
	5.1.3	Setting the RAID item in BIOS.....................................................	5-3
	5.1.4	RAID configuration utilities...........................................................	5-3

5.2	LSI Software RAID Configuration Utility...................................................		5-4
	5.2.1	Creating a RAID set.....................................................................	5-5
	5.2.2	Adding or viewing a RAID configuration....................................	5-11
	5.2.3	Initializing the virtual drives........................................................	5-12
	5.2.4	Rebuilding failed drives..............................................................	5-16

v

Contents

5.2.5	Checking the drives for data consistency..................................	5-18
5.2.6	Deleting a RAID configuration...................................................	5-21
5.2.7	Selecting the boot drive from a RAID set...................................	5-22
5.2.8	Enabling WriteCache.................................................................	5-23

5.3Intel® Rapid Storage Technology enterprise SATA/SSATA

	Option ROM Utility....................................................................................		5-24
	5.3.1	Creating a RAID set...................................................................	5-25
	5.3.2	Deleting a RAID set...................................................................	5-27
	5.3.3	Resetting disks to Non-RAID.....................................................	5-28
	5.3.4	Exiting the Intel® Rapid Storage Technology enterprise
		SATA/SSATA Option ROM utility..............................................	5-29
	5.3.5	Rebuilding the RAID..................................................................	5-29
	5.3.6	Setting the Boot array in the BIOS Setup Utility........................	5-31
5.4	Intel® Rapid Storage Technology enterprise (Windows)......................		5-32
	5.4.1	Creating a RAID set...................................................................	5-33
	5.4.2	Changing a Volume Type..........................................................	5-35
	5.4.3	Deleting a volume......................................................................	5-36
	5.4.4	Preferences...............................................................................	5-37
5.5	LSI Corporation MPT Setup Utility..........................................................		5-38
	5.5.1	RAID 1 volume...........................................................................	5-39
	5.5.2	RAID 1E/10 volume...................................................................	5-45
	5.5.3	RAID 0 volume...........................................................................	5-51
	5.5.4	Managing the RAID Volumes....................................................	5-57
	5.5.5	Viewing SAS topology...............................................................	5-68
	5.5.6	Global Properties.......................................................................	5-69

Chapter 6: Driver installation

6.1	RAID driver installation..............................................................................		6-2
	6.1.1	Creating a RAID driver disk.........................................................	6-2
	6.1.2	Installing the RAID controller driver.............................................	6-3
6.2	Management applications and utilities installation...............................		6-13
6.3	Running the Support DVD ......................................................................		6-13
6.4	Intel® chipset device software installation.............................................		6-17
6.5	Installing the Intel® I210 Gigabit Adapters driver..................................		6-19
6.6	VGA driver installation.............................................................................		6-22
6.7	Intel® Rapid Storage Technology enterprise 4.1 installation................		6-24

vi

Contents

Appendix

Z10PC-D8 Series block diagram.............................................................................	A-2
Simplified EU Declaration of Conformity...............................................................	A-6
ASUS contact information......................................................................................	A-7

vii

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•This device may not cause harmful interference, and

•This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Compliance Statement of Innovation, Science and Economic

Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(A)/NMB-3(A)

Déclaration de conformité de Innovation, Sciences et Développement économique Canada (ISED)

Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

CAN ICES-3(A)/NMB-3(A)

viii

REACH

Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of

Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.

DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

Australia statement notice

From 1 January 2012 updated warranties apply to all ASUS products, consistent with the Australian Consumer Law. For the latest product warranty details please visit https://www. asus.com/support. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at https://www.asus.com/support

ix

Safety information

Electrical safety

•To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

•When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

•Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.

•Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.

•Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.

•If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety

•Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.

•Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.

•To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.

•Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.

•Place the product on a stable surface.

•If you encounter technical problems with the product, contact a qualified service technician or your retailer.

x

About this guide

This user guide contains the information you need when installing and configuring the motherboard.

How this guide is organized

This user guide contains the following parts:

•Chapter 1: Product Introduction

This chapter describes the features of the motherboard and the new technologies it supports.

•Chapter 2: Hardware Information

This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the switches, jumpers, and connectors on the motherboard.

•Chapter 3: Powering Up

This chapter describes the power up sequence and ways of shutting down the system.

•Chapter 4: BIOS Setup

This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.

•Chapter 5: RAID Configuration

This chapter provides instructions for setting up, creating, and configuring RAID sets using the available utilities.

•Chapter 6: Driver Installation

This chapter provides instructions for installing the necessary drivers for different system components.

•Appendix: Reference Information

This appendix includes additional information that you may refer to when configuring the motherboard.

Where to find more information

Refer to the following sources for additional information and for product and software updates.

1.ASUS websites

The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.

2.Optional documentation

Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.

xi

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task.

CAUTION: Information to prevent damage to the components when trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task..

NOTE: Tips and additional information to help you complete a task.

Typography
Bold text	Indicates a menu or an item to select.
Italics	Used to emphasize a word or a phrase.
<Key>	Keys enclosed in the less-than and greater-than sign means
	that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or Return key.

<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).

Command	Example: <Ctrl> + <Alt> + <Del>
	Means that you must type the command exactly as shown, then
	supply the required item or value enclosed in brackets.
	Example: At DOS prompt, type the command line:
	format A:/S

xii

Z10PC-D8 Series specifications summary

Model Name		Z10PC-D8/SAS/10G-2S		Z10PC-D8/SAS
		2 x Socket R3 (LGA 2011-3)
Processor / System Bus		Intel® Xeon® processor E5-2600 V3 product family
		QPI 6.4 / 8.0 / 9.6 GT/s
Core Logic		Intel® C612 PCH
Form Factor		CEB 12” x 10.5” (ATX Mounting Hole Locations)
	Fan Speed
	Control
ASUS	Rack Ready
	(Rack and
Features	Pedestal dual
	use)
	ASWM
	Enterprise
	Total Slots	8 (4 channels per CPU, 4 DIMMs per CPU)
	Voltage	1.2 V
	Capacity	Maximum up to 512 GB
Memory	Memory Type	DDR4 2133 / 1866 / 1600 / 1333* RDIMM / LR-DIMM / NVDIMM
		* Refer to www.asus.com for the latest memory AVL update
	Memory Size	4 GB, 8 GB, 16 GB, 32 GB (RDIMM)
		32 GB, 64 GB (LR-DIMM)
Expansion	Total PCI-E Slots	3
Slots (follow	Slot Location 1	1 x PCI-E x8 (X4 Gen2 Link) ; MIO supported
SSI Location	Slot Location 5	1 x PCI-E x16 (X16 Gen3 Link)
number)	Slot Location 6	1 x PCI-E x8 (X8 Gen3 Link)
		Intel® C612
		- 10 x SATA 6 Gb/s ports
	SATA Controller	or 9 x SATA 6 Gb/s ports with 1 x M.2 connector (SATA 6 Gb/s &
Storage		PCI-E Gen2 x1 link)
		Intel® RSTe (for Windows only; Support software RAID 0, 1, 10 & 5)
	SAS Upgrade	Onboard LSI 3008 8-port SAS 12G Controller
		(2 Mini-SAS HD SFF-8643)

(continued on the next page)

xiii

Z10PC-D8 Series specifications summary

Model Name		Z10PC-D8/10G-2S		Z10PC-D8
		2 x Socket R3 (LGA 2011-3)
Processor / System Bus		Intel® Xeon® processor E5-2600 V3 product family
		QPI 6.4 / 8.0 / 9.6 GT/s
Core Logic		Intel® C612 PCH
Form Factor		CEB 12” x 10.5” (ATX Mounting Hole Locations)
	Fan Speed
	Control
ASUS	Rack Ready
	(Rack and
Features	Pedestal dual
	use)
	ASWM
	Enterprise
	Total Slots	8 (4 channels per CPU, 4 DIMMs per CPU)
	Voltage	1.2 V
	Capacity	Maximum up to 512 GB
Memory	Memory Type	DDR4 2133 / 1866 / 1600 / 1333* RDIMM / LR-DIMM / NVDIMM
		* Refer to www.asus.com for the latest memory AVL update
	Memory Size	4 GB, 8 GB, 16 GB, 32 GB (RDIMM)
		32 GB, 64 GB (LR-DIMM)
Expansion	Total PCI-E Slots 3
Slots (follow	Slot Location 1	1 x PCI-E x8 (X4 Gen2 Link) ; MIO supported
SSI Location	Slot Location 5	1 x PCI-E x16 (X16 Gen3 Link)
number)	Slot Location 6	1 x PCI-E x8 (X8 Gen3 Link)

Intel® C612

- 10 x SATA 6 Gb/s ports

or 9 x SATA 6 Gb/s ports with 1 x M.2 connector (SATA 6 Gb/s & SATA Controller PCI-E Gen2 x1 link)

Storage Intel® RSTe (for Windows only; Support software RAID 0, 1, 10 & 5)

LSI MegaRAID driver supports software RAID 0, 1& 10 (Windows & Linux)

Optional kits:

SAS Upgrade ASUS PIKE II 3008 8-port SAS 12G RAID card

ASUS PIKE II 3108 8-port SAS 12G HW RAID card

(continued on the next page)

xiv

Z10PC-D8 Series specifications summary

	Model Name		Z10PC-D8/SAS/10G-2S	Z10PC-D8/SAS
			1 x Dual Port BCM57840S
	Networking	LAN	10GbE Controller	2 x Intel I210AT
			2 x Intel I210AT	1 x Management port
			1 x Management port
	Graphic	VGA	Aspeed AST2400 32MB
		TPM Header	1
			24-pin SSI power connector + 8-pin SSI 12V power connector
			(85W or below CPU only)
		PSU Connector	24-pin SSI power connector + 8-pin SSI 12V power connector +
			8-pin SSI 12V power connector
			(Support both ATX and SSI Power Supply)*1
		Management	Onboard socket for optional management card
	Onboard I/O	connector
	Connectors	USB Connectors	1 x USB 3.0 pin header (up to 2 devices)
			1 x USB 2.0 pin header (up to 2 devices)
		Fan Header	8 x 4-pin
		SMBus	1
		Chassis Intruder	1
		Front LAN LED	2
		Serial Port Header	1
		M.2 Connector	1 (NGFF Type 2242, Capacity 16 ~ 128 GB)
		External USB Port	2 x USB 3.0
			2 x USB 2.0
		VGA Port	1
	Rear I/O	SFP+	2 x 10GbE SFP+	—
	Connectors
		RJ-45	2 x GbE LAN
			1 x Management LAN
		PS/2 KB/Mouse	1
	Management	Software	ASWM Enterprise
		Out of Band
	Solution	Remote	Optional ASMB8-iKVM for KVM-over-Internet
		Management
	Monitoring	CPU Temperature
		FAN RPM

Operation temperature: 10°C ~ 35°C Environment Non operation temperature: -40°C ~ 70°C

Non operation humidity: 20% ~ 90% (Non condensing)

* Specifications are subject to change without notice. *1 Minimum requirement of ATX power supply:

•500 W

•All +12 V output ≥ 20 A

(continued on the next page)

xv

Z10PC-D8 Series specifications summary

	Model Name		Z10PC-D8/10G-2S	Z10PC-D8
			1 x Dual Port BCM57840S
	Networking	LAN	10GbE Controller	2 x Intel I210AT
			2 x Intel I210AT	1 x Management port
			1 x Management port
	Graphic	VGA	Aspeed AST2400 32MB
		TPM Header	1
			24-pin SSI power connector + 8-pin SSI 12V power connector
			(85W or below CPU only)
		PSU Connector	24-pin SSI power connector + 8-pin SSI 12V power connector +
			8-pin SSI 12V power connector
			(Support both ATX and SSI Power Supply)*1
		Management	Onboard socket for optional management card
	Onboard I/O	connector
	Connectors	USB Connectors	1 x USB 3.0 pin header (up to 2 devices)
			1 x USB 2.0 pin header (up to 2 devices)
		Fan Header	8 x 4-pin
		SMBus	1
		Chassis Intruder	1
		Front LAN LED	2
		Serial Port Header	1
		M.2 Connector	1 (NGFF Type 2242, Capacity 16 ~ 128 GB)
		External USB Port	2 x USB 3.0
			2 x USB 2.0
		VGA Port	1
	Rear I/O	SFP+	2 x 10GbE SFP+	—
	Connectors
		RJ-45	2 x GbE LAN
			1 x Management LAN
		PS/2 KB/Mouse	1
	Management	Software	ASWM Enterprise
		Out of Band
	Solution	Remote	Optional ASMB8-iKVM for KVM-over-Internet
		Management
	Monitoring	CPU Temperature
		FAN RPM

Operation temperature: 10°C ~ 35°C Environment Non operation temperature: -40°C ~ 70°C

Non operation humidity: 20% ~ 90% (Non condensing)

* Specifications are subject to change without notice. *1 Minimum requirement of ATX power supply:

•500 W

•All +12 V output ≥ 20 A

xvi

Product Introduction

1

This chapter describes the motherboard features and the new technologies it supports.

1.1Welcome!

Congratulations and thank you for buying an ASUS® Z10PC-D8 Series motherboard!

The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards!

Before you start installing the motherboard and hardware devices on it, check the items in your package with the list below.

1.2Package contents

Check your motherboard package for the following items.

			Standard Gift Box Pack	Standard Bulk Pack
	I/O Shield		1	1
	Cables	SATA 6G Cable	10	-
		COM port Cable	1	-
	Application CD	Support DVD	1	1 piece per carton
		ASWM Enterprise SDVD	1	1 piece per carton
	Packaging Quantity		1 piece per carton	10 pieces per carton

If any of the above items is damaged or missing, contact your retailer.

Optional items		Description
PIKE II 3008	LSI 8-port SAS 12G	RAID card
PIKE II 3108	LSI 8-port SAS 12G	HW RAID card
ASMB8-iKVM	Remote management solution provides KVM over IP solution
PEM-FDR	Mellanox ConnectX-3 FDR card
PEB-10G/57840-2S	Dual port 10G SFP+ Ethernet Adapter
PEB-10G/57811-1S	Single port 10G SFP+ Ethernet Adapter
PEI-10G/82599-2S	Dual port 10G SFP+ Ethernet Adapter
PEB-10G/57840-2T	Dual port 10GBase-T Ethernet Adapter

The ASUS PIKE II 3008, PIKE II 3108, PEI-10G/82599-2S, and PEM-FDR cards must be installed on PCI-E slot 5.

1-2	Chapter 1: Product Introduction

1.3Serial number label

Before requesting support from the ASUS Technical Support team, you must take note of the motherboard's serial number containing 12 characters xxS2xxxxxxxx shown in the figure below. With the correct serial number of the product, ASUS Technical Support team members can then offer a quicker and satisfying solution to your problems.

Z10PC-D8 Series	Made
	in
	China
xxS2xxxxxxxx

1.4Special features

1.4.1Product highlights

Latest Processor Technology

The motherboard supports Intel Xeon® processor E5-2600 V3 product family which provides compelling IPC increases for legacy performance improvements, floating point improvement, easier multi-core programming, and with next-generation processor power management.

Intel ® Xeon processor E5-2600 v3 product family also improve the I/O capabilities and support QPI link speed of up to 9.6GT/s.

Intel® AVX 2.0

Intel® AVX 2.0 extends 256-bit vector support for integer vector operations, doubles fixed point arithmetic throughput, adds support for new vector gather, permutes/blend, vector shifts resulting in fixed and floating-point algorithm improvements. Also, Intel's new microarchitecture doubles the cache bandwidth at L1/L2 to support higher FLOPS and contributes to greater performance in signal and image processing applications.

Next Generation of processor power management

Intel ® Xeon processor E5-2600 v3 product family enhances the processor power management with the features of Energy Efficient Turbo, Uncore Frequency Scaling, and

Per-Core P-state. Also, the Integrated Voltage Regulator enables generational performance and power improvements that the standard VR solutions cannot provide.

DDR4 memory support

The motherboard supports DDR4 memory that features faster clock frequencies and higher data transfer rates of 1333 MT/s to 2133 MT/s (million transfers per second). DDR4 offers a lower voltage standard of 1.2V that reduces memory power demand and provides improved performance.

ASUS Z10PC-D8 Series

1-3

M.2 Support

This motherboard features the M.2 slot, which shares bandwidth with the SATA 6Gb/s port and PCI-E Gen2 x1 and is dedicated to the operating system.

PCI Express 3.0

PCI Express 3.0 (PCIe 3.0) is the PCI Express bus standard that providse twice the performance and speed of PCIe 2.0. It provides an optimal graphics performance, unprecedented data speed, and seamless transition with its complete backward compatibility to PCIe 2.0 devices.

Intel® I210AT LAN Solution

The motherboard comes with two Gigabit LAN controllers and ports which provide a total solution for your networking needs. The onboard Intel® I210AT Gigabit LAN controllers use the PCI Express interface and could achieve network throughput close to Gigabit bandwidth.

Intel® C612 Series Chipset

The Intel® C612 series chipset supports with enterprise class features which is targeted for Cloud and Storage applications. It is optimized and validated to work with the latest Xeon® processor E5-2600 v3 product family, compared with the last generation, it also reduces the

TDP, supports USB 3.0 with up to 10 SATA III ports thus bringing more features and benefits to the target users.

Serial ATA III technology

The motherboard supports the Serial ATA III technology through the Serial ATA interface and Intel® C612 chipset, delivering up to 6 Gb/s data transfer rates. It also provides enhanced scalability, faster data retrieval, and double the bandwidth of current bus systems.

Temperature, fan, and voltage monitoring

The CPU temperature is monitored to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection. The chip monitors the voltage levels to ensure a stable supply of current for critical components.

1.4.2Innovative ASUS features

ASUS Fan Speed control technology

The ASUS Fan Speed control technology smartly adjusts the fan speeds according to the system loading to ensure a quiet, cool, and efficient operation.

1-4	Chapter 1: Product Introduction

Hardware Information

2

This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.

2.1Before you proceed

Take note of the following precautions before you install any motherboard component or change any motherboard settings.

• Unplug the power cord from the wall socket before touching any component.

• Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.

•Hold components by the edges to avoid touching the ICs on them.

•Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.

•Before you install or remove any component, ensure that the power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2-2	Chapter 2: Hardware Information

2.2Motherboard overview

Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

To optimize the features of your motherboard, we recommend that you install it in an ATX 2.2 compliant chassis. Please note that the form factor of this motherboard is CEB size.

Ensure to unplug the chassis power cord before installing or removing the motherboard.

Failure to do so can cause you physical injury and damage motherboard components!

2.2.1Placement direction

When installing the motherboard, ensure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.

2.2.2Screw holes

Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis.

DO NOT overtighten the screws! Doing so can damage the motherboard.

Place this side towards the rear of the chassis

ASUS Z10PC-D8 Series

2-3

2.2.3Motherboard layout

Z10PC-D8/SAS/10G-2S

2-4

Chapter 2: Hardware Information

Z10PC-D8/SAS

ASUS Z10PC-D8 Series

2-5

Z10PC-D8/10G-2S

2-6

Chapter 2: Hardware Information

Z10PC-D8

ASUS Z10PC-D8 Series

2-7

2.2.4Layout contents

Slots/Sockets		Page
1.	CPU sockets	2-10
2.	DDR4 sockets	2-15
3.	PCI Express x16 / PCI Express x8	2-19

Onboard LEDs		Page
1.	Standby Power LED (SB_PWR1)	2-22
2.	Baseboard Management Controller LED (BMC_LED1)	2-22
3.	CPU Warning LED (ERR_CPU1, ERR_CPU2)	2-23
4.	CATT LED (CATTERR_LED1)	2-23
5.	Q-Code LEDs (LED1)	2-24

Jumpers		Page
1.	Clear RTC RAM (CLRTC1)	2-27
2.	VGA controller setting (3-pin VGA_SW1)	2-28
3.	LAN controller setting (3-pin LAN_SW1, LAN_SW2)	2-28
4.	ME firmware force recovery setting (3-pin ME_RCVR1)	2-29
5.	DDR4 thermal event setting (3-pin DIMMTRIP1)	2-29
6.	RAID configuration utility selection (3-pin RAID_SEL1)	2-30
7.	PMBus 1.2 PSU select jumper (3-pin SMART_PSU1)	2-30

2-8	Chapter 2: Hardware Information

Internal connectors		Page
1.	Serial ATA 6.0 Gbps connectors (7-pin SATA1, SATA2, SATA3, SATA4,
	SATA5, SATA6 [Light Blue]) (7-pin SSATA1, SSATA2, SSATA3 [Gray],	2-33
	SSATA4 [Light Gray])
2.	M.2 (NGFF) connector (NGFF1)	2-34
3.	Power Supply SMBus connector (5-pin PSUSMB1)	2-34
4.	USB 2.0 connector (10-1 pin USB34)	2-35
5.	USB 3.0 connector (20-1 pin USB3_34)	2-35
6.	CPU, front, and rear fan connectors (4-pin CPU_FAN1, CPU_FAN2,
	FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4, FRNT_FAN5,	2-36
	REAR_FAN1, REAR_FAN2)
7.	Serial port connector (10-1 pin COM1)	2-36
8.	Trusted Platform Module connector (20-1 pin TPM1)	2-37
9.	EATX power connectors (24-pin EATXPWR1, 8-pin EATX12V1, 8-pin	2-38
	EATX12V2)
10.	System panel connector (20-1 pin PANEL1)	2-39
11.	Auxiliary panel connector (20-2 pin AUX_PANEL1)	2-40
12.	Hard disk activity LED connector (4-pin HDLED1)	2-41
13.	Chassis Intrusion connector (2-pin INTRUSION1)	2-41
14.	Mini-SAS connectors (ISAS1~2)	2-42
15.	SFP+ 1 2 LED connectors (5-1 pin LAN34_LED1)	2-42

ASUS Z10PC-D8 Series

2-9

2.3Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA 2011-3 Socket designed for the Intel® Xeon E5-2600 v3 processor family.

•Upon purchase of the motherboard, ensure that the PnP cap is on the socket and

the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related.

•Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA

2011-3 socket.

•The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.

2.3.1Installing the CPU

To install a CPU:

1.Locate the CPU socket on the motherboard.

Before installing the CPU, ensure that the socket box is facing toward you and the triangle mark is on the top-right position.

Triangle mark

2-10	Chapter 2: Hardware Information