Yamaha RX-V2200 User Manual

RX-V2200

AV Receiver

U

OWNER’S MANUAL

IMPORTANT

Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.

SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel
under the following conditions:

a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

I CAUTION

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the
manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

Note to CATV system installer:

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.

SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection
to grounding electrodes, and requirements for the
grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)

GROUNDING CONDUCTORS
(NEC SECTION 810–21)

GROUND CLAMPS

ELECTRIC
SERVICE
EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

MAST

GROUND
CLAMP

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!

This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.

2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:

Relocate either this product or the device that is being
affected by the interference.

Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.

CAUTION II

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future
reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the
right and left, and 10 cm at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a
room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal
injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may

cause fire, damage to this unit, and/or personal
injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or
damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than
specified is dangerous and may cause fire,
damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any
damage resulting from use of this unit with a
voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an
electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding
that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.

III CAUTION

Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.

INTRODUCTION

CONTENTS

INTRODUCTION

CONTENTS ....................................................... 1

FEATURES ........................................................ 2

GETTING STARTED ....................................... 3

Checking the Package Contents ............................... 3

Installing Batteries in the Remote Control ............... 3

CONTROLS AND FUNCTIONS .................... 4

Front Panel ............................................................... 4

Remote Control ........................................................ 6

Using the Remote Control ........................................ 7

Front Panel Display .................................................. 8

Rear Panel ................................................................ 9

PREPARATION

SPEAKER SETUP .......................................... 10

Speakers to Be Used ............................................... 10

Speaker Placement ................................................. 10

Connecting the Speakers ........................................ 11

CONNECTIONS ............................................. 14

Before Connecting Components ............................ 14

Connecting Video Components .............................. 14

Connecting Audio Components ............................. 16

Connecting to an External Amplifier ..................... 18

Connecting an External Decoder ............................ 18

Connecting the Power Supply Cords...................... 19

Turning on the Power ............................................. 20

ON-SCREEN DISPLAY (OSD) ..................... 21

OSD Modes ............................................................ 21

Selecting the OSD Mode ........................................ 21

SPEAKER MODE SETTINGS ..................... 22

Summary of SPEAKER SET Items 1A through 1F ...

ADJUSTING THE SPEAKER OUTPUT

LEVELS ....................................................... 23

Before You Begin ................................................... 23

Using the Test Tone (TEST DOLBY SUR.) .......... 23

BASIC OPERATION

BASIC PLAYBACK ........................................ 25

Input Modes and Indications .................................. 27

Selecting a Sound Field Program ........................... 28

Selecting PRO LOGIC or Neo: 6 ....................... 29

DIGITAL SOUND FIELD PROCESSING

(DSP) ............................................................ 31

Understanding Sound Fields .................................. 31

Hi-Fi DSP Programs............................................... 31

CINEMA-DSP ................................................. 32

Sound Design of CINEMA-DSP ............................ 32

CINEMA-DSP Programs ....................................... 34

TUNING ........................................................... 36

Connecting the Antennas........................................ 36

Automatic and Manual Tuning............................... 37

Presetting Stations .................................................. 38

Tuning in to a Preset Station .................................. 40

Exchanging Preset Stations .................................... 40

BASIC RECORDING ..................................... 41

ADVANCED OPERATION

INTRODUCTION

REMOTE CONTROL FEATURES .............. 42

Control Area ........................................................... 42

Setting the Manufacturer Code .............................. 43
Programming a New Remote Control Function

(Learn Feature) ................................................... 44

Using the Macro Feature ........................................ 45
Changing the Source Name in the Display Window

............................................................................ 47

Clearing Learned Functions, Macros, Renamed

Source Names, and Setup Manufacturer Codes ...

Clearing a Learned Function or Macro .................. 48

Each Component Control Area .............................. 50

47

PREPARATION

SET MENU ...................................................... 55

Adjusting the Items on the SET MENU................. 55

1 SPEAKER SET (speaker mode settings) ........... 56

2 LOW FRQ TEST ............................................... 59
3 L/R BALANCE (balance of the left and right main

speakers)............................................................. 60

4 HP TONE CTRL (headphone tone control) ....... 60

5 CENTER GEQ (center graphic equalizer) ......... 60

6 INPUT RENAME .............................................. 61

7 I/O ASSIGNMENT ............................................ 61

8 INPUT MODE (initial input mode) ................... 62

9 PARAM. INI (parameter initialization) ............. 63

10 LFE LEVEL ..................................................... 63

11 DYNAMIC RANGE ......................................... 64

12 SP DELAY TIME ............................................. 64

13 DISPLAY SET.................................................. 65

14 MEMORY GUARD ......................................... 65

OPERATION

BASIC

OPERATION

ADVANCED

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS .................................................. 66

22

SLEEP TIMER ................................................ 67

Setting the Sleep Timer .......................................... 67

Canceling the Sleep Timer ..................................... 67

ZONE 2 ............................................................ 68

Zone 2 Connections ................................................ 68

Remote Control in Zone 2 ...................................... 69

INFORMATION

ADDITIONAL

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING ..................................................... 70

What is a sound field? ............................................ 70

Sound Field Program Parameters ........................... 70

Changing Parameter Settings ................................. 71

Resetting a Parameter to the Factory-set Value ...... 71

DIGITAL SOUND FIELD PARAMETER

DESCRIPTIONS ......................................... 72

TROUBLESHOOTING.................................. 76

GLOSSARY ..................................................... 81

SPECIFICATIONS ......................................... 83

English

1

FEATURES

Built-in 6-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz, 8Ω)
Main: 100 W + 100 W
Center: 100 W
Rear: 100 W + 100 W
Rear center: 100 W

Multi-Mode Digital Sound Field
Processing

◆ Dolby Pro Logic/Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital Matrix 6.1 Decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS

Neo: 6 Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital
or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 14 Items

for Optimizing This Unit for Your Audio/Video
System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Capability

◆ PROCESSOR DIRECT for no alteration of the

original signal

◆ Custom Installation Facility

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this
manual.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.

“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are
trademarks of Digital Theater System, Inc.

2

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Remote control

CLEAR LEARN MACRO

A

STANDBY

MD/TAPE

TUNER

VCR 1

CBL/SAT

TITLE

MENU

DISPLAY

SEARCH

REC

HALL 2

HALL 1

234

1

ROCK

ENTER-

CONCERT

TAINMENT

596

MOVIE

MOVIE

THEATER 1

THEATER 2

10

010100

PRESET

CH

DISC

B

CD-R

VCR2/DVR

ENTER

CHAPTER

– +

PAUSESTOPPOWER

CHURCH

TV

SPORTS

78

/DTS

SUR.

11 12

+

MUTE

STEREO

EFFECT

VOLUME

PARAMETER

MACRO

OFF ON

PHONO

6CH INPUT

JAZZ CLUB

SET MENU

CD

DVD

SOUND

PLAY

MONO
MOVIE

SELECT

+

POWER

D-TV/LD

10KEY

ON SCREEN

TRANSMIT

RE-NAME

SYSTEM

V-AUX

SOURCE

SELECT

DSP

6.1/ES

CHP/INDEX

A/B/C/D/E

TV INPUT

TV VOL

TV MUTE

LEVEL

TESTSLEEP

Batteries (3) (R6)

Indoor FM antenna
(U.S.A., Canada, China and
General models)

Indoor FM antenna
(Australia model)

Connection GuideAM loop antenna

DVD Player Main Speaker

AUDIO OUT S VIDEO

VIDEO

COMPONENT

OPTICAL

OUT

OUT

VIDEO OUT

IN

Analog audio signal

Optical digital signal

S video signal

Video signal

Signal flow

LR

S VIDEO

AUDIO

OPTICAL

VIDEO

OUT

OUT

IN

OUT

L RSV

O

COMPONENT VIDEO

AUDIO AUDIO VIDEO

DIGITAL OUTPUT

S VIDEO

VIDEO

R

R

L

L

OPTICAL

PR/ C

DVD

MD

/

IN

DVD

TAPE

(

)

PLAY

MD/TAPE

D-TV / LD

OUT

D-TV

(

)

CD-R

REC

/LD

MONITOR
OUT

CBL

IN

CD

/SAT

(

)

PLAY

CD-R

OUT
(

)

IN

REC

CD-R

VCR 1

OUT

DVD

CD

D-TV

IN

PHONO

/LD

VCR 2
/DVR

OUT

MAIN

CD

CBL

SURROUND

/SAT

COAXIAL

MONITOR OUT

SUB

VIDEO

S VIDEO

WOOFER

CENTER

GND

DIGITAL INPUT

6CH INPUT

V

S

S VIDEO IN VIDEO IN

COMPONENT
VIDEO IN

TV Subwoofer Center Speaker Rear Center

RIGHT LEFT

COMPONENT
VIDEO OUT

R

PB/ CB Y

SUB
WOOFER

MAIN

TUNER

R

LRL

+

+

AM
ANT

REAR

A

(SURROUND)

GND

–

–

75Ω UNBAL.

FM

–

–

ANT

REAR

CENTER

B

CENTER

+

+

SPEAKERS

LEFT

Rear Speaker

Speaker

CONNECTION
GUIDE

L

R

O

S

V

V795390

Power Cord
(U.S.A., and Canada models
only)

INTRODUCTION PREPARATION

RIGHT

OPERAIONT

BASIC

Installing Batteries in the Remote Control

RESET button

1 Open the battery compartment cover.
2 Insert three supplied batteries (R6) in the

correct direction by aligning the + and –
marks on the batteries with the polarity
markings (+ and –) on the inside of the
battery compartment.

3 After new batteries are correctly inserted,

press the RESET button in the battery
compartment using a ball point pen or
similar object. (This does not clear the
contents of the memory.)

4 Replace the cover as pressing until it snaps

into place.

■ Notes on batteries

• Change all of the batteries if you notice the condition
like; the operating range of the remote control
decreases, the indicator does not flash or its light
becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.

• If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing
new batteries.

If the remote control is without batteries for more than
3 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

3

CONTROLS AND FUNCTIONS

Front Panel

123 4567

NATURAL SOUND AV RECEIVER

STANDBY

/

ON

PROCESSOR

SPEAKERS

AB

BASS

DIRECT

EXTENSION

90 qw

8

CBL/SAT

D-TV/LD

VCR1

VCR2
/DVR

V-AUX

REC OUT/ZONE 2

SOURCE
/REMOTE

DVD

MD/TAPE

CD-R

TUNER

CD

PHONO

A/B/C/D/E

STEREO

EFFECT

e

PRESET
TUNING

PROGRAM

r

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.

Standby mode

In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this
unit (see page 8).

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,
DTS, ANALOG) to receive when one component is
connected to two or more input jacks of this unit (see
page 27). Priority cannot be set when 6CH INPUT is
selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

INPUT M0DE

DIGITAL

PRO LOGIC

/

PRESET

/TUNING

EDIT

PHONES

SILENT

t

MEMORY

FM/AM

MAN'L/AUTO FM AUTO/MAN'L MONO

S VIDEO

u

y

TUNING

MODE

VIDEO AUDIO OPTICALLR

VIDEO AUX

PRESET
/TUNING

EDIT

FM/AM

o

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

p

ai

VOLUMEINPUT

BASS

–+

s

6 VOLUME

Controls the output level of all audio channels.
This does not affect the REC OUT level.

7 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons on the remote control).

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel at each time its
corresponding button is pressed.

9 BASS EXTENSION

Turns on or off the BASS EXTENSION function at each
time the button is pressed, this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if “1B MAIN
SP” on the SET MENU is set to SMALL and “1E LFE/
BASS OUT” is set to SWFR.

0 PROCESSOR DIRECT

Turns on or off the PROCESSOR DIRECT function at
each time the button is pressed. When this is on, BASS,
TREBLE, and BASS EXTENSION are bypassed,
eliminating any alteration of the original signal.

6CH INPUT

TREBLE

–+

d

4

CONTROLS AND FUNCTIONS

q REC OUT/ZONE 2

Selects the source you want to direct to the audio/video
recorder and ZONE 2 outputs independent of the source
you are listening to in the main room. When set to the
SOURCE/REMOTE position, the input source is directed
to all outputs.

w STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.
When STEREO is selected, 2-channel input signals are
directed to the main left and right speakers without effect
sounds. All Dolby Digital and DTS audio signals except
for the LFE channel are mixed down to the main left and
right speakers.

e A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

r PROGRAM l / h

Selects the DSP program (see page 28).

t PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.

y PHONES jack

Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.

u VIDEO AUX jacks

Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.

a TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the “AU TO” indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the “AUTO ” indicator does not light up.

s BASS

Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.

d TREBLE

Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the left and
right main speakers.

■ Opening and closing the front

panel door

When you are not operating the controls behind the front
panel door, close the door.

D

I
G

I
T

A

L

INTRODUCTION PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

i PRESET/TUNING EDIT

Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset
station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.

o FM/AM

Switches the reception band between FM and AM.

p MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.

To open, press gently on the lower part of the panel.

5

INFORMATION

ADDITIONAL

APPENDIX

English

CONTROLS AND FUNCTIONS

Remote Control

This section describes the controls and their functions of
the remote control. See “REMOTE CONTROL
FEATURES” on pages 42 to 54 for operating other
components with this remote control.

1
2

3
4

5

6

7

9

q
w

e

8

0

TRANSMIT

SYSTEM

POWER

V-AU X

D-TV/LD

SOURCE

SELECT

10KEY

6.1/ES

CHP/INDEX

TV VOL

ON SCREEN

RE-NAME

DSP

A/B/C/D/E

TV INPUT

TV MUTE

LEVEL

TESTSLEEP

CLEAR LEARN MACRO

A

STANDBY

MD/TAPE

TUNER

VCR 1

CBL/SAT

TITLE

MENU

DISPLAY

SEARCH

REC

HALL 2

HALL 1

1

234

ROCK

ENTER-

CONCERT

TAINMENT

596

MOVIE

MOVIE

THEATER 1

THEATER 2

10

0

PRESET

MUTE

CH

STEREO

DISC

EFFECT

MACRO

OFF ON

B

PHONO

CD

CD-R

VCR2/DVR

DVD

6CH INPUT

ENTER

SOUND

CHAPTER

– +

PAUSESTOPPOWER

PLAY

CHURCH

JAZZ CLUB

TV

MONO

SPORTS

MOVIE

78

/DTS

SUR.

SELECT

11 12

+

+

10

100

VOLUME

PARAMETER

SET MENU

t
y
u

i
o
p

a

s

d

f

g

h
j

r

3 TRANSMIT indicator

Flashes while the remote control is sending signals.

4 STANDBY

Sets this unit in the standby mode.

5 SYSTEM POWER

Turns on the power of this unit.

6 Display window

Shows the selected source component that you are
controlling.

7 SOURCE SELECT k/n

Selects the another component to control independently
from the input that has been selected by pressing an input
selector button.

8 10KEY/DSP

Selects the numeric button (10KEY) mode or DSP mode.

9 Operation buttons

Provides functions such as play, stop, skip, etc. for
operating your other components selected by the input
selector buttons.

0 6.1/ES

Turns on or off the Dolby Digital Matrix 6.1 or DST ES
decoder with 10 KEY/DSP set to the DSP position.

q LEVEL

Selects the effect speaker channel to be adjusted and sets
the level.

w ON SCREEN

Selects the on-screen display (OSD) mode for your video
monitor.

e SLEEP

Sets the sleep timer.

r TEST

Outputs the test tone to adjust the speaker levels.

1 Infrared window

Outputs infrared control signals. Aim this window at the
component you want to operate.

2 RE-NAME

Used for changing the input source name in the display
window (see page 47).

6

t CLEAR

Used for clearing functions acquired when using the learn
and rename features, and set manufacturer codes (see
page 47).

y LEARN

Used for setting up the manufacturer code or for
programming the functions of other remote controls (see
pages 43 and 44).

CONTROLS AND FUNCTIONS

u MACRO

Used to program a series of operations for control by a
single button (see page 46).

i MACRO ON/OFF

Turns the macro function on and off.

o Å and ı

Switch the control area for the extra components that are
not connected to this unit without changing the input.

p Input selector buttons

Select the input source and change the control area.

a 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

s DSP program/Numeric buttons

Select DSP programs or numbers according to the
position of 10KEY/DSP.

d MUTE

Mutes the sound. The MUTE indicator turns on when the
MUTE function is on. Press again to restore the audio
output to the previous volume level.

f VOLUME +/–

Increases or decreases the volume level.

g STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.
When STEREO is selected, 2-channel input signals are
directed to the main left and right speakers without effect
sounds. All Dolby Digital and DTS audio signals except
for the LFE channel are also directed to the main left and
right speakers.

Using the Remote Control

VOLUMEINPUT

INPUT M0DE

DIGITAL

/

TUNING

PRESET

MEMORY

FM/AM

MODE

/TUNING

EDIT

MAN'L/AUTO FM AUTO/MAN'L MONO

PHONES

S VIDEO

VIDEO AUDIO OPTICALLR

VIDEO AUXSILENT

Approximately 6 m (20 feet)

SPEAKERS

AB

STANDBY

/

ON

NATURAL SOUND AV RECEIVER

PROCESSOR

BASS

DIRECT

EXTENSION

SOURCE

PRESET

/REMOTE

TUNING

A/B/C/D/E

DVD

MD/TAPE

CD-R

D-TV/LD

TUNER

CBL/SAT

VCR1

CD

STEREO

PROGRAM

VCR2

PHONO

/DVR

V-AUX

EFFECT

REC OUT/ZONE 2

30°30°

The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote
control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:
– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or
– in places subject to extremely low temperatures.

6CH INPUT

PRO LOGIC

BASS

TREBLE

– +

– +

INTRODUCTION PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

h PARAMETER/SET MENU

Selects the PARAMETER mode or SET MENU mode.

j Cursor buttons k/n/–/+

Select and adjust DSP program parameters and SET
MENU items according to the position of PARAMETER/
SET MENU.

INFORMATION

ADDITIONAL

APPENDIX

English

7

CONTROLS AND FUNCTIONS

Front Panel Display

123456

VCR DVD TUNER CD

/

1

VIRTUAL

SILENT

SP

AB

90

CBL/SAT

VCR2/DVR

DSP

6.1/ES

PCM

DISCRETE

DIGITAL

PRO LOGIC

78 q wertyui

TV/LD

D

DTS Neo

:6 DOLBY DIGITAL PRO LOGIC

MOVIE THEATER

MD/TAPE

ENTERTAINMENT12

1 Processor indicators

When any function of DSP, DTS, DISCRETE,

/

PRO LOGIC

VIRTUAL, g, 6.1/ES, and
activated, its indicator lights up.

is

CD RV AUX

AUTO

STEREO

MEMORY

TUNED

q DSP program indicators

The name of the selected DSP program lights up when
the ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or V/DTS SURROUND DSP program is

PHONO

MUTE VOLUME

SLEEP

BASS

P. DIRECT

LCR

RL

LFE

RC RR

selected.

2 Input source indicator

Shows the current input source with underneath.

3 AUTO indicator

Shows that this unit is in the automatic tuning mode.

w Multi-information display

Shows the current DSP program name and other
information when adjusting or changing settings.

e STEREO indicator

4 SLEEP indicator

Lights up while the sleep timer is on.

5 MUTE indicator

Lights up while the MUTE function is on.

6 VOLUME level indicator

Indicates the volume level.

7 v indicator

Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.

Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the “AUTO” indicator is lit.

r TUNED indicator

Lights up when this unit tunes in to a station.

t MEMORY indicator

Flashes to show a station can be stored.

y BASS indicator

Lights up while BASS EXTENSION is on.

u P. DIRECT

8 Headphones indicator

Lights up when headphones are connected.

Lights up while PROCESSOR DIRECT is on.

i Input channel indicator

9 SP A B indicator

Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.

Indicates the channel components of input signals being
received.

0 SILENT indicator

Lights up when headphones are connected with the sound
effect (see “SILENT CINEMA DSP” on page 30).

8

Rear Panel

CONTROLS AND FUNCTIONS

DVD

D-TV

CBL
/SAT

VCR 1

OUT

VCR 2
/DVR

OUT

/LD

IN

IN

ZONE 2 OUT

S VIDEO

S VIDEO

3

VIDEO

VIDEO

COMPONENT VIDEO

PR/ C

R

PB/ CB Y

DVD

D-TV / LD

MONITOR

OUT

TUNER

AM

ANT

GND

75Ω UNBAL.

FM

ANT

CONTROL OUT SPEAKERS

1

DIGITAL OUTPUT

OPTICAL

COAXIAL

DIGITAL INPUT

8

2

AUDIO AUDIO VIDEO

SUB

WOOFER

R

L

L

MONITOR OUT

R

MD

/

IN

TAPE

(

)

PLAY

MD/TAPE

OUT
(

)

CD-R

REC

IN

CD

(

)

PLAY

CD-R

OUT
(

)

REC

CD-R

DVD

CD

D-TV

PHONO

/LD

MAIN

CD

CBL

SURROUND

/SAT

CENTER

GND

6CH INPUT

9 0 w e rq

1 DIGITAL OUTPUT jacks

2 Audio component jacks

See pages 16 and 17 for connection information.

3 Video component jacks

See pages 14 and 15 for connection information.

4 REMOTE IN/OUT jacks

See page 68 details.

5 OUTPUT jacks

See page 18 for connection information.

6 AC INLET (U.S.A. and Canada models only)

Use this inlet to plug in the supplied power cord.

*1

4

10mA

REMOTE

5

OUTPUT

L

R

MAIN

SUB

WOOFER

MAIN

R

L

+

A

–

IN

–

OUT

+12V

MAX.

B

+

REAR

(SURROUND)

CENTER

REAR

(SURROUND)

CENTER

L

R

R

REAR

CENTER

+

–

–

+

IMPEDANCE SELECTOR

SET BEFORE POWER ON

L

MAIN A OR B:

CENTER
REAR CENTER
REAR

MAIN A OR B:

CENTER
REAR CENTER
REAR

REAR

CENTER

4ΩMIN. /SPEAKER

A+B:

8ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

A+B:

16ΩMIN. /SPEAKER

:
:
:

6

8ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER
8ΩMIN. /SPEAKER
8ΩMIN. /SPEAKER

q Antenna input terminals

See page 36 for connection information.

w CONTROL OUT

This is a control expansion terminal for commercial use.

e Speaker terminals

See pages 11 and 12 for connection information.

r IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your
speaker impedance (see page 13). Set this unit in the
standby mode before you change the setting of this
switch.

7

AC IN

AC OUTLETS

(U.S.A. model)

INTRODUCTION PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

7 AC OUTLET(S)

Use these outlets to supply power to your other A/V
components (see page 19).

8 DIGITAL INPUT jacks

9 6CH INPUT jacks

See page 18 for connection information.

0 ZONE 2 OUT jacks

See page 68 for details.

< China and General models only >

FREQUENCY STEP switch

See page 36.

VOLTAGE SELECTOR

See page 19.

*1 As this terminal is used for an examination in the factory, do not

connect any equipment to this terminal.

APPENDIX

English

9

PREPARATION

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best sound­field quality with a 6-speaker system, using left and right
main speakers, left and right rear speakers, and a center
and rear center speakers. If you use different brands of
speakers (with different tonal qualities) in your system,
the tone of a moving human voice and other types of
sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.

The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.

The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use the
models of equivalent performance with the main
speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.

Speaker Placement

Refer to the following diagram when you place the
speakers.

Main speaker (R)Center speaker

Rear speaker (R)

Subwoofer

Main
speaker (L)

■ Main speakers

Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.

■ Center speaker

Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
“1A CENTER SP” on the SET MENU is set to NONE (see
page 56 for details).

■ Rear speakers

Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (6 feet) above the
floor.

■ Rear center speaker

Place the rear center speaker in the center between the left
and right rear speakers at the same height from the floor
as the rear speakers.

1.8 m (6 feet)

Rear center
speaker

Rear speaker (L)

10

■ Subwoofer

The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.

CAUTION

Use magnetically shielded speakers. If this type of
speakers still creates the interference with a monitor,
place the speakers away from the monitor.

Connecting the Speakers

SPEAKER SETUP

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or

10 mm (3/8”)

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

12

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

Red: positive (+)
Black: negative (–)

2

3

1

1 Unscrew the knob.
2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

OPERATION

ADVANCED

Banana plug

y

(U.S.A., Canada, Australia, China and General models only)

• Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

11

INFORMATION

ADDITIONAL

APPENDIX

English

SPEAKER SETUP

DIGITAL OUTPUT

OPTICAL

COAXIAL

DIGITAL INPUT

(U.S.A. model)

AUDIO AUDIO VIDEO

R

MD

/

IN

TAPE

(

)

PLAY

MD/TAPE

OUT
(

)

CD-R

REC

IN

CD

(

)

PLAY

CD-R

OUT
(

)

REC

CD-R

DVD

CD

D-TV

PHONO

/LD

MAIN

CD

CBL

SURROUND

/SAT

CENTER

GND

6CH INPUT

WOOFER

L

SUB

Main B speaker

Right Left

S VIDEO

R

L

DVD

D-TV

/LD

CBL
/SAT

IN

VCR 1

OUT

IN

VCR 2
/DVR

OUT

ZONE 2 OUT

MONITOR OUT

S VIDEO

VIDEO

VIDEO

Main A speaker

Right Left

1

COMPONENT VIDEO

PR/ C

R

PB/ CB Y

DVD

D-TV / LD

MONITOR

OUT

TUNER

REMOTE

AM
ANT

GND

75Ω UNBAL.

FM

ANT

OUT

+12V

10mA

MAX.

CONTROL OUT SPEAKERS

Subwoofer

system

23

OUTPUT

L

R

MAIN

SUB

WOOFER

MAIN

R

IN

L

+

A

–

–

B

+

REAR

(SURROUND)

CENTER

REAR

(SURROUND)

CENTER

L

R

R

REAR
CENTER

+

–

–

+

IMPEDANCE SELECTOR

SET BEFORE POWER ON

L

MAIN A OR B:

4ΩMIN. /SPEAKER

A+B:

8ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

6ΩMIN. /SPEAKER

:

REAR

6ΩMIN. /SPEAKER

MAIN A OR B:

8ΩMIN. /SPEAKER

A+B:

16ΩMIN. /SPEAKER

:

8ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

8ΩMIN. /SPEAKER

:

REAR

8ΩMIN. /SPEAKER

REAR

CENTER

AC IN

AC OUTLETS

4567

Center

speaker

Rear Center

speaker

Right

Rear speaker

Left

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,
connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or
rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The
LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are
assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level by using the
remote control of this unit (see ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS on page 66).

• Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from
the SUBWOOFER jack.

1

4

2

3

6

5

7

The diagram above shows the speaker layout in the
listening room.

12

SPEAKER SETUP

■ IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.

Select the left and right position according to the impedance of the speakers in your system. Be sure to move this switch
only when this unit is in the standby mode.

IMPEDANCE
SELECTOR
switch

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

4ΩMIN. /SPEAKER

A+B:

8ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

6ΩMIN. /SPEAKER

:

REAR

6ΩMIN. /SPEAKER

MAIN A OR B:

8ΩMIN. /SPEAKER

A+B:

16ΩMIN. /SPEAKER

:

8ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

8ΩMIN. /SPEAKER

:

REAR

8ΩMIN. /SPEAKER

Switch

position

Left

Speaker

Main

Center

Rear

Center

Impedance level

If you use one set of main speakers, the impedance of
each speaker must be 4 Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 8 Ω or higher.

The impedance must be 6 Ω or higher.

The impedance must be 6 Ω or higher.

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

4ΩMIN. /SPEAKER

A+B:

8ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

6ΩMIN. /SPEAKER

:

REAR

6ΩMIN. /SPEAKER

MAIN A OR B:

8ΩMIN. /SPEAKER

A+B:

16ΩMIN. /SPEAKER

:

8ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

8ΩMIN. /SPEAKER

:

REAR

8ΩMIN. /SPEAKER

(U.S.A. model)

AC IN

AC OUTLETS

Right

Rear

Main

Center

Rear

Center

Rear

The impedance of each speaker must be 6 Ω or higher.

If you use one set of main speakers, the impedance of
each speaker must be 8 Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16 Ω or higher.
[Canada model only]
The impedance of each speaker must be 8 Ω or higher.

The impedance must be 8 Ω or higher.

The impedance must be 8 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

13

English

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been
completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.

• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling
system to all its products.

• After you have completed all connections, check them again to make sure they are correct.

Connecting Video Components

■ About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (P
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, CB, CR/Y, PB, PR/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.

, PR/CR) video signals. The jacks are also separated

B/CB

If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.

VIDEO

S VIDEO VIDEO

S VIDEO
jack

VIDEO jack
(composite)

COMPONENT VIDEO

PR/ CR PB/ CB Y

COMPONENT
VIDEO jacks

y

• Each type of video jack works independently. Signals input through the composite
video, S-video and component jacks are output through the corresponding composite
video, S-video, and component jacks, respectively.

• You can designate the input for the COMPONENT VIDEO A and B jacks according
to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see pages
61 and 62 for details).

Notes

• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being
connected.

■ VIDEO AUX jacks (on the front panel)

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

S

VLR

O

OPTICAL OUT

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

S VIDEO OUT

Game console or camcorder

These jacks are used to connect any video input source
such as a game console and a camcorder to this unit.

14

AUDIO
OUTPUT

OPTICAL
OUTPUT

TV/digital TV or

LD player

RF
OUTPUT

LD player

COMPONENT
OUTPUT

AUDIO
OUTPUT

OPTICAL
OUTPUT

DVD player

CONNECTIONS

COMPONENT
OUTPUT

INTRODUCTION

RF
INPUT

RF
demodulator

L

R

O

O

C

C

L

R

S VIDEO
OUTPUT

*1

S VIDEO
OUTPUT

AUDIO
OUTPUT

S

DIGITAL OUTPUT

OPTICAL

MD
TAPE

CD-R

CD-R

DVD

D-TV

/SAT

COAXIAL

DIGITAL INPUT

S

VIDEO
OUTPUT

Cable TV or

Satellite tuner

VIDEO

V

OUTPUT

/

IN

(

PLAY

MD/TAPE

OUT
(

REC

IN

CD

(

PLAY

CD-R

OUT
(

REC

CD

PHONO

/LD

MAIN

CD

CBL

SURROUND

GND

)

)

)

)

CENTER

AUDIO

R

WOOFER

6CH INPUT

V

L

SUB

R

R

L

L

AUDIO VIDEO

S VIDEO

L

DVD

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2
/DVR

OUT

ZONE 2 OUT

MONITOR OUT

S VIDEO

R

L

S VIDEO
OUTPUT

R

S VIDEO
OUTPUT

VIDEO

VIDEO

S

S

COMPONENT VIDEO

PR/ C

R

PB/ CB Y

DVD

D-TV / LD

MONITOR

OUT

TUNER

AM

ANT

GND

75Ω UNBAL.

FM

ANT

CONTROL OUT

S

S VIDEO
INPUT

V

VIDEO
OUTPUT

VCR 1 or VCR 2/

DVR (digital

video recorder)

VIDEO

V

OUTPUT

REMOTE

10mA

MAX.

OUT

+12V

MAIN

(U.S.A. model)

SUB

WOOFER

MAIN

R

IN

V

VIDEO
INPUT

PREPARATION

L

R

L

+

A

–

–

B

+

BASIC OPERA-

TION

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

COAXIAL
OUTPUT

indicates signal direction

L

indicates left analog cables

R

indicates right analog cables

O

indicates optical cables

C

indicates coaxial cables

V

indicates video cables

S

indicates S-video cables

AUDIO INPUT

AUDIO OUTPUT

*1 If your LD player has an RF

OUTPUT jack, first connect it to
the RF INPUT on an RF
demodulator and then connect
the RF OUTPUT on an RF
demodulator to the COAXIAL
jack on this unit.

VIDEO
INPUT

Video monitor

V

S VIDEO
INPUT

S

COMPONENT
INPUT

APPENDIX

English

15

CONNECTIONS

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals (see page 27 for details).

y

• You can designate the input for each digital jacks according to
your component by using “7 I/O ASSIGNMENT” on the SET
MENU (see pages 61 and 62 for details).

Note

• The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an in-line boosting
transformer or MC-head amplifier when connecting to
these jacks.

y

• Connect your turntable to the GND terminal to reduce noise in
the signal. However you may hear less noise without the
connection to the GND terminal for some record players.

■ Connecting a CD player

y

• The COAXIAL CD and OPTICAL CD jacks are available for a
CD player which has coaxial or optical digital output jacks.

• When you connect a CD player to both the COAXIAL CD and
OPTICAL CD jacks, priority is given to the input signals from
the COAXIAL CD jack.

■ Connecting an MD recorder, tape

deck or CD recorder

y

• DIGITAL OUTPUT jacks and analog OUT (REC) are
independent. Only digital signals are output from DIGITAL
OUTPUT jacks and analog signals from OUT (REC) jacks.

• When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.

Notes

• When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit may
distort the sound from other components.

• When you record from a source component connected to this
unit while this unit is set in the standby mode, the recorded
sound may be distorted. To avoid this problem, turn on this
unit.

16

CONNECTIONS

OPTICAL
OUTPUT

CD player

COAXIAL
OUTPUT

OPTICAL
INPUT

MD recorder or

tape deck

INPUT OUTPUT INPUTOUTPUT

L

OUTPUT

(U.S.A. model)

R

O

O

L

R

C

R

L

DIGITAL OUTPUT

OPTICAL

MD

/

TAPE

MD/TAPE

CD-R

CD

CD-R

CD-R

DVD

CD

D-TV

PHONO

/LD

MAIN

CD

CBL

SURROUND

/SAT

COAXIAL

DIGITAL INPUT

GND

O

AUDIO

R

L

IN

(

)

PLAY

OUT
(

)

REC

IN

(

)

PLAY

OUT
(

)

REC

SUB

WOOFER

CENTER

6CH INPUT

OPTICAL
INPUT

AUDIO VIDEO

R

L

DVD

D-TV

CBL
/SAT

VCR 1

OUT

VCR 2
/DVR

OUT

MONITOR OUT

S VIDEO

/LD

IN

IN

ZONE 2 OUT

S VIDEO

CD recorder

R

L

VIDEO

DVD

D-TV / LD

MONITOR

VIDEO

L

COMPONENT VIDEO

PR/ C

R

OUT

R

PB/ CB Y

TUNER

AM

ANT

GND

75Ω UNBAL.

FM

ANT

CONTROL OUT

OPTICAL
OUTPUT

REMOTE

IN

OUT

+12V

10mA

MAX.

INTRODUCTION

PREPARATION

O

BASIC OPERA-

TION

GND

OUTPUT

Turntable

indicates signal direction

L

indicates left analog cables

R

indicates right analog cables

O

indicates optical cables

C

indicates coaxial cables

L R

CENTER
OUTPUT

SUBWOOFER
OUTPUT

L R

SURROUND
OUTPUT

External decoder

See page 18

L R

MAIN
OUTPUT

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

17

CONNECTIONS

Connecting to an External Amplifier

If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for
output to an external amplifier, it is not necessary to use the
corresponding SPEAKERS terminals.

12

OUTPUT

MAIN

SUB

WOOFER

REAR

(SURROUND)

CENTER

L

R

3

1 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the
BASS, TREBLE and BASS EXTENSION settings.

2 REAR (SURROUND) jacks

Rear channel line output jacks.

R

4 5

L

REAR

CENTER

Connecting an External Decoder

This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, settings of
“1 SPEAKER SET” on the SET MENU do not apply (except

for 1F MAIN LEVEL).

3 SUBWOOFER jack

When using a subwoofer with built-in amplifier, including
the YAMAHA Active Servo Processing Subwoofer
System, connect the input jack of the subwoofer system
to this jack. Low bass signals distributed from the main,
center and/or rear channels are directed to this jack if they
are assigned to this jack. (The cut-off frequency of this
jack is 90 Hz.) The LFE (low-frequency effect) signals
generated when Dolby Digital or DTS is decoded are also
directed if they are assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on
the subwoofer. It is also possible to adjust the volume level by
using the remote control of this unit (see ADJUSTING THE
LEVEL OF THE EFFECT SPEAKERS on page 66).

• Depending on the settings of “1 SPEAKER SET” and “10 LFE
LEVEL” on the SET MENU, some signals may not be output
from the SUBWOOFER jack.

4 CENTER jack

Center channel line output jack.

5 REAR CENTER jack

Rear center channel line output jack.

18

Connecting the Power Supply Cords

CONNECTIONS

PEDANCE SELECTOR

ET BEFORE POWER ON

MAIN A OR B:

4ΩMIN. /SPEAKER

A+B:

8ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

6ΩMIN. /SPEAKER

:

REAR

6ΩMIN. /SPEAKER

MAIN A OR B:

8ΩMIN. /SPEAKER

A+B:

16ΩMIN. /SPEAKER

:

8ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

8ΩMIN. /SPEAKER

:

REAR

8ΩMIN. /SPEAKER

(U.S.A. model)

VOLTAGE SELECTOR

PEDANCE SELECTOR

ET BEFORE POWER ON

MAIN A OR B:

4ΩMIN. /SPEAKER

A+B:

8ΩMIN. /SPEAKER

:

6ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

6ΩMIN. /SPEAKER

:

REAR

6ΩMIN. /SPEAKER

MAIN A OR B:

8ΩMIN. /SPEAKER

A+B:

16ΩMIN. /SPEAKER

:

8ΩMIN. /SPEAKER

CENTER

:

REAR CENTER

8ΩMIN. /SPEAKER

:

REAR

8ΩMIN. /SPEAKER

AC IN

AC OUTLETS

VOLTAGE SELECTOR

AC OUTLETS

To AC outlet

■ Connecting the AC power cord

[U.S.A. and Canada models]

Plug the power cord into the AC inlet when all
connections are complete, and then plug in this unit to the
wall outlet.

Caution

• Do not use other AC power cords than the one provided.
Otherwise it may result in causing fire or an electrical
shock.

[Australia, China and General models]

Plug in this unit to the wall outlet.

■ AC OUTLET(S) (SWITCHED)

U.S.A., Canada, China and

General models ............................................ 2 OUTLETS

Australia model .............................................. 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). These outlets
will supply power to any connected component whenever
this unit is turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is 80 W.

■ VOLTAGE SELECTOR

(China and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are 110/120/
220/240 V AC, 50/60 Hz.

INTRODUCTION

PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

(China and General models)

APPENDIX

English

19

CONNECTIONS

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

A

B

CD

DVD

VCR2/DVR

VCR 1

TITLE

MENU

CHAPTER

PAUSESTOPPOWER

REC

SELECT

DISPLAY

SEARCH

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

Turning on the Power

When all connections are completed, turn on the power of
this unit.

1

VOLUMEINPUT

6CH INPUT

PRO LOGIC

BASS

TREBLE

– +

– +

STANDBY

/

SPEAKERS

AB

ON

NATURAL SOUND AV RECEIVER

PROCESSOR

BASS

DIRECT

EXTENSION

INPUT M0DE

DIGITAL

SOURCE

/

PRESET

/REMOTE

TUNING

A/B/C/D/E

DVD

MD/TAPE

CD-R

D-TV/LD

CBL/SAT

TUNER

VCR1

CD

STEREO

PROGRAM

VCR2

PHONO

/DVR

V-AUX

EFFECT

REC OUT/ZONE 2

TUNING

PRESET

MODE

MEMORY

/TUNING

FM/AM

EDIT

MAN'L/AUTO FM AUTO/MAN'L MONO

PHONES

S VIDEO

VIDEO AUDIO OPTICALLR

VIDEO AUXSILENT

1

1 Press STANDBY/ON (SYSTEM POWER on

the remote control) to turn on the power of
this unit.

SYSTEM

STANDBY

/ON

Front panel

or

POWER

Remote control

The level of the main volume, and then the current
DSP program name appear on the front panel
display.

2 Turn on the video monitor connected to this

unit.

Same information as above appears on the video
monitor, if the full or short display mode has been
selected.

20

ON-SCREEN DISPLAY (OSD)

You can display the operation information for this unit on
a video monitor. If you display the SET MENU and DSP
program parameter settings on a monitor, it is much easier
to see the available options and parameters than it is by
reading this information on the front panel display.

y

• If a video source is being reproduced, the OSD is
superimposed over the image.

• The OSD signal is not output to the REC OUT jack, and will
not be recorded with any video signal.

• You can set the OSD to turn on (blue background) or off when
a video source is not being reproduced (or the source
component is turned off) by using “13 DISPLAY SET” on the
SET MENU (see page 65).

OSD Modes

You can change the amount of information the OSD
shows.

Full display

This mode always shows the DSP program parameter
settings on the video monitor (see page 71).

Short display

This mode briefly shows the same contents as the front
panel display at the bottom of the screen and then
disappears.

Display off

This mode briefly shows the “DISPLAY OFF” message at
the bottom of the screen and then disappears. Afterwards,
no changes to operations appear on the monitor except
those of the ON SCREEN button.

P01 CONCERT HALL 1

INIT.DLY…………30ms
ROOM SIZE…………1.O
LIVENESS…………………5

Selecting the OSD Mode

1 Turn on the video monitor connected to this

unit.

2 Press ON SCREEN on the remote control

repeatedly to change the display mode.

The OSD mode changes in the following order: full
display, short display, and display off.

ON SCREEN

LEVEL

TESTSLEEP

Notes

• If you choose a video input source that has a component
connected to both the S VIDEO IN and composite VIDEO IN
jacks, and both the S VIDEO OUT and composite VIDEO
OUT jacks are connected to a video monitor, the video signal is
output to both the S VIDEO OUT and VIDEO OUT jacks.
However, the OSD is carried only on the S-video signal. If no
video signal is input, the OSD is carried on both the S-video
and composite video signals.

• If your video monitor is connected only to the COMPONENT
VIDEO jacks of this unit, the OSD is not shown. Make sure to
connect your video monitor to the COMPONENT VIDEO
jacks and either VIDEO or S VIDEO jacks if you want to see
the OSD.

• Playing back video software that has an anti-copy signal or
video signals with a lot of noise may produce unstable images.

PARAMETER

SET MENU

INTRODUCTION

PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

P01 CONCERT HALL 1

Full display Short display

y

• When you choose the full display mode, INPUT l / h,

VOLUME and some other types of operation information are
displayed at the bottom of the screen in the same format as that
for the front panel display.

• The SET MENU and test tone display appear regardless of the
OSD mode.

APPENDIX

English

21

SPEAKER MODE SETTINGS

This unit has 6 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your
configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings
as well as other possible settings.

Summary of SPEAKER SET Items 1A through 1F

Item

1A CENTER SP

1B MAIN SP

1C REAR L/R SP

1D REAR CT SP

1E LFE/BASS OUT

1F MAIN LEVEL

Selects the output mode according to whether or not a center speaker is
being used and its performance.

Selects the output mode according to the performance of the main
speakers.

Selects the output mode according to whether or not rear L/R speakers
are being used and their performance.

Selects the Rear Center channel output according to the size of the Rear
Center speaker.

Selects the speaker according to use for LFE signal output and low bass
signal.

Selects the main speaker level.

Description

Control value (default
setting indicated in bold)

LRG/SML/NONE

LARGE/SMALL

LRG/SML/NONE

LRG/SML/NONE

SWFR/MAIN/BOTH

Normal/–10 dB

If the initial settings shown in the above table are not appropriate for your speaker configuration,
change settings following the steps described in “1 SPEAKER SET” from page 56 to 59.

22

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

CH

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

A/B/C/D/E

ADJUSTING THE SPEAKER OUTPUT LEVELS

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

CH

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

A/B/C/D/E

VOLUME

This section explains how to adjust the speaker output
levels by using the test tone generator. When this
adjustment is made, the output level heard at the listening
position will be the same from each speaker. This is
important for the best performance of the digital sound
field processor, and various decoders (Dolby Digital,
Dolby Pro Logic, Dolby Pro Logic

, DTS, DTS ES, and

DTS Neo: 6).

Note

• Since this unit cannot enter the test mode while headphones are
connected to this unit, be sure to unplug the headphones from
the PHONES jack when using the test tone.

Before You Begin

VOLUMEINPUT

6CH INPUT

PRO LOGIC

BASS

TREBLE

– +

– +

33

STANDBY

SPEAKERS

AB

2

/

ON

NATURAL SOUND AV RECEIVER

PROCESSOR

BASS

DIRECT

EXTENSION

INPUT M0DE

DIGITAL

SOURCE

/

PRESET

/REMOTE

TUNING

A/B/C/D/E

DVD

MD/TAPE

CD-R

D-TV/LD

CBL/SAT

TUNER

VCR1

CD

STEREO

PROGRAM

VCR2

PHONO

/DVR

V-AUX

EFFECT

REC OUT/ZONE 2

TUNING

PRESET

MODE

MEMORY

/TUNING

FM/AM

EDIT

MAN'L/AUTO FM AUTO/MAN'L MONO

PHONES

S VIDEO

VIDEO AUDIO OPTICALLR

VIDEO AUXSILENT

4 Set PARAMETER/SET

MENU on the remote
control to PARAMETER.

PARAMETER

SET MENU

Using the Test Tone (TEST DOLBY SUR.)

Use the test tone to balance the output levels of the 6
speakers required for a surround sound system. The
adjustment of each speaker output level should be made at
your listening position with the remote control.

2

VOLUMEINPUT

6CH INPUT

PRO LOGIC

BASS

TREBLE

– +

– +

STANDBY

/

ON

SPEAKERS

AB

NATURAL SOUND AV RECEIVER

PROCESSOR

BASS

DIRECT

EXTENSION

INPUT M0DE

DIGITAL

SOURCE

/

PRESET

/REMOTE

TUNING

A/B/C/D/E

DVD

MD/TAPE

CD-R

D-TV/LD

CBL/SAT

TUNER

VCR1

CD

STEREO

PROGRAM

VCR2

PHONO

/DVR

V-AUX

EFFECT

REC OUT/ZONE 2

TUNING

PRESET

MODE

MEMORY

/TUNING

FM/AM

EDIT

MAN'L/AUTO FM AUTO/MAN'L MONO

PHONES

S VIDEO

VIDEO AUDIO OPTICALLR

VIDEO AUXSILENT

2

INTRODUCTION

PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

4

1 Turn on the video monitor connected to this

unit.

2 Press SPEAKERS A or B

to select the main
speakers to be used.

If you are using two sets of the
main speakers, press both A
and B.

3 Set the BASS and TREBLE controls on the

front panel to the center position and turn off
BASS EXTENSION and PROCESSOR
DIRECT by pressing the buttons.

“BASS EXT. OFF” and “P. DIRECT OFF” appear
on the front panel display.

BASS

EXTENSION

BASS

–

TREBLE

–

+

+

SPEAKERS

AB

PROCESSOR

DIRECT

Set to OFF.

31, 4

1 Press TEST to output the

test tone.

TEST

2 Adjust the volume so you can hear the test

tone.

The test tone is heard from the left main speaker,
center speaker, right main speaker, right rear speaker,
rear center speaker and left rear speaker in order. The
tone is produced for 2.5 seconds each time.

or

Front panel

VOLUME

Remote control

INFORMATION

ADDITIONAL

APPENDIX

English

23