U
RX-V1400
AV Receiver
OWNER'S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
CAUTION |
RISK OF ELECTRIC SHOCK |
DO NOT OPEN |
CAUTION: TO REDUCE THE RISK OF |
ELECTRIC SHOCK, DO NOT REMOVE |
COVER (OR BACK). NO USER-SERVICEABLE |
PARTS INSIDE. REFER SERVICING TO |
QUALIFIED SERVICE PERSONNEL. |
•Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
1Read Instructions – All the safety and operating instructions should be read before the product is operated.
2Retain Instructions – The safety and operating instructions should be retained for future reference.
3Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.
4Follow Instructions – All operating and use instructions should be followed.
5Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
10Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12Grounding or Polarization – This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
15Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
17Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
18Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a)When the power-supply cord or plug is damaged,
b)If liquid has been spilled, or objects have fallen into the product,
c)If the product has been exposed to rain or water,
l CAUTION
d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,
e)If the product has been dropped or damaged in any way, and
f)When the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
20Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
21Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
22Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer.
23Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
IMPORTANT SAFETY INSTRUCTIONS
24Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST |
ANTENNA |
|
LEAD IN |
|
WIRE |
GROUND |
|
CLAMP |
|
|
ANTENNA |
|
DISCHARGE UNIT |
|
(NEC SECTION 810–20) |
ELECTRIC |
|
SERVICE |
|
EQUIPMENT |
GROUNDING CONDUCTORS |
|
|
|
(NEC SECTION 810–21) |
|
GROUND CLAMPS |
|
POWER SERVICE GROUNDING |
|
ELECTRODE SYSTEM |
|
(NEC ART 250. PART H) |
NEC – NATIONAL ELECTRICAL CODE |
|
FCC INFORMATION (for US customers)
1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
CAUTION II
3
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
2Install this sound system in a well ventilated, cool, dry, clean place — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.
3Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.
4Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.
5Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:
–Other components, as they may cause damage and/or discoloration on the surface of this unit.
–Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.
–Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit.
6Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.
7Do not plug in this unit to a wall outlet until all connections are complete.
8Do not operate this unit upside-down. It may overheat, possibly causing damage.
9Do not use force on switches, knobs and/or cords.
10When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord.
11Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
12Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.
16Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty.
17Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet.
18VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply.
Voltages are 110/120/220/230-240 V AC, 50/60 Hz.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion - and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
Ill4 CAUTION
CONTENTS
INTRODUCTION |
|
FEATURES ............................................................. |
2 |
GETTING STARTED............................................ |
3 |
Supplied accessories .................................................. |
3 |
Installing batteries in the remote control ................... |
3 |
CONTROLS AND FUNCTIONS ......................... |
4 |
Front panel ................................................................. |
4 |
Remote control........................................................... |
6 |
Using the remote control ........................................... |
7 |
Front panel display .................................................... |
8 |
Rear panel ................................................................ |
10 |
PREPARATION |
|
SPEAKER SETUP ............................................... |
11 |
Speaker placement ................................................... |
11 |
Speaker connections ................................................ |
12 |
CONNECTIONS .................................................. |
15 |
Before connecting components................................ |
15 |
Connecting video components................................. |
16 |
Connecting audio components................................. |
19 |
Connecting the antennas .......................................... |
21 |
Connecting the power supply cord .......................... |
22 |
Speaker impedance setting ...................................... |
23 |
Turning on the power............................................... |
23 |
AUTO SETUP....................................................... |
24 |
Introduction.............................................................. |
24 |
Optimizer microphone setup.................................... |
24 |
Starting the setup ..................................................... |
25 |
BASIC SETUP ...................................................... |
28 |
Using BASIC setup.................................................. |
28 |
BASIC OPERATION |
|
PLAYBACK.......................................................... |
30 |
Basic operations....................................................... |
30 |
Selecting sound field programs ............................... |
32 |
Selecting input modes.............................................. |
34 |
TUNING ................................................................ |
36 |
Automatic and manual tuning.................................. |
36 |
Presetting stations .................................................... |
37 |
Selecting preset stations........................................... |
39 |
Exchanging preset stations ...................................... |
39 |
RECORDING ....................................................... |
40 |
SOUND FIELD PROGRAMS |
|
SOUND FIELD PROGRAM |
|
DESCRIPTIONS............................................... |
41 |
For movie/video sources.......................................... |
41 |
For music sources .................................................... |
43 |
ADVANCED OPERATION |
|
ADVANCED OPERATIONS .............................. |
44 |
Selecting the OSD mode.......................................... |
44 |
Using the sleep timer ............................................... |
44 |
Manually adjusting speaker levels........................... |
45 |
Using the test tone ................................................... |
46 |
SET MENU ............................................................ |
47 |
Using SET MENU................................................... |
48 |
Manual setup: SOUND............................................ |
49 |
Manual setup: INPUT.............................................. |
54 |
Manual setup: OPTION........................................... |
56 |
REMOTE CONTROL FEATURES ................... |
59 |
Control area ............................................................. |
59 |
Setting manufacturer codes...................................... |
60 |
Programming codes from other remote controls ..... |
61 |
Changing source names in the display window....... |
62 |
Clearing function sets .............................................. |
63 |
Clearing individual functions .................................. |
63 |
Controlling each component.................................... |
64 |
ZONE 2/ZONE 3 |
|
(U.S.A., Canada and Australia |
|
models only) ....................................................... |
68 |
Zone 2/Zone 3 connections...................................... |
68 |
Remote controlling Zone 2/Zone 3.......................... |
69 |
ADDITIONAL INFORMATION |
|
EDITING SOUND FIELD PARAMETERS ...... |
71 |
What is a sound field ............................................... |
71 |
Changing parameter settings ................................... |
71 |
SOUND FIELD PARAMETER |
|
DESCRIPTIONS............................................... |
73 |
TROUBLESHOOTING ....................................... |
77 |
GLOSSARY........................................................... |
82 |
SPECIFICATIONS............................................... |
85 |
|
INTRODUCTION |
|
|
|
|
|
|
|
|
PREPARATION |
|
|
|
|
|
|
|
|
OPERATION |
BASIC |
|
|
|
|
|
|
|
PROGRAMS |
FIELD SOUND |
|
|
|
|
|
|
|
OPERATION |
ADVANCED |
|
|
|
|
|
|
|
INFORMATION |
ADDITIONAL |
|
|
|
|
|
|
|
English |
|
|
|
|
1
Built-in 7-channel power amplifier
Minimum RMS Output Power (0.04% THD, 20 Hz – 20 kHz, 8Ω) Front: 110 W + 110 W
Center: 110 W
Surround: 110 W + 110 W Surround Back: 110 W + 110 W
Sound field features
Proprietary Yamaha technology for the creation of sound fields
THX
Dolby Digital/Dolby Digital EX Decoder
DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS Neo:6 Decoder, DTS 96/24
Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx Decoder
Virtual CINEMA DSP
SILENT CINEMA™
Sophisticated AM/FM tuner
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset Editing)
Other features
YPAO: YAMAHA Parametric Room Acoustic Optimizer for Automatic Speaker Setup
192-kHz/24-bit D/A Converter
“SET MENU” which Provides You with Items for Optimizing This Unit for Your Audio/Video System
6 or 8-channel External Decoder Input for Other Future Formats
On Screen Display Function Helpful in Controlling This Unit
S Video Signal Input/Output Capability
Component Video Input/Output Capability
Video Signal Conversion (Composite Video ↔
S Video → Component Video) Capability for Monitor Out
Optical and Coaxial Digital Audio Signal Jacks
Sleep Timer
Night Listening Mode
Remote Control with Preset Manufacturer Codes
Zone 2/Zone 3 Custom Installation Facility (U.S.A., Canada and Australia models only)
•yindicates a tip for your operation.
•Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
•This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories.
SILENT CINEMA is a trademark of YAMAHA
CORPORATION.
“DTS” and “DTS-ES Digital Surround” and “Neo:6” are trademarks of Digital Theater Systems, Inc.
THX and the THX logo are registered trademarks of THX Ltd. Surround EX is a jointly developed technology of THX and Dolby Laboratories, Inc. and is a trademark of Dolby Laboratories, Inc. All rights reserved. Used under authorization.
2
Please check that you received all of the following parts.
Remote control |
Batteries (4) |
|||
|
|
|
|
(AAA, R03, UM-4) |
TRANSMIT |
|
RE–NAME CLEAR LEARN |
|
|
SYSTEM |
|
|
|
|
POWER |
STANDBY |
SLEEP |
INPUT MODE |
|
PHONO |
TUNER |
CD |
MULTI CH IN |
|
V-AUX |
CBL/SAT |
MD/TAPE |
CD-R |
|
DTV |
VCR 1 |
DVR/VCR2 |
DVD |
|
|
|
|
SELECT |
|
POWER |
|
POWER |
AMP |
|
TV |
|
AV |
|
|
REC |
|
|
+ |
Speaker terminal wrench |
DISC SKIP |
|
AUDIO |
||
|
|
|
VOL |
|
|
|
|
– |
|
LEVEL |
+ |
SET MENU |
MUTE |
|
TITLE |
MENU |
|
|
|
TV INPUT |
TV VOL |
A/B/C/D/E |
|
|
|
|
|
||
CH |
TV MUTE |
CH |
|
|
– |
SELECT |
+ |
|
|
PRESET |
|
PRESET |
|
|
TEST |
TV VOL |
ON SCREEN |
STRAIGHT |
|
|
|
|
|
|
RETURN |
– |
DISPLAY |
|
|
|
|
|
EFFECT |
|
STEREO |
HALL |
JAZZ |
ROCK |
|
1 |
2 |
3 |
4 |
Optimizer microphone* |
ENTERTAIN |
MUSIC |
TV THTR |
MOVIE |
|
5 |
6 |
7 |
8 |
|
THX |
/DTS |
NIGHT |
EX/ES |
|
9 |
0 |
+10 |
ENTER |
|
|
|
|
CHP/INDEX |
|
Power Cord
(U.S.A., Canada and Europe models)
75-ohm/300-ohm antenna adapter (U.K. model only)
*The optimizer microphone is sensitive to heat.
–Keep it away from direct sunlight.
–Do not place it on top of this unit.
AM loop antenna
Indoor FM antenna (U.S.A., Canada, China, Korea, Asia and General models)
(U.K., Europe and Australia models)
INTRODUCTION
2 1
3
1Press the part and slide the battery compartment cover off.
2Insert four supplied batteries (AAA, R03, UM- 4) according to the polarity markings on the inside of the battery compartment.
3Slide the cover back until it snaps into place.
Notes on batteries
•Change all of the batteries if you notice the condition like; the operation range of the remote control decreases, the indicator does not flash or its light becomes dim.
•Do not use old batteries together with new ones.
•Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.
•If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
If the remote control is without batteries for more than 3 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared.
English
3
1 |
2 |
3 |
4 5 6 7 8 |
9 |
(U.S.A. model)
|
|
|
|
|
|
|
|
|
|
VOLUME |
|
|
INPUT |
|
|
|
|
|
|
|
|
|
STANDBY |
|
|
|
|
|
|
|
|
|
|
/ON |
|
|
|
|
|
|
|
|
|
|
|
|
A/B/C/D/E |
PRESET/ |
PRESET |
FM/AM |
MEMORY |
TUNING |
|
PROGRAM |
|
|
|
TUNING |
/TUNING |
MODE |
|
|
|||
|
|
|
TUNER |
|
|
|
|
|
|
|
|
SPEAKERS |
MULTI CH |
INPUT MODE |
|
EDIT |
|
MAN'L/AUTO FM |
|
TONE CONTROL |
STRAIGHT |
A |
B |
INPUT |
|
|
PHONES |
S VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
DSP |
|
|
|
|
|
|
EFFECT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OPTIMIZER |
|
|
|
|
|
|
|
|
|
|
MIC |
|
SILENT |
|
|
|
|
|
RDS MODE |
|
|
|
|
/FREQ EON |
PTY SEEK |
|
|
0 A B |
C D E F G |
MODE START |
H I |
J |
K L M N
(U.K. and Europe models only)
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When you turn on this unit, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound.
Note
In standby mode, this unit consumes a small amount of power in order to receive infrared-signals from the remote control.
2 INPUT selector
Selects the input source you want to listen to or watch.
3 Remote control sensor
Receives signals from the remote control.
4 Front panel display
Shows information about the operational status of this unit.
5 PRESET/TUNING EDIT
Switches the function of PRESET/TUNING l / h between selecting preset station numbers and tuning.
6 FM/AM
Switches the reception band between FM and AM.
7 MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for more than 3 seconds to start automatic preset tuning.
8TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic (“AUTO” indicator on) and manual (“AUTO” indicator off).
9VOLUME
Controls the output level of all audio channels. This does not affect the REC OUT level.
0 SPEAKERS A/B
Turn on or off the set of front speakers connected to the A and/or B terminals on the rear panel at each time the corresponding button is pressed.
A MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT jacks. When selected, the MULTI CH INPUT source takes priority over the source selected with INPUT (or the input selector buttons on the remote control).
4
B INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of signals received when one component is connected to two or more of this unit’s input jacks (see page 34). Priority cannot be set when MULTI CH INPUT is selected as the input source.
C OPTIMIZER MIC jack
Use to connect and input audio signals from the supplied microphone for use with the AUTO SETUP function (see page 24).
D A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
E PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:) is displayed next to the band indication in the front panel display.
Selects the tuning frequency when the colon (:) is not displayed.
F SILENT (PHONES jack)
Outputs audio signals for private listening with headphones. When you connect headphones, no signals are output to the OUTPUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down to the left and right headphone channels.
G VIDEO AUX jacks
Input audio and video signals from a portable external source such as a game console. To reproduce source signals from these jacks, select V-AUX as the input source.
H TONE CONTROL
Use to adjust the bass/treble balance for the front left/right and center channels (see page 31).
I PROGRAM
Use to select sound field programs or adjust bass/treble balance (in conjunction with TONE CONTROL).
J STRAIGHT/EFFECT
Switches the sound fields off or on. When STRAIGHT is selected, input signals (2-channel or multi-channel) are output directly from their respective speakers without effect processing.
CONTROLS AND FUNCTIONS
■ U.K. and Europe models only
K RDS MODE/FREQ
Press this button when the unit is receiving an RDS station to cycle the display mode between the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data service) and/or the frequency display mode.
L EON
Press this button to select a radio program type (NEWS, INFO, AFFAIRS, SPORT) to tune in automatically.
M PTY SEEK MODE
Press this button to set the unit to the PTY SEEK mode.
N PTY SEEK START
Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode.
■ Opening and closing the front panel door
When you want to use the controls behind the front panel door, open the door by gently pressing on the lower part of the panel. Keep the door closed when not using these controls.
INTRODUCTION
To open, press gently on the lower part of the panel.
English
5
CONTROLS AND FUNCTIONS
This section describes the function of each control on the remote control. See “REMOTE CONTROL FEATURES” on page 59 to operate other components with this remote control.
1 |
|
|
|
|
B |
2 |
TRANSMIT |
|
RE–NAME CLEAR |
LEARN |
C |
|
|
D |
|||
3 |
|
|
|
|
|
SYSTEM |
STANDBY |
|
INPUT MODE |
E |
|
|
POWER |
SLEEP |
|||
4 |
|
|
|
|
|
|
PHONO |
TUNER |
CD |
MULTI CH IN |
F |
|
|
|
|
|
G |
|
V-AUX |
CBL/SAT |
MD/TAPE |
CD-R |
|
5 |
DTV |
VCR 1 |
DVR/VCR2 |
DVD |
|
6 |
|
|
|
SELECT |
H |
|
POWER |
|
POWER |
AMP |
I |
|
TV |
|
AV |
|
J |
7 |
REC |
|
|
|
K |
|
|
AUDIO |
+ |
||
|
DISC SKIP |
|
|
|
VOL
8
9
0
A
LEVEL |
+ |
|
TITLE |
||
TV INPUT |
TV VOL |
|
|
||
CH |
TV MUTE |
|
– |
||
SELECT |
||
PRESET |
|
|
TEST |
TV VOL |
|
|
||
RETURN |
– |
|
STEREO |
HALL |
1 2
ENTERTAIN MUSIC
5 6
THX /DTS
9 0
–
SET MENU |
MUTE |
MENU |
L |
A/B/C/D/E |
|
|
M |
CH |
|
+ |
N |
PRESET |
ON SCREEN |
STRAIGHT |
O |
DISPLAY |
|
|
|
|
|
|
EFFECT |
|
JAZZ |
ROCK |
|
3 |
4 |
|
TV THTR |
MOVIE |
|
7 |
8 |
|
NIGHT |
EX/ES |
P |
+10 |
ENTER |
|
|
CHP/INDEX |
|
1 Infrared window
Outputs infrared control signals. Aim this window at the component you want to operate.
2 TRANSMIT indicator
Flashes while the remote control is sending signals.
3 STANDBY
Sets this unit in the standby mode.
4 SYSTEM POWER
Turns on the power of this unit.
5 Input selector buttons
Select the input source and change the control area.
6 Display window
Shows the name of the selected source component that you can control.
7 Operation buttons
Provide functions such as play, stop, skip, etc. for use when operating other components.
8 LEVEL (TITLE)
Selects the speaker channel to be adjusted and sets the level.
9 Cursor buttons u / d / j / i
Use to select and adjust DSP program parameters or SET MENU items.
0 TEST (RETURN)
Outputs the test tone to adjust the speaker levels.
ASound field program/Numeric buttons
Use to select sound field programs or input numbers.
BRE-NAME
Used for changing the input source name in the display window (see page 62).
C CLEAR
Used for clearing functions acquired when using the learn and rename features, or setting manufacturer codes (see page 63).
D LEARN
Used for setting up the manufacturer code or for programming functions from other remote controls (see pages 60 and 61).
E SLEEP
Sets the sleep timer.
F INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of signals received when one component is connected to two or more of this unit’s input jacks (see page 34). Priority cannot be set when MULTI CH INPUT is selected as the input source.
G MULTI CH IN
Selects the MULTI CH INPUT mode when using an external decoder (etc.).
6
H SELECT k/n
Selects another component that you can control independently of the input component selected with the input selector buttons.
I AV POWER
Turns on and off the power of the component selected by the input selector button.
J AMP
Selects AMP or other component selected by the input selector button.
K VOL –/+
Increases or decreases the volume level.
L MUTE
Mutes the sound. The MUTE indicator turns on when the MUTE function is on. Press again to restore the audio output to the previous volume level.
MSET MENU (MENU)
Selects the SET MENU mode.
NON SCREEN (DISPLAY)
Selects the on-screen display (OSD) mode for your video monitor.
O STRAIGHT/EFFECT
Switches the sound fields off or on. When STRAIGHT is selected, input signals (2-channel or multi-channel) are output directly from their respective speakers without effect processing.
P EX/ES
Switches between 5.1 or 6.1/7.1 channel playback of multi-channel software.
CONTROLS AND FUNCTIONS
INTRODUCTION
30 |
30 |
Approximately 6 m (20 feet) |
The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.
■ Handling the remote control
•Do not spill water or other liquids on the remote control.
•Do not drop the remote control.
•Do not leave or store the remote control in the following types of conditions:
–high humidity such as near a bath
–high temperature such as near a heater or stove
–extremely low temperature
–dusty places
English
7
CONTROLS AND FUNCTIONS
1 |
|
|
2 |
3 |
|
4 |
5 |
|
6 |
7 |
8 |
9 |
|
|
V–AUX |
DVR/VCR2 |
VCR 1 |
CBL/SAT |
DTV |
DVD |
MD/TAPE |
CD–R |
CD |
TUNER |
|
PHONO |
|
|
96 |
MATRIX |
|
|
ZONE2 |
|
|
OPTIMIZER |
PS PTY RT CT STEREO AUTO MUTE VOLUME |
||||
|
|
VIRTUAL |
ZONE3 SLEEP |
|
|
HiFi DSP EON PTY HOLD TUNED MEMORY |
|
|
|||||
|
24 |
DISCRETE |
NIGHT |
|
|
|
|
||||||
DIGITAL |
EX |
|
|
|
|
|
|
|
|
96/24 |
|
||
PL |
PL |
|
SILENT |
|
|
|
|
|
|
|
ft |
L C R |
|
|
|
|
|
|
|
|
|
|
|
||||
THX |
PCM |
|
SP |
|
|
|
|
|
|
|
mS |
LFE |
SL SB SR |
|
A B |
|
|
|
|
|
|
|
dB |
|
|
||
0 A BC DE F G |
|
H I |
|
J K LM N O |
P (U.S.A., Canada and |
Q (U.K. and Europe models only) |
Australia models only) |
|
1 Decoder indicators
When any of this unit’s decoders function, the respective indicator lights up.
2 Sound field indicators
Light to indicate the active DSP sound fields.
Presence DSP sound field
|
Listening position |
Left surround |
Right surround |
DSP sound field |
DSP sound field |
Surround back DSP sound field
3 Input source indicators
A cursor lights to show the current input source.
4 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field program.
5 OPTIMIZER indicator
Lights up during the auto setup procedure and when the auto setup speaker settings are used without any modifications.
6 STEREO indicator
Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the “AUTO” indicator is lit.
7 AUTO indicator
Shows that this unit is in the automatic tuning mode.
8 MUTE indicator
Lights up while the MUTE function is on.
9 VOLUME level indicators
Indicate the volume level.
0 THX indicator
Lights up when a THX program is selected.
A PCM indicator
Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals.
B Headphones indicator
Lights up when headphones are connected.
C SP A B indicators
Light up according to the set of front speakers selected. Both indicators light up when both sets of speakers are selected, or when bi-wiring.
D SILENT CINEMA indicator
Lights up when headphones are connected and a sound field program is selected (see page 31).
E NIGHT indicator
Lights up when you select night listening mode.
F VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see page 34).
G SLEEP indicator
Lights up while the sleep timer is on.
H Multi-information display
Shows the current sound field program name and other information when adjusting or changing settings.
I HiFi DSP
Lights when you select a HiFi DSP sound field program.
8
J TUNED indicator
Lights up when this unit is tuned in to a station.
K MEMORY indicator
Flashes to show a station can be stored.
L 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
M LFE indicator
Lights up when the input signal contains the LFE signal.
N Input channel indicators
Indicate the channel components of current digital input signal.
OPresence and surround back speaker indicators
Indicate the connection of presence and/or surround back speakers when using the SPEAKERS setting (page 29) or SP LEVEL setting (page 50).
PZONE 2/ZONE 3 indicators
(U.S.A., Canada and Australia models only)
Light up while Zone 2 or Zone 3 signal is output.
Q RDS indicators
(U.K. and Europe models only)
The name(s) of the RDS data offered by the currently received RDS station light(s) up.
EON lights up when an RDS station that offers the EON data service is being received.
PTY HOLD lights up while searching for stations in the PTY SEEK mode.
CONTROLS AND FUNCTIONS
INTRODUCTION
English
9
CONTROLS AND FUNCTIONS
1 |
2 |
|
|
3 |
|
|
|
|
4 |
|
5 |
|
6 |
7 |
|
DIGITAL OUTPUT |
AUDIO |
AUDIO |
|
VIDEO |
COMPONENT VIDEO |
|
|
|
|
REMOTE |
CONTROL OUT |
|
|
||
OPTICAL |
R L |
R |
L |
VIDEO S VIDEO |
PR PB |
Y |
|
|
|
|
|
|
|
|
|
MD/TAPE |
|
|
|
|
DVD |
|
|
|
IN |
OUT |
|
|
|
|
|
|
IN |
|
|
|
|
|
|
|
|
|
|
||||
|
|
DVD |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(PLAY) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CD-R |
MD/TAPE |
|
|
|
|
|
|
|
|
|
|
+12V 15mA MAX. |
|
|
|
|
|
|
|
|
|
+ |
– |
A |
– |
+ |
|
|
|
||
|
OUT |
|
DTV |
|
DTV |
|
R |
L |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|||||
|
(REC) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIGITAL INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CD |
IN |
|
CBL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
(PLAY) |
|
/SAT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FRONT |
+ |
– |
|
– |
+ |
– |
CENTER |
|
DVD |
CD-R |
|
|
|
MONITOR OUT |
|
|
B |
+ |
|
|||||
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
IN |
|
TUNER |
|
|
|
|
|
|
|
|
|
|
|
|
(REC) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTV |
|
|
VCR 1 |
|
AM |
|
|
|
|
|
|
|
|
AC OUTLETS |
|
|
CD |
|
OUT |
|
ANT |
R |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
CBL/SAT |
PHONO |
|
|
|
GND |
FRONT |
|
|
|
SURROUND |
|
|
|
|
|
|
|
|
|
|
+ |
– |
|
– |
+ |
|
|
|
|||
|
|
|
IN |
|
|
R |
|
L |
|
|
|||||
|
|
|
|
FM ANT |
R |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
R |
L |
|
|||
|
|
|
DVR/ |
|
75Ω |
|
|
|
|
|
|
|
|
||
COAXIAL |
FRONT (6CH)/SB (8CH) |
|
VCR 2 |
|
UNBAL. |
SURROUND |
|
|
|
|
|
|
|
|
|
CD |
|
|
OUT |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
+ |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SURROUND |
ZONE 2 |
CD-R |
|
|
SUB |
R + |
– |
|
– |
+ |
L |
|
|
|
DVD |
|
|
|
|
|
WOOFER |
CENTER |
|
|
|
|
|
|
|
|
|
|
|
|
|
R |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
– |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DVR/ |
|
|
|
|
|
|
SURROUND BACK |
|
|
|
|
|
|
|
|
VCR 2 |
|
|
|
|
|
|
|
SURROUND BACK |
SINGLE |
|
|
|
|||
|
|
|
|
|
|
|
/PRESENCE |
|
PRESENCE/ ZONE 2 |
|
|||||
|
|
|
|
|
|
|
PRE OUT |
|
|
SPEAKERS |
|
|
|
|
|
|
SUB |
ZONE 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WOOFER CENTER |
|
MONITOR OUT |
|
|
|
|
|
|
|
|
|
|
|
|
GND |
MULTI CH INPUT |
OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(U.S.A. model) |
|
8 |
9 |
: |
|
|
A |
|
B |
|
C |
|
|
D |
|
||
1 DIGITAL OUTPUT jacks |
|
|
|
0 ZONE 2 / ZONE 3 OUTPUT jacks |
|
||||||||||
See page 19 for details. |
|
|
|
|
|
(U.S.A., Canada and Australia models only) |
See page 68 for details.
2 Audio component jacks
See page 19 for connection information.
3 Video component jacks
A Antenna terminals
See page 21 for connection information.
See pages 16 and 18 for connection information.
4REMOTE IN/OUT jacks
(U.S.A., Canada and Australia models only)
See page 69 for details.
5CONTROL OUT jack
(U.S.A., Canada and Australia models only)
This is control expansion terminal for commercial use.
6 AC OUTLET(S)
Use to supply power to your other A/V components (see page 22).
7AC INLET (U.S.A. and Canada models only)
Use this inlet to plug in the supplied power cable (see page 22).
8DIGITAL INPUT jacks
See pages 16, 18 and 19 for details.
9 MULTI CH INPUT jacks
See page 17 for connection information.
B PRE OUT jacks
See page 20 for connection information.
C Speaker terminals
See page 12 for connection information.
DPRESENCE/ZONE 2 speaker terminals (U.S.A., Canada and Australia models)
PRESENCE speaker terminals (other models)
See page 12 for connection information.
< Asia and General models only >
FREQUENCY STEP switch
See page 21.
VOLTAGE SELECTOR
See page 22.
10
+
PL |
|
PR |
FL |
C |
FR |
30˚
SL |
|
SR |
|
|
60˚ |
SL |
80˚ |
SR |
|
SBL |
SBR |
more than 30 cm (12 inches)
y
The speaker layout above shows the standard ITU-R speaker setting. You can use it to enjoy CINEMA DSP, multi-channel audio sources and THX.
1.8 m (6 feet) |
1.8 m (6 feet) |
Front speakers (FR and FL)
The front speakers are used for the main source sound plus effect sounds. Place these speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Align the front face of the center speaker with the front face of your video monitor. Place the speaker centrally between the front speakers and as close to the monitor as possible, such as directly over or under it.
Surround speakers (SR and SL)
The surround speakers are used for effect and surround sounds. Place these speakers behind your listening position, facing slightly inwards, about 1.8 m (6 feet) above the floor.
Surround back speakers (SBR and SBL)
The surround back speakers supplement the surround speakers and provide for more realistic front-to-back transitions. Place these speakers directly behind the listening position and at the same height as the surround speakers. They should be positioned at least 30 cm (12 inches) apart. Ideally, they should be positioned at the same width as the front speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity reproduction of the LFE (lowfrequency effect) channel included in Dolby Digital and DTS software. The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.
Presence speakers (PR and PL)
Presence speakers supplement the sound from the front speakers with extra ambient effects produced by CINEMA DSP (see page 41). These effects include sounds that filmmakers intend to locate a little farther back behind the screen in order to create more theater-like ambience. Place these speakers at the front of the room about 0.5 - 1 m (1-3 feet) outside the front speakers, facing slightly inwards, and about 1.8 m (6 feet) above the floor.
■ Di-pole speaker layout
Either di-pole or direct radiating speaker types can be used for THX surround. If you choose di-pole speakers, please place the surround and surround back speakers according to the speaker layout below.
FL |
C |
FR |
SL |
SR |
30˚ |
30˚ |
SBL |
SBR |
:Di-pole speaker
:Direction of di-pole speaker
English
11
SPEAKER SETUP
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.
CAUTION
•If you will use 6 ohm speakers, be sure to set this unit’s speaker impedance setting to 6 ohms before using (see page 23).
•Before connecting the speakers, make sure that the power of this unit is off.
•Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or speakers.
•Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red) terminals on this unit and your speaker. Connect the plain cable to the “–” (black) terminals.
10 mm (3/8")
1 2
1Remove approximately 10 mm (3/8") of insulation from each of the speaker cables.
2Twist the exposed wires of the cable together to prevent short circuits.
3Unscrew the knob.
y
Supplied speaker terminal wrench is useful to screw or unscrew knobs.
4Insert one bare wire into the hole in the side of each terminal.
5 Tighten the knob to secure the wire.
5 |
4 |
3 |
Red: positive (+)
Black: negative (–)
Connecting to PRESENCE/ZONE 2 or PRESENCE speaker terminals
1 |
Open the tab. |
|
2 |
1 |
3 |
Insert one bare wire into |
|
|
|
the hole of each terminal. |
2 |
3 |
|
|
Return the tab to secure |
|
|
|
the wire. |
|
Banana plug connections
(With the exception of U.K., Europe and Asia models) First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.
Banana plug
(With the exception of U.K., Europe and Asia models)
12
SPEAKER SETUP
|
9 |
|
|
10 |
2 |
|
|
|
|
|
|
|
4 |
1 |
7 |
3 |
|
||
|
|
||
|
|
|
|
|
8 |
|
5 |
|
|
|
6 |
Subwoofer
system
Speaker layout
1
Front speakers (A) |
|
|
|
|
|
|
|
|
||||||||||
|
Right |
|
|
Left |
Center |
Front |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
speaker |
speakers |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(B) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
3 |
|
|
|
|
|
|
|
4 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
R + |
– |
A |
– |
+ |
L |
|
|
|
FRONT |
– |
|
|
|
|
CENTER |
|
|
|
+ |
B |
– |
+ |
– |
+ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC OUTLETS |
|
|
+ |
– |
SURROUND |
– |
+ |
|
|
|
R |
|
L |
|
||||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
R |
L |
|
|
|
|
|
|
|
+ |
|
SUB |
R |
+ |
– |
|
– |
+ |
L |
|
WOOFER |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
– |
|
|
|
|
SURROUND BACK |
SINGLE |
PRESENCE/ ZONE 2 |
|||
|
PRE OUT |
|
|
|||||
|
|
|
SPEAKERS |
|
|
|
|
(U.S.A. model)
7 |
|
|
|
8 |
5 |
|
|
|
6 |
9 |
|
|
|
10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Right |
|
Left |
|
Right |
Left |
|
Right |
Left |
|||||
Surround speakers |
Surround back speakers |
Presence speakers |
PREPARATION
You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously.
•The surround back speakers output the surround back channel included in Dolby Digital EX and DTS ES software and only operate when the Dolby Digital EX or DTS ES decoder is turned on.
•The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields are selected.
English
13
SPEAKER SETUP
■ FRONT terminals
Connect one or two speaker systems to these terminals. If you use only one speaker system, connect it to either the FRONT A or B terminals.
Note
The Canada model cannot output to two separate speaker systems simultaneously.
Bi-wired connection
The unit also allows you to make bi-wired connections to one speaker system. Use two pairs of speaker cables for each speaker (one pair for the woofer and one pair for the tweeter/ mid-range). To use the bi-wired connections, press SPEAKERS A and SPEAKERS B on the front panel so that both SP A and B light up on the front panel display.
Bi-wired connection
R + |
– |
A |
– |
+ |
L |
FRONT + |
– |
B |
– |
+ |
|
|
|
|
|
|
■ CENTER terminals
Connect a center speaker to these terminals.
■ SURROUND terminals
Connect surround speakers to these terminals.
■ SUBWOOFER jack
Connect a subwoofer with built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.
■ SURROUND BACK terminals
Connect surround back speakers to these terminals. If you only connect one surround back speaker, connect it to the left (L) terminals.
■ PRESENCE terminals
Connect presence speakers to these terminals.
*If you are using either U.S.A., Canada or Australia model, you can also use these speakers as Zone 2 speakers (see page 58).
This unit
14
CAUTION
Do not connect this unit or other components to the mains power until all connections between components are complete.
■ Signal directions and cable indications
audio signal direction |
|
video signal direction |
|
For analog signals |
|
left analog cables |
L |
right analog cables |
R |
For digital signals |
|
optical cables |
O |
coaxial cables |
C |
For video signals |
|
video cables |
V |
S-video cables |
S |
|
V |
■ Analog jacks
You can input analog signals from audio components by connecting audio pin cable to the analog jacks on this unit. Connect red plugs to the right jacks and white plugs to the left jacks.
■ Digital jacks
This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. All digital input jacks are compatible with 96-kHz sampling digital signals.
Note
This unit handles digital and analog signals independently. Thus audio signals input to the analog jacks are only output to the analog OUT (REC) jacks. Likewise audio signals input to the digital (OPTICAL or COAXIAL) jacks are only output to the DIGITAL OUTPUT jacks.
Dust protection cap
Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust.
■ Video jacks
This unit has three types of video jacks. Connection depends on the availability of input jacks on your monitor. The signals input through the VIDEO jack on this unit can be output through the S VIDEO and COMPONENT VIDEO jacks (see page 56). The signals input through the S VIDEO jack can be output through the VIDEO jack when V CONV. is set to ON (see page 56).
COMPONENT VIDEO
VIDEO |
S VIDEO |
PR |
PB |
Y |
|
VIDEO jack
For conventional composite video signals.
S VIDEO jack
For S-video signals, separated into luminance (Y) and color (C) video signals to achieve high-quality color reproduction.
COMPONENT VIDEO jacks
For component signals, separated into luminance (Y) and color difference (PB, PR) to provide the best quality in picture reproduction.
Note
When signals are input through both the S VIDEO and VIDEO jacks, signals input through the S VIDEO jack have priority.
PREPARATION
English
15
CONNECTIONS
■ Connections for DVD playback
Optical out |
Video out |
|
DVD player |
Audio out |
|
O |
R L |
DIGITAL OUTPUT |
AUDIO |
|
AUDIO |
VIDEO |
|
COMPONENT VIDEO |
|
|
||
OPTICAL |
R |
L |
R |
L |
VIDEO |
S VIDEO |
PR |
PB |
Y |
|
MD/TAPE |
|
|
|
|
|
|
DVD |
|
|
|
|
IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
DVD |
|
|
|
|
|
|
|
(PLAY) |
|
|
|
|
|
|
|
|
|
CD-R |
MD/TAPE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTV |
|
|
|
|
|
OUT |
|
|
|
DTV |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
(REC) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIGITAL INPUT |
|
|
|
|
|
|
|
|
Video in |
Video |
CD |
IN |
|
|
|
CBL |
|
|
|
||
|
|
|
|
|
|
|
|
monitor |
||
|
(PLAY) |
|
|
|
/SAT |
|
|
|
|
|
DVD |
CD-R |
|
|
|
|
|
MONITOR OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OUT |
|
|
|
IN |
|
|
TUNER |
|
|
|
(REC) |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VCR 1 |
|
|
AM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CD |
|
|
|
OUT |
|
|
ANT |
|
|
|
|
|
|
|
|
|
|
|
||
|
PHONO |
|
|
|
|
|
|
GND |
M |
|
CBL/SAT |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
IN |
|
|
|
|
|
|
MAIN/SURROUND BACK |
|
|
DVR/ |
|
|
FM ANT |
|
|
|
COAXIAL |
|
|
VCR 2 |
|
|
|
|
|||
|
|
|
|
|
|
|
SUR |
|
||
CD |
|
|
|
|
OUT |
|
|
|
|
|
|
|
|
|
|
|
75Ω |
|
|
||
|
|
|
|
|
|
|
|
UNBAL. |
|
|
|
SURROUND |
|
|
ZONE 2 |
CD-R |
|
|
|
SU |
|
DVD |
|
|
|
|
|
|
|
|
WO |
|
|
|
|
|
|
|
|
|
|
|
|
DTV |
|
|
|
|
|
|
|
|
|
|
|
SUB |
CENTER |
|
ZONE 3 |
|
|
|
|
|
|
|
WOOFER |
|
MONITOR OUT |
|
|
|
|
|||
GND |
MULCH CH INPUT |
OUTPUT |
|
|
|
|
|
|
(U.S.A. model)
16
CONNECTIONS
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from a multi-disc player, external decoder, sound processor or preamplifier.
If you set EXT.INPUT 6ch/8ch to “8ch” (see page 55), you can use input jacks assigned in EXT.INPUT FRONT (page 55) together with the MULTI CH INPUT jacks to input 8 channels.
Connect the output jacks on your multi-disc player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the front and surround channels.
|
For 6-channel input |
|
|
For 8-channel input |
|
|
|
|
|
FRONT(6CH)/SB(8CH) |
|
|
FRONT(6CH)/SB(8CH) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AUDIO |
|
AUDIO |
|
|
|
|
|
R |
L |
R |
L |
|
SURROUND |
|
|
SURROUND |
IN |
|
|
DVD |
|
|
|
|
(PLAY) |
|
|
||
|
|
|
|
|
MD/TAPE |
|
|
|
|
|
|
|
|
|
|
|
DTV |
|
SUB |
|
|
SUB |
IN |
|
|
CBL |
|
WOOFER CENTER |
|
|
WOOFER CENTER |
(PLAY) |
|
|
/SAT |
|
MULTI CH INPUT |
|
|
MULTI CH INPUT |
CD-R |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN |
|
|
|
R L |
|
R L |
|
|
VCR 1 |
R L |
Subwoofer |
R L |
Subwoofer |
|
|
|
||
|
CD |
|
|
|
||||
|
|
|
|
|
|
|||
|
out |
|
|
out |
|
|
|
|
|
Center |
|
|
Center |
Surround |
|
|
IN |
|
out |
|
|
out |
|
|
DVR/ |
|
|
|
|
|
|
out |
|
|
VCR 2 |
|
Multi-disc player/ |
|
|
Multi-disc player/ |
|
|
|
|
Front External decoder |
Surround |
Surround |
External decoder |
R |
|
|
|
|
|
L |
|
|
|
||||
out |
|
out |
back out |
|
|
|
|
|
|
|
Front out |
|
|
|
|||
|
|
|
|
|
|
|
|
.
Notes
•When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot select sound field programs.
•This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that you connect at least a 5.1-channel speaker system before using this feature.
•When headphones are used, only front L/R channels are output.
PREPARATION
English
17
CONNECTIONS
■ Connections for other video components
Optical out |
Cable TV or |
Video out |
|
|
|
|
satellite tuner |
|
Audio out |
|
|
O |
R L |
|
DIGITAL OUTPUT |
AUDIO |
|
AUDIO |
VIDEO |
|
COMPONENT VIDEO |
|
||
OPTICAL |
R |
L |
R |
L |
VIDEO |
S VIDEO |
PR |
PB |
Y |
MD/TAPE |
|
|
|
|
|
|
DVD |
|
|
|
IN |
|
|
|
|
|
|
|
|
|
|
|
|
DVD |
|
|
|
|
|
|
(PLAY) |
|
|
|
|
|
|
|
|
CD-R |
MD/TAPE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTV |
|
|
|
|
OUT |
|
|
|
DTV |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
(REC) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIGITAL INPUT |
|
|
|
|
|
|
|
|
|
CD |
IN |
|
|
|
CBL |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
(PLAY) |
|
|
|
/SAT |
|
|
|
|
CD-R |
CD-R |
|
|
|
|
|
MONITOR OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
OUT |
|
|
|
IN |
|
|
TUNER |
|
|
(REC) |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
DVD |
|
|
|
|
VCR 1 |
|
|
AM |
|
|
|
|
|
|
|
|
|
||
|
CD |
|
|
|
OUT |
|
|
ANT |
|
|
|
|
|
|
|
|
|
||
|
PHONO |
|
|
|
|
|
|
GND |
MA |
CBL/SAT |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
||
|
|
|
|
|
IN |
|
|
|
|
|
MAIN/SURROUND BACK |
|
|
DVR/ |
|
|
FM ANT |
|
|
COAXIAL |
|
|
VCR 2 |
|
|
|
|||
|
|
|
|
|
|
|
SURR |
||
CD |
|
|
|
|
OUT |
|
|
|
|
|
|
|
|
|
|
75Ω |
|
||
|
|
|
|
|
|
|
|
UNBAL. |
|
|
SURROUND |
|
|
ZONE 2 |
CD-R |
|
|
|
SUB |
DVD |
|
|
|
|
|
|
|
|
WOOF |
|
|
|
|
|
|
|
|
|
|
DVR/ |
|
|
|
|
|
|
|
|
|
VCR2 |
|
|
|
|
|
|
|
|
|
|
SUB |
CENTER |
|
ZONE 3 |
|
|
|
|
|
|
WOOFER |
|
MONITOR OUT |
|
|
|
|||
GND |
MULCH CH INPUT |
OUTPUT |
|
|
|
|
|
(U.S.A. model)
C |
R L |
R L |
Connect a YAMAHA CD recorder that outputs OSD signals.
Audio in DVD recorder Video in or VCR
Audio out Video out
Coaxial out
■ VIDEO AUX jacks (on the front panel)
Use these jacks to connect any video |
S VIDEO |
VIDEO |
L |
AUDIO R |
OPTICAL |
source, such as a game console or |
|
|
VIDEO AUX |
|
|
camcorder, to this unit. |
S |
V |
L |
R |
O |
Optical out
Audio out R
Audio out L
Video out
S video out
Game console or video camera
18
CONNECTIONS
■ Connections for audio components
|
Optical in |
|
|
|
|
MD recorder or |
|||
|
|
tape deck |
|
|
|
Audio out |
|
|
Audio in |
O |
R |
L |
R |
L |
|
|
DIGITAL OUTPUT |
AUDIO |
|
AUDIO |
||
|
OPTICAL |
MD/TAPE |
R |
L |
R |
L |
|
|
|
|
|
|
|
|
|
|
IN |
|
|
|
|
|
|
(PLAY) |
|
|
|
|
|
CD-R |
MD/TAPE |
|
|
|
|
|
|
|
|
|
|
|
|
|
OUT |
|
|
|
|
|
|
(REC) |
|
|
|
Optical out |
DIGITAL INPUT |
|
|
|
|
|
|
CD |
IN |
|
|
|
|
|
O |
|
|
|
|
|
|
|
(PLAY) |
|
|
|
|
|
|
|
CD-R |
|
|
|
|
|
|
OUT |
|
|
|
|
|
|
(REC) |
|
|
|
|
Audio out |
DVD |
|
|
|
|
|
L |
|
CD |
|
|
|
CD player |
|
|
|
|
|
|
R |
CBL/SAT |
PHONO |
|
|
|
|
|
|
|
|
|
|
|
|
|
COAXIAL |
MAIN/SURROUND BACK |
|
|
|
|
|
|
|
|
|
|
|
C |
CD |
|
|
|
|
Coaxial out |
|
|
SURROUND |
|
|
ZONE 2 |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
DVD |
|
|
|
|
|
|
DTV |
|
|
|
|
|
|
|
SUB |
CENTER |
|
ZONE 3 |
|
|
|
WOOFER |
|
||
|
GND |
MULCH CH INPUT |
OUTPUT |
(U.S.A. model)
Optical in
O
Audio out
L
R
CD recorder*
L
R
Audio in
*Some CD recorders can be connected to the VIDEO CD-R jacks (see page 18).
Audio out
L
R
GND
Turntable
■ Connecting a turntable |
y |
|
PHONO jacks are for connecting a turntable with an MM |
Connect your turntable to the GND terminal to reduce noise in |
|
or high-output MC cartridge. If you have a turntable with |
the signal. However you may hear less noise without the |
|
connection to the GND terminal for some record players. |
||
a low-output MC cartridge, use an in-line boosting |
||
|
||
transformer or MC-head amplifier when connecting to |
|
|
these jacks. |
|
PREPARATION
English
19
CONNECTIONS
■ Connecting to an external amplifier
If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the PRE OUT jacks as follows.
Notes
•When audio pin plugs are connected to the PRE OUT jacks for output to an external amplifier, it is not necessary to use the corresponding SPEAKERS terminals. Set the volume of the amplifier connected to this unit to the maximum.
•The signal output through the FRONT PRE OUT and CENTER PRE OUT jacks are affected by the TONE CONTROL settings.
•Signals will only be output from the FRONT PRE OUT jacks when SPEAKER A is turned off with ZONE B selected for SP B SET (see page 57).
|
R |
L |
|
FRONT |
|
|
R |
L |
|
SURROUND |
|
5 |
SUB |
CENTER |
|
WOOFER |
|
|
R |
L |
|
|
SURROUND BACK |
|
|
/PRESENCE |
PRE OUT
1
2
3
4
1FRONT PRE OUT jacks
Front channel line output jacks.
2SURROUND PRE OUT jacks
Surround channel line output jacks.
3CENTER PRE OUT jack
Center channel line output jack.
4SURROUND BACK / PRESENCE PRE OUT
jacks
Surround back or presence channel line output jacks.
5 SUBWOOFER PRE OUT jack
Connect a subwoofer with built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.
Notes
•Each PRE OUT jack outputs the same channel signal as the corresponding speaker terminals. However, when both surround back and presence speakers are connected to this unit, the channel of the signals output from SURROUND BACK / PRESENCE PRE OUT jacks may not correspond to the location of the speakers connected through SURROUND BACK / PRESENCE PRE OUT jacks.
•Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level by using the remote control of this unit (see “Manually adjusting speaker levels” on page 45).
•Some signals may not be output from the SUBWOOFER jack depending on the SPEAKER SET (see page 49) and LFE LEVEL (see page 51) settings.
20
Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.
AM loop antenna |
Indoor FM antenna |
|||
(included) |
(included) |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
COMPONENT VIDEO
PR PB Y
VD
TV
NITOR OUT
TUNER
AM
ANT
GND |
MAI |
FM ANT 75Ω
UNBAL.
SURRO
SUB
WOOF
Ground (GND terminal)
For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.
CONNECTIONS
Notes
•The AM loop antenna should be placed away from this unit.
•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.
•A property installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.
■ |
75-ohm/300-ohm antenna adapter |
PREPARATION |
|
|
|||
|
(U.K. model only) |
|
|
1 |
Open the cover of the |
|
|
|
included 75-ohm/300-ohm |
|
|
|
antenna adapter. |
|
|
2 |
Cut the external sleeve |
11 (7/16) |
|
|
of the 75-ohm coaxial |
Unit: |
|
|
8 (5/16) |
||
|
|
mm (inch) |
|
|
cable and prepare it for 6 (1/14) |
||
|
connection. |
|
|
3 |
Cut the lead wire and |
|
Lead wire |
|
remove it. |
|
|
■ |
Connecting the AM loop antenna |
4 Insert the cable |
|
|
wire into the slot, |
1 |
Set up the AM loop antenna, then connect it |
and clamp it with |
|
to the terminals on this unit. |
pliers. |
Clamp |
Clamp |
|
Insert the wire into slot.
5Snap the cover into place.
2Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.
3Orient the AM loop antenna for the best reception.
■FREQUENCY STEP switch (Asia and General models only)
Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (locating on the rear panel) according to the frequency spacing in your area.
•North, Central and South America: 100 kHz/10 kHz
•Other areas: 50 kHz/9 kHz
Before setting this switch, disconnect this unit’s AC power cord from the wall outlet.
English
21
CONNECTIONS
■ Connecting the AC power cord
(U.S.A. and Canada models)
Plug the power cord into the AC inlet after all other connections are complete, then plug the power cord to an AC wall outlet.
CAUTION
AC OUTLETS |
(U.S.A. model)
VOLTAGE SELECTOR
VOLTAGE SELECTOR
2
Do not use other AC power cords. Use the one provided. Use of other power cords may result in fire hazard or electrical shock.
(Other models)
Plug the power cord into an AC wall outlet.
■ AC OUTLET(S) (SWITCHED)
U.K. and Australia models |
.............................. 1 OUTLET |
Korea model............................................................... |
None |
Other models.................................................. |
2 OUTLETS |
Use these outlets to connect the power cords from your other components to this unit. Power to the AC OUTLETS(S) is controlled by this unit’s STANDBY/ON (or SYSTEM POWER and STANDBY). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLETS(S) is:
Asia and General models |
.......................................... 50 W |
Korea model................................................................. |
N/A |
Other models ........................................................... |
100 W |
■VOLTAGE SELECTOR
(Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/230240 V AC, 50/60 Hz.
■ Memory back-up
The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However if the power cord is disconnected from the AC wall outlet, or the power supply is cut for more than one week, the stored data will be lost.
(Asia and General models)
22
CONNECTIONS
Speaker impedance setting |
|
Turning on the power |
|
|
|
|
When all connections are complete, turn on the power of |
CAUTION |
|
||
|
|
this unit. |
|
|
|
|
If you are using 6 ohm speakers, set the impedance to 6 ohms as follows before turning on the power.
Be sure this unit is in the standby mode.
1On the front panel, while pressing down SPEAKERS A, press STANDBY/ON.
“SP IMP.SET” appears on the front panel display for a few seconds, then “Minimum 8ohms” appears.
1
|
|
|
|
|
|
|
|
|
|
VOLUME |
|
|
|
INPUT |
|
|
|
|
|
|
|
|
STANDBY |
|
|
|
|
|
|
|
|
|
|
/ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
PRESET/ |
PRESET |
|
|
TUNING |
|
|
|
|
|
A/B/C/D/E |
TUNING |
/TUNING |
FM/AM |
MEMORY |
MODE |
|
PROGRAM |
|
|
|
TUNER |
|
|
|
|
|
|
|
SPEAKERS |
MULTI CH |
INPUT MODE |
|
|
|
MAN'L/AUTO FM |
AUTO/MAN'L MONO |
TONE CONTROL |
|
|
A |
B |
INPUT |
|
|
|
|
STRAIGHT |
|||
|
|
|
DSP |
|
|
|
|
|
|
EFFECT |
|
|
|
|
|
SILENT |
|
|
VIDEO AUX |
|
SPEAKERS
A |
|
|
|
(U.S.A. model) |
STANDBY |
|
|
|
|
|
|
|
|
|
/ON |
|
|
|
|
|
TRANSMIT |
|
RE–NAME CLEAR LEARN |
|
1 |
SYSTEM |
|
|
|
POWER |
STANDBY |
SLEEP |
INPUT MODE |
|
PHONO |
TUNER |
CD |
MULTI CH IN |
|
|
V-AUX |
CBL/SAT |
MD/TAPE |
CD-R |
|
DTV |
VCR 1 |
DVR/VCR2 |
DVD |
SP IMP.SET |
|
|
|
SELECT |
|
POWER |
|
POWER |
AMP |
|
TV |
|
AV |
|
REC
PREPARATION
Minimum 8ohms
2Press SPEAKERS A or SPEAKERS B to select the impedance of your speakers.
You can select either 6 ohms or 8 ohms.
3Press STANDBY/ON to exit the setting.
This unit will be set to the standby mode.
y
You can also use SP IMP.SET (see page 57) to set the speaker impedance.
1Press STANDBY/ON (SYSTEM POWER on the remote control) to turn on the power of this unit.
|
SYSTEM |
|
POWER |
STANDBY |
or |
/ON |
|
Front panel |
Remote control |
2Turn on the video monitor connected to this unit.
English
23