Samsung NA10AZ000G, NA10AZ000J, NA10AQ0001, NA10AH0046, NA10DH008K User Manual

Notice and Safety No Wireless - English V1.1.fm Page i Friday, May 3, 2002 3:07 PM

Notices

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical photocopying, recording or
otherwise, without the prior written permission of the manufacturer.

The information within this manual is subject to change without notice.

The manufacturer shall not be held liable for technical or editorial errors or omissions
contained in herein; nor for incidental or consequential damages resulting from
thefurnishing, performance or use of this material.

Microsoft Windows is a registered trademark of the Microsoft Corporation.

Product names mentioned herein are for identification purposes only, and may be
trademarks and/or registered trademarks of their respective companies.

Macrovision Statement

If your computer has a DVD drive and an analog TV Out port, the following
paragraph applies:

This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.

Copyright 2002 All rights are reserved

Notices i

Notice and Safety No Wireless - English V1.1.fm Page ii Friday, May 3, 2002 3:07 PM

Important Safety Information

Safety Instructions

Your system is designed and tested to meet the latest standards for safety of
information technology equipment. However, to ensure safe use of this product, it is
important that the safety instructions marked on the product and in the documentation
are followed.

Always follow these instructions to help guard against personal injury and
damage to your system.

i

Setting Up your System

• Read and follow all instructions marked on the product and in the

documentation before you operate your system. Retain all safety and operating
instructions for future use.

• Do not use this product near water or a heat source such as a radiator.

• Set up the system on a stable work surface.

• The product should be operated only with the type of power source indicated on

the rating label.

• Ensure that the electrical outlet you are using to power your equipment is easily

accessible in case of fire or short circuit.

• If your computer has a voltage selector switch, make sure that the switch is in

the proper position for your area.

• Openings in the computer case are provided for ventilation. Do not block or

cover these openings. Make sure you provide adequate space, at least 6 inches
(15 cm), around the system for ventilation when you set up your work area.
Never insert objects of any kind into the computer ventilation openings.

• Ensure that the fan vents on the bottom of the casing are clear at all times. Do

not place the computer on a soft surface, doing so will block the bottom vents.

• If you use an extension cord with this system, make sure that the total ampere

rating on the products plugged into the extension cord does not exceed the
extension cord ampere rating.

ii Users Manual

Notice and Safety No Wireless - English V1.1.fm Page iii Friday, May 3, 2002 3:07 PM

Care During Use

• Do not walk on the power cord or allow anything to rest on it.

• Do not spill anything on the system. The best way to avoid spills is to not eat or

drink near your system.

• Some products have a replaceable CMOS battery on the system board. There is

a danger of explosion if the CMOS battery is replaced incorrectly. Replace the
battery with the same or equivalent type recommended by the manufacturer.
Dispose of batteries according to the manufacturer’s instructions. If the CMOS
battery requires replacement insure that a qualified technician performs the task

• When the computer is turned off, a small amount of electrical current still flows

through the computer. To avoid electrical shock, always unplug all power
cables, remove the battery and modem cables from the wall outlets before
cleaning the system.

• Unplug the system from the wall outlet and refer servicing to qualified

personnel if:

– The power cord or plug is damaged.
– Liquid has been spilled into the system.
– The system does not operate properly when the operating instructions are

followed.
– The system was dropped or the casing is damaged.
– The system performance changes.

Replacement Parts and Accessories

Use only replacement parts and accessories recommended by manufacturer.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunications

line cord.

Do not use this product in areas classified as hazardous. Such areas include

patient care areas of medical and dental facilities, oxygen rich environments,

Writtenby:Daryl L. Osden

or industrial areas.

Battery Disposal

Do not put rechargeable batteries or products powered by non-removable

rechargeable batteries in the garbage.

Contact the Samsung Helpline for information on how to dispose of batteries that you
cannot use or recharge any longer.

Follow all local regulations when disposing of old batteries.

Important Safety Information iii

Notice and Safety No Wireless - English V1.1.fm Page iv Friday, May 3, 2002 3:07 PM

Laser Safety

All systems equipped with CD or DVD drives comply with the appropriate safety
standards, including IEC 825. The laser devices in these components are classified as
“Class 1 Laser Products” under a US Department of Health and Human Services
(DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact
an authorized service location.

Laser Safety Note:

Use of controls or adjustments or performance of procedures other than those

specified in this manual may result in hazardous radiation exposure. To

prevent exposure to laser beams, do not try to open the enclosure of a CD or

DVD drive.

Power Cord Requirements

The power cord set (wall plug, cable and AC adapter plug) you received with your
computer meets the requirements for use in the country where you purchased your
equipment.

Power cord sets for use in other countries must meet the requirements of the country
where you use the computer. For more information on power cord set requirements,
contact your authorized dealer, reseller, or service provider.

General Requirements

The requirements listed below are applicable to all countries:

• The length of the power cord set must be at least 6.00 feet (1.8m) and a

maximum of 9.75 feet (3.0m).

• All power cord sets must be approved by an acceptable accredited agency

responsible for evaluation in the country where the power cord set will be used.

• The power cord set must have a minimum current capacity of 7 A and a

nominal voltage rating of 125 or 250 volts AC, as required by each country’s
power system.

The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC
320 Standard Sheet C13 connector, for mating with appliance inlet on the computer.

iv Users Manual

Notice and Safety No Wireless - English V1.1.fm Page v Friday, May 3, 2002 3:07 PM

Regulatory Compliance Statements

United States of America

Unintentional Emitter per FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to Part 15 of the FCC Rules. These limits are

Writtenby:Daryl L. Osden

If necessary, the user should consult the dealer or an experienced radio/television
technician for additional suggestions. The user may find the following booklet helpful:
“Something About Interference.” This is available at FCC local regional offices. Our
company is not responsible for any radio or television interference caused by
unauthorized modifications of this equipment or the substitution or attachment of
connecting cables and equipment other than those specified by our company. The
correction will be the responsibility of the user. Use only shielded data cables with this
system.

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generate uses and can radiate radio

frequency energy and if not installed and used in accordance with the

instructions may cause harmful interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Part 68

This equipment compiles with part of the FCC rules. On the back of this equipment is
a label that contains, among other information, the FCC registration number and ringer
equivalence number (REN) for this equipment. If requested, this information must be
provided to the telephone company.

Regulatory Compliance Statements v

Notice and Safety No Wireless - English V1.1.fm Page vi Friday, May 3, 2002 3:07 PM

This equipment uses the following USOC jacks : RJ11C

An FCC compliant telephone cord and modular plug is provided with this equipment.
This equipment is designed to be connected to the telephone network or promises
wiring using a compatible modular jack which is Part 68 compliant. See Installation
Instructions for details.

The REN is used to determine the quantity of devices which may be connected to
telephone line. Excessive RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most, but not all areas, the sum of RENs
should not exceed five(5.0). To be certain of the number of devices that may be
connected to a line, as determined by total RENs, contact the local telephone company
to determine the maximum REN for the calling area.

If the terminal equipment causes harm to the telephone network, the Telephone
Company will notify you in advance that temporary discontinuance of service may be
required. But if advance notice is not practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of the equipment. If this happens, the
telephone company will provide advanced notice in order for you to make necessary
modifications to maintain uninterrupted service.

If trouble is experienced with this equipment (Modem) for repair or warranty
information, please contact your local distributor. If the equipment is causing harm to
the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.

The user must use the accessories and cables supplied by the manufacturer to get
optimum performance from the product.

No repairs may be done by the customer.

This equipment cannot be used on public coin phone service provided by the telephone
company. Connection to party line service is subject to state tariffs.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to
use a computer or other electronic device, including fax machines, to send any message
unless such message clearly contains in a margin at the top or bottom of each
transmitted page or on the first page of the transmission, the date and time it is sent and
an identification of the business or other entity, or other individual sending the message
and the telephone number of the sending machine or such business, other entity, or
individual. (The telephone number provided may not be any number for which charges
exceed local or long-distance transmission charges.)

In order to program this information into your fax machine, refer to your
communications software user manual.

vi Users Manual

Notice and Safety No Wireless - English V1.1.fm Page vii Friday, May 3, 2002 3:07 PM

Canada

Industry Canada (IC)

Unintentional Emitter per ICES-003

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the radio interference regulations of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement
sur le brouillage radioélectrique édicté par Industrie Canada.

Telecommunications per DOC notice
(for products fitted with an IC-compliant modem)

The Industry Canada label identifies certified equipment. This certification means that
the equipment meets certain telecommunications network protective, operation, and
safety requirements. The Department does not guarantee the equipment will operate to
the users’ satisfaction.

Before installing this equipment, users should make sure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. In some cases, the
inside wiring associated with a single-line individual service may be extended by
means of a certified connector assembly. The customer should be aware that
compliance with the above conditions may not prevent degradation of service in some
situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.

Users should make sure, for their own protection, that the electrical ground connections
of the power utility, telephone lines, and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.

To avoid electrical shock or equipment malfunction do not attempt to make

electrical ground connections by yourself. Contact the appropriate inspection

authority or an electrician, as appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides
an indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5.

Regulatory Compliance Statements vii

Notice and Safety No Wireless - English V1.1.fm Page viii Friday, May 3, 2002 3:07 PM

European Union

The following information is only applicable to systems labeled with the CE mark .

European Directives

This Information Technology Equipment has been tested and found to comply with the
following European directives:

• EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/

EEC as per

– EN 55022 Class B

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

• Low Voltage Directive (Safety) 73/23/EEC as per EN 60950(A1/A2/A3/A4/

A11)

• Radio and Telecom Terminal Equipment Directive 199/5/EC as per

– CTR21 (if fitted with a modem device)

European Telecommunication Information
(for products fitted with EU-approved modems)

Marking by the symbol indicates compliance of this equipment to the Radio and
Telecom Terminal Equipment Directive 1999/5/EC. Such marking is indicative that
this equipment meets or exceeds the following technical standards:

CTR 21 – Attachment requirements for pan-European approval for connection to the
analogue Public Switched Telephone Networks (PSTNs) of TE (excluding TE
supporting voice telephony services) in which network addressing, if provided, is by
means of Dual Tone Multi-Frequency (DTMF) signaling.

Although this equipment can use either loop disconnect (pulse) or DTMF

(tone) signaling, only the performance of the DTMF signaling is subject to

regulatory requirements for correct operation. It is therefore strongly

recommended that the equipment is set to use DTMF signaling for access to

public or private emergency services. DTMF signaling also provides faster call

setup.

This equipment has been approved to Council Decision 98/482/EEC—“CTR 21” for
Pan-European single terminal connection to the Public Switched Telephone Network
(PSTN).

However, due to differences between the individual PSTNs provided in different
countries, the approval does not, of itself, give an unconditional assurance of
successful operation on every PSTN termination point. In the event of problems, you
should contact manufacturer Technical Support.

viii Users Manual

Notice and Safety No Wireless - English V1.1.fm Page ix Friday, May 3, 2002 3:07 PM

Japan

VCCI Statement

This equipment is in the Class B category (Information Technology Equipment to be
used in a residential area or an adjacent area thereto) and conforms to the standards set
by the Voluntary Control Council for Interference by Information Technology
Equipment aimed at preventing radio interference in such residential areas. When used
near a radio or TV receiver, it may become the cause of radio interference. Read
instructions for correct handling.

Regulatory Compliance Statements ix

LEO II (2) (Windows XP) - English.fm Page 1 Wednesday, June 19, 2002 3:36 PM

Using Your Documentation

Congratulations on your purchase of a notebook computer with the Windows® XP
operating system. Whether you are new to using a portable computer or are an
experienced user, this user’s manual can help you get the most from your computer.

Manual Documentation Conventions

Information Icons

Three icons and their associated messages appear in this manual. The information
icons are placed before the step/information they apply to:

Warning:

Indicates the possibility of personal injury.

Caution:

Warns you of possible damage to equipment or data.

Note:

Informs you of special circumstances.

Technical Information:

Informs you of special requirements or limitations for use of item(s).

Keyboard Conventions

Keys that you need to press to perform certain functions are displayed in the manual
using a small graphic of the button. For example: <Ctrl>

or <Ctrl> indicates the control key (Ctrl on the keyboard).

If you need to press two keys at the same time, the key names are shown joined by a
plus sign. For example:

Mute

+

means that you should press the Fn key and hold it and then press the F8 key.

or <Fn+F8>

Using Your Documentation 1

LEO II (2) (Windows XP) - English.fm Page 2 Wednesday, June 19, 2002 3:36 PM

CD-ROM Device Naming Convention

In many installation programs you will have to get a program from the CD-ROM
device. The program installation sequence assumes that the CD is drive d:\, however
this is not always the case. The name of the CD-ROM drive is the letter following the
letter assigned to your last HDD. For instance, if you have one HDD with two
partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.

Touchpad Conventions

You may be asked to click or double-click on items on the display screen. As a general
note the touchpad actions act much in the same way as a wheel mouse, any differences
are explained fully.

The object that needs to be clicked upon will be displayed in Bold text or shown in a
small figure such as the “Start Button” shown on the right => .

Table 1. Touchpad Click Conventions

Action Process

Click Depress the touchpad left button and release

Double-Click Quickly click the left touchpad button two times

Almost all "Windows" programs will display the name/function of a button or

icon if you place the touchpad pointer on the item you want information about.

Software User Documentation

Your computer is shipped from the factory with several software programs installed.
The software may include its own online or printed documentation. Refer to the
documentation or the Help options in the software for more information.

The figures and illustrations in this manual may not be identical to those on

your system.

General Icon Note:

Some of the Icons used in Windows XP may be placed on the taskbar by

selecting (ex: Place the volume icon in the taskbar) in the properties dialog

box.

2 Users Manual

LEO II (2) (Windows XP) - English.fm Page 3 Wednesday, June 19, 2002 3:36 PM

Introducing Your Computer

Your computer is a lightweight portable computer that includes a CD-ROM drive and
a floppy drive plus many features to meet your computing needs at home and/or on the
road.

Where Everything Is

The next 6 figures will explain the location of all of the buttons, LEDs and equipment
needed to operate your notebook computer.

Front

Touchpad

Speaker

LCD Display

SENS

Keyboard

LEDs

Keyboard

Touchpad Buttons

LCD Latch

Speaker

Power Button

Introducing Your Computer 3

LEO II (2) (Windows XP) - English.fm Page 4 Wednesday, June 19, 2002 3:36 PM

Buttons & LEDs

Power Button

Internet Button

E-Mail Button

User Programmable

Button

Right Side

Left Side

Battery

Volume Wheel

Scroll Lock LED

Caps Lock LED

Num Lock LED

Disk Access LED

Fan Vent DC-In PortFDD Drive

Battery Status LED

Power LED

4 Users Manual

CD-ROM Drive PCMCIA Slot (2)

LEO II (2) (Windows XP) - English.fm Page 5 Wednesday, June 19, 2002 3:36 PM

Back Side

Security Lock Port

USB Port

Modem Port

PS/2 Port

USB Ports (2)

Microphone Jack

LAN Port

Parallel Printer Port

Serial Port

External Monitor Port

VHS TV Out Port

Headphone Jack

Bottom

Fan Vent

Battery Latch

HDD Compartment

Battery

Computer Cooling:

Ensure that the fan vents on the bottom of the casing are clear at all times. Do

not place the computer on a soft surface, doing so will block the bottom vents.

Introducing Your Computer 5

LEO II (2) (Windows XP) - English.fm Page 6 Wednesday, June 19, 2002 3:36 PM

Using Your Computer for the First Time

This section gives you detailed information on using your computer for the first time.

Installing the Battery

Proceed as follows to install the battery pack:

1. With the computer’s power off, close the LCD panel and turn the computer over

so the bottom of the unit faces up.

Battery Orientation:

Insert the battery into the battery compartment, ensuring the correct

orientation so that the battery fits in its slot properly.

Battery

Battery Latch

2. Carefully slide the battery pack into the compartment. Make sure the battery is
fully inserted into the compartment. You will hear the battery latch click which
will secure the battery in place.

6 Users Manual

LEO II (2) (Windows XP) - English.fm Page 7 Wednesday, June 19, 2002 3:36 PM

AC Adapter

Your computer runs on power from the battery in the computer or from an electrical
outlet. The first time that you use your computer, fully charge the battery using the AC
adapter.

To attach the power cord complete the following:

Power Cords:

Many countries have different power cord configurations. Your computer
should be supplied with the correct one for your area. If not contact the
supplier.

1. Plug the AC adapter into the power connector on the side of the computer.

2. Connect the power cord to the AC adapter and then to an electrical outlet.

DC-in Port

AC Adapter

DC Output Cable

Power Cord

The battery starts charging as soon as you plug the power cord into an electrical outlet.
The battery charges faster if the computer is turned off during charging.

Ensure you charge the battery fully the first time you use it.

See ”Using the Battery” on page 32 for more information on using your computer’s
battery.

Using Your Computer for the First Time 7

LEO II (2) (Windows XP) - English.fm Page 8 Wednesday, June 19, 2002 3:36 PM

Turning On the Computer

To turn on the computer’s power for the first time:

1. Slide the LCD latch, located on the front of the cover to the right.

2. Lift up the LCD display.

Power
Button

3. Press and then release the power button.

The power LED is on when the computer’s power is on.

Initial Computer Startup:

The first time you start your computer you will see the operating system
registration screens. Simply read each screen and follow the simple directions.

You must complete this process in order to use your computer. A tutorial is
provided if you require it.

8 Users Manual

LEO II (2) (Windows XP) - English.fm Page 9 Wednesday, June 19, 2002 3:36 PM

Turning Off Your Computer

Prior to shutting down your computer ensure all of your data and current work are
saved. The system will ask if you wish to save any unsaved work, saving your work
first will speed the shutdown process.

To turn off the computer, complete the following steps:

1. Click on the taskbar.

If you need to restart your computer after software (re)installation or because it is not
responding, select the Restart option in step 3 below.

2. Click Shut Down Computer to display the shutdown popup window shown
below.

3. Click Turn Off to complete the shutdown sequence.

If the system does not power off, then press and hold the power button for over
4 seconds.

See ”Using Power Management Options” on page 43.

You can also perform a soft boot by saving your files and pressing <Ctrl+Alt+Del> to
pop-up the “Windows Task Manager” window. Click Shut Down > Restart.

You can perform a cold boot by pressing the power button for more than 4 seconds to
turn the computer off, waiting more than 5 seconds, and then pressing the power button
to turn the computer on.

The power button has several functions other than just turning on and off your
computer, see “Using Power Management Options” on page 43.

Using Your Computer for the First Time 9

LEO II (2) (Windows XP) - English.fm Page 10 Wednesday, June 19, 2002 3:36 PM

Using the LCD Display

This section will discuss using/changing the LCD display:

The LCD display brightness adjustment is divided into 6 levels.

• The <Fn+F9> key combination decreases LCD brightness.

• The <Fn+F10> key combination increases LCD brightness.

The LCD display will automatically dim when you remove AC power to conserve
battery power. If required, adjust the LCD brightness to a higher level when you are on
battery power, however this will decrease battery life.

LCD Cleaning:

Cleaning the LCD display should only be done with a soft cloth dampened with
denatured alcohol or a proprietary LCD screen cleaner.

Even if you change the default LCD display brightness settings, the defaults
listed above will be restored once you power off and then back on.

Notice: The limits of LCD manufacturing technology allow a maximum of 10

abnormal/bad pixels.

10 Users Manual

LEO II (2) (Windows XP) - English.fm Page 11 Wednesday, June 19, 2002 3:36 PM

Tips for Using Your Computer

The following information helps you avoid potential problems as you use your
computer:

Do not try to disassemble your computer. Opening the system chassis voids
your warranty. Only an authorized manufacturer service center can replace or
add any parts inside the chassis.

• Follow all the instructions and cautions in your computer user documentation.

• The LCD display has a polarized surface and can be damaged easily. To

prevent damage, avoid touching the LCD display screen.

• Because a notebook computer is small and has restricted air flow around

components, it is more likely to overheat than a desktop computer. A fan inside
your computer runs when needed to help eliminate heat. Make sure the fan vent
on the right side of your computer is not blocked when you use the computer.
Occasionally check the vents and remove any accumulated dust on the outside.

• Use only approved AC adapters, auto adapters, memory modules and other

options.

• Avoid using or storing the computer in extremely hot or cold areas, such as a

car on a hot day. Keep the computer away from heaters and out of direct
sunlight. Exposure to excessive heat may damage computer components.

• If you have left your computer in a hot place, let it cool down slowly to room

temperature (with the LCD panel open) before using it.

• Set up your computer work area to avoid physical strain. Sit with your back

straight and supported by your chair. Adjust your chair or work table so that
your arms and wrists can remain in a relaxed position, parallel with the floor.
Avoid bending or twisting your wrists as you work. Your hands should “float”
slightly above the keyboard. Refer to a book on office ergonomics for more
information on setting up your work area.

• Take frequent breaks from working at the computer to rest your eyes and

stretch your muscles.

• Remember to save your data files frequently and to make backup copies of your

files.

Using Your Computer for the First Time 11

LEO II (2) (Windows XP) - English.fm Page 12 Wednesday, June 19, 2002 3:36 PM

Travelling with Your Computer

Air Travel

If you are travelling by air, follow these tips:

• Take the computer with you as carry-on luggage. Do not check the computer

with your baggage.

• Allow the computer and disks to go through the X-ray security devices. Do not

hand-carry disks through the walk-through metal detectors, which can cause
loss of data.

• Make sure that the battery is charged or the power cord is easily accessible.

You may be required to turn on the computer for airport security personnel.

• Be prepared to turn off the computer during take off and landing.

Locking your Computer

As a precaution when you are travelling or using your computer in an unsecured area,
you should keep your computer as safe as possible. An option to do this is the Security
Lock System. Follow the Security Lock System manufacturers instructions for specific
installation and use. The following figure shows generally how to use the lock.

To LockFrom Lock

12 Users Manual

LEO II (2) (Windows XP) - English.fm Page 13 Wednesday, June 19, 2002 3:36 PM

Handling Spills

Spill Caution:

Sweet liquids leave a sticky residue that may damage the keyboard and
internal parts despite your efforts to dry it.

Some liquids will damage the polarized LCD screen. If your screen is
damaged, contact your authorized manufacturer’s service center for a
replacement.

Do not spill anything on your computer. The best way to avoid spills is to not
eat or drink around your computer. If you do spill something on your computer,
turn it off and unplug it immediately, then do the following:

• If you spill liquid on the keyboard, drain as much of the liquid from the

keyboard as possible. Be careful not to let the liquid drip onto the LCD panel.
Allow the system to dry for several days before trying to use it.

• If you spill liquid on an external keyboard or keypad, unplug it and drain as

much of the liquid as possible. Allow the keyboard to sit at room temperature
for a full day before trying to use it.

• If you spill liquid on the LCD panel, clean it immediately with a soft cloth and

denatured alcohol
cleaner, acetone, aromatic solvent, or dry, rough towels to clean it.

or a proprietary LCD screen cleaner. Do not use water, window

Using Your Computer for the First Time 13

LEO II (2) (Windows XP) - English.fm Page 14 Wednesday, June 19, 2002 3:36 PM

Using the Keyboard

Your computer has an 88-key keyboard. By pressing designated key combinations, you
can have access to all the key functions of a full-sized keyboard.

Country Specific Keyboards:

Keyboard configuration is different from one country to another, however the
operation of the keys and key combinations remain the same.

Function & Special Purpose Keys

Backlit

Backlit

Embedded
Numeric Keypad

Function

Key

Although the layout of the keys on your computer’s keyboard is different from that on
a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you
use it.

The keys on the keyboard can be grouped into the following categories:

14 Users Manual

Application

Key

Windows

Key

Cursor/Screen

Control Keys

• Full-sized Alphanumeric typewriter keys are arranged like a standard

typewriter keyboard [QWERTY] and are used for text entry. The Windows key
opens Windows menus and performs other special functions.

• F1, F2, F4, F5 and F8 to F12 when pressed together with, enable special

functions.

• The Application key is used for quick access to shortcut menus and help

assistants in Windows.