INSTALLATION MANUAL
AVH-P7850DVD
This product conforms to new cord colors.
Los colores de los cables de este producto se conforman con un nuevo código de colores.
As cores dos fios deste produto seguem um novo padrão de cores.
|
English |
MANUAL INSTALLATION |
Nederlands Italiano (B) Português Español |
|
|
Contents |
|
Connecting the Units ................................ |
1 |
Connecting the system ...................................... |
3 |
Connecting the power cord (1) .......................... |
5 |
Connecting the power cord (2) .......................... |
7 |
When connecting to separately sold power |
|
amp ............................................................ |
9 |
When connecting with a rear view camera |
.... 11 |
When connecting the external video |
|
component and the display ...................... |
13 |
Installation ................................................ |
15 |
Installing the hide-away unit .......................... |
15 |
DIN Front/Rear-mount .................................... |
16 |
DIN Front-mount ............................................ |
16 |
DIN Rear-mount .............................................. |
17 |
Installing the remote control unit .................... |
18 |
WARNING:
•To avoid the risk of accident and the potential violation of applicable laws, the front DVD or TV (sold separately) feature should never be used while the vehicle is being driven. Also, Rear Displays should not be in a location where it is a visible distraction to the driver.
•In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and this unit’s DVD features should not be used.
•If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly.
Connecting the Units
CAUTION:
•PIONEER does not recommend that you install or service your display yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to authorized Pioneer service personnel.
•Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed.
•Do not drill a hole into the engine compartment to connect the yellow lead of the unit to the vehicle battery. Engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. Take extra care in securing the wire at this point.
•It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift. Be sure to install the display in such a way that it will not obstruct driving.
•Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, parking brake or seat sliding mechanism.
•Do not shorten any leads. If you do, the protection circuit may fail to work properly.
1
Note:
•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage.
•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.
•Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.
•Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.
•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.
•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.
•Do not shorten any leads. If you do, the protection circuit may fail to work when it should.
•Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.
•When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.
•Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common.
•Speakers connected to this unit must be highpower with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged.
•When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.
•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction.
•To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not insulated.
•To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly.
•This unit cannot be installed in a vehicle that does not have an ACC (accessory) position on the ignition switch. (Fig. 1)
|
|
CC |
|
|
|
|
|
|
|
|
|
F |
A |
O |
|
|
|
F |
O |
|
|
|
F |
|
N |
|
N |
|||||
O |
|
|
|
|
O |
F |
|
|
|
|
|
|
|
|
S |
|
|
|
S |
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
T |
|
|
|
|
T |
|
|
|
T |
R |
A |
|
|
|
R |
A |
|
|
|
|
|
|
T |
|
|||
ACC position |
No ACC position |
Fig. 1
•The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps.
If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.
•Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the
same function.
PyТТНЛИ Nederlands Italiano Franзais Deutsch Espaсol English
2
Connecting the Units
Connecting the system
Antenna jack |
Blue |
|
|
Antenna cable (supplied) |
|
IP-BUS input |
|
|
AV-BUS input (Blue) |
|
|
(Blue) |
|
|
|
6 m |
|
|
|
Blue |
Blue |
Violet |
|
Hide-away unit (supplied) |
|
|
|
6 m |
|
|
6 m |
IP-BUS cable |
|
|
(supplied with XDV-P650) |
|
AV-BUS cable (supplied |
|
|
|
with XDV-P650) |
|
Blue |
Black |
|
|
||
|
|
|
XDV-P650 |
|
Blue |
|
(sold separately) |
|
|
|
|
IP BUS |
STAND ALONE |
Black |
|
|
|
Hide-away unit |
Black |
(supplied with XDV-P650) |
Black |
|
Black |
Black
25 pin cable (supplied with XDV-P650) Depending on where you install,
this cable is not used.
AV-BUS cable (supplied with TV tuner)
3
1.5 m
This product |
15 cm |
40 cm
40 cm
Blue
Violet Optical cable
(e.g. CD-AD600) (sold separately)
Microphone/auxiliary input jack (3.5 ø) (MIC/AUX IN)
Before installing this unit to your vehicle, pull out the jack to the place where you can easily plug in/out the microphone or stereo mini plug cable. Use a stereo mini plug cable to connect with auxiliary equipment.
Blue |
1 m |
Power supply box (supplied)
Deutsch Español English
30-pin cable (supplied)
30-pin cable (supplied)
Hide-away TV tuner (e.g. GEX-P5750TV(P)) (sold separately)
IP-BUS cable (supplied with TV tuner)
IP-BUS cable
Black |
Blue |
Black
Français
Multi-CD player
(sold separately) Italiano
Nederlands
PyТТНЛИ
Fig. 2
4
Connecting the Units
Connecting the power cord (1)
If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly.
Black (ground)
To vehicle (metal) body.
Yellow
After making all other connections to this unit, connect this to the positive + terminal of the battery.
CAUTION
Attach a 20A fuse immediately prior to the battery. Also, use heat resistant battery cable with more than 5-square millimeter sectional area.
Red
To electric terminal controlled by ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
5
This product
Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections.
Fuse (7.5 A)
Fuse resistor
Fuse resistor
Power supply box (supplied)
PyТТНЛИ Nederlands Italiano Franзais Deutsch Espaсol English
Fig. 3
6
Connecting the Units
Connecting the power cord (2)
If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly.
Hide-away unit (supplied)
Connect when the audio settings of this product are used in the network mode.
Left |
|
|
Right |
|
Tweeter |
White |
Gray |
Tweeter |
|
+ |
||||
+ |
||||
(FRONT HIGH |
(FRONT HIGH |
|||
≠ |
≠ |
|||
OUTPUT) |
OUTPUT) |
|||
|
White/black |
Gray/black |
|
Front center speaker |
Black/white |
Black/white |
Rear center speaker |
|
+ |
+ |
|||
(FRONT CENTER |
≠ |
≠ |
(REAR CENTER |
|
OUTPUT) |
OUTPUT) |
|||
Black |
Black |
|||
|
|
|||
|
White |
Gray |
|
|
|
|
|
||
Front speaker |
+ |
+ |
Front speaker |
|
(MID/FRONT |
≠ |
≠ |
(MID/FRONT |
|
OUTPUT) |
White/black |
Gray/black |
OUTPUT) |
|
|
Green |
Violet |
|
|
Rear speaker |
+ |
+ |
Rear speaker |
|
|
|
|||
|
≠ |
≠ |
|
|
|
Green/black |
Violet/black |
|
7
See the section “When Violet/white connecting with a rear view
camera”.
WARNING
LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Connection method
1. Clamp the lead. |
2. Clamp firmly with |
|
needle-nosed |
|
pliers. |
Note:
•The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side of the parking brake switch.
Power supply side |
Parking brake |
Ground side |
switch |
|
Blue/white
To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC).
|
Yellow |
|
After making all other connections to this unit, |
Fuse (4 A) |
connect this to the positive + terminal of the |
|
battery. |
|
CAUTION |
Fuse (10 A)
Fuse (10 A)
Black (ground)
To vehicle (metal) body.
Attach a 20A fuse immediately prior to the battery. Also, use heat resistant battery cable with more than 5-square millimeter sectional area.
Fig. 4
PyТТНЛИ Nederlands Italiano Franзais Deutsch Espaсol English
8
Connecting the Units
When connecting to separately sold power amp
Hide-away unit (supplied)
See the section “Connecting the power cord (2)”.
Blue/white
To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC).
System remote control
Connect when the audio settings of this product are used in the network mode.
9
Power amp (sold separately)
Power amp (sold separately)
Power amp
(sold separately) RCA cables
(sold separately)
Power amp (sold separately)
Power amp (sold separately)
Power amp (sold separately)
Front center speaker |
|
Left |
Right |
Tweeter |
Tweeter |
Front middle range |
Front middle range |
speaker |
speaker |
Rear speaker |
Rear speaker |
Subwoofer |
|
Rear center speaker |
|
Fig. 5
PyТТНЛИ Nederlands Italiano Franзais Deutsch Espaсol English
10
Connecting the Units
When connecting with a rear view camera
When using this product with a rear view camera, automatic switching to video from a rear view camera when the gear shift is moved to REVERSE (R) position is possible.
WARNING:
•USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
CAUTION:
•The screen image may appear reversed.
•The rear view camera function is to use this product as an aid to keep an eye on trailers, or backing into a tight parking spot. Do not use this function for entertainment purposes.
•The object in rear view may appear closer or more distant than in reality.
11
RCA cable
(sold separately)
Rear view camera
To video output
Hide-away unit (supplied)
See the section
“Connecting the power cord (2)”.
CAUTION
Pioneer recommends the use of a camera which outputs mirror reversed images, otherwise screen image may appear reversed.
|
8 m |
Extension lead (supplied) |
15 cm |
|
|
|
|
|
Violet/white |
|
Fuse resistor |
Of the two lead wires connected to the |
|
|
back lamp, connect the one in which the |
|
|
voltage changes when the gear shift is in |
|
|
the REVERSE (R) position. |
|
|
Connection method |
|
|
1. Clamp the lead. |
|
2. Clamp firmly with |
needle-nosed pliers.
Note:
•It is necessary to set to AV INPUT2 in SETUP when connecting the rear view camera.
PyТТНЛИ Nederlands Italiano Franзais Deutsch Espaсol English
Fig. 6 |
12 |
Connecting the Units
When connecting the external video component and the display
|
To video input |
|
Display with |
Hide-away unit |
RCA input jacks |
|
|
|
To audio inputs |
RCA cables (sold separately)
Video input 2 |
Video input 1 |
To audio outputs
External video component (sold separately)
To video output
Fig. 7
•It is necessary to set to AV INPUT1 and AV INPUT2 in SETUP when connecting the external video component.
When using a display connected to rear video output
This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the DVD or Video CD.
WARNING:
•NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while Driving.
•NEVER connect rear audio output (REAR DISPLAY OUT) to sold separately power amp.
13
About video input 1
Depending on the unit connected to this unit, video image may be distorted. In this case, eliminate the distortion by adjusting the video image selecting switch on the underneath of the hide-away unit to the appropriate position. Use a thin standard-tip screwdriver to adjust the video image selecting switch on the underneath of the hide-away unit.
Español English
Fig. 8
PyТТНЛИ Nederlands Italiano Franзais Deutsch
14
Installation
Note:
•Before making a final installation of the unit, temporarily connect the wiring to confirm that the connections are correct and the system works properly.
•Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
•Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
•Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
•Do not place the display in a position where it will impede the driver’s visibility or affect the operation of your vehicle’s air bags.
•The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.
•If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. (Fig. 9)
30°
Fig. 9
•The cords must not cover up the area shown in the figure below. This is necessary to allow the amplifires to radiate freely. (Fig. 10)
Do not close this area.
Fig. 10
•When installing make sure you leave ample space (approx. 10 cm) in front of the exhaust fan outlet.
•When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.
•When mounting the hide-away unit, make sure none of the leads are trapped between the hideaway unit and the surrounding metalwork or fittings.
•Do not mount the hide-away unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it.
•Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts.
•If the hide-away unit is installed in the passenger compartment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident.
•If the hide-away unit is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit.
•Follow the instructions below when installing the power supply box.
-Keep the power supply box as far away as possible from any antenna cable.
-Do not install the power supply box where it might obstruct safe driving.
Installing the hide-away unit
Mounting with Brackets
Tapping screw (4 × 12 mm)
Car mat or chassis |
Screw |
|
Bracket |
||
(4 × 8 mm) |
Drill 2 to 2.5 mm diameter holes.
Fig. 11
15
Mounting with Velcro Tape
Thoroughly wipe off the surface before affixing the velcro tape.
Hide-away unit
Velcro tape (large) (hard)
Velcro tape (large) (soft)
Car mat or chassis
Fig. 12
DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rearmount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following illustrated installation methods.
Before installing the unit
•Remove the holder. (Fig. 13)
Loosen the screws (2 × 3 mm) and then remove the holder.
Holder
Screw (2 × 3 mm)
Fig. 13
DIN Front-mount
Installation with the rubber bush
1.Decide the position of the side brackets. (Fig. 14)
When installing in a shallow space, change the position of side brackets. In this case, stick conceal tape on parts that protrude from the dashboard.
Conceal tape
Side bracket
Flush surface screw (5 × 6 mm)
Fig. 14
PyТТНЛИ Nederlands Italiano Franзais Deutsch Espaсol English
16