AVH-P5000DVD
CAUTION
• PIONEER does not recommend that you
install or service your display yourself.
Installing or servicing the product may
expose you to risk of electric shock or
other hazards. Refer all installation and
servicing of your display to authorized
Pioneer service personnel.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
• Do not drill a hole into the engine com-
partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take extra
care in securing the wire at this point.
• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that it
will not obstruct driving.
• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work prop-
erly.
WARNING
LIGHT GREEN LEAD AT POWER CONNEC-
TOR IS DESIGNED TO DETECT PARKED
STATUS AND MUST BE CONNECTED TO
THE POWER SUPPLY SIDE OF THE PARK-
ING BRAKE SWITCH. IMPROPER CONNEC-
TION OR USE OF THIS LEAD MAY VIOLATE
APPLICABLE LAW AND MAY RESULT IN
SERIOUS INJURY OR DAMAGE.
WARNING
• To avoid the risk of accident and the potential vio-
lation of applicable laws, the front DVD or TV
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.
• In some countries or states the viewing of
images on a display inside a vehicle even by
persons other than the driver may be illegal.
Where such regulations apply, they must be
obeyed and this unit’s DVD features should
not be used.
INSTALLATION MANUAL
MANUEL D’INSTALLATION
<KMINX> <07K00000>
AVH-P5000DVD
Printed in Thailand
Imprimé en Thaïlande
<CRD4275-A/N> UC
Connecting the Units ENGLISH
Note:
• This unit cannot be installed in a vehicle with-
out ACC (accessory) position on the ignition
switch.
• Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not remove RCA caps if RCA cables are
not used.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s nega-
tive cables.
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
• Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
Parts supplied
Screw (2 mm × 5 mm)
(2 pcs.)
HolderTouch panel pen
Double-ended screwRubber bush
Side bracket (large)
(2 pcs.)
Concealing tape
Binding screw
(4 mm × 3 mm)
(4 pcs.)
Binding screw
(5 mm × 6 mm)
(4 pcs.)
Flush surface screw
(5 mm × 6 mm) (6 pcs.)
(2 are pre-installed.)
Screw (2 mm × 3 mm)
(4 pcs.) (pre-installed)
Side bracket (small)
(2 pcs.) (pre-installed)
Trim ring
(pre-installed)
Mounting sleeve
(pre-installed)
USB cable
Antenna cablePower cordTuner boxThis product
+
≠
+
≠
+
≠
+
≠
+
≠
Connection method
1. Clamp the lead.
2. Clamp firmly with
needle-nosed pliers.
Note:
• The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This
lead must be connected to the power supply side of the parking
brake switch.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal
(max. 300 mA 12 V DC).
Ground side
Power supply side
Parking brake
switch
When you connect the separately sold multi-
channel processor (e.g., DEQ-P8000) to this
unit, do not connect anything to the speaker
leads and system remote control
(blue/white).
Yellow
Connect to the constant 12 V supply terminal.
Fuse (10 A)
Fuse resistor
Red
Connect to terminal controlled by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Fuse resistor
Orange/white
Connect to lighting switch terminal.
Left Right
Front speaker Front speaker
Rear speaker or
Subwoofer (4 Ω)
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Note:
• Change the initial setting of this unit (refer to the
Operation Manual). The subwoofer output of this unit
is monaural.
Violet
Violet/black
Not used.
Green
Green/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit.
Do not connect anything to Green and Green/black leads.
Subwoofer (4 Ω)
× 2
Rear speaker or
Subwoofer (4 Ω)
Dock connector
Connect to separately sold iPod.
Interface cable (e.g., CD-I200)
(sold separately)
80 cm (2 ft. 7 in.)
Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on
that piece of equipment. If not, keep the Audio Mute lead free of any connections.
IP-BUS input
(Blue)
IP-BUS cable
Tuner box (supplied)
This product
1.5 m (4 ft. 11 in.)
20 cm (7-7/8 in.)
USB cable (supplied)
Connect to separately sold
USB device.
USB input
Antenna cable
(supplied)
Multi-CD player
(sold separately)
Gray
Wired remote input
Hard-wired remote control adaptor
can be connected (sold separately).
80 cm (2 ft. 7 in.)
++
≠≠
++
≠≠
N
ote
:
C
han
g
e the initial settin
g
of this unit (refer to the O
p
eration
M
anua
l
). T
h
e su
b
woo
f
er out
p
ut o
f
t
hi
s un
i
t
i
s monaura
l
.
This product
Power amp
(sold separately)
Power amp
(sold separately)
Connect with RCA cables
(sold separately)
Rear speaker
or subwoofer
Rear speaker
or subwoofer
Perform these connections when
using the optional amplifier.
System remote control
Front speaker Front speaker
Left Right
Front output
(FRONT OUTPUT)
Rear output or subwoofer output
(REAR/SUBWOOFER/DEQ OUTPUT)
15 cm (5-7/8 in.)
15 cm (5-7/8 in.)
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal
(max. 300 mA 12 V DC).
When you connect the separately sold multi-
channel processor (e.g., DEQ-P8000) to this
unit, do not connect anything to the speaker
leads and system remote control
(blue/white).
When you connect the multi-channel
processor to this unit, refer to multi-channel
processor’s installation manual for the
connection method.
Connecting the power cord When connecting to separately sold power amp
Connecting the Units ENGLISH
When connecting with a rear view camera
When this product is used with a rear view camera, it is possible to automatically switch
from the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
•
The screen image may appear reversed.
• The rear view camera function is to be used as an aid for backing into a tight parking spot. Do not use this
function for entertainment purposes.
• Objects in the rear view may appear closer or more distant than they actually are.
When connecting with a multi-channel processor
When you connect a separately sold
DVD player to the separetely sold
multi-channel processor, the optical
cable from DVD player must be
connected to the optical cable 2 input
(OPT. IN2) of the multi-channel
processor.
This product
25 pin cable (supplied
with DVD player)
DEQ output (REAR/
SUBWOOFER/DEQ OUTPUT)
Video input
(VIDEO INPUT)
15 cm (5-7/8 in.)
25 cm
(9-7/8 in.)
Multi-CD player
(sold separately)
IP-BUS cable
IP-BUS input (Blue)
Optical cable connection box
(supplied with multi-channel
processor)
IP-BUS cable (supplied with
multi-channel processor)
RCA cable (supplied
with DVD player)
Optical cable (sold
separately)
Optical cable (supplied with
multi-channel processor)
RCA cable (supplied with
multi-channel processor)
DVD player (e.g., XDV-P6)
(sold separately)
Black
Black
Blue
Hide-away unit (supplied
with DVD player)
Front video output
(Yellow)
IP-BUS cable
(supplied with DVD
player)
Black
Blue
Multi-channel processor
(e.g., DEQ-P8000)
(sold separately)
Black
Blue
Black Blue
You can use only one video component
with this unit.
Connecting the Units ENGLISH
Violet/white
Of the two lead wires connected to the back lamp, connect the
one in which the voltage changes when the gear shift is in the
REVERSE (R)
p
os
i
t
i
on. T
hi
s connect
i
on ena
bl
es t
h
e un
i
t t
o
sense w
h
et
h
er t
h
e car
i
s mov
i
n
g
f
orwar
d
s or
b
ac
k
war
d
s.
This product
Rear view camera input
(REAR VIEW
CAMERA IN)
Y
ou must use a camera
wh
i
ch outputs m
i
rror
reversed
i
mages
.
20 cm (7-7/8 in.)
Fuse resistor
Co
nn
ect
i
o
n m
et
h
od
1. C
l
am
p
t
h
e
l
ea
d
.
2. C
l
am
p
fi
rm
ly
w
i
t
h
nee
dl
e-nose
d
pli
ers.
N
ote:
It is necessar
y
to se
t
C
AMERA P
O
LARIT
Y
p
ro
p
erl
y
in
S
YSTEM MEN
U
w
h
e
n
connectin
g
the rear view camera.
15 cm (5-7/8 in.)
RCA cable
(sold separately)
To video output
CAUTIO
N
Rear view camera
When connecting the external video component and the display
• It is necessary to set AV INPUT to VIDEO in SYSTEM MENU when connecting the
external video component.
• It is necessary to set AV INPUT to S-DVD in SYSTEM MENU when connecting a
multi-DVD player.
When using a display connected to rear video output
This product’s rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING
• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD
while driving.
This product
External video
component
(sold separately)
RCA cables (sold separately)
Audio input
(AUDIO INPUT)
Video input
(VIDEO INPUT)
25 cm
(9-7/8 in.)
Display with
RCA input jacks
(sold separately)
Rear monitor output
(REAR MONITOR OUTPUT)
To video input
To video output
To audio outputs
20 cm (7-7/8 in.)
Connecting and installing the
optical cable connection box
WARNING
• Avoid installing this unit in locations where the
operation of safety devices such as airbags is pre-
vented by this unit. Otherwise, there is a danger of
a fatal accident.
• Avoid installing this unit in locations where the
operation of the brake may be prevented.
Otherwise, it may result in a traffic accident.
• Fix this unit securely with the hook and loop fas-
tener or lock tie. If this unit is loose, it disturbs dri-
ving stability, which may result in a traffic acci-
dent.
CAUTION
• Install this unit using only the parts supplied with
this unit. If other parts are used, this unit may be
damaged or could dismount itself, which leads to
an accident or other problems.
• Do not install this unit near the doors where rain-
water is likely to be spilled on the unit. Incursion
of water into the unit may cause smoke or fire.
Connecting the optical cable
1. Connect the optical cable and
ground lead to the main unit.
Connect the optical cable so that it does
not protrude from the unit, as shown in
the illustration. Fasten the ground lead
to the protrusion on the back of the
unit.
2.
Connect the optical cable to the
optical cable connection box.
Installing the optical cable
connection box
• When
installing the optical cable
connection box with the hook and
loop fastener.
Install the optical cable connection box
using the hook and loop fastener in the
ample space of the console box.
• When installing the optical cable
connection box with the lock tie.
Wrap the optical cable and connection
box with the protection tape and fasten
with the power code using the lock tie.
Fasten with the lock tie
Wrap with the protection tape
Hook fastener
Loop fastene
r
Optical cable
Screw
Loading...